Problems in connection to the mobile network after upgrading to iOS 9.2.1

Similar Questions

• HPC8180 printer connects to the wireless network, after upgrade firmware to the router wireless

  My HPC8180 has been wireless since I bought it some time ago.  I recently had to upgrade the firmware on my router wireless of Netcom NB9W and since then my HP will not solve for the wireless network.

  I run the wizzard of wireless network on the printer, select the correct SSID and enter the WEP key according to the instructions.

  It will then not connect.

  Print the summary I have says that it passes all except:

  No filtering = Fail

  Connected = do not run

  Signal strength = very weak (which is strange because it is about 10 feet away from wireless router).

  Other networks detected matching your network name (SSID) = No.

  Summary says:

  Network Name (SSID) altnet (correct)

  Address IP = not applicable

  Configuration source = not applicable

  Communication mode = Infrastructure

  Authentication type = open system

  = 64-bit WEP encryption

  I have NOT activated the mac address filtering

  Any ideas?

  Your router appears to be a DSL modem-router.  Those who can be difficult to connect to.  In addition, WEP can be problematic and is no longer a measure of security.  WEP can be broken in 10 minutes approximately with the freeware on the internet.

  We will do three things:

  1. replace the WPA or WPA2 encryption.  You can make your own password.  Do 13 or more characters, numbers and uppercase and lowercase letters.

  2 reset the default settings on your printer network (configuration > network area).

  3. attach to the router in this way:

  Sometimes the DSL providers have more control over the router like the printer.

  -Unplug the phone line from the router
  -Cut the power to the router, wait 30 seconds, then turn on the power.
  -Go through the normal process of the printer connected to the device (wireless configuration wizard)
  -Now to find the IP address of the printer (it should be on the self-test printout), type it in a browser.
  -On this screen, you will find a tab management network, then on the left wireless, then the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you know what it is, set an IP address outside this range but not exceeding 254 (the last number of the address).
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Let the white gateway and DNS
  -Finally, connect the telephone line, restart the router and the test.

• BlackBerry smartphones can not connect to the Mobile network

  Hi there, I really hope that someone can help me with this frustrating problem. I have a Verizon Blackberry Curve 8530 I bought on eBay. I have not had any problems to get the phone activated and it worked like a champ. A few days earlier, the battery got very low and my connections disabled. I charged the phone and now it won't let me connect to the mobile network! When I select the option it tries to connect and a red 'X' appears and it does not connect. However, it WILL connect to WiFi. WTF.

  Hello!

  I suggest the following:

  (1) dial * 228 and select Option 1. To make again, and select Option 2.

  (2) registry HRT

  • Homescreen > Options > Advanced Options > host Routing Table > (it matter little what line is current) > sign up now

  (3) Service reference books

  • KB02830 Send the directories for the BlackBerry Internet Service

  (4) batt Pull Reboot

  • Each time a random strange behavior or slow creeps, the first thing to do is a battery pop reboot. With power ON, remove the hood back and remove the battery. Wait a minute, then replace the battery and cover. Power on and wait patiently through the long reboot - about 5 minutes. See if things return to functioning. Like all computing devices, BB suffers from memory leaks and others... with a hard reboot is the best remedy.

  I hope that will move things again for you! If this isn't the case, then you must contact VZW for assistance.

• Connection to the local network after the connection to the Client AnyConnect Secure Mobility Client

  I connect to my network of business using Secure Mobility Client of Cisco AnyConnect.  Once connected, I can no longer print on my printer LAN attached and other local resources.  I use the router E4200 of Cisco/Lyncsys on my local network and can re - connect to storage on the local network by putting in place of Port Forwarding port 21 and the sharing of MS Windows FTP folders.  However, I can't connect to a client of the Terminal Services by transferring port 3389.  Is there a way to connect to the local LAN after scoring in the VPN connection.  I can connect to sites HTTP/HTTPS regulars and more than another type of connectiins, just not my own local resources.

  Thanks in advance... JS

  Happy to help, for what it's worth. Please mark question as answered if it is indeed and rate if the response is useful.

• Motorola Milestone does not connect to the corporate network after updating to Froyo...

  I've updated my Milestone that is the version of Froyo UNITED Arab Emirates yesterday after a long delay, was really excited all night until I've discovered two problems with my wifi.

  The device does not connect to the corporate network, as my office uses EAP 802.1 x and there is no place to enter proxy where my friends using samsung galaxy s (Froyo 2.2) connect to the network and navigate using the wifi settings advanced to enter the proxy in their device.

