Problem with the VLAN routing

Similar Questions

• SWITCH Cisco/Linksys SLM224G: Problem with the VLAN

  Hello!

  I'm trying to set up a VLAN in my baskets. I have some knowledge about VLANs, but I still can not configure in my path.

  My situation:

  I have PC that contains two virtual machines, which works as a router between three networks: LAN, WAN, LAN2. It's a bit complicated, but I'll try to draw:

                                                   |-------------||----------------------------|                   |           e1|-to-eth1-VM2-----WAN|VirtualMachine 1        eth0|---trunk-VLAN1&2---|g1         e2|-to-eth0-VM2-----LAN2|eth0=VLAN1 eth1=VLAN2       |                   |           e3|-to-eth0-VM2-----LAN2 etc.|                         PC |                   |   SWITCH  e4||VirtualMachine 2            |                   |           e5|-to-eth1-VM1---wire-to-LAN2|eth0=VLAN3 eth1=VLAN4   eth1|---trunk-VLAN3&4---|g2         e6|-to-eth0-VM1-----LAN1|----------------------------|                   |           e7|-to-eth0-VM1-----LAN1 etc.                                                 |-------------|
  
  gX = Gigabit portseX = 100Mbit portsVMX = Virtual machine numberwire-to = patch-cord connection between ports on the switch
  
  Schema of routing and logical visibility:
  
  LAN1---VM1-----VM2---WAN              |LAN2----------|
  

  Important note is that LAN1 and LAN2 must be separated (visible only through routers). WAN must be visible through VM2 to LAN2 and through by VM1 and VM2 to LAN1. It seems easy, but VLAN that I did on this passage seems doesn't work.

  I do it like this:

  Step 1: Management of VLANS / create a VLAN...

  Creation of VLANS 1, 2, 3, 4 (numbers meters right now - I have now this number 1 is restricted to the switch).

  Step 2: Management of VLAN / Port to VLAN...

  Setting up VLAN1 with ports g1, e5 (the two labelled or not identified?-I have not seen any difference)

  Implementation VLAN2 with ports g1, e6, e7, etc...

  Implementation VLAN3 with ports g2, e2, e3, etc...

  Setting up VLAN4 with g2, e1 ports

  Step 3: Management of VLAN / Port setting...

  Implementation of ports e1 to PVID4 (chassis type = all I guess, but with "capture filter"?)

  Setting up port e2 at PVID3

  Setting up port PVID3 e3

  etc...

  Setting up port e5 for PVID1

  Setting up port e6 at PVID2

  Setting up port e7 for PVID2

  etc...

  Thus, on this configuration and that the switch it does not work for me

  I know that the switch is to see Mac since VLAN which is carried out by PC, because when I arrive in "Admin / dynamic address" I see pimps on the correct ports, with good VLAN ID. So the problem is to transmit a VLAN for their ports, then clear frames of ID and let the packets to go (and return: clear packages, add the VLAN ID and send to their Gigabit ports).

  Show the configuration is one of the many I tried :/ but I think this one is the best.

  Or maybe I don't know VLAN as I think and this scheme is impossible? Please tell me.

  Concerning

  and waiting for any suggestions,

  READ

  Hello.

  These products are processed by the Cisco Small Business Support Community.

  * If my post answered your question, please mark it as "acceptable Solution".

  * Do not forget to give a 'congratulations '. Thank you!

• 2910al - 48G Switch: problem with the VLAN

  Hi all,

  I write a new message because I don't know what is happening on my SW series 2910al - 48G and v1910 - 48G.

  I put on the main core SW VLAN 610 and I put to this VLAN IP addreess 100.110.10.1 24-bit etc and it worked fine until yesterday. I change only PLEASE and I enebale STP - loop protect for ports in the range 1-52. (now I rolback this settings as was before)

  

  STP configuration

  

  Now, every PC that has for a long time what IP range 100.110.10.1 24-bit works fine, but new PC have problem with to get the new IP address. I tested it add a static and same address does not work.

  Introduced in second v1910 SW - 48 G VLAN as below

  I connect this flexible switch this \port SW 2910 - G 48, 46 (Vlan 610 tag) <>- at v1910-48G\ port 50 SW (Vlan 610 tahgged) other ports on this switch I put not marked.

