problem with TSSTcorp cddvdw sh-s223c drivers
My dvd device has stopped working altogether. I get the error "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) "but when I try to update it tells me that windows has determined the driver software is up to date.
I uninstalled, reinstalled etc but no joy.
It was fine before... nothing has changed as far as I am aware, no major updates, installs or downloads.
Help!
Hello
Method 1: I'd say you run the fixit provided in the link and check if this can help:
http://support.Microsoft.com/kb/982116
Method 2: run the fixit for the link if the problem persists after you run the fixit above:
http://support.Microsoft.com/mats/hardware_device_problems/en-us
Method 3: you can also run the fixit from the link:
http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us
Tags: Windows
Similar Questions
-
After the last updates of windows have problems with start up and now drivers
Hello
After the last updates of windows have problems with start up and now drivers. I get an error code 21 when I try to install the drivers AMD apparently missing.
May 14, last night I had several (automatically) downloaded windows update
Today, I was unable to boot my computer with Windows - tried the disk check, start checks etc, and eventually had to use System Restore (for help before the critical update to restore).
Perfection, everything works, but knowing that windows will attempt to redo an automatic update, tried to check online - no one seemed to have a problem and (naivly) thinking I could always do another restore of the system, I rebooted again.
Same thing worse. Could not do a sys restore either just before restarting or last night. Chose a date earlier (last week) but then lost the USB drivers and pilots display. Downloaded updated but refuses to let my AMD driver install Windows I have a very unpleasant screen... and I must now stop the installation of this update "critical."
Would appreciate advice how do my installed display driver or whether anyone else has problems following this update
Thank you
Hi Jane,
You have a disk to install Windows 7 with you?
I suggest you to check the event viewer for error details report.
Open event viewer.
http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer
-
Problem with TSSTcorp TS-L632D TO04 CD/DVGW stoped burning CD and DVD
Hello world! The problem is basically just, he doesn't want to write/burn any cd/dvd brand more. He works wonders for little over a year and recently developed this problem. I'm sure that's not media brands I've tried with several. The problem with Nero, Alcohol120%, MagicISO, PowerISO, Burn4Free, regardless of what I am trying to burn data, audio, regular programs or images. Note that I am able to write with alcohol with success but there is in fact nothing on the CD and Nero burns the data also but fails to verify after the fact and gives an error. Writing on DVD R/RW is completely failed, creating coasters. Also the Player opens without reason and when he wants. I have laptop Toshiba A200 - 1 MB under original Vista Home Premium. Here's an error report, hopefully it'll help. Thanks and any assistance is much appreciated!
Windows Vista 6.0
IA32
WinAspi: -.NT-SPTI used
Nero Version: 9.2.6.100
Internal Version: 9, 2, 6, 100
(Nero Express)
Recorder:Version: TO04 - HA 1 YOUR 0 - 9.2.6.100
Adapter driver:HA 1
Drive buffer: 2048kB
Bus type: Via inquiry data
CD-ROM:Version: TO04 - HA 1 YOUR 0 - 9.2.6.100
Adapter driver:HA 1 = Scsi-device-map =.
= CDRom-Device-map =.
