Problem with HP LaserJet P1005

Similar Questions

• Problems with HP laserjet 8100 printer.

  After weeks of no problem my hp laserjet 8100 will not print.

  Doc Gets the queue and either; test pages do not print either.

  I have windows 7

  I followed the usual stuff with msc.services etc. but nothing helps

  Please someone help - the only problems I ever is where electronic mechanical meeting! That is, printing, scanning

  Hello

  Uninstall and reinstall your printer by using the drivers and information on the HP website.

  Equip your model number of the printer there for information and troubleshooting for her.

  http://WWW8.HP.com/us/en/support-drivers.html

  Or ask in the Forums of HP's Support.

  http://h30434.www3.HP.com/PSG/

  See you soon.

• Problem with HP LaserJet Enterprise 500 MFP M525

  Hello, I have a problem with my printer LaserJet. 49.38.11 error on the printer and it rebooted several times. Can you help me with this?

  P.S. This thread has been moved from LaserJet MFP and all-in-one - HP's Forums moderator

  Maybe a "corrupt" impression containing poorly formatted PCL who cannot deal with the trainer.

  If you unplug the printer from the network and USB (if applicable), then poweer-cycle of the unit, the same thing happens?

  If so, this would imply a flaw with the printer.

  If this isn't the case, it implies that a rogue print job is sent to the printer each time that it is powered - on, which causes a fatal error in the printer, which restarts automatically, and the process then begins again.

• Problems with nine LaserJet 1102w

  I've had my LaserJet 1102w for two days now, and I'm so far regretting buying and considering it return.  Here's why:

  1. it turns off automatically after 10 minutes and do not print after that until someone manually pushed the power button.

  2. when it is turned on, it will display only the first inch of a given page (Config test included integrated page), then it is the orange light flashes.  If you stop and then turn it on again, try again, and then turn market a SECOND time, it will print normally.

  3. it consisitantly fails to print "big" files (I quote because he isn't that great... i.e. a 32 MB PDF)-they gets stuck and require a complete restart of the printer.

  Is the only issue that I don't see to have fall wireless... which is good because we have not ALL wired devices in our House (which is why I bought this printer... most of the devices are iOS, but I'm working on Win7 laptop at the moment).

  I would love some advice or help get this printer to work.

  Thank you!

  * EDIT: I did so, it is updated the firmware lasted and I use the driver to date, both gets on the HP site.

  This looks like a problem with the mode 'sleep' on the printer.  There are a few things you can do to try and fix this problem.  First of all, make sure that the printer is connected directly to a wall outlet.  If you plug it into a surge arrester, power strip, or rescued food, it can prevent the printer to get enough power.  If this is correct, then proceed to try the steps in the document following the link.  If nothing works, contact HP to see on a replacement printer, or return the printer to where you bought it, be it, you need to replace the printer.

  The printer will not turn on or respond

• Problem installing HP LaserJet P1005

  Hi all

  I have had to install the software for my second pc, but has encountered a problem which I was unable to complete the installation. Everything was fine until that part when I was prompted to plug in the USB cable and turn on the printer. After I did it, the only option available for me to go forward is to 'return' ('Cancel' option is gray).

  Can someone please help?

  Thanks in advance!

  I had the same problem with my PC to 8 window when installing printer HP Laser Jet P1007. I was just at the link below and it worked fine.

  http://support.HP.com/us-en/document/c03646498

  Kind regards

  Raju Mani.

• Color Laserjet PRO MFPF 377dw: problem with Color Laserjet PRO MFPF 377dw and HP network scanner

  After removing the package of printer drivers HP, all attempts of resettlement via WLAN regularly fail before the end, which indicates that the device is not found. I physically connect the printer to the computer by USB cable to install the software successfully. When I go to WLAN Wireless thereafter, the printer works perfectly within the network. If I remove the USB cable, the following error message appears when I try to start scanning HP: HP CLJM377 Scan found . In other words, HP Scan cannot be used with a PC not connected by USB cable. All other remote features function normally printer in wireless, including HP Scan & Capture. Is there a possibility to correct this, via the Windows registry from my PC?