  Configuration file for sw v1910 - 48G looks to below:

  #
  activate default domain system
  #
  LLDP enable

  #
  domain system
  disable the access limit
  Active state
  Disable Idle-cut
  self-service-url disable

  #
  rstp STP mode
  enable STP
  #
  NULL0 interface
  #
  GigabitEthernet1/0/1 interface
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/2
  access port vlan 610
  #
  interface GigabitEthernet1/0/3
  access port vlan 610
  #
  interface GigabitEthernet1/0/4
  access port vlan 610
  #
  interface GigabitEthernet1/0/5
  access port vlan 610
  #
  interface GigabitEthernet1/0/6
  access port vlan 610
  #
  interface GigabitEthernet1/0/7
  access port vlan 610
  #
  interface GigabitEthernet1/0/8
  access port vlan 610
  #
  interface GigabitEthernet1/0/9
  access port vlan 610
  #
  interface GigabitEthernet1/0/10
  access port vlan 610
  #

  #
  interface GigabitEthernet1/0/49
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/50
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/51
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/52
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1

  etc...

  Could you help me when I made a mistake?

  THX

  The problem was that solve this problem.

  I have blocked all ports. It was a problem. I change several settings and everything works well.

• Help with the VLAN routing

  I'm pretty green when I just went and routing configurations please bear with me.  I'm available what I want to achieve and what I could do until now (although it may be completely wrong).

  I have an office where we run low on IP addresses for our local network, the obvious answer is to get VOIP phones on their own subnet.  So, I have a switch PC6224 I want to use to create the second subnet.

  Existing Workstation LAN = 172.22.144.0 (255.255.255.0)

  Default GW for the LAN = 172.22.144.1 for all devices on that subnet

  I would like to create an IPPhone = 172.22.145.0 (255.255.255.0) subnet

  Here's what I have "Achieved" so far:

  Currently, I can ping from a client on 172.22.145.x to the 172.22.144.12 (VLAN 3 ip interface) but cannot ping any other 172.22.144.x that is not directly connected to the 6224 switch device.  Trying to ping the network 172.22.145.x device leave a device plugged into the 172.22.144.x VLAN on the switch of packets results was sent to the default gateway for the network (172.22.144.1) who does not know what to do with them.

  Here is my config of 6224 switch operation:

  Console execution #show
  ! Current configuration:
  ! Description of the system "PowerConnect 6224, 3.3.6.4, VxWorks 6.5.
  ! 3.3.6.4 system software version
  ! Passage mode is configured as disabled
  !
  Configure
  database of VLAN
  VLAN 2-3
  VLAN 2 1 routing
  VLAN 3 2 routing
  subnet of VLAN association 172.22.144.0 255.255.255.0 3
  subnet of VLAN association 172.22.145.0 255.255.255.0 2
  output
  battery
  1 1 member
  output
  IP address no
  IP routing
  IP route 0.0.0.0 0.0.0.0 172.22.144.1
  interface vlan 2
  name "IPPhone.
  Routing
  IP 172.22.145.1 255.255.255.0
  output
  interface vlan 3
  name "TWLAN".
  Routing
  IP 172.22.144.12 255.255.255.0
  output
  level of 746f7a78621059d80fdc538acc40cbf2 user name 'admin' password encrypted 15
  !
  interface ethernet 1/g3
  switchport access vlan 3
  output
  !
  interface ethernet 1/g4
  switchport access vlan 3
  output
  !
  interface ethernet 1/g5
  switchport access vlan 2
  output

  !
  interface ethernet 1/g6
  switchport access vlan 2
  output
  !
  interface ethernet 1/g7
  switchport access vlan 2
  output
  !
  interface ethernet 1/g8
  switchport access vlan 2
  output
  !
  interface ethernet 1/g9
  switchport access vlan 2
  output
  !
  interface ethernet 1/g10
  switchport access vlan 2
  output
  !

  interface ethernet 1/g11
  switchport access vlan 2
  output
  !
  interface ethernet 1/g12
  switchport access vlan 2
  output
  !
  interface ethernet 1/g13
  switchport access vlan 2
  output
  !
  interface ethernet 1/g14
  switchport access vlan 2
  output
  !
  interface ethernet 1/g15
  switchport access vlan 2
  output
  !
  interface ethernet 1/g16

  switchport access vlan 2
  output
  !
  interface ethernet 1/g17
  switchport access vlan 2
  output
  !
  interface ethernet 1/g18
  switchport access vlan 2
  output
  !
  interface ethernet 1/g19
  switchport access vlan 2
  output
  !
  interface ethernet 1/g20
  switchport access vlan 2
  output
  !
  interface ethernet 1/g21
  switchport access vlan 2

  output
  !
  interface ethernet 1/g22
  switchport access vlan 2
  output
  !
  interface ethernet 1/g23
  switchport access vlan 2
  output
  !
  interface ethernet 1/g24
  switchport access vlan 2
  output
  output

  Console #.

