PROBLEM WITH DRIVER ETHERNET

Similar Questions

• Problems with ports ethernet E4200

  I have problems with my ethernet ports on my router E4200 V1.  I do not get on flow rate of 12 Mbps on a single connected wired computer.  If I replace it with a simple switch 5 port I get 60 Mbit/s using the same cables.  I looked through the creation and cannot come up with any solution.

  Any help would be greatly appreciated.

  Thank you

  Mike

  OK I tore across the network.  Started from scratch and found the problem.  It is quite strange, but everything works fine!

  I discovered through the process of elimination that the cisco router did not like my Panamax Lan UTP.  Cisco is apparently more strict with the signal than the simple switch or refurbished netgear router.  I had the protection on the power strip 6 Max near the iMac.  The totally weird part is that slowed down the entire network.  Streaming is now pending on 60Mbps at each connection to the local network.

  Thank you all for your time I walked through this weird problem.

  Mike

• Problems with the Ethernet controller and PCI Satellite L30-10 X device driver

  HelloW!

  Sorry for my bad English, I'm from the Russia.
  A few days ago, I bought Satellite L30 - 10 X with W Vista on board. In my opinion, that this OS does ' t very good on this computer, so I install W XP.

  I have some problems with drivers. At first, I don't know which model I have: PSL30 or PSL33? I have download all the drivers for the two models. But after installation, computer doen't find the drivers for the Ethernet controller and PCI device...

  Hello

  Satellite L30-10 X belongs to the series of PSL33E. This number located on the label on the bottom of the device!

  You must choose this number in the form of driver download for XP compatible drivers.
  I put t know why you are not able to install the LAN driver. I have the same laptop with Vista and I've install the XP and all the drivers will work perfectly.

  I assume that you have installed the drivers in the wrong order. Please take look in the Toshiba installation instructions txt file. In this order, install the driver! This is important.

  I think that you should install XP again to ensure that the registry clean, then download and install the XP drivers compatible as mentioned in the installation instructions file.

  Good luck

• HP 655 update to windows 8.1 problem with Realtek ethernet driver

  Hello

  I do an update for Windows 8.1 and now I have a problem with the Realtek ethernet driver, which does not. If I look in Device Manager I see an error for Realtek ethernet driver:

  "Your computer's system firmware includes enough information to properly configure and use this device.  To use this device, contact the manufacturer to obtain a firmware or an update of the BIOS of your computer. (Code 35) »

  I have the latest version of the bios: F.26

  I try to install the driver from the HP site: 8.3.730.2012 HP driver

  also I try with the Microsoft driver: 8.1.510.2013

  Ethernet works fine in any other OS.

  Thank you for you time and I hope that solutions to this problem.

  @all

  Install the new Bios for HP 655 compatible sound

  http://h30434.www3.HP.com/T5/wireless-Internet-home-networking/Realtek-Ethernet-driver-error-code-35-Compaq-CQ58-Windows-8/m-p/3208099#M53864

  655 HP

  Updated HP Notebook System BIOS (AMD processors)

  Version:

• HP 255 G4: Problem with Driver Usb

  Hi, I have a problem with my HP laptop. Two usb ports do not work because it is not the correct driver.

  Help, please!

  [Personal information]

  Product: M9T13EA #ABZ

  Good bye

  This problem is really stubborn...

  OK, time to pull out the artillery heavy.

  Download and install both of these drivers and reboot and see if that takes care of the issue.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=7834528 & swItemId = ob_154066_1 & swEnvOid = 4059

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=6943835 & swItemId = ob_133037_1 & swEnvOid = 4059 #tab1

• Problems with drive HARD Toshiba MK1234GSX

  Hello

  I have an Acer with a secondary HD TOSHIBA MK1234GSX 9920.
  Since I installed Windows 7, I have problems with the HD.
  Upon restart, the HD is considered as having problems with windows: when I look in device management, I have this message "Windows has stopped this device cause it has problems. (Code 43) »
  I did a full scan (chkdsk), but no not found errors.
  If I turn off the HD, reactivate and restart, sometimes I can access the HD which works perfectly.
  Does anyone have an idea on this?
  Thank you.

  PS: Sorry for my English :)

  CHKDSK is not good to test a HARD drive for bad sectors, its only good when looking for errors of the filesystem (FAT32 or NTFS).