  MrRobot wrote:
  

  Hello! @Chirsistei, your description of the HP product is classified as a commercial product (business). Our sales support team provides support via the channel of entry here. If you need immediate assistance, you will need to open a session one business with our sales support team. Click on this link http://ow.ly/I3gw30140F8 for more details.
  Let me know if you want more information and/or assistance.

  Have a great day!

  See you soon!

  Hello Chetan,

  I think I'm in the wrong forum here because I live in Switzerland and here the Laserjet Pro M377dw color is sold to private users. I have no access to a support plan and use the printer in my home office network. Your proposed solution therefore does not help me, during this time, I have posted this problem in the forum on language German you need not to pursue this new. Thanks anyway

• Problem with printer Laserjet 4 M Plus printer

  I have a Laserjet 4 M Plus printer which I had connected directly to my office with Windows 98.  The printer worked fine with the office.  Well, I've upgraded the desktop of Windows XP and now I can't the printer to print at all. The printer has been added to the desktop, but it will not print a page to test the computer or any program at all.  Your help is greatly appreciated in getting my printer works with XP.  Thank you!

  Message edited by cvanderhoef on 12/21/2008 13:28

  Let this step by step, as we do for the 1st time

  1. set up your printer (cords & cables)

  2. turn off the computer

  3. connect the parallel cable or usb

  4 turn on the computer

  5. turn on the printer

  6. place the disc in

  or install from windows printers list

  Download of HP or

  7. open the folder "default" printer

  8. check the cable port

  example: printer properties

  tab select "Ports".

  9 look for ports using its

  the ports are: "the LPT1 printer Port:

  "USB: printer name?

  Make sure that the port is checked in the box of

  10. click on the "General" tab > "printing preferences...". »

  11. Select "advance" tab tick to set lower resolution

  that i had this problem on one of my printer

  because the high resolution would never print

  12 OK and test print the printer if successful

  13. click OK final

  14 perform the normal functioning of every day as everyday u

  15. good luck

  Message edited by rickp400 on 06/01/2009 12:49 AM

• Printing problems with HP LaserJet 4050 TN

  Hi all

  I have a HP LaserJet 4050 TN and I connected on my desktop Dell (8 64-bit Windows) with a parallel cable / USB (TrendNet 1284).

  When I try to print, nothing happens (eventually I get an error message from Windows 8 on the right that says: "error of HP LaserJet printing...) The printer could not print").

  The printer is on, of course, and it is able to print (for example, test configuration page prints very well).

  From the printer connection, looks like it automatically installed the HP LaserJet 4050 Series PCL 5 driver.  I tried to update and it says that it is up-to-date.

  Any ideas what the problem may be?  Thanks for any help you can provide!

  ----

  Edit

  ----

  Just to add that this printer model seems not support a network connection for the HP site. I try the parallel-usb connection since it seems to be the only option to connect the printer to my computer.

  More that likely the IP you have assigned manually whenever you got the printer. The Jet Direct card is when you connect the ethernet cable into the printer. I have 2 screws in the top and bottom.

  What I would do is a cold reset so your home network could affect its own IP address.

  With the printer off, press the big green button, and then turn on the printer. Wait what he say cold reset on the display, then release the button. Connect your network cable, wait about 1 to 2 minutes for DHCP to assign an IP address and print a configuration page. The second page will show you the IP address.

  Then go to your driver, click on Ports and change the port to a Standard TCP/IP port. If it is not available, then create a new port. Enter the IP address of the printer and print a test page.

• Problems with the LaserJet M1217nfw MFP - resolution of the Scanner and ADF feeding issues

  Feature: LaserJet M1217nfw MFP

  Connection: Ethernet

  OS: Windows 7 Pro 64-bit

  1st problem: using the TWAIN software, I am unable to change the resolution of the documents I'm scanning. It displays only the 300 and the menu drop-down does not offer any other parameters. It is having to make each document that I scan a lot more big that it must be, and the company I'm downloading of complained them of the overused storage space.  Device MUST be based on the network for the office.

  2nd problem: the ADF is VERY picky. If the paper is inserted at the stop, it will not pick up and will keep scanning out of the original glass. I usually have 2 or 3 times to find the "sweet spot" where it will actually be a new Pick-up analysis.

  I must say, I was very happy with this product when we got it first, the web interface with the drivers loaded on the printer was a great feature and the installation for each machine went very smooth. However, lately this device became more complicated than a time saver.