TSSTcorp CD/DVGW TS-L632D E: CdRom0
=======================AutoRun: 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) bytes
BUFE: 0
Physical memory: 2037 MB (2086276 KB)
Free physical memory: 864 MB (885052kB)
Memory used: 57%
QUERIES PFiles: 0x0
Global Bus type: default (0)
Control supported media: disabled (0)13.10.2009
CD-ROM (ISO)
02:27 A. Â? ? Â? #1 text 0 file SCSIPTICommands.cpp, line 452
LockMCN - completed successfully for IOCTL_STORAGE_MCN_CONTROL02:27 A. Â? ? Â? #2 text 0 file Isodoc.cpp, line 6940
ISO document burn settings
------------------------------------------
Determine maximum speed: TRUE
Simulate: FALSE
Write: TRUE
Finalize the CD: FAKE
Multisession: TRUE
Multisession type: Start multisession
Burning mode: TAO
Mode : 1
ISO level: 1 (Max. of 11 = 8 + 3 char)
Character set: ISO 9660
Joliet: TRUE
Allow pathdepth more than 8 directories: TRUE
Allow more than 255 characters in path: TRUE
Write ISO9660; 1 file extensions: TRUE02:27 A. Â? ? Â? #3 text 0 file Burncd.cpp, line 3257
TSSTcorp TS-L632D CD/DVGW
Super link activated02:27 A. Â? ? Â? #4 ISO9660GEN-11 file Geniso.cpp, line 3349
First address writeable = 0 (0x00000000)02:27 A. Â? ? Â? #5 text 0 file ThreadedTransferInterface.cpp, line 1017
Removed 2 blocks from end of track 0. Length: 2885-> 2883.02:27 A. Â? ? Â? #6 text 0 file Burncd.cpp, line 3587
Turn on Track-At-Once, using CD-R/RW media02:27 A. Â? ? Â? #7 text 0 file ThreadedTransferInterface.cpp, line 1017
Removed 2 blocks from end of track 1. Length: 2885-> 2883.02:27 A. Â? ? Â? #8 text 0 file ThreadedTransferInterface.cpp, line 1017
Removed 2 blocks from end of track 1. Length: 2885-> 2883.02:27 A. Â? ? Â? #9 text 0 File DlgWaitCD.cpp, line 294
Media in the drive type: unknown
Write speed more up/down CLV: 3 x / 1219560 x
Recorder min/max supported write speed: 4 x / 9226724 x02:27 A. Â? ? Â? #10 text 0 File DlgWaitCD.cpp, line 313
Last possible write address on media: 359846
Last address to be written: 288402:27 A. Â? ? Â? #11 text 0 File DlgWaitCD.cpp, line 325
Write in overburning mode: No. (enabled: CD)02:27 A. Â? ? Â? #12 text 0 File DlgWaitCD.cpp, line 2882
Recorder: TSSTcorp TS-L632D CD/DVGW;
Code CD - RW: 00 97 10 00; CD manufacturer unknown
ATIP data:
Special Info [hex] 1: D1 00 C6, 2: 61 a 0, 00 (LI 97:10.00), 3: 4F 3 b 4 a (LO 79:59.74)
Additional info [hex] 01:02 4A B0, 2:5 C6 26, 03:00 80 80 (invalid)02:27 A. Â? ? Â? #13 text 0 File DlgWaitCD.cpp, line 500
> Protocol of DlgWaitCD activities:
=========================================02:27 A. Â? ? Â? #14 text 0 file ThreadedTransferInterface.cpp, line 744
CIS (after recorder preparation)
0: TRM_DATA_MODE1)
2 indices, index0 (150) not provided
#0 + 2885 (2885) original disc POS = 2885 # / 0:38.35
relocatable, pos to drive for the cache-write implementation not required / required
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2883 blocks [E: TSSTcorp CD/DVGW TS-L632D]
--------------------------------------------------------------02:27 A. Â? ? Â? #15 text 0 file ThreadedTransferInterface.cpp, line 946
Prepare [E: TSSTcorp CD/DVGW TS-L632D] for write in TAO
DAO infos:
==========
MCN:
TOCType: 0x00; Closed disc, session not obsessed
Titles 1 to 1: Idx 0 Idx 1 next Trk
1: TRM_DATA_MODE1, 2048/0 x 00, FilePos 0 307200 6215680, ISRC ""
Introduction DAO:
===========
___Start_ | ___Track_ | _Idx_ | _CtrlAdr_ | ___Size_ | ___NWA_ _ | _RecDep___
-150 | Lead-in | 0 | 0x41. 0 | 0 | 0x00
-150 | 1. 0 | 0x41. 0 | 0 | 0x00
0 | 1. 1. 0x41. 2885 | 0 | 0x00
2885 | Lead-out | 1. 0x41. 0 | 0 | 0x0002:27 A. Â? ? Â? #16 text 0 file ThreadedTransferInterface.cpp, line 1017
Removed 2 blocks from end of track 1. Length: 2885-> 2883.02:27 A. Â? ? Â? #17 text 0 file SCSIPTICommands.cpp, line 242
SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME02:27 A. Â? ? Â? #18 text 0 file Burncd.cpp, line 4320
