Problem with the cisco 5510 port mapping

Similar Questions

• Problem with the Cisco VPN and Vista client

  Hello

  I have an easy VPN server configured on a c2811 and users use the Cisco VPN client. Lately, I have users running Windows Vista 64 bit and I need to know what is the correct version of the vpn client, I have to use and the compatibility problems with the server, I configured.

  Thank you and best regards.

  Cisco VPN Client doesn't have any version that is compatible with Vista 64 bit OS. The only customer that Cisco has released that supports the 64 bit OS's AnyConnect, but it is only supported on the CISCO ASA Appliance

• problem with the bytes to port to read in VISA

  Hi guys,.

  I'm reading device data using usb - BT dongle. It creates the virtual port and read without problem.

  My problem is the packages to send 428 bytes, inside this block device, I have 400 bytes of data bytes 9 to 409. The first 3 bytes of each block is the same.

  4 45 50 - MEP, they are the first 3 bytes of each block of 428 bytes.

  Okay, if you check the vi I config the visa and sending the data of adjustment of the device, read the answer and it sends the data to start sendding data.

  Well, I try to read each block of 428 and show in a chart.

  The problem is sometimes bytes in ports are 428 and anothers shows 23, 2, 125,... is not continuous 428 bytes each iteration and destroy the data graphic.

  IF I check the chart outside of the main loop, I see the correct graph. Apart from mainvi I collect whole data and separate in 428 blocks, extract the 400 bytes of data and analyze the entire signed 16 bit and display in the graphics.

  So, I don't know the best way to get 428 bytes in each iteration... I tried to read directly the 428 bytes but sometimes fail once again, very low reading bytes... take time to wait before read bytes to each iteration. I need a way to get 428 before values to get the readings of 400 data. Even I could probe each beginning of block with 4 D 4550 HEX bytes to pass and got data...

  Perhaps it would be better to use the wait? or using a while loop to wait until I had 428 bytes? Any help will be apprecite.

  Best regards, Fred.

  You receive binary data.  Therefore, turn off the the stop character.

  What happens is that you actually 0x0D in your data.  Playback VISA who sees and then request's made it reading the data.  By turning it off, then reading VISA will read all 428 bytes or until a time-out occurs.

  Let the constant instead of the bytes to the Port.

• Problem with the Cisco ASA 5525 X SFR and Firesight high school

  Hi team,

  We have two ASA 5525 X installed on them and Firesight in a Linux VM whose two SFRs are registered with SFR failover mode. We use the SAA secondary off the hook if the primary fails to turn on the secondary manually switch the wan cable. I turn on the ASA secondary every weekend to take the configuration of the primary for the ASA and the SFR and close by button walk / stop.

  Last week I turn on high school ASA and the Firesight couldn't see the secondary SFR and show the message below:

  Module device heartbeat: device > don't send heartbeats.

  (I should mention I can Pinger the IP ADDRESS)

  I tried to study the problem without success.

  I also deleted the sensor just Firesight devices management in case something is stuck, and I'm trying to re added without success.

  I'm new in firepower so... any ideas?

  Thank you

  Finally, this problem has been resolved by the redefinition of firepower:

  see detailed here procedure to perform this redefinition;

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-firepower-service...

  Before that, it appeared that firepower was not very healthy:

  After a success "" configure Manager add xxxxx"command.

  the command of managers show show nothing;

  He should have shown this result:

  > Display managers
  Host: 193.193.2.75
  Registration key: AZERTY
  Inscription: pending
  State of the PRC:

  on the other hand, in expert mode, the following command shows several processes (and not in the normal state):

  sudo pmtool status | grep-i down

  Last point,

  After the recreation and reconfigure all this fire power, installed in the ASA secondary standby, was considered to be OK under Firesight health Monitor,.

  but after 10mins, it appeared in critical condition with the following message:

  "Interface"DataPlaneInterface0"receives not all packages.