  Hi SilentbobSC,

  Follow the steps below.

  1. click on settings

  2. remove the checkmark of "Display the dialogue from TWAIN to allow cropping and low sweep"

  3. click on the drop down arrow to adjust your ppp settings

  

• Problem with installing Laserjet P1102W - Ad-Hoc - can't change mode of Communication of Ad Hoc

  I have a printer HP Laserjet P-1102W which was installed in Ad - Hoc mode for a short time.  The unit can, however, connect via USB and works very well in this mode, but I want to use it as a Wifi unit with my router and the APs. The unit has a 20130703 firmware datecode. I need to reset the mode of communication out of the "Ad Hoc" mode.

  With the printer is NOT connected through the USB port and holding down the 'X' button to print the "Self Test / Configuration of the device"sheet shows that the status = not connected. " The MAC address displays address 12 characters, the IP address is 0.0.0.0, as is the subnet mask and the gateway. The "IP configured by Hand with the server DHCP/BOOTP = 0.0.0.0 =. The 802.1 b / g Wireless Status = Enabled and the Communication mode = Ad Hoc, SSID = HP4FA96D with authentication = None (open).

  I tried to reset the unit by pressing down the wireless and 'X' buttons located on the top of the machine, but this action does not change the mode of further Ad Hoc communication. I looked through the USB print driver in Windows 7 Pro, but can find no access to wireless settings, and as the camera doesn't have an IP address, I can't access the built in web server.

  Any suggestions on how to completely reset the unit so the Mode of Communication is NOT "Ad Hoc"?

  Concerning

  IT IS FIXED - READ BELOW:

  After trying the patches recommended by other users, download the latest firmware, the driver more current and also help in the HPPSdr.exe of the HP program, making a unit restart by pressing both buttons when the device has been propelled to the top (this is only a partial and not completely reset reset) the unit would not clear the AD - Hoc mode and return to the wireless infrastructure mode.

  The last step, I tried (without the help of HP or the community) was to find the original disc of 2009 and first install it like a USB connected printer. If successful, then a second set with USB cable attached as a wireless printer. It helped me finally change the settings DHCP wireless, assuming, SSID, etc.. Once completed, and unplugged the USB cable, the printer now works as a printer wireless assuming with my router and access points.

  We have NOT ALLEGED on HP support pages for this printer trying to use older software install the disc and make a several step installation - shame on HP!

  The community of HP came with some good ideas, suggestions did not fix of unfortuantely this problem. The printer is out of warranty, so HP Corp. would NOT  provide any help (by e-mail or otherwise) unless I used either the HP community or pay them $24.95 for once call phone support. It seemed stupid to pay 25% of the new value of the printer four years ago.

  Given this bad experience with the lack of support for current HP products which exceeded their warranty period, I can't recommend HP products to my clients or friends. Shame on HP for this contempt for their customers!

  Peter

• Printing problem with HP Laserjet 1020 on Windows 7 with or without network

  I just upgraded all my computers at home with Windows 7 Professional and just set up the network for shared printing.  On my main computer where the network is hosted (to connect to the printer, router, etc.), all the drivers installed and seems very good and computers on my network have all the necessary drivers installed. Currently, my HP laserjet 1020 printer is visible on all systems and print jobs are visible too even when I tried to print it, just document is located in the area waiting for the print window and do not print.
  I tried the printer troubleshooting tool, but it could not pick up any problem anyway.

  My two machines running windows 7 Professional 64-bit.

  Someone has an idea, what happens? I used to be able to print fine on the network when I was with windows xp professional (32-bit)...

  Hi th911,

  You mentioned that you have installed the latest drivers from HP, you have also gone through Windows Update to ensure that you have the latest updates installed as well?

  Please see the link below for more information on how to do it:

  http://Windows.Microsoft.com/en-us/Windows7/install-Windows-updates

  Also, here is some good information about setting up the printer on your home network:

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer-on-a-home-network

  I hope this helps! Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• HP LaserJet P2055dn: Feeling strange problem with HP LaserJet P2055dn

  This printer has worked almost flawlessly, but, suddenly and without apparent reason, it does not print a document just created in WordPerfect, something that has never happened before. The document is simple text - using Gnuolane Rg, a police, I found and downloaded and which worked very well in other documents recently - and this document does not no unusual formatting. The printer is fine with everything else, including other documents using this font.