Caching options: cache CDRom or network-Yes, small files-no)<>02:27 A. Â? ? Â? #19 phase 24 file dlgbrnst.cpp, line 1767
Caching of files started02:27 A. Â? ? Â? #20 text 0 file Burncd.cpp, line 4442
Cache writing successful.02:27 A. Â? ? Â? #21 phase 25 file dlgbrnst.cpp, line 1767
Caching of files completed02:27 A. Â? ? Â? #22 phase 28 file dlgbrnst.cpp, line 1767
Speed measurement started02:27 A. Â? ? Â? #23 text 0 file ThreadedTransferInterface.cpp, line 2676
Check position of the point disk 0 (relocatable, disc pos, no patch, orig to #0 info): write to #002:27 A. Â? ? Â? #24 text 0 File ThreadedTransfer.cpp, Line 273
Size of the memory pipe 59040002:27 A. Â? ? Â? #25 phase 29 file dlgbrnst.cpp, line 1716
Speed measurement completed: 307.7 x (46? Â? ? Â * 160 KB/s)02:27 A. Â? ? Â? #26 phase 36 file dlgbrnst.cpp, line 1767
Burn process started at 4 x (600 KB/s)02:27 A. Â? ? Â? #27 text 0 file ThreadedTransferInterface.cpp, line 2676
Check position of the point disk 0 (relocatable, disc pos, no patch, orig to #0 info): write to #002:27 A. Â? ? Â? #28 text 0 file MMC.cpp, line 21875
Set BUFE: Super link-> ON02:27 A. Â? ? Â? #29 text 0 File ThreadedTransfer.cpp, Line 273
Size of the memory pipe 8383680002:27 A. Â? ? Â? #30 text 0 file MMC.cpp, line 17311
Start narrow-gauge #2 02:28 A. Â? ? Â? #31 text 0 file DVDPlusDualLayer.cpp, line 1424
SetDriveCaps: Set LAST LBA of layer 1 to 002:28 A. Â? ? Â? #32 phase 37 file dlgbrnst.cpp, line 1767
Burn process completed successfully at 4 x (600 KB/s)02:28 A. Â? ? Â? #33 phase 78 file dlgbrnst.cpp, line 1767
Data verification started02:28 A. Â? ? Â? #34 text 0 file ThreadedTransferInterface.cpp, line 1017
Removed 2 blocks from end of track 1. Length: 2885-> 2883.02:28 A. Â? ? Â? #35 text 0 File ThreadedTransfer.cpp, Line 273
Size of the memory pipe 59040002:28 A. Â? ? Â? #36 SPTI-1064 file SCSIPassThrough.cpp, line 215
CdRom0: SCSIStatus (x 02) WinError (0) NeroError(-1064)
CDB data: 0 x 28 00 00 00 00 00 00 00 01 00 00 00
Key: 0x05 (KEY_ILLEGAL_REQUEST)
Printing Code: 0x21
Meaning of Qual: 0x00
Sense area: 0 x 70 00 05 00 00 00 00 0 to 00 00 00 00 21
Buffer x0a5a6500: Len x 800.................................................. .................................................. ............
.................................................. .................................................. ............02:28 A. Â? ? Â? #279 SectorVerify 20 file Cdrdrv.cpp, line 11185
Sector 0 to 1055 read errors02:28 A. Â? ? Â? #280 CDR-1222 file Writer.cpp, line 203
Checking abandoned, too many errors
E: TSSTcorp TS-L632D CD/DVGW02:28 A. Â? ? Â? #281 phase 81 file dlgbrnst.cpp, line 1767
Data verification failed02:28 A. Â? ? Â? #282 text 0 file SCSIPTICommands.cpp, line 289
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME02:28 A. Â? ? Â? #283 text 0 file Cdrdrv.cpp, line 11243
DriveLocker: UnLockVolume completed02:28 A. Â? ? Â? #284 text 0 file SCSIPTICommands.cpp, line 452
UnLockMCN - completed successfully for IOCTL_STORAGE_MCN_CONTROLExisting drivers:
Registry keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogonPost edited by: velkoto
Post edited by: velkoto
Try to remove the CD/DVD filters in the registry.
When the associated CD/DVD (such as iTunes, Nero, virtual CD software), the software is installed, they install filters in the registry, which can cause compatibility problems.(1) run Regedit (start-> Run-> Regedit)
2) navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
(3) in the right pane, delete the "UpperFilters" key and delete the key "LowerFilters".
(4) restart.If your CD/DVD programs stop working, you will need to reinstall them (preferably with an updated version).
This utility can remove the filters for you:
http://www.CSD.Toshiba.com/content/support/bulletins/su2065061/RmvFltrs.exeAlso remove the dust on the lens with a clean Microfiber cloth.