  Test the hard drive to find errors using DFT.
  DFT download: http://www.hitachigst.com/hdd/support/download.htm#DFT

  Download the ISO file and burn it to a CD - R disc (there is also a version on disk if it's easier).
  If you don't know how to burn an ISO file, read this guide: http://www.petri.co.il/how_to_write_iso_files_to_cd.htm
  Restart your laptop and boot from the disc of DFT.
  Choose the 'Advanced' test and let it run (it may take an hour or two).
  If you see a message in red box, the HARD drive is faulty.
  An error code 0 x 70 means there are bad sectors and the HARD drive needs to be replaced.

• Satellite P100-221: problem with driver battery composite microsoft

  Hello

  I have problem with my satellite p100-221! A few days ago I had problems with my audio driver (audio conexant high definition), after starting it was indicates that the pilot of his failed to initialize, I reinstaleed this driver several times and at last it was working OK, but I noticed that windows does not see the battery.

  The small cell in the status bar disappeared and I can not say for how long can I use laptop with battery. Laptop works as if it is connected to the AC. In the Device Manager appeared an exclamation on the battery composite microsoft.

  I tried to renew the drivers but nothing. I deleted combatt.sys and cmbatt.sys in windows\system32\drivers but they appear again. I started in safe mode deleted, but after normal start, they do not appear. I also deleted them in Device Manager, and after start-up, this device did not and do not ask me to install the drivers.

  What can I do?

  Hello

  I noticed that you did a lot of complex changes to your device. You deleted some files, update drivers, etc..
  I guess that your operating system has been enough installed and worked properly.
  Windows XP supports a system restore tool. This tool allows you to roll back the OS to the beginning.
  In my opinion, you should try to use this option. Maybe he'll bring your laptop at the time where everything worked correctly.

• problem with drive Intel HD 520 - bad resolution

  Hello

  I bought the HP Pavilion 13-s104ne model and I am facing problem with the resolution.

  some msg boxes are not clear, it looks like to scanned box, I am really very angry about this and I need a solution...
  I tried to unstall and install the driver but nothing changed...

  Please help me

  Medhat

  medmarai

  Hello;
  
  Let me welcome you on the HP forums!
  
  I read your post about resolution issues and wanted to help.

  Since it is a machine relatively new, instead of hurt for hours to fix yourself, why not just let HP fix it - for free!
  
  You must contact the HP Customer Support directly so they put you in contact with HP Tech Support to see what they can do on the diagnosis and repair of your machine remotely.
  
  I did recently, and HP technology was able to remotely access my PC on the Internet and to make the necessary repairs.
  
  If you live in the United States or the Canada, details are on this page: http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
  
  If you live elsewhere, contact details are on this page: http://www8.hp.com/us/en/contact-hp/ww-contact-us.html
  
  NOTE: once you get through, stay on the line until you are finally able to talk to someone ' one - it can take a while!
  
  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• Problem with driver with Agilent 6031 A feeding

  Hello and goodmorning,

  I tried to develop my first application of cvi in which I need to use a power supply (model Agilent 6031 A). I first use direct command of GPIB and I managed to make it work, but with some difficulty, due to the fact that sometimes orders are missed.

  So I downloaded the driver from the website of OR, and I tried to implement in my code. I found a problem with the first statement, the init it. Here is my code:

  ViPSession InstrumentH;
  
  ...
  
  ...
  ...
  
  All = hp6xxxa_init ("GPIB0::5:INSTR", VI_ON, VI_ON, 1, & InstrumentH);

  After running the above code, I found in 'All' value '-1073807339 "and InstrumentH is equal to NULL."

  Any idea and advice would be much appreciated.

  P. S.

  There is a way, as in Labview, to find the explanation of the error Code?

  Found the problem. Food must be set of SCPI commands on the old controls ARP using "SYST:LANG".

• Problem with Driver Audio (Audio beats) HP Pavilion dv7 6190sl

  Hi guys,.

  my name is Francesco and I have a problem with the sound card in my PC...

  After formatting the PC, I reinstalled all the drivers, even if the installation is successful, I can't hear sound from my pc...

  Unfortunately, I deleted when formatting the disk that contains all drivers... (HP_Recovery)...

  You have a solution?

  Thanks, Francesco!