  The it is attached to the computer is a Dell Optiplex 745 Intel Core 2 CPU 2.40 GHz, 4.00 GB of RAM, running Windows 7 Professional 64-bit, Service Pack 1. No warning message is appeared on the computer screen or the display case in the printer. No hardware or software changes have been made. The printer connection is by USB. This computer is fast enough and it has worked very well since I bought it. A if the printer, one produces really good, so far.

  As I mentioned above, there is nothing said in the printer display. The printer prints the error message, instead of printing the document:

  PCL XT error

  Subsystem: TEXT

  Error: IllegalFontData

  Operator: text

  Position: 117

  I tried the "quick fixes" that usually work for typical problems: restart the computer, restart WordPerfect, restart the printer, change the name of the file, save the document in a different file. The printer utility shows no documents in waiting and no warning or any other manifestation of boredom.

  Hello, the easiest fix is to change the PCL 5 PCL 6 driver. PCL XL error is one of the many problems that PCL 6, others include empty gibberish, advertising page before each use.

  I hope this helps...

• LaserJet P2035: Problems with a LaserJet P2035

  I have two HP LaserJet P2035 and both will send jobs not from the paper tray.  They two fine prints from the manual feed tray 1.  When I close the manual feed tray 1 and try to use the paper in the paper tray, the paper light keeps blinking and will not clear. I have performed the update of the firmware on the two units that made no difference.  I would greatly appreciate any suggestions.  Thank you!!

  Thank you freginold.   I found the culprit.  I have slightly bent a metal cross bar support located under the paper tray upward toward the printer.  This bar triggers the lifting of the paper tray mechanism to lift the paper in place and of course, there was no contact. This solves the problem.

• Problems with HP Laserjet Pro MPF475dn 400 ADF

  Our printer does not have the paper when it is put in the ADF, sometimes, it takes the paper (about 1 out of 10 times), but especially he refuses to juice to pick up the paper.

  How we solve this problem?

  We have already updated the firmware to the latest version, clean the rollers, but nothing seems to help you.

  Who can help us?

  Lebotec

  Hello @Lebotec and welcome to the Forums of HP.

  I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a commercial product. You can do to Commercial Forums of LaserJet HP.

  I hope this helps!

• Problems with HP LaserJet 1100 print printer windows 7 (64)

  I have a LaserJet 1100 HP printer and I bougt the printer cable USB/Minicent garage and reconnected the PC in an operating system of Windows 7 (64), Theplug and game need not recognize the PC and try to install it that way is suggested in the HP site but I got going in circles throuught pahges without success. Finally I found a diver and it installled hav it, but I have a question: in the Pinters loaded appears and HP 950 IEEE1284 controller and the HP Laserjet 1100, I tried to delete this 950aand HP cannot be

  I watched the HP1100 installed printer and I saw all my documents in the what... I removed most of the ten but one a test page and can not move and does not alow the printer to print correctly.  I went to another site and gave to Ms. driver and I installed it and now the shoewn of the printer are LaseJet HP1100 LaserJet HP1100 (MS).

  Once again in the default printer, the HP 100 when the test page has been sent is always stuck in Quebec and can'tdelete or print.

  I made the default LaserJet HP 1100 (MS) and sent a test page and print it.

  The question is which printer can I leave the HP 1100 as defauly the (delete or leave) or the HP LS 1100 (MS)?

  Has anyone had this problem before?

  Any s suggestion comment I appreciate them. Thank you

  Clearly your message not being your comments on the web site of Microsoft Answers, then I have it to this forum the forum of 'Hardware and drivers' Windows 7.

  Visit the page of your printer on the guide of the Microsoft Windows 7 compatibility for your printer here: http://www.microsoft.com/windows/compatibility/windows-7/en-us/Details.aspx?type=Hardware&p=HP%20LaserJet%201100%20Laser%20Printer&v=HP&uid=C4224A&l=en-US&pf=0&pi=0&s=laserjet%201100&os=64-bit. You should see a link "Free download required. Follow this link. It leads you to a driver?