  Any help would be greatly appreciated.

  Thanks, Grant

  What port connects to 172.22.144.1 the jump according to the internet?

  What should happen is we need a VLAN 'remote' separate just for the connection between the 6224 and your 172.22.144.1 jump following the internet device.

  If 172.22.144.1 remains the same, then you must create another local network VIRTUAL to "TWLAN".  Eventually, VLAN 4 with a range of ip addresses of 172.22.146.1 - 254 255.255.255.0.  Where the VLAN 4 interface has an IP address defined as 172.22.146.1.  Once that all connected devices again VLAN 4 that were in the VLAN 3 need to change there IPs and gateway 172.22.146.1

  So the only port that has configuration of VLAN 3 is the connection to 172.22.144.1 port next to the internet break.  The IP address defined on the interface VLAN 3 should be in the same subnet as 172.22.144.1 range.

  Here is a diagram that can help you to see the whole upward.  VLAN 100 in the diagram represent VLAN 3 in your case.  Switch 2 would represent your device from the internet of next hop.

  

• problems with the internet connectivity and card # 2 microsoft tun miniport

  Hi, I have problems to connect to the internet and my laptop tells me them a problem with the modem / router. However, another laptop computer connected to the modem/router even works very well. in the Device Manager was an exclamation mark beside "teredo tunneling pseudo interface 10. then it disappeared and I found myself with an error with «#2 microsoft Tun miniport map» now his party in error teredo. I still only have a local internet connection i.e. no internet. not really have a lot of knowledge when it comes to computers. any help would be really appreciated.

  Hello

  You can try the steps in the similar thread to the next with a possible fix:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/Teredo-tunneling-pseudo-interface-this-device/757db042-c91e-464c-B963-c1f442fdf925?page=1

• Could get a new router block printing? We had a lot of problems with the computer in the last week and a half. Bought new router and now the printer does not print. :-(

  (1) we went to DirecTV. Then the same day, our internet computer is down. I asked our current provider, Suddenlink, to let them know we had them to another - but we wanted to keep for the internet.

  (2) called DirecTV to investigate why our internet went down at the same time they installed? They said that they did nothing to cause that. We waited 5 days to make out and also install the third TV that was promised. The second tech gave things a lookover and said, once again, that there is nothing unusual during their passage to cause the problem.

  (3) called Suddenlink. They said it was the router. Called the people of Netgear. They said that the router was too old. We needed to pay an exorbitant sum for support and when I told him I'd rather just buy a new router and get free technical support for 90 days... and I personally do not have the credit cards in that time. (it's my mother s equip and I wonder it for the computer) when the guy told me that he could help and hung up on us, even though I was pleading for him to wait until I put my mother on the phone. (I'm in my 40s... not a kid).

  (4) Suddenlink called a few days later, when we got a new router (netgear brand NO!) Installed and I noticed that the 'ready' light was not 'on' on the modem. Their technology has said that he would check and call us in a few minutes. He did not.

  (5) the next day I called Suddenlink AGAIN. This time, I got a really nice customer service agent. She said she would send someone to check on it. It turns out that they had disconnected when I had called to pass only the TV.

  (6) in any case, we are finally online... only now... I can't the printer to work. :-(  This has worked before.  Could it be caused by the different router? I don't know about these things. I didn't even know what it was until someone at Radio Shack has explained to me. (I was not about to buy one at Wal-Mart - these poor people). The printer is a Canon Pixma MX340. We love him. The only thing is that it is difficult to clear the tasks or to reset. The only way to really do that is to simply pull the plug, unfortunately and restart the computer. But hey, it's a great printer, better than HP.

  We are under vista. The router is a Linksys wifi (which we have) N300 model E900.

  Of course I appreciate any help you can give. God bless you!

  Michelle and Ruth.