-
Problem with the Lenovo Z575 VGA drivers
Hi guys,.
As you probably know, driver VGA for this laptop is a bit outdated. I have a problem with Rage. It crashes after a few minutes of play. I guess that it also works with the only Integrated GPU because there are differences in performance between the modes 'High Performance' and 'Save energy' in the ATI drivers.
So I decided to install the new version of Catalyst 12.6 beta which has full support for mobile and swichable graphics. Alfer, Rage finallny works like a charm - no falls down and inprovement of great performance, but the BONE started to freeze and crash. Also other games began to work more bad. On official catalyst 12.4 site AMD form is identical on 12.6 beta.
And the strangest thing is that my friend has the Asus laptop with the same features of the CPU and GPU, and he has not had problems using the latest drivers form AMD site.
If you have any sugestions how to solve that or what is going on, please help me
OK, I solved the problem. Just had to uninstall Amd accelerated video transcoding device and now all works well on catalyst 12.4 in the site of AMD.
-
Problem with the HP Pavilion tx2000 drivers!
Hi all!
I'm trying to find a solution to my problem for a whole day, now and until now I Don t have nothing!
My problem:
Last week, I installed Windows 7 Profesionall on my laptop and I have a problem with drivers for graphics cards, shortcut keys on fingerprinting and monitor drivers.
I installed win 7 drivers on your page (sp45823) and nothing fundamentally heapened. The most important are graphics drivers for me now. As I said I installed the HP driver pack drivers and also page from Nvidia, but still nothing. When I go to display properties whenever the name of the graphics card graphic VGA Standard.
I would ask you if you could help me how to find the drivers or if you could tell me what to do.
Concerning
Please try to get the driver using Windows Update in Device Manager. This will search for the most appropriate driver.
While I am an employee of HP, I'm not an expert on all our products. When I offer advice, I do not speak for HP.
-
problem with TSSTcorp DVD +-RW Drive SN - 208BB driver
Hi I have a laptop Inspiron Windows 8, only about a month and the DVD continued to show. I put a cd or dvd and shows nothing. He makes noises but doesn't show anything. I ran a material and problem solving devices and it says there is a problem with the above drive and the USB-drive IF port. I select apply this fix, but it says it can't be fixed and the driver must be reinstalled.
Ive tried to find this driver on the dell website, and I can't seem to find it. I think it's a Toshiba product but am really stuck now. Can anyone help? :(
Hmm, well I went into Device Manager, uninstalled and it did something and came back! I tried the same thing with the USB driver, I had trouble with, but who did not return :/ Hmmmm...
-
Problem with D009TU in latest Notebook drivers
Hello
Recently I bought HP 15-d009TU Notebook PC. It came with BACK installed. I installed Windows 7 64-bit OS. I downloaded the drivers listed in the section download drivers & HP.com, but most of these drivers (driver chipset Intel graphics driver, Audio driver, etc.) does not work. While trying to install it, most of them said that it is not liable for the minimum requirements that all system requirements mentioned in the list of requirements are present.
Now, I am unable to use even the USB ports in my laptop.
So please give me as soon as possible to this terrible problem.
Thank you
Nitin
Hello:
Here are the links to the drivers you need except the wireless and bluetooth:
Chip set. First, install and restart.
Graphics card: install second and reboot.
Install the audio driver from third and restart from support page and the driver of your PC.
Install the fourth Realtek LAN driver.
Here is the USB 3.0 driver which you are interested.
For the PCI encryption/decryption controller, you need this driver:
In order for me to post the links for drivers without wireless/bluetooth, do like this...
Go to Device Manager and click on the network controller needing drivers.
Then click on the Details tab at the top of the control of the network window.
Now, you see a drop-down list of property and it is set by default to the Description of the unit.
Drop down on it and select the second item in the list (Hardware ID).
After the first string of characters that start with PCI\VEN.
-
Acer XB270HU ULMB problem with my screen, or maybe drivers? Baffled
Greetings! I bought this XB270HU this month and I love it. It seems that G-Sync works like a charm, and this 144 Hz refresh rate is wonderful. There is some bleed slightly at the top left which can be seen with black bars around some videos, but never in the videos themselves. Considering that it is the only way he can be spotted, I thought I finally found a BIG screen. My old one was a Dell S2440L, who had an exceptional contrast and zero bleeding, but had problems massive overdrive.
