Problems in USB drive mode

Similar Questions

• M9U93PA: problem wih usb driver for my laptop

  need driver for my usb driver.,.

  the hardware id is below. pls send the driver

  PCI\VEN_8086 & DEV_22B5 & SUBSYS_80C5103C & REV_21
  PCI\VEN_8086 & DEV_22B5 & SUBSYS_80C5103C
  PCI\VEN_8086 & DEV_22B5 & CC_0C0330
  PCI\VEN_8086 & DEV_22B5 & CC_0C03

  Hello

  Try the driver on the following lin k.

  https://Downloadcenter.Intel.com/download/24896/USB-3-0-Intel-USB-3-0-driver-for-Intel-NUC

  Kind regards

  DP - K

• problem of USB driver for HP pavilion 15 computer laptop n028se

  Hello, I have installed windows 7 64bet and installed all the drivers and windows update, but the usb port driver is not installed and windows cannot find the driver... Please any help?

  Hello:

  You need the usb driver 3...

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5359407&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_118604_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• problem with USB driver in windows 8

  I use winsows 8 in hp probook 4440 s with processor i3.  Recently I have a problem with my usb ports 3. they do not react like usb 3 and most of the time does not at all. I looked for a host controller driver expandable usb 3 for windows 8, but can't find anywhere because it is built with windows 8. Where can I find the driver or what can I do now?

  Hello

  Check with HP Support, their drivers and documentation online and ask in their forums
  on known problems. The drivers are from HP. update the BIOS, chipset and the major
  device drivers embedded and separate that may affect the USB.

  HP support/troubleshooting & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  ====================================================

  Update driver and troubleshooting details (don't forget to check for BIOS, chipset,

  (and other drivers):

  Microsoft - hardware and drivers
  http://Windows.Microsoft.com/en-us/Windows/hardware-drivers-help#hardware-drivers-help=Windows-8

  Why Windows is not find my device?
  http://Windows.Microsoft.com/en-us/Windows-8/why-isn ' t-windows-conclusion-device

  What happens if a device is not installed correctly
  http://Windows.Microsoft.com/en-us/Windows-8/what-device-isn ' t-installed-correctly

  Check with the manufacturer of system (manufacturer of motherboard for customized systems) updated
  the BIOS, chipset of low level driversand the major device on-board and separate
  drivers. Execute DriverView - value VIEW drivers Microsoft hide - updated from those
  without drain to their name.

  -Free - DriverView utility displays the list of all device drivers currently loaded on your
  System. For each driver in the list, additional useful information is displayed: load address
  of the driver, description, version, product name, company that created the driver, and
  more.
  http://www.NirSoft.NET/utils/DriverView.html

  To check system drivers manufacturer as replacements and camera manufacturer who are most
  current. Control Panel - device - Display Adapter Manager - note the brand and
  fill out the template tab of the driver for your card video - double-click - write down the
  the version information. Now click on UPdate Driver (this can do nothing as MS is far behind
  certification of drivers) - then do a right click - Uninstall - REBOOT it will refresh the driver
  stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if
  3rd party with their own software and drivers and the other main device drivers you
  a.

  Now, go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration), and then
  Site of the manufacturer of the device (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions.
  (Review of the BIOS, Chipset and software updates on the site of the manufacturer of the system while there).

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT
  After each installation.

  Always check in the Device Manager - drivers tab to be sure the version you install
  actually arises. This is because some restore drivers before the most recent is installed
  (particularly that audio drivers) so install a driver - reboot - check is to be sure
  installed and repeat if necessary.

  Repeat BTW to the manufacturers - manufacturers of devices DO WORK DO NOT THEIR SCANNER-
  manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Installation problem Z5 USB driver Win7 64 bit

  Hello

  I downloaded the real driver for the Sony Z5 package. The Device Manager shows me the E6653

  but with the downloaded drivers, it will not install these. Device Manager says there is not compatible

  driver for 64-bit systems.

  Anyone who can help me?

  Thank you!!!

  Hey,.

  Sorry for the delay of the answer!

  In the meantime, I solved the problem by myself.

  However the system does not detect the driver itself, so deciced to my Xperia Z1

  back on the WIn7 64 bit system. This phone worked properly on the system.

  I looked after the Z1 used driver and after that I return the Z5 and I have manually

  Select the driver as a TPM with the drivers Microsoft of WIn7 himself and tataaaaa it

  now it works!

  Thank you all for the help guys! :-)

• Toshiba 40LV933G - no user settings in the quick menu in usb drive mode

  Updated to the latest firmware and in don't you liking meu for colors in media player... He was there before the firmware update... now, I have just the predefined dynamic, standard, movie, the game and animated...

  any help?

  The Toshiba 40VL933G isn t mentioned in the [update information Firmware excel spreadsheet | https://portalcp.toshiba-tro.de/documents/10781/5bafb15d-5e41-46b9-97d2-57dfc56c7699] and therefore it s does not clear enough, which was changed in the update.
  However, its always advisable to reset your TV after a FW update via the USB port or network so that the changes become activated.