  Any help? Please, I beg you.

  Hey Ronald, I've updated by upper about the update saying that UNITED Arab Emirates and EGYPT got last week. Don't know if the Saudi version has achieved, you have the Saudi Version or is it the same in the UNITED Arab Emirates. If his UNITED Arab Emirates you can do it via the PC using Software updater by Motorola...

• BlackBerry Z10 a Z10 works fine, the other one has trouble connecting to the mobile network

  Hi, my wife and I have the Z10, and we're both on the same mobile network (Wind Mobile to the Canada). Z10 wife seems to have no problem connecting or staying connected to Wind Mobile. Mine on the other hand seems to randomly drop the connection, or struggled to get connection and sometimes ends homelessness.

  The only difference between the two of the Z10 is its is purchased through Wind Mobile itself, it is locked to their network at the moment. I bought mine a little later and I bought mine directly via the webshop of Blackberry, and it's why, mine is unlocked. What I have to do sometimes is to disable the mobile connection and turn it back on and it works after I do this. However, it is annoying, as I would rather automatically retry the network connection so that it is not go roaming in my own city.

  It is possible that a new sim card can help. Worth a try. I'm guessing, however, that, since one is that she has the ability to see other networks when the locked is not unlocked.

  That said, I use a unlocked Z30 and don't have these problems. Try a new sim card and see what happens.

• Unable to connect to the college network after installing Vista business on Satellite A215

  I have a Satellite A215-S4757, which I brought with me in College, I was told that the server of the College has a problem with vista home, which is what I currently the wireless is down, so after installing business and plug in the ethernet cable, my laptop does not collect several wireless networks available, or otherwsie

  What to say that you can also access the network using Vista.
  But please note that the Vista operating system supports additional network access security settings that should be disabled or reset.

  How this site published by Microsoft should help you set up the network with Vista settings:
  http://windowshelp.Microsoft.com/Windows/en-us/networking.mspx

  Here are several tips:
  You should try to open Network Diagnostics by right-clicking the network icon in the notification area, then click on diagnose and repair.

  Vista supports additional firewall options. Please disable all trying to connect to the server.

• Unable to connect to the wireless network after Windows update

  Original title: after receiving an update from Microsoft last week, my wireless is not working. He died immediately after the update. Why?

  My wireless does not recognize any of the wireless networks that are in my area. The driver manager indicates that the wireless driver works correctly. The wizard does not work and the Center wireless says that it cannot solve the problem.

  Hi JeffreySessions,

  ·         Do you have update installed?

  Follow these methods.

  Method 1: Follow the steps in the article.

  Solve problems, find wireless networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  Method 2:  Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  Startup options (including safe mode)

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Step 2: If the problem does not persist in SafeMode with network, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After the boot minimum troubleshooting step, follow the link step 7 to return the computer to a Normal startupmode.

  Method 3: Update the latest drivers for the network card.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 4: Follow the steps in the article.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows?T1=tab04

  Wireless network card: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions

• Unable to connect to the home network after you connect to the internet at Duke University

  Noteboook W7 Pro cannot reconnect to the network after you connect to the internet as a comments/visitor at Duke University.  The Duke system is predatory changes to my computer, and I can't fix it with the restoration of the system.   The home network is a Windows workgroup with most XP, no password only required machines.  This has happened in the past when the guest was an XP machine too, and then he had something to do with the DNS settings.  Cost me a lot of time and anguish and loss of productivity.

  Hello

  1. do you get an error message? If Yes, what is the exact full error message?

  2. are you able to connect to the internet?

  See the help article and check if it helps.

  Method 1

  Identify and resolve home network problems

  http://Windows.Microsoft.com/en-us/Windows7/identify-and-resolve-home-network-problems

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows#section_2

  Method 2: Check if the problem persists in the boot.

  To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to solve the problem by running the clean boot in Windows 7
  http://support.Microsoft.com/kb/929135

  Note: Once you have completed troubleshooting, perform the steps in the step 7: to reset the computer as usual.

  See also:

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Let us know the status of the issue.

• problems re-connecting to the wireless network

  Running vista on new hp computer, printer is hp deskjet 3052 was that was connected and working just fine and all of our other computers on the home network wireless could access the printer. Lost connection for some reason after working for almost a year, now try to get it back. Ran test wireless network and wireless is lit, wireless work pass, under network, he said the network name (ssid found)... IN CASE OF FAILURE. So under the current confiruration it says network name (ssid not defined). How to reset it? We recently changed internet providers so I know that we need to define the new network on the rise but don't have the installation disc or the manual. Thanks for any help.