While everything happens very, I chose to use ULMB sparingly because it bothered my eyes the first time I tried it, although the screen visibly drive doesn't bother me. For the record, this monitor is the one that supports ULMB at 120 Hz and if you try to activate at 144 Hz, the monitor starts flashing a message saying it cannot be used to 85 100 and 120 Hz. Thus, it * is * working at 120 Hz. I'm sure I can have used experience of nvidia GeForce update graphics drivers at least twice by habit, and Windows Update installed a XB270HU driver as well. Recently, I went to turn on ULMB at 120 Hz for use with a movie and was shocked to see that the screen got * best * instead of gradation. I chose 85 and 100 Hz to see, and it lit up as well, for the same settings. I don't really understand what happened, but it feels as if its not even using ULMB. Since it worked well and all of a sudden is not, is it a driver problem to an update or something go haywire inside the screen? I've never fiddled with something other than the brightness levels. I have the 144 Hz Gsync mode at 50% brightness instead of the 36 percent that I had it before and when I turn ULMB 30% brightness, it seems much brighter than it does now. I find it incredibly strange and hoped someone could we help with that or help me fix.
Some features:
8.1 Windows 64-bit (update to 10 soon)
Intel Core i7 - 3770K @ 4.4 Ghz
ASUS Maximus V formula BIOS 1903
Memory of 16GB (8GBx2) DDR3-2133 G.Skill RipJaws X series
eVGA GeForce GTX 980 Ti SC + ACX 2.0
Using the DisplayPort cable supplied with the monitor yet.
Acheron,
MP received, thank you.
-
I have a problem with the installation of the drivers for the Belkin card.
Hello
I just bought a new Belikin N150 USB Wifi Adapter. I went through the installation disc and all except that tooth was installing the drivers. I tried to install the drivers, and it gave me this error. Help, please! I am also on an Administrater account
~ Matt
Hello Matt,
Thanks for posting your query on Microsoft Community forum.
I would be grateful if you can provide us with the following information to help us better understand the issue.
- You are able to install other software/drivers without any problem?
- You have security software installed on your computer?
Try it out below mentioned methods and check if it helps.
Method 1
I suggest you to disable the temporary security on the system software and check if it helps.
Disable the antivirus
http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attack.
Method 2
Note:
This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
You can use the following link to back up and restore the registry in Windows: http://support.microsoft.com/kb/322756/
This error can occur due to permission problem in the registry for the USB controllers. I recommend that you take the permission to the registry editor USB. To do so follow the steps below.
- Run regedit from the Start menu. Be sure to export a backup copy of the registry before continuing.
- Browse to the location:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\ENUM\USB
- Right click on the USB folder and select permissions...
- In the dialog box, make sure everyone is a listed group and that the reading is checked.
- Click the Advanced tab and make sure that include the permissions that can be inherited from the parent of this object is selected, as shown.
- Go to the owner tab and be sure to replace the owner of subcontainers and objects is selected as shown.
- Select Apply to apply these changes. A warning message may appear at this stage. Select OK to continue.
- If necessary permissions for USB dialog box select , and then click OK to exit.
Feel free to post them here if you need further assistance.
Thank you.
-
Problem with non-plug-and-play drivers.
I need assistance with drivers Non-Plug and Play, Null, for a Windows 7 Professional 32-bit SP1, I find the Question, no answer to the problem. In the Device Manager, on the driver tab: status is stopped and does not start. And on the general tab: device status is: this device is not present... Bonneau, Bonneau, bla (Code 24). someone Pleazzzzzzee help me, lolol
Hello Thomas,.
Welcome to the Microsoft Community Forum.
- Which device you are trying to connect to the computer?
- You did no particular change in the computer?
- A device that has a code 24 in Device Manager?
Code 24 indicates that the device is not present or is not working properly, or does not all its drivers installed.
If the error code reappears, check that the device is properly connected to your computer. For example, remember that all the cables are correctly installed, or that the cards are properly housed in their locations.
See the article: error codes in the Device Manager in Windows
http://support.Microsoft.com/kb/310123/en-us
Also try to update the drivers for the device.
See the article: automatically get recommended drivers and updates for your hardware
Please respond to this answer, we will be happy to help you.
Thank you.