  Hello

  Thanks for posting in the Microsoft Community.

  I understand that you are facing problems with the printer in Windows Vista.

  I imagine the inconvenience that you are experiencing. I will definitely help you with this.

  Please follow the steps in the link.

  Solve printer problems

  http://Windows.Microsoft.com/en-in/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

• Connectivity problem - problem with the modem or the router of network

  I had a network with 2 computers.  The main computer was a Windows XP operating system and the secondary is a Windows Vista operating system.  There was a modem connection and the router. Due to a storm and a leak in my ceiling in my main computer got wet and I couldn't use it.  I have connected the modem without the router directly to the secondary computer, but it is not recognize the modem.  "Internet Explorer cannot display the webpage." So I ran the diagnostics and received a message that there could be a problem with the modem or the network router.  I did the thing 'ipconfig' and there is no gateway.  Is there anything I should do to make this secondary computer main computer?

  Hello

  If you use a router there is no primary and secondary, all the computers connected to the router are equal.

  Many Internet service providers allow you to control some form of autehtication (ID, PW) online journal.

  Your router and the computer humid probably were installed to authenticate.

  If the router does not use it.

  Otherwise, contact your ISP and ask for the help of authentication.

  Jack MVP-networking. EZLAN.NET

• Help with the VLAN and RVS4000

  I am trying to Setup VLAN on a RVS4000 to share our Internet connection with another office but do not allow access to our network of the other network. We have a BEFSX41 connected to Internet and also connected to our other site via a virtual private network to another BEFSX41. Port 1 on the BEFSX41 connects to Port 1 on an EZXS88W switch.

  The other company has provided the RVS4000 and also provides a WRT54GS router. I want to connect 2 ports on the BEFSX41 to Port 1 on the RVS4000 and 2 ports on the RVS4000 to track 1 on the WRT54GS.

  Port 1 on the RVS4000 is member of the default VLAN1 and Port 2 will be a member of VLAN2.

  Our IP network is 192.168.20.0/24

  BEFSX41 is 192.168.20.1

  The DHCP service is disabled

  The RVS4000 has a static IP address of 192.168.20.254 and is configured as a router

  DHCP is also disabled

  The wireless network is as follows:

  IP network is 192.168.21.0/24

  The address IP of WRT54GS is 192.168.21.254 and is static and also configured as a router.

  I don't know how to actually Setup the VLAN from here and the instructions are not useful. My questions are:

  1 port 1 on the RVS4000 must be safe, with label or Untagged?

  2 If the interval routing disabled?

  3. If so, how do I route between the RVS4000 and WRIGHT so the two networks have access to the Internet, but not to other networks?

  The befsx41 should be one that is connected to the internet so that your final point so that the vpn tunnel work. The wan port on the wrt54g must be connected to the lan of the befsx41 port.

  If your server is located behind the befsx41, you should be able to port forwarding. If your server is located behind the wrt54g you may experience the problem with the redirect because you need to forward ports on both routers and according to me, there are some applications that do not work on double NAT.

  If you want to have access to the internet on both VLAN of the rvs4000, it should work as a router so its internet port must be connected to the port the befsx41 lan.

• Problems with the network controller

  Hi, I have a problem with the driver for network controller. I mean my wireless does not work... it connects to the router, but it still has this yellow warning and will not connect to internet. I tried everything and it doesn't work. I have not found a pilot wireless on the hp site. I have a HP laptop model 15-r020sq.

  Hi, I used the driver that you post. Now I have the same problems as before. I went over the details of the driver it's what he know upstairs: PCI\VEN_1814 & DEV_3290 & SUBSYS_18EC103C & REV_00

• Satellite C850 - found problems with the networking and the FN key

  Hey everybody,

  I work on a Satellite Toshiba C850, that my parents recently bought and spin in a certain number of questions.

  (1) wireless won't connect to my network. Have done the following: verified by connecting on two other computers, reset the router, the open network, reset the map, reinstalled the realtek drivers, checked the settings in the networking of Toshiba Utilities. End result is he's going to try, and fail. Wired LAN works fine.

  (2) FN key does not work. Have you checked the region and it is OK, have tried to use the Flash cards - no change, checked with the screen keyboard and can check the FN key does not register.

  I noticed that the first problem is common, but there are obvious positive results. If anyone can offer any assistance, I would appreciate it a lot.

