Problem the appliance USB VMware ESXi 4.0.0-4.1.0

Similar Questions

• Problem with the start of VMware ESXi 5.0

  I just installed VMware ESXi 5.0 on a new Cisco UCS B200 series blade with two 300 GB hard drives configured in a RAID 1 mirror.  I went through and completed the installation of VMware ESXi 5.0 on this server.  When the installation is complete and the server restarted, he did not initiate the ESXi where I can change the IP address and VLAN.  Instead, I get this text string after the initial boot sequence that is shown in the attachment.  I have a guest who said Shell > do not know why I can not start correctly in ESXi 5.0.  Thank you!  Paul

  Hi Paul,.

  Looks like you boot to the EFI shell. What is the startup policy that you have configured on this server service profile? It should look like the one below.  If there is a problem with the boot order, you should be able to type "EXIT", then enter on the EFI shell to exit the prompt. If your startup is similar to the one below and you still experience this issue, try to downgrade and re - ack the blade.

  Let me know if it helps.

  

• Access to the partition of VMWare esxi

  Problem: I have server with VMWare esxi 4.0.0. Last admin didn' has left a password to get into the operating system. How can I access the files on the repository?

  Thank you!

  Welcome to the Forums - you need to reset the password - here are some instructions on how to do it- http://www.vm-help.com/esx/esx3i/Reset_root_password.php

  Also, I moved this thread to the ESXi 4 forum

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• I want to download the update of VMware ESxi 5.5 3B

  But when I sign up for the trial, it puts me update 2 :-(

  What you've recorded for earlier? This happens when you download the other than approved for products product/updates.

  Same error for me, but I downloaded the recording with the new code. I think that you will need to register with the new code.

  VMware KB: How to download VMware products and troubleshooting issues with downloads

  VMware KB: VMware ESXi 5.5, Patch ESXi550-Update03: ESXi 5.5 full update 3

• IRQ problem the appliance on a 4060XCDT

  I have a problem the device IRQ holder ACPI, here is the System Info:

  IRQ Holder for PCI IRQ Steering ACPI
  System
  This device has a problem: Code = 10 (0xA)
  This device is not present, not working not properly, or does not have all the
  drivers installed. See the documentation for your hardware.
  The registry key: HKEY_LOCAL_MACHINE\enum\ACPI\ * PNP0C0F\00000005
  Alloc resources: None
  Forced resources: None
  Start resources: no
  Filtered resources: None
  Core resources: no
  Driver: System\0024
  Driver date: 23/04/1999

  Can anyone help?
  Win 98SE operating system

  Hello

  Please see this Microsoft support site:
  http://support.Microsoft.com/default.aspx?scid=kb;en-us;182628

  There you should find a solution.

  Good luck

• Hardware error ' problem the appliance ACPI\VPC2004 * VPC2004.

  Original title: problem the unit ACPI\VPC2004 * VPC2004

  equipped with a problem device which has not installed drivers and I am unable to update one

  You have a Lenovo PC?

  Have you tried to update the drivers via update of windows instead of the Lenovo support for your model site?

• Problems, access the Console on VMware ESXi 4.0.0 Build 294855

  I'm having a problem where I can't access the console by pressing Alt + F1 only get the next screen (see attachment) anyone ever see this?

  http://KB.VMware.com/kb/1003677

• Problems with the new host VMware ESXi 5.0

  We have a dell blade chassis, with 4 710 blades and 8 610 the 710's have 12 network cards and the 610's have only 6 network adapters. I added a new host on one of the 610's and two network adapters in each of the networks belonging to virtual infrastructure. 1 mgmt 2. ISCSI 3. vmnetwork

  My problem is that the new host can see all the resources but I can't move the VM from the hosts to the host 610 710. I get an error because nic 2 on the 710 host is not in the same network as nic 2 on the 610. It seems silly that I wouldn't be able to do that just because the hardware is not identicle.

  I have three vswitches, vswitch0 for management, vswitch1 for the iSCSI network of shared storage, vswitch2 for the network of the vm.

  Thanks for any help.

  Steven Reeves

  Systems engineer

  Shasta College

  [email protected]

  Material is not identical not should not have an impact.

  The vSwitch port group to which are connected the NICs in question is named identically on both hosts?  If they have a different name, vSphere considers different networks.

• problems with the installation of vmware esxi 4.0 on pc

  Hello

  I have a pc I am building.

  the motherboard is ASUS P8P67 Deluxe.

  It includes 2 onboard network adapters:

  1 realtek network card.

  1 network adapter intel.

  When I try to install vmware os it shows me an error that:

  "no network compatible adapter found.please don't see hardware compatibility of the product (HCG) guide for a list of the taken addapters supported...".

  Help, please.

  Thank you.

  Ben.

  The easiest way is to get a compatible network card. The "Intel Pro/1000 GT' for example is known as work and is affordable (about $ 30).

  André

• Upgrade of the 3 HP VMware ESXi 5.1 update kills Emulex network and cannot be cancelled?

  People,

  I have a serious issue here after the upgrade of the HP Blade 465 BL c G7 with adapter Emulex NC551i double Port FlexFabric 10 Gb..

  The problem: after the successful online update of ESXi 5.1 Update 2 Patch 5 (2000251) in ESXi 5.1 update 3 (2323236) the ESXi server cannot be crazy, or it can ping to the outside network, so she doesn't have to reconnect to the VCenter server.