-
Problems with TSSTcorp CDRWDVD TS-H493A
So I tried to burn a CD a few days ago and whenever I tried to start the burning process it told me to insert a blank CD. So I thought maybe that the CD did not work, but it worked fine on my brothers computer. So I found my Dell disk drivers and reinstalled the drivers from there, but that has not changed anything. I also tried to turn the reader, uninstall/reinstall and I also decided to just restore my computer to see if it would work (it didn't). Before I restored the CD player was another fine then he couldn't burn CDs. But after the restoration, it has stopped working completely. He reads is no longer just about any type of disc I put in. So, I tried to find the driver on the site of the manufacturer, as well as Dell website and could not find anything. I can't find much information on this CD as it is. I find the TS - H492has but I can't find anything on the TS - H493A. I also assured in "configuration" that pilots were put on and all that good things, still nothing. Any help with what I can do now?
I forgot to add it's TSSTcorp CDRWDVD TS-H493A, version - D200
Message edited by skippyy on 03/24/2008 13:40
-
problem with the hp 15-g013sw drivers
Please help me, I bought a new HP laptop 15-G013SW free back here in Greece, and I can't find the drivers for the site official hp. can I find the drivers and download somewhere else? Please note that I can't connect to Internet through ethernet or wifi.try with win 7 ultimate x 64 operating system.
Thank you!
Hello:
Download the files on another PC and copy it to a USB or burn it to a DVD. This media to install the drivers on your 15 HP.
First, install the amd chipset drivers and restart. You want the first file on the Web page.
http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2064
Then, install the graphics driver and restart.
http://support.AMD.com/en-us/download/mobile?OS=Windows%207%20-%2064
Audio: Accept the agreement. Download and install the driver for the second on the list.
Ethernet: Download and install the driver for the second on the list.
Card reader: download and install the driver first on the list.
Webcam:
I don't know what model of laptop wireless card is.
Please do the following in order to identify the model of the wireless card and find the driver, he needs...
Go to Device Manager, find the other devices category, click the network controller needing drivers.
Then click on the Details tab at the top of the control of the network window.
Now, you see a drop-down list of property and it is set by default to the Description of the unit.
Drop down on it and select the second item in the list (Hardware ID).
After the first string of characters that start with PCI\VEN.
-
Problems with Plug n Play device drivers
I try to manually install drivers of Plug-and-Play devices for my Aglient 81104 A pulse generator, and I'm having a little difficulty. I found the instructions to know how to manually extract the files, but the instructions say to paste the folder (which contains two files .llb and about 10 files without extensions) to "National Instruments\LabVIEW\instr.lb", but the thing is, I do not have a folder under \LabVIEW\ \instru.llb. All I have is 'MAX' 'NOR-DAQ' and 'shared '. I tried the search function for a folder called instr.lib, but I couldn't find one on the computer. I made a new folder instru.lib and run one of the files .llb, which opened in LabVIEW, manually, but they gave me ten mistakes most read like this
"-VI should happen to '
: \hp81110a\hp81110a.llb\HP81110A Reset.vi' has been charged with"C:\Users\Lab\AppData\Local\Temp\Temp1_hp81110a.zip\hp81110a.llb\HP81110A Reset.vi" I tried to manually navigate to the folder \AppData as to move to the folder where they were expected, but I did not see this .vi when I opeend my user \Lab\ folder.
What happens here?
Thanks in advance!
vweltin wrote:
I try to manually install drivers of Plug-and-Play devices for my Aglient 81104 A pulse generator, and I'm having a little difficulty. I found the instructions to know how to manually extract the files, but the instructions say to paste the folder (which contains two files .llb and about 10 files without extensions) to "National Instruments\LabVIEW\instr.lb", but the thing is, I do not have a folder under \LabVIEW\ \instru.llb. All I have is 'MAX' 'NOR-DAQ' and 'shared '.
Your operating system is windows, no?
You search under
\Program Files\National Instruments\LabVEW (version)? Apparently not that you are looking in the right folder of LabVIEW. You should see:
applibs
self-test
CCodeGen
cintools
Database
examples
Help
InStr.lib
Internet
... and so on...
-
Problem with update display Pavilion dv6 drivers - 3023ca
Hello
I am not well eaten English so I do short...