  Hello

  Open windows control panel, open Device Manager and open sound, video and game controllers.  Right click on the IDT device and select Properties.  Click the driver tab and then click on "update driver".  Select "Browse my computer for driver software", then "Let Me pick from a list of drivers for devices on my computer.  "High definition Audio Device" left click once to highlight, then click the next button to install it.

  This makes all the difference?

  Kind regards

  DP - K

• Problem with drive HARD and Vista install

  Hi all

  A few weeks ago, my Dell Inspiron laptop computer started to freeze. I could boot ok and my desktop wallpaper and icons were all there, but I couldn't run or open anything. I did the Bios tests and my Vista installation disc and told me there was a problem with my hard drive. I wiped it and tried to reinstall vista and that I could see it wasn't working because it took hours and then seems to have stopped again during installation. So I bought a new one and tried to install Vista. everything was going well until it is restarts a second time and I got a black screen with a mouse pointer icon. I had to reinstall it running for about 4 hours, at least an hour of that time which was all that was going on and the hard disk wasn't spinning.

  How long on avg would take to install Vista, if it is running normally?

  is there anything else that might be a problem that would not appear in the repair of Vista or Bios diagnostics?

  Any advice would help a lot.

  If the new hard drive does not work, then the problem is on the motherboard. Your description of symptoms indicates a power supply or motherboard failure. Contact Dell technical support for repair or replacement. MS - MVP - Elephant Boy computers - don't panic!

• Problem with drive blu - Ray and Hulu plus.

  On my TV I get the first screen of Hulu - more, but is unable to play the video. Get error 5003. No problem with Netflix or YouTube. Use the activation code. Impossible to get a sign in screen t.v. for hulu-plus I can see it on my iPad.

  Hi Twolips41! Thanks for the post. Please try the steps listed in this article , and then try to connect to Hulu Plus still.

  If my post answered your question, please mark it as "Accept as a Solution."

  http://bit.LY/win-4k

• Problem with the Ethernet driver on the computer.

  My computer running Windows 7. I have trouble with my USB ports, so I wired my computer and use my Ethernet port. I had problems to have to set my modem every time that I got online and now I simply cant. When I diagnose the problem, he says I have to install the driver. I have not uninstalled anything. My computer does not recognize the modem. I am able to connect wireless currently but I really need to use the Ethernet port and move my computer on my living room floor :) I'm trying to figure out how to download or reinstall the driver?

  Try to update the drivers for hardware pc/software, so intel based pc, go to

  intel.com/support/software/drivers.Either run the utility intel who sweeps

  any intel based pc for all updates, or locate manually. The chipset «»

  utility installation' would be 1. It controls sound/USB/eithernet, and

  other hardware on the pc... Intel should also have the 'networking '.

  drivers, all being that its mainly based on intel. Otherwise, go to the pc mfg

  Homepage

• Serious problem with driver i810 Equium A100-306

  I have a new Equium A100-306 and I try to install two different Linux distributions:
  10.1 (x86_64) SUSE and BlueWhite64, but in both cases, I met the same problem:
  When you restart the Xserver, the computer stops responding.

  I used the i810.
  This is not the case with the vesa driver.

  lspci reports:
  00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub (rev 03)
  00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS/940GML Express Integrated Graphics Controller (rev 03)
  View 00:02.1 controller: Intel Corporation Mobile 945GM/GMS/940GML Express Integrated Graphics Controller (rev 03)

  Hello flora

  Before you wait here for a long time trial learn more about Toshiba Linux pages:
  http://www.Linux-laptop.NET/Toshiba.html
  http://Linux.Toshiba-DME.co.jp/Linux/index.htm
  http://newsletter.toshiba-tro.de/main/index.html

  Good luck!

• Problem with IRQ Ethernet q150

  I'm trying to use an IdeaCenter Q150-40813AU with Linux (Centos 5.5) However, I have an IRQ error at startup which generates the temporarily unavailable "SIOCSIFFLAGS resources" message when you try to load the network driver.

  I tried the Plug n Play OS BIOS in two possible settings option; However, there is no change in the situation.

  Y at - it a firmware updated BIOS controls the IRQ option, which allows the configuration of each IRQ?

  Not finding not all useful information online, I tried the reset for default option instead of the change of plug-and-play and the problem disappeared.

  View this as closed.