Problem starting OptiPlex 9020

Similar Questions

• Problem starting OptiPlex 755 (video)

  Howdy all!

  I just got a Dell Optiplex 755 FDF (for someone else).  I installed a Nvidia GeForce 610 graphics card into the PCIe slot.  He started the next time and I was able to install the software and Nvidia drivers.

  The PC was behaving strangely since then. Sometimes it will start fine.  Other times it will start only on-screen vBIOS, who manage the Dell splash screen.  It will be so stay on the vBIOS screen and is not engaged in the POST.  The attached screen is what happens when power on and the system is blocked.  I tested the card in another PC for a few days.  More than a dozen of start ups and not get caught once.  I ran with the 755 iGPU at the same time, he started without problem as well, no gluing.

  So I know it's a problem between the card and the system.  Just don't know what.  I know the vBIOS map is up to date and am pretty sure that THE system BIOS is updated to version A22.

  As this happens randomly, yet often, I am at a loss of what could be a possible cause.  Any suggestions?

  Hello

  Please write to the Dell Community Forum.

  I would ask you to try these steps and advise the result,

  * Since it is intermittent problem starting dell diagnostics from the system and advise the result.

  Also send the serial number of the system via private message so that I can check the system specifications to help you further.

  Kind regards

• PXI-8360 (MXI-Express) PCI-8361 + Dell OptiPlex 9020 = "device cannot start." (Code 10) »

  Hello

  I have a chassis PXI-1050, conencted to a Dell OptiPlex 9020 via a PXI-8360 and a PCI-8361 (identified as 199392B - 01L). It is Windows 7 64-bit. I can't start Windows very well, but MAX can't see all my PXI hardware. The Device Manager has also 2 inputs "PCI standard PCI to PCI bridge" with exclamation points.

  I placed an old FireWire PCI card in the same dwelling and recognized PC. Thus, the slot went very well.

  I transferred the PCI-8361 to an old PC that contains older drivers, and he acknowledged all my PXI hardware. For example, PXI gear works fine.

  What could be the problem? Here's a screenshot of my software OR installed. I think I installed all the drivers I need. I checked NI Update Service; There is no update of Critcal, and only updates and Service Packs listed are 2013 LabVIEW and TestStand 2013.

  

  JKSH,

  I look in that little bit more and think that I now know enough to be dangerous.

  The BIOS allows the PCI Express native control mode in Windows.  PCIe natively do not like some of the architecture when you use the PCI card version, so it disables the bridges on the PXI card.  I can tell that your OS is PCIe natively because it lists one of the ports as "PCI standard PCI Express to PCI/PCI-X bridge" Device Manager like you posted.

  I found that you can disable PCIe native mode, if you want to try it (but in general using the card PCIe is a better option).  Here are the steps:

  -Open the start menu and type "cmd" in the search box; Right click on "cmd.exe" and run as administrator.

  -In the command window, type "bcdedit/set pciexpress forcedisable.

  -Reboot.

  I don't think it would break anything (it doesn't have on a system I've tried).  If you want to reverse the trend, the command is ' bcdedit/set pciexpress by default'

  -Robert

• Loads of boot UEFI PXE not available on OptiPlex 9020 AIO A09 for Win7?

  We prefer to use UEFI instead of legacy for our new systems mode. Previously, we were able to use the active UEFI PXE with SecureBoot disabled and ROMA Legacy boot. The service seems to come and go with each version of BIOS for the AIO 9010, and now on the 9020 AIO with A09, he went as well.

  On a 9020 AIO with A09, if I enable Secure Boot and disable Legacy ROM PXE is available. If I disable SecureBoot (required for the loading of Windows 7) and allow ROMA to the legacy, it has no option to start on the network when you press F12.

  Our new AIOs with BIOS A02 9030 allow us to perform a boot PXE in this way without problem, so I guess that the problem in A09 is a bug and not intentional.

  Anyone else running into this?

  @Community,

  I am pleased to announce that the Optiplex 9020 AIO BIOS A11 is now available to the public. The update of the BIOS A11 has resolved a problem where in A09, the UEFI network box battery inside the BIOS would itself be clear after the release of the BIOS. This prevented the UEFI network protocols appear in the one-time boot menu.

  In short: with AIO BIOS A11 9020, you can now have the legacy option ROM both the UEFI network stack activated at the same time.

  For those who are not familiar with the specific screens in question, I have them listed below.