• Missing USB driver

  original title: USB Driver

  problem with USB driver for Vista home edition - the driver is gone and I can not find replacement, have no disk Vista - can upgrade to Windows 7 the problem?

  
  

  Hello

  The upgrade to Windows 7 may not help the problem at all. Try the top of methods down below and if
  they do not contribute and then copy the examples of "How to ask a Question" to give us more information
  to help us help you.

  How to ask a question
  http://support.Microsoft.com/kb/555375

  ---------------------------------------------------------------------------------------------------

  Check the configuration/settings (BIOS/CMOS) often F2 when you start - make sure that USB is enabled.

  If a PC and if necessary the embedded USB can be disabled and a USB card can be used only
  is not expensive. For a laptop, using a real computer shop (no leeks and glances at a Best Buy
  or other stores) or system manufacturer support.

  ------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
  Devices disabled - look around (with the exception of USB controllers) for your devices (can have
  zero or more than one) and top - right click UNINSTALL.

  Control Panel - right CLICK on EVERYTHING - Serial USB controllers - Device Manager and UNINSTALL
  all except the category itself - REBOOT - it refreshes the drive and battery USB

  This KB shows XP how to and the method of Vista is identical
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer, thus
  as all USB devices that you previously used. Run Options and check the 1st three choices to see to it there
  Is there.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  =========================
  =========================

  If necessary after the foregoing:

  You can try a repair install or an upgrade in Place. Be sure to do a good backup or three.

  You can use another DVD that aren't copy protected but you you need to own
  Product key. This also requires correct Vista disks especially for OEM versions. You will be
  need to know your product Code.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• My computer Toshiba Satellite keeps the 'blue screen' and that is to say that it is caused by "a problem with a USB driver. How can I fix it?

  Resolve a problem with a USB driver

  You have received this message because your universal serial (USB) bus driver caused a stop error, also known as a blue screen error. This error means that the computer has stopped abruptly to protect against potential corruption of data or loss.

  What is a driver?

  A driver is software that allows your computer to communicate with hardware or devices. Without drivers, the hardware you connect to your computer (for example, a video card or a webcam) may not work properly.

  The recommended steps that follows can help to eliminate this problem, or at least reduce its frequency. Try them in the order listed. If a step cannot solve or reduce the problem, then move on to the next.

  Steps to fix this problem

  1. Adjust your computer's power settings

     The following power settings may help reduce the frequency of this problem.

     1. Turn off the USB selective suspend setting:

        1. Click on the Start button .

        2. In the search box, type power options, and then press ENTER.

        3. Find the plan selected, and then click change plan settings.

        4. Click change advanced power settings.

        5. Double-click the USB settings , and then double-click on USB selective suspend setting.

        6. Make sure that the USB selective suspend setting is disabled. If it is enabled, click it and select disabledand then click OK.

     2. Disable power saving mode (computer portable computers only):

        1. Click on the Start button .

        2. In the search field, type power options, and then press ENTER.

        3. Under Preferred Plans, ensure that High Performance is selected, and then close the window.

  2. Look for an update of the BIOS for your computer system

     Several computer manufacturers whose computers have this problem published BIOS updates to fix this known issue. Contact your computer manufacturer to see if a BIOS update is available for your computer model.

     What is the BIOS?

     The basic input/output system (BIOS) is software built into a computer that runs when the computer is turned on. Among other things, this software starts the operating system, and supports the transfer of information between hardware devices (such as the keyboard and the monitor).

     How can I find the manufacturer of my computer?

     Click on the Start button , type msinfo32 in the start search box and press ENTER. The manufacturer of your computer is listed as the manufacturer of the system in the right pane of the system information window.

     Click here to go online to see the contact information for most of the computer manufacturers

  3. Download and install the latest updates and drivers for your computer

  It's a good idea to periodically check the updates of driver for your computer, especially if you added new hardware recently, such as a USB hub or other USB device.

  What is a USB hub?

  A USB hub is a device with multiple (USB) universal serial bus ports. USB ports are narrow and rectangular connection points to connect USB devices to your computer. A USB hub is used an Extender of port or port replicator, providing more USB ports to run from a USB connection on your computer. USB hubs can be external devices that connect to a USB port, or they can be internal devices built into your computer.

  To check for driver updates:

  1. Use Windows Update to find and install updates:

     1. Go online to Windows Update

     2. Click the check for updates in the left pane, and then click view available updates.

        What happens if I see any updates available?

        • If you see you receive updates: managed by your system administrator, you can try clicking on the link to check online for updates from Microsoft Update or Search online for updates from Windows Update, but you should maybe contact your system administrator to get the desired updates.

        • If you do not see the message above and no update is available in Windows Update after clicking on the link check the updates in the left pane, then the available updates have already been installed.

     3. Select the driver for your device updates and more updates to install.

        Note
        We recommend that you install all Important updates and recommended. These updates improve the security and stability of your computer.