  Before you begin to discuss your problems can you please tell us what OS you are using?
  Are you using the original OS that you got with your laptop? I mean original recovery image has been tested and works correctly, with the factory settings that all should especially the FN keys.

  1 / What do you mean with refusing? your WLAN is visible for your laptop?

  2 / if there is problem with the feature keys FN and you use Win7 try please reinstall extra package from Toshiba.

• ProBook 450 G0: The problem with the ralink ralink RT3290 адаптер чипсет с Проблема RT3290 adapter

  The connection on the router TP - LINK Archer C2 problem. On the previous version of the driver for wi - fi doesn't appear, although it is (checked on the phone and tablet) but wifi on all other routers sees it. Installed version of the pilot on June 18, 2015 5.0.57.0. Screenshots of Wi - fi. But another problem appears: could not connect to Wi - Fi. Gives this error 'Windows cannot connect to the network' or 'connect without access to the Internet. Using manual reconnection to the network or restart the laptop. We're spontaneous deactivation of a Wi - Fi connection, even if the Wi - Fi network works correctly (currently, a Tablet and a work of smart phones over wi - fi). And poor quality. Even being near the place of distribution, there are problems with the wireless network. Another question is why the laptop is not catch wifi 5 GHz (on configured router)?

  Проблема соединения по роутером с Archer C2 TP-LINK wireless. На предыдущей версии драйвера соединение по wi - fi не видит, хотя оно есть (проверял на смартфонах и планшете), но wi - fi от других роутеров видит.Установил itself версии 5.0.57.0 от 18 июн 2015. A WiFi ловит. Но возникает другая проблема: не удается подключиться Wi - Fi Интернет к. Дает такую ошибку "Windows не подключиться сети к удается" или "Подключение без доступа к интернету". ПОМОГАЕТ ТОЛЬКО РУЧНОЕ ПЕРЕПОДКЛЮЧЕНИЕ К СЕТИ ИЛИ ПЕРЕЗАГРУЗКИ ЛАПТОПА. Есть спонтанное отключение сети Wi - Fi, хотя в Wi - Fi сеть работает нормально (в это планшет и смартфоны работают от wi - fi время). И КАЧЕСТВО СВЯЗИ ПЛОХОЕ. БУДУЧИ ДАЖЕ РЯДОМ ПО МЕСТУ РАСПРЕДЕЛЕНИЯ СУЩЕСТВУЮТ ПРОБЛЕМЫ n БЕСПРОВОДНОЙ СЕТЬЮ. Еще вопрос почему лаптоп не ловит wi - fi на частоте 5 ггц (на все настроенно роутере)?

  You can install MediaTek (Ralink) 802.11 b/g/n wireless LAN adapt driver

  Rev.D version 5.0.56.0 (June 10, 2015)

  -Fixes an issue where the system does not correctly connect to a wireless access point and the wireless network connection is limited.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_149767_1

  I think that RT3290 is a 2.4 GHz wireless module

  You can turn off Bluetooth in the BIOS for wireless performance batteries.

• Problems with the internet connection, Aspire V15 - V3 - 575G

  Hi, I bought a new laptop and have problems with the internet connection without having to install other programs.

  The problems are the following:

  • I use an ethernet cable to connect and just after passing on the laptop, there is no Internet connection at all. I have to restart the router to do.
  • When downloading or uploading brokes down at intervals of 30 seconds - 1 minute. It is not always the same. Sometimes it works 3 minutes, but it is not enough.

  He has Win10... With my old laptop with Win7, I had no such problems. I do not change ISP.

  I don't know what to do to fix it. I have not tried to uninstall Acer applications yet. Have you experienced something similar?

  Thank you very much for the reply.

  Plese try this:

  device, right-click on your network card Realtek Manager choose uninstall and tick to uninstall the software if requested, restart, and then try again to install the downloaded driver.

• having problems with the pop-up windows of analytical Google all of a sudden and now the pages are crashing or being redirected

  original title: google analytics popups

  Ive been having problems with the Google analytic pop-up windows all of a sudden now pages break or redirected, I've ran Malware, Windows Defender, a direct care, Avira, Avast and F-secure, and nothing seems to have read on other forums to help, that his may be a Trojan horse: Trojan.osx.Dnschanger.B... ive also rebooted my router as suggested in some forums , but nothing seems to help?