  This is normal and due to the fact that Eve ASA receives no flow and the same goes for firepower inside this ASA;

  by performing a failover from the primary to the secondary ASA, this critical message disappeared for firepower inside the ASA Sec and appeared for firepower inside the ASA elementary school

• Problem with the Cisco ASA vpn redundancy?

  Hi all

  I have a series ASA 5500 firewall and need to set a different peer ip for the connection of site2sitevpn. In fact, my goal is, ASA tent first pair ip of the site2site tunnel, when ASA may not reach this ip, try to reach another ip I set before. I can configure this scenerio on Cisco router with this command;

  
  
      crypto map tohub 1 ipsec-isakmp 

   set peer 10.1.1.1 default 

   set peer 10.2.2.2
  
      

  but I wonder what can I do about ASA?

  Thank you.

  Best regards.

  Shane,

  You can configure multiple IP addresses, under the same entry of homologous set on ASA, but it works the same on IOS with preferred peer, it passes between defined peer.

  Marcin

• PIX 6.3 SNMP MIB, problem with the CISCO-PROCESS compilation - MIB.oid

  I am Edgar Servín

  I have a cactus and got to watch the CPU of the PIX, I got the OID number:

  cpmCPUTotal5sec 1.3.6.1.4.1.9.9.109.1.1.1.1.3

  I used the Cisco SNMP Object Navigator and said:

  Compile the MIB

  Before you can compile CISCO-PROCESS-MIB, you need to compile the MIBS listed below in the order listed.

  Download all of these MIBs (WARNING: does not include non - Cisco MIB) or view details about each MIB below.

  How can I do?

  Hi Edgar,

  compiling the MIBs is necessary only when you are using HP OpenView or something similar. With the cactus, I confess that I have never used myself, but I'm pretty confident that you can just set the OID in Cacti and it will just make a periodic SNMP query for that object.

  HTH

  Herbert

• Problem with the keyboard in port p/s2

  When installing a different usb mouse, I accidently deleted the keyboard of the p/s2 port cable until I turned off. Now lights all flash at the start, but after that he didn't no response of the keyboard. I tried a second keyboard p/s2 with the same result. When I go to Device Manager there is no installed keyboard and when I check the properties, there is no listed keyboard. Is it possible to check if the port works, from a command prompt, or something, as ever, I can't work around boot to enter the bios setup?

  Have you tried a USB keyboard as function of the age of the system most BIOS will support a default USB keyboard. Windows itself will be a little while (about 30 seconds) to recognize the keyboard, but he eventually set up the driver.

• Since 10.11 I have not been able to download via the usb port of my Davis Vantage weather station. No solution of tech Davis on the issue even with the new recorder of events in the resort. Is there a problem with the usb?

  Since 10.11 I have not been able to download via the usb port of my Davis Vantage weather station. No solution of tech Davis on the issue even with the new recorder of events in the resort. Is there a problem with the usb?

  What Mac? (details)

• Re: Satellite C650 - problem with the devices connected to USB ports

  Hello

  Can help someone, I have a C650 and everytime I try to connect to something to him via the USB ports, it is not "found" by the computer?

  The other night, I tried to get pictures on my phone but it wasn'; work and I put it down to a problem with the phone, but today I tried to install something digital crafts for my daughter and during installation it tells you to insert the thing into the USB port and click Next, when I do that he's going through a lot of "research" and said then it can not be found.

  The laptop makes a beep sound as it would on an extraction device when you plug... I hope that makes sense. So I am now assuming that the problem is with my computer, is there something I can do to fix this?
  Thanks in advance

  Sorry should add - it's like nothing is plugged at all when it is, and it happens on two USB ports, not just one...

  Post edited by: leahhw123

  Hello

  What happens with plug n play like USB mouse device?
  You are able to use an external USB mouse correctly?

  > but today I tried to install something digital crafts for my daughter and during installation it tells you to insert the thing into the USB port and click Next, when I do that he's going through a lot of "research" and said then it can not be found.
  I guess this could be a problem with the software or drivers installed.