  Here's the box UEFI would uncheck itself in A09:

  

  It's the legacy ROM option checkbox:

  

  Here's the menu starting time on the A11 with two Roma legacy option enabled and the network UEFI active stack:

  

  The pic then the AIO 9020 had installed A09 and after trying allow the UEFI network stack. You will notice that UEFI protocols are missing because the box UEFI disables itself:

  

• OptiPlex 9020 behaviour during tension (I asked a few months back, but now I see the same thing in another new machine)

  I bought Optiplex 9020 MT a few months back, and last month I get another for my brother.

  I noticed the strange behavior (maybe it is normal) but I want to confirm what is happening when I turn on UPS/Direct connection.

  It will blink DVD, HARD drive, and when the light orange power. After that, it works fine and no problem.

  Here, I have created video for that behavior so it help to what I'm trying to say.

  www.YouTube.com/watch

  When you turn on the power to the inverter, the PC thinks it recovers from a power failure. So he turns himself briefly to see what it is supposed to do during a power failure recovery.

  As stated in the Manual, recovery of the CA in the BIOS options are:

  • Power Off (default value)
  • Power on
  • Last power state

  When the BIOS is set to default, the PC comes on, sees that it is the default and turns off again. That's why you see all the lights are flashing. It is quite normal...

  If you wish, you can set the BIOS to power on so as soon as you turn on the power to the inverter, the PC will boot without having to press the power button.

  To enter the BIOS to make the change, restart, and then press F2 before Windows starts to load.

• OMCI support for OptiPlex 9020 M

  OMCI 8.2.1 will support the new OptiPlex 9020M or do I need to start using the new version of Dell order manage with this new desktop PC?

  Hi EGIROUX,

  OptiPlex 9020 M is officially supported with the Dell order. Monitor and can also work with OMCI 8.2.1. But please start using the latest version of the OMCI - order Dell | Monitor v9.0 for additional features.

• Dell OptiPlex 9020 thin metallic part sff on expansion slots.

  Hello

  I tried mounting of low profile firewire expansion card to my OptiPlex 9020 sff computer.

  When I put the card in it would not fully, glancing thin the metal shield or

  What that either has come down and I had to remove before the card would be

  sit properly. My question is do I have this expansion slot shield plate located on is very

  thin and fragile still.

  It may be leaking RF problems but is otherwise functioning not prevent more than leaving the lid completely turned off.

• Desktop OptiPlex 9020 8.1 of Windows x 64

  I just installed Windows 8.1 x 64 on an OptiPlex 9020 and had graphics using IE11 display problems using the latest drivers from Dell.  The problem was that graphics had a large "X" on the whole of the image.

  I was using these drivers: Intel 9.18.10.3055 06/03/2013

  Then I updated to the latest drivers Windows Dell 8: 24/06/2013 9.18.10.3220

  Display problems were still present.

  I then updated the drivers to the latest Intel (15.33.8.64.3345).  You had to do since the Device Manager as Intel blocks the process of executing setup.exe.

  Also after the installation of the whole machine is MUCH faster using applications.  Just thought I'd share.

  Dell, ETA, when drivers will be updated on the latest platforms to desktop and laptops Dell for Windows 8.1?  I'd feel a lot more comfortable, but there was a Dell "verified" Intel video driver.

  Hello

  You can try with the last Win 8.1 video driver Intel for desktop Optiplex 9020 x64Bit and it is available in the link below

  http://www.Dell.com/support/drivers/us/en/04/DriverDetails/product/OptiPlex-9020-desktop?driverId=YGVRN&osCode=WB64A&FILEID=3325316993&LanguageCode=en&CategoryID=VI

• Adding a second SSHD to an Optiplex 9020

  I would like to install a second internal hard drive solid-state in an Optiplex 9020.  I don't want to use these two drives as a RAID pair.  I want a second disc to be autonomous for the storage of data.  What should I set the Bios to ATA for the second hard drive to be initilized?  I set the BIOS to AHCI and started operating system, but the second disc was not available in the directory.  I set the BIOS to ATA and Windows wouldn't start.  The warning was real.  Replace the RAID BIOS and we are at square one.  I have to leave the game of BIOS to ATA and reload the operating sysem to have two independent drives C: and D:?

  Hi Mike,.

  What you need to do is to use disk management to partition the drive, then it will appear in Explorer.

  Good luck!

• Dell Optiplex 9020 fan slow speed

  Hello

  I'm pointing out the CPU of my Dell Optiplex 9020 and I noticed that the temprature rises and and the fan speed remains the same.