  Hello

  Please see the following document on how to configure the printer on the network.

  http://support.HP.com/us-en/document/c02722113

• Z10 Z10 blackBerry does not connect to the mobile network

  I live in an apartment and sometimes when I get a no signal (like the elevator or the basement) location in a place where there should be a signal strong, the Z10 I have isn't always connect to it. Instead, I see that the network is listed as "SOS" or "302-500".

  My ISP is Wind Mobile to the Canada. The Z10 is a factory-unlocked directly from Blackberry. I already changed the SIM card once, but it didn't seem to help.

  Try this: settings, network and connections, Mobile network, manual network selection Mode change.

  It should automatically scan, can take a few minutes, when the Scan stops choose wind, do not choose any others listed will not work.

• BlackBerry cannot accept the connection via the Mobile network?

  Hi all, on Blackberry, I want to open a server socket to listen to a connection come from other devices.

  Here is my code:

  String url = "socket://:12345;deviceside=true";
  ServerSocketConnection scn = (ServerSocketConnection) Connector.open(url);
  SocketConnection sc = (SocketConnection) scn.acceptAndOpen();
  

  Mobile network on that BB is ok, but it cannot accept any connection.

  I also use its mobile phone network to connect to other servers, it works fine when it's the client socket.

  I tried with the Wifi network, and it works very well.

  String url = "socket://:12345;interface=wifi";
  ServerSocketConnection scn = (ServerSocketConnection) Connector.open(url);
  SocketConnection sc = (SocketConnection) scn.acceptAndOpen();
  

  In my view, Network Service Mobile prevented so that other devices connect to it, is it true?

  Please explain it to me, thank you very much!

  This approach only works for mobile connections, when the data are pushed to the device.  You cannot use it to connect to other phones directly.  Sorry

• Satellite Pro M70: No connection to the local network after removing the cable

  I have some problems of Mayor. The first time that I go on the internet - no problem. But if I get out my internet cable and plug it again it dosen't work! ??? I get the same IP, subnet and gateway. Everything seems fine. But the connection does not work until I restart the computer.
  Help, please

  Hello

  What do you mean with no link? If you have the same IP, subnet and gateway then the connection should be available.
  Perhaps mean you that IE cannot open Web sites.
  Anyway, if I have problems with my LAN connection I right click on the LAN icon in the taskbar and then I chose the option repair.
  The IP, the subnet and the gateway will be updated and the connection works again.

  Check also.

• Satellite Pro U300: No connection to the local network after updating BIOS 5.00 - WIN (Vista32)

  Hello!

  After the bios update newest to my Satellite Pro U300 (PSU31E) Lan Realtek adapter not working anymore. The map shows in Device Manager, but if I connect a cable, nothing happens (it says no cable connected).

  ipconfig-all says:

  Adapter Ethernet LAN connection:

  Medienstatus...: En medium (disconnected)
  Suffix-Verbindungsspezifisches DNS:
  Description...: Realtek RTL8101 Family PCI - E Fast Ethernet NIC (NDIS 6.0)
  Physical address: 00-1B-24-98-D7-AA
  DHCP aktiviert...: Ja
  Autokonfiguration aktiviert...: Ja

  Thanks for your advice!

  Hello

  In your case I would uninstall the Realtek LAN driver.
  Can I visit the Realtek and download and reinstall the latest LAN driver.

  In addition, in the DOS command window, you can try to run this command:
  * Ipconfig / renew *.

  PS: Try to also set the default BIOS too.

  Concerning

• BlackBerry smartphones does not connect to the Device Manager after upgrade [USB]

  Hello

  I've updated de.141.151 and just after the update has been made, whenever I try to connect my BB via USB, I get the message says:

  "Unrecognized USB device".
  The USB devices for computer mark attaached has malufunctioned and windows does not recognize it. "

  I tried cutting things:

  -Restart of BB

  -Restart the PC

  -Repair the current installation of Desktop Manager

  -Restore an older version of the Desktop Manager version

  PS: it is not unknown devices in the 'Device Manager' of the pc so there is nothing to uninstall and reinstall

  All are taken out with no results,

  any suggestions?

  Thank you.

  Found the solution, remove the battery after the closure of the DM, connect the usb cable and then replace the battery, the pc will read it.