I have this type of laptop: HP Pavilion dv6 - 3023ca Entertainment Notebook PC
I just installed a new version of windows 7 Home premium x 86
When I tried to install my display drivers her did not work at all
I had these problems as:
- I can't play all video files by KMPlayer (or any similar programs)
- Job of dosen't effect Aero (trouobleshooter said that it is because of my type of graphics card or driver)
- I can't use the option of sleep to the start menu
Here is a picture of Deviece maneger:
If the drivers must be installed correctly
But it still does not work
I downloaded all drivers (I used the site AMD official and even here I have even updated their Windows) but still I got the problem
So I used HP Support Assistant to troubleshoot and test my card graph (or display)
(Home > troubleshooting > graphics, video and display > video check HP)
It took just a minute to give me this error:
Test Result: Fail Failure ID: UC462J-56C6NU-PXG03G-Q0NX03 HP Graphics Video Check detected an issue while running. The directx SetCooperativeLevel function has failed. Graphics card may be defective. Please retest, if problem persists copy down Failure ID code and contact HP support.
So I retested it but same story happened again
Now you know the identification code
What should I do?
Failure ID: UC462J-56C6NU-PXG03G-Q0NX03
Qanea wrote:
Hello
I am not well eaten English so I do short...
I have this type of laptop: HP Pavilion dv6 - 3023ca Entertainment Notebook PC
I just installed a new version of windows 7 Home premium x 86
When I tried to install my display drivers her did not work at all
I had these problems as:
- I can't play all video files by KMPlayer (or any similar programs)
- Job of dosen't effect Aero (trouobleshooter said that it is because of my type of graphics card or driver)
- I can't use the option of sleep to the start menu
Here is a picture of Deviece maneger:
If the drivers must be installed correctly
But it still does not work
I downloaded all drivers (I used the site AMD official and even here I have even updated their Windows) but still I got the problem
So I used HP Support Assistant to troubleshoot and test my card graph (or display)
(Home > troubleshooting > graphics, video and display > video check HP)
It took just a minute to give me this error:
Test Result: Fail Failure ID: UC462J-56C6NU-PXG03G-Q0NX03 HP Graphics Video Check detected an issue while running. The directx SetCooperativeLevel function has failed. Graphics card may be defective. Please retest, if problem persists copy down Failure ID code and contact HP support.
So I retested it but same story happened again
Now you know the identification code
What should I do?
Failure ID: UC462J-56C6NU-PXG03G-Q0NX03
Hello Qanea.
I looked at the failure code and confirms the results of the test. The video card (the card integrated Intel HD) is having problems. It probably needs to be replaced because the question is right after a reinstall of Windows.
Have you tried running HP Support Assistant to ensure that the laptop is to install all the correct drivers? Here is a link.
Could you provide me the product number? I can use this information to get you details instructions to replace the motherboard, which is the most likely solution to this question. This document can show you where it is located.
If you do not want to repair the laptop you can always contact the HP support directly. The number for US / Canadian customers is 1-800-474-6836. If you are in another part of the world, you visit HP's Support around the world to find the coordinates for your region.
Have a great day.
-
Problem with the HP 15-r033tx drivers.
I can't find a driver for my hp15-r033tx for win8.1 (64-bit). Please provide the drivers, it would be really grateful.
Hello:
Here is the link to the support page and driver for your model.
http://support.HP.com/us-en/product/HP-15-R000-notebook-PC-series/6875200/model/7308901/drivers
Select W8.1 operating system from the menu drop down.
Maybe you are looking for
-
I can't run even system restore!
-
I put windows 8.1, I used the key to everything going well I didt as the way windows 8.1 was, but now I want to move to this new can I use the windows 8.1 key new My windows 7 and 8.1 are authentic Installed windows 8.1, went to Windows 7, now, I wan
-
9.1 CUCM and 8.5 CUPS compatible?
Hello made the CUPS 8.5 is compatible with the CUCM9.x? We plan to upgrade a CUCM8.6 to 9.1. But do not want to upgrade the CUPS8.5. the CUP8.5 will work with CUCM 9.x? I have not seen any document on the compatibility matrix, that's why I sent this
-
URL OF THE LINK COLUMN IN THE FORM OF MANUAL
Hi allI have a problem with my APEX Solution. I created a manual tabular presentation, that works perfectly. But the problem is I want a convert (Projectname) - SQL query to a URL link. The link goes to the same application, but another page with par
-
. The VMDK file Split size
I use Pro Workstation 12.0.1 and created a 8 TB disk and selected the option to split the drive into 2 GB files but it is split into many more large sizes (did not at the top yet, but the first is more than 15 GB). I noticed that my 40 GB hard drive