  Hi NicolaaTC,

  See the links below and check if it works.

  What is the browser hijacking?

  http://www.Microsoft.com/protect/terms/hijacking.aspx

   

  Difficulty of your web browser hijacked

  http://www.Microsoft.com/security/spyware/browserhijacking.aspx

• Problems with the IP settings on XP pc wireless network

  I have (part time) a wireless network to recently set up. Router is connected to a pc windows 7, and there is a XP machine with a USB adapter as well. The PCs are turned on, and the XP shows a wireless connection with a 'very good' signal. When I try to start IE on XP it will fail to connect. When I then run the diagnostic network connection died at around the point where the diagnosis is trying to reactivate the adapter. The diagnosis of output reports "error renew IP address: semaphore timeout has expired" and "default gateway 0.0.0.0." If I then run ipconfig/all there is absolutely NO output. This happened yesterday, so I manually reset following IP 299357 instructions and the same thing happened again. I did the reset again and rebooted the XP. The router indicates that it has recognized the XP and ipconfig/all on XP shows things different, including

  IP 192.168.2.6. subnet mask 255.255.255.0; gateway by default, dns server, and dhcp like 192.168.2.3 Server (the IP address of the router); DHCP and automatic configuration enabled. IP routing and WINS proxy are disabled.

  While I was typing the above router lost sight the XP box, although the box XP still reports a 'very good' signal and a connection permanent.

  So far, I had this network in place for 10 days, but could not use the connection to the outside of the PC XP on a day, which followed my re - configure the router to its IP address 192.168.2.3 rather than recommended in setting up such 192.168.2.1, because 192.168.2.3 was that the XP box trying to connect as. Two PCs have been turned off during the night and worked fine when started the next morning for the entire day. The next day that XP had a connection for long enough to reach the site where I was looking for updated printer drivers, and then he lost when I started to download the and nothing since. IP information now suggests that I might have little joy for a while, if I still have to reset the IP address of the router to 192.168.2.6 this time, but I don't see why I should continue to do.

  Some of the other TCP performer? Troubleshooting IP connectivity:

  Ping 127.0.0.1 return OK; ping 192.168.2.3 expires; ping 192.168.2.6 is OK; ping host name does not work (assuming that the host name is just the name of the computer to the pc win 7); Pathping 192.168.2.6 works. (If that this watch is actually the host name and then ping that name does not work either, there is no entry in the ARP cache, do not know the valid IP addresses to test those.)

  Suggests that I have problems with the default gateway, and name resolution, but I do not know how to set resolution, unless you change the IP address of the router, which can do the first, but not the second.

  Suggestions welcome.

  The fact that things worked fine for a day seems to indicate that the material is OK, and I checked that I have the latest firmware for the router and USB adapter. Security of the router is disabled, as is the firewall on the XP, neither of which is ideal

  Technical support of Belikin has decided that the adapter was flakey too and should be replaced. If we call things the customer support, and I heard of them since, did not except a s message that seemed to ask whether or not I had entered with them...

  So what network?

  Packed wireless router and got some kit devolo for a network of current carrier online (on the grid) put in place instead. More expensive, Yes, but IT WORKS! 6 weeks later, still no problem to access Internet from a PC.

• Wireless camera does not work with the new router

  Hello, I'm having a problem with a camera D-Link DCS932L after you set up the EA4500.  The manual of the camera can be found here.

  http://d2okd4tdjucp2n.CloudFront.NET/DCs-932L_A1_Manual_v1.00 (NA) - en.PDF

  It worked fine with my old D-Link router.  The rest of the House has not had a problem with the EA4500.  There is a level of criticality around this camera certail and if I can't make it work, I'll have to return the router.  Configure the redirection of port as 5556 ~ 5559, TCP protocol (but I tried "Both" as well"with the IP address of the camera.  It still does not work.

  I craft but not in networks, i.e. I'm not stupid with tech but port quarrels is out of my comfort zone.  This camera with our old router setup took minutes.  I spent five hours trying to make it work on the EA4500.

  I guess you have the static IP value, or having a reserve of DHCP MAC address for the camera, network OK settings.

  What was the authentication wireless on the old router and that you use the new 4200?

  Is it possible that the camera does not support the encryption used by the 4200, i.e. wpa2-personal?

  Have you tried WEP to see if the unit works then?