  I searched a bit and his city that he has a software is compatible with windows vista/2000/xp. Win 7 is not mentioned do not know if this could be a problem, but in your case, I recommend asking the support of this software product for some advice.

  In addition, you can try to install this software once more, check whether this USB problem appears again.

• Problem with the ISATAP #3 map

  Hi I have a problem with the ISATAP #3 card. I read a previous thread who recommended to uninstall and then put it back, which I've tried, but the pilot does not re - installed. Can someone help me with this? Thank you

  Jack

  Hello

  Control Panel - Device Manager - do a right-click on the two - UNINSTALL - REBOOT

  Nothing else to do, Windows will do the rest. And you can ignore the errors altogether if you want and
  on some computers, it will always be there but don't cause any trouble.

  On a Windows Vista-based computer or on a Windows Server 2008, Microsoft computer
  ISATAP map appears with a yellow exclamation next to it in Device Manager and you also
  error message.
  http://support.Microsoft.com/kb/932520

  Check the answer by Diana D. here:
  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/a75e8bf1-9a63-4CF4-BF6C-d43a26175959

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• 3 laptops different ALL been facing intermittent problems with the USB ports.

  We have 3 laptops at home, running 3 different versions of winsows 7... Home, Professional and Ultimate. They have in recent months ALL given intermittent problems with the USB ports. A device that worked on a port stops working. It may or may not work on another port. A week later it could very well lead again on the port that wouldn't work. This applies to all types of devices.

  A few more questions:

  Is there a USB device that you use with all three computers?

  This problem occurs with all kinds of USB devices?

  The is the problem with all the USB ports on each laptop?

  Have you tried to reinstall the USB drivers? As in, uninstall via the Device Manager, restart your PC and allowing Windows to reinstall?

• Having the problem with the function on SG300 Dhcp / 500?

  Having the problem with the function on SG300 Dhcp / 500? now I can use the dhcp server on the two model, but have a problem.

  My problem is when I create

  VLAN 1: 192.168.0.1/24 dhcp pool 192.168.0.10 - 250

  VLAN 10: 192.168.10.10 - 250 192.168.10.1/24 dhcp pool

  case 1

  I plug the pc to vlan 1 can I get ip 192.168.0.11. But when I change this pc to a new port in vlan 2 I always get the same ip address. why I can not get IP of vlan2.

  case 1

  I plug the pc to vlan 2 I can get ip 192.168.10.11. But when I change this pc to a new port in the vlan 1 I always get the same ip address. why I can not get IP of vlan1.

  but when I have access to the switch and remove the link after that that i will get correct IP.

  I think this is the bug of this firmware. Could you help this case.

  This is a known bug that is the setting of Cisco

  Sent by Cisco Support technique iPad App

• Problems with the Display Mode target on end 2009 27 "iMac

  Used late 2009 iMac 27 "in the view target in conjunction with a Dell XPS tower with i7 processor, Windows 7 and the best graphics card I could afford at the time connected by HDMI to mini display port cable.  Worked well for years.  Set aside Dell for a few months and the update of the iMac to El Capitan OS 10.11.3.  Recently tried old setup with same Dell PC and was able to move from Mac to PC, but the PC screen resolution was at the lowest setting. I got an error message when enabling/disabling to PC who said there was a problem with the port causing mini display of the system back to the lowest resolution. Impossible to reset at a higher resolution.

  I tested the Dell PC on another monitor, and it works very well at higher resolution (2560 X 1440). Now, when I reconnected it to the iMac (which works fine), the screen becomes black.

  Is it possible that the operating system upgraded (El Capitan) is not compatible with the targets using mini display port Display Mode?  Any ideas?

  Use your iMac as a display with the target - Apple Support Display Mode , also consider having a bad cable or connection. Does not hurt to try different cables, they can and will the bad!

• Satellite C850 - found problems with the networking and the FN key

  Hey everybody,

  I work on a Satellite Toshiba C850, that my parents recently bought and spin in a certain number of questions.