  I used a software monitoring temp to know what is the problem and you can see the main CPU temperature remains low, while the rest of them is much higher.

  Also, the fan speed remains the same...

  

  Is this normal?

  i5 / 16GB / 500 GB/W10 with all the latest news from drivers/BIOS using Dell order Update

  The fan speed when it hit 74ºC?

  The fan speed has increased during the diagnostics, which should have?

  You can go on the Intel site to check what are the temporary specifications for your specific CPU, if that will make feel you better. But same 74ºC seems not very hot.

• RAID 1 on Optiplex 9020 and Ubuntu Desktop 14.04

  Hi, first sorry for my English

  I am trying to configure raid 1 with a dell optiplex 9020 minitower, but at the moment it does'nt work. I have configured raid 1 on the bios and installing ubuntu start but then fail.

  Possible that the od raid controller PC is not compatible with Ubuntu Desktop 14.04?

  Hardware RAID requires a controller. You then boot BIOS and Partition and INITIALIZE the container.

  You start live linux and to partition and to format and install.  You can't do that on the fly during installation.

  The container must be initialized as a single disc BEFORE any os turns.  The container must be initialized as a reader unique regardless of which operating system you want to install.

• SE error message: "Run"DLL"there is a problem starting. C:\Users/John\AppData\Local\Conduit\BackgroundContainer\BackgroundContainer.dll

  Get the below error message every time I start my computer:

  Run DLLS
  There was a problem starting
  C:\users\John\AppData\Local\Conduit\BackgroundContainer\BackgroundContainer.dll
  The specified module could not be found.

  Hello cuefox, thank you very much to judge me.
  We're here to help.
  Continue to browse the web with Firefox, thanks once more.

• Printing in 2 programs problem started 2 days ago, only firefox works fine with Internet Explorer?

  Services Bank web site has a "Print - Friendly View" text, on the top right of the page that displays the account information in a different format if you click on the text. Printing all other functions work ok. The problem isn't when you use them Internet Explorer. The other program is on the Aflacs website, and the problem is very similar. When I click on the text stating "Print copy of invoice", nothing happens, as the text of the Bank. Both work perfectly with Internet Explorer. The problem started about 2 days ago. When it works well, a window will open and show you what it will print and you click on the text "print", and it prints. Any help on this problem will be greatly appreciated.
  Thank you
  Joe Anderson

  You have this problem when running in Firefox SafeMode?
  
  http://support.Mozilla.com/en-us/KB/safe+mode
  
  Do not choose anything at the moment, just use 'continue in safe mode.

  When in Safe Mode...

  • The State of plugins is not affected.
  • Custom preferences are not affected.
  • All extensions are disabled.
  • The default theme is used, without a character.
  • userChrome.css and userContent.css are ignored.
  • The layout of the default toolbar is used.
  • The JIT Javascript compiler is disabled.
  • Hardware acceleration is disabled.

  If this is not the case, see this:
  
  http://support.Mozilla.com/en-us/KB/troubleshooting+extensions+and+theme...

• Satellite C670 problems start after upgrade of Windows 10

  Hi all

  I made an upgrade of Windows 10 but after that my notebank satellite C670 has problems starting. It is always after the Windows updates were installed. It displays the logo of Win, followed of a blue screen. After several ignitions and extinctions I can once again the password login screen. Have already reinstalled Windows 10 because I did not come to the login screen more. But the problems are still there with ignition and extinction attempts it works. But this isn't a solution. You have ideas - drivers for Win10 or bios? Thanks for help

  Hello, I have the problem of the grandmother after the installation of Windows 10 I have nothing white screen
  Impossible to do a spanking Granny restore F8 or F12 nothing to do
  If someone gives you the solution I'm interested
  Thank you, CDT

  
  Validation has been translated by Google Translator

• My iPad has been slow and unstable. What can I do if this is caused by a virus from the Internet because that is what I suspect. The problem started after a message like "scripts to run.

  My iPad has been slow and unstable - it actually seems to be hung when I use it. Once I put it, a blue line with four faces (which forms a rectangle or square) appears on the display and moves as he tries to anticipate my next actions or touch on the scree. All started about four days ago while I was downloading of articles in google scholar. A message that reflects something as "run scripts" or "scripts to run" appeared just before the problem started. Please advise on what I can do.

  Try resetting your device. This will not erase your data stored on that device.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

  If that doesn't work, restore your device to factory settings. Please note that this will delete the data on your device.

  Take a look this Apple Support article: use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support.