  Software/Firmware version:

  The version before the upgrade of the server are:

  ~ # ethtool-i vmnic0

  pilot: be2net

  version: 10.2.293.0

  firmware version: 4.9.416.2

  bus-info: 0000:04:00.0

  ~ #

  Since the version above does not work, I managed to download VMW-ESX-5.1.0-be2net-10.2.477.20-offline_bundle-2541837.zip for upgrade the driver VMNic in: 10.2.477.20 but still after the update and restart the network is not able-ping.

  ROLLBACK:

  I also tried to restore to previous work ESXi Server version 2000251 to the help of SHIFT-R but the ESXi server still restart as 2323236 with a network that still worked.

  
  

  Any other suggestions would be greatly appreciated without having to reconfigure the settings of ESXi and the configuration of the switch distributed from scratch.
  

  According to the recipe of HP/VMware here: http://vibsdepot.hp.com/hpq/recipes/HP-VMware-Recipe.pdf

  There is a note about the NC551i:

  

  / Rubeck

• Problem the installation / setup an ESXi 3.5 for use with rccmd

  Hello everyone!

  As I mentioned in the topic, I tried to install / configure rccmd on an ESXi 3.5 software.

  We have 2 different methods to implement the required functionality.

  1. install a virtual machine to launch the stop on because.

  2 live rccmd with the service console install.

  We decided to implement the 2nd method and everything works except for signal did not go through the process of rccmd listening.

  There is a command to configure the software firewall on an ESX 3.5.x.

  I guess, it's esxcfg-firewall < parameters >

  The Question is:

  Is there an equivalent for the command mentioned in the version of ESXi 3.5?

  Alternatively, if not, how to implement a pass through to close?

  Thanks in advance!

  MGruel

  There are no firewall in ESXi. You will not be able to use the rccmd either. Take a look at http://communities.vmware.com/docs/DOC-9531

  Unless you're on U3 or earlier, you will not be able to use the script but maybe he can give you advice. Have a search in the forums of ESXi 3.5 for the shutdown of the UPS. There are other references.

• Problem with NIC in VMWare ESXi

  Hello, already use VMWare for awhile, but now a doubt arose the advanced configuration of the network adapters.

  I have to do a virtual machine to use as a Proxy. I use a Dell R310.
  I have a card network LAN and 3 for the other internet links. I like to associate each of these NICs for a virtual card, how to do?
  Thanx

  Welcome to the community,

  assuming that you do not use VLAN, create a separate vSwitch for each NETWORK adapter and connect the virtual machine (the port VM group).

  André

• Change the HARD disk in VMWare ESXi 3 Server

  Hi all

  I'm new in the Comunnity. I have the following problem:

  I have a Dell PowerEdge 2950 III with six 7.2 K rpm HDs in RAID 5 running VMWare ESX 3i in an internal USB unit. In this server, I have a virtual machine running a mail server. I have problems of performance of disks in servers and we will change the discs on 15 K RPM drive and change the RAID 10 RAID level. I activated the SSH in VMWare ESXi and my question is: is it possible to copy the virtual machine using Winscp or other method forders, rebuilt my RAID, and then copy these files to VMWare again?

  I'would want to know your suggestions on this matter.

  Thank you very much and best regards,

  Amedina

  You may need to use "add to inventory" since the UUID will be different on the store of data on disks. If we then open the data store with and navigate to the virtual machine. Right click and Add. You answer that you move them.

• Is the PowerEdge R610 Compatible DELL VMware ESXi 5.1 update 1 recovery Image?

  Hi all

  Does anyone know if the R610 is compatible with the recovery Image VMware ESXi 5.1 update 1? It is not on the compatibility list, but the r.620 is there. We use two servers in our VMWare environment and I want to upgrade to 5.1 U1.

  Thanks in advance!

  Lee

  Hi Lee,.

  The long wait has its result.

  Seems that it's a typo. Engineering has responded that it is supported.

  Let me know if you encounter other problems.

• How to configure the IP address on VMWare ESXi 3.5

  Hi all.  I installed the VMWare ESXi 3.5 on a test to dedicate

  Server, assign a private IP = 10.10.1.10 to the VMWare box (this box has 2 physical NETWORK card); and then I

  installed the Symantec BrightMail 9.0.2 as a virtual appliance on VMWare ESXi

  3.5 to act as an e-mail gateway.  BrightMail installation goes smooth.  However, I am not in a position

  to connect to the Internet inside BrightMail 9.  I have installed BrightMail for

  have 2 virtual network card.  Network 1 (eth0) got the IP =

  10.10.1.11, network 2 (eth1) got the IP = 82.132.33.45 (real

  public IP address).  With this settig BrightMail virtual machine is able to talk with the other PC in my LAN, howerver, it can't go on the Internet.  My network configuration is as follows:

  A router (Modem, with the public IP address) is directly connected to the VMware computer (the first NETWORK adapter), and then the VMWare (second NETWORK card) connects to a switch where other LAN PC also connects to.

  My question is,

  1. from BrightMail runs on top of the

  VMWare, how can I BrightMail to connect to the Internet and to the

  Moreover, it connects to my LAN?  Currently the machine has VMWare a

  10.10.1.10 private IP assigned address.

  I'm a bit confuse about the settings of the network on the VMWare itself (I'm not the network

  Guy).  Any suggestion is weclomed.  Thank you.

  the observed range, vmnic0 resembles your DMZ LAN and vmnic1 is your LAN (172.x.x.x) you can check you have the right cable to the correct port?

  then you are supposed not combined two NICs in a single portgroup. you will need to do vmnic0 as a new vswitch with new portgroup named DMZ Lan and change that in the virtual network adapter machine virtual 2 to use the DMZ LAN as the virtual switch.

  iDLE-jAM | SC 2, SC 3 & VCP 4

  If you have found this device or any other answer useful please consider useful or correct buttons using attribute points