  (1) wireless won't connect to my network. Have done the following: verified by connecting on two other computers, reset the router, the open network, reset the map, reinstalled the realtek drivers, checked the settings in the networking of Toshiba Utilities. End result is he's going to try, and fail. Wired LAN works fine.

  (2) FN key does not work. Have you checked the region and it is OK, have tried to use the Flash cards - no change, checked with the screen keyboard and can check the FN key does not register.

  I noticed that the first problem is common, but there are obvious positive results. If anyone can offer any assistance, I would appreciate it a lot.

  Before you begin to discuss your problems can you please tell us what OS you are using?
  Are you using the original OS that you got with your laptop? I mean original recovery image has been tested and works correctly, with the factory settings that all should especially the FN keys.

  1 / What do you mean with refusing? your WLAN is visible for your laptop?

  2 / if there is problem with the feature keys FN and you use Win7 try please reinstall extra package from Toshiba.

• Starting problem with the gray screen on iMac

  Hello everyone

  I'm a bit puzzled with a problem I'm having with my iMac 27 "a model late 2009, bought in early 2010, I had built at the time with 8 GB ram, 2 TB HD and fastest i7 Quad core processor available at the time.

  I'm running El Capitan, and all wise OS is perfectly up to date.

  The other week, after a systematic restart, I have a gray screen and little else.  Another reboot and everything was "normal", so I did not concern me unduly.

  Today, after that the Mac had been idle for a time during a call, the screen fell asleep as usual (I do not SLEEP the computer itself), but during his return and touch the SPACEBAR and key "ESC", the screen remains black.

  So I made a forced shutdown and restart.

  I get the screen gray and normal startup (no other sounds) chime followed by the apple logo and the startup progress bar.  He gets to halfway through the long, and then instead of bring to the top of the login page, it's just going to a gray screen Uni.

  So I restarted in safe mode, OK and ran disk utility a couple of times - at the first crossing, he noted, there a problem with the map of partition which can cause problems starting, but on the second passes and the following, everything has been noted to be OK - and the SMART status of disk has been verified.

  After a reboot - the same question as above - of carillon, gray screen with the apple logo, progress bar and then just a gray screen.  I did another secure boot and re-run of disk utility, rebooted into recovery mode and run disk utility.  And again, no problems reported.

  Another reboot and the issue was always there.

  So this time I rebooted into recovery again mode and downloaded a new installation of El Capitan.

  Unfortunately, there is no set - it is always start on a gray screen after the startup chime, the apple logo and progress bar.

  I have also removed all my account account startup items and disconnected all USB devices.

  I'm a bit lost for what to do next to be honest!

  Is there anything else I can do software wise, at home, or is it time for the repair material re shop perhaps?

  Thank you very much for your words of wisdom and support

  Kind regards

  John... :-)

  John here again: :-)

  Just a quick update which may help to determine what the problem is: I restarted in safe mode, after the reinstallation of the operating system was unable to initialize properly - grey screen again.

  However, as I have a home network, I found that I can not connect on the network with my MacBook Pro to the iMac, see all my files user on the iMac and even copy them across to the MacBook Pro with no problems.

  Everything on the iMac is saved via Time Machine on a Western Digital Firewire HD 3to.

  I also have uncompressed manual 'straight' copies of my music, movies, documents folders, etc, for an old time Capsule, currently acting as a bridge to my ethernet network wireless, and provide additional backup for those critical files - my music for example is ripped 350 odd CD, all legally purchased in ALAC on iTunes on the iMac - which represents a couple of months of work... lol... no way I want to lose that!

  So I'm a bit of a loss.  Disk utility reported no problem with the drive... I can boot into safe mode and recovery, but normal mode 'mode '... I always get the chime, the screen with apple logo and progress of the gray bar, then goes to just a gray screen instead of the login page.

  Help!

  My beloved Einstein had a hiccup!

  All comments appreciated and thanks again - hope this extra info helps

  Kind regards

  John... :-)