     4. Click on install. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  2. If you recently added a new hardware device on your computer, go online to the manufacturer's Web site to see if there is an update to the driver.

  3. If you recently added a new program on your computer, go online to the manufacturer's Web site to see if an update is available.

  Steps to work around this problem

  Warning
  These measures are intended to solve a specific problem, but could do so by temporarily disabling or removing some features on your computer.

  1. Try to remove newly added USB devices

     If this issue occurs after adding a USB hub or other USB device, consider removing to see if the problem goes away. If this resolves the problem, contact the manufacturer of the device for the updates or other recommendations.

  2. Do not disconnect USB devices while the computer is to stop or go to sleep

  This problem is known to occur when USB devices are disconnected when the computer is trying to stop or switch mode to 'sleep'. This is common with cell phones, especially those with a docking station, as docking station can act as a USB hub. The frequency of this problem could be reduced by allowing your computer to completely close or completely in sleep mode before detached from its docking station or unplug it or the docking station USB devices.

  If you know which USB device is causing the problem

  It may be possible to prevent the Blue error screen by choosing the option remove the device safely in the Notification area, before putting your computer into sleep or Hibernate mode.

  1. In the system tray, click the icon to remove the device , select the USB device that you think that the origin of the problem and then click OK.

  2. Do not physically remove the USB device.

  3. Perform the action which resulted in the Blue error screen, so that was taken the functioning of your computer after the mode standby, hibernation, or, in the case of laptops, close the laptop computer or place it in a docking station.

     1. If the Blue error screen persists, it is likely that the problem is with another USB device. Try this procedure using other USB devices until you find that at the origin of the problem.

• If the Blue error screen disappeared, you have probably identified the device causing the problem. Contact the manufacturer of the device for more information on how to solve this problem, or use the option to remove the device safely to work around him.

Note
Depending on the manufacturer and model, some USB devices will become available automatically when you resume using your computer. Others will require that first disconnect you physically and then plug back in front, they will be recognized by the computer. Check the system tray to see if the USB device that you removed safely become available when you started to use your computer again. If she did not become available automatically, then physically unplug it and then plug it in again.

This is the screen it gives me. Help, please! If problem fixed, will BE AWARDED!

Hi ChayceSteffiare,

For instructions on solving problems with USB devices, see the following article:

Tips for solving problems of USB devices

To fix blue screen errors, see the following article:

Pick up the pieces after a computer crash

See also:

Optimize Windows Vista for better performance

Ways to improve your computer's performance

• USB drive unplugged when wake up mode 'sleep'

  I use windows vista business version for my 6400 Dell insporon laptop.

  When my laptop wakes mode ensures, in the wondows login procedure, it seems he disconnected from usb drives to not communicate with windows at this time. One of the USB (simpletech 2 TB) was not connected (it loses the drive letter in windows Explorer). Two other brand always connected.

  If I recycle the power of this USB, it connects back.

  Simple question: where can I change once and for all so that I don't have to recycle that drive usb every time when you wake up mode 'sleep' (she becomes very annoying since this USB does not start button / stop)? Personally, I think it's microsft windows 'default login procedure question' no usb drive manufacturer bug (contact usb drive tech support).

  Thanks in advance for any help.

  Hello

  The problem is perhaps due to several parameters being off, and you can actually have
  go through the list again. It could be you have a hardware problem with
  the USB port or might have to reinstall Windows. Even if it is complex you need to use this
  keep track and not as a menu.

  Another possibility is to use a clean boot to see if something in startup is at least partially
  in the mixture. It is the only method of control similar to your idea about the login procedure.

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Autoruns - free - see what programs are configured so that it starts automatically when your system
  boots and you login. Autoruns shows you the full list of registry and file locations where
  applications can configure Auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx Rob - bicycle - Mark Twain said it is good.

• The conclusion for M - Audio MobilePre USB driver problem

  The conclusion for M - Audio MobilePre USB driver problem

  Use: iMac

  OS: El Capitan 1011.2

  The latest driver I could find was 1.8.1.

  Error message:

  Installation failed - Setup could not install the software because there was no

  available software

  I would use this hardware with Final Cut ProX 10.2.2 and Garageband 10.1.0.1

  A quick search seems to indicate the latest version of the driver to be 1.2.1 - there was no 1.8.1 I could find. It has been out for more than a year, so no mention of El Capitan, but it could work. I'll make sure that you have the right to download and try again.

• __Vista and external hard USB drive problems. __

  I have an old USB Maxtor attached an external hard drive with vista home premium.  It was working fine until I left for two weeks.  Now, vista starts up with this drive connected.  When I unplug the USB connection, it starts OK.    Second, but related.  I use this drive to Flash the pictures on the box of the gadget.  Works OK for a bit, then the photos appear more.  I redefine the source folder to make it work again.  The two problems are related to the external hard drive.  Is it vista, usb or drive?

  Any help would be appreciated.

  Vinnie

  Hi Vinnie,

  I suggest you try the following steps to refine the question:

  Step 1: connect the USB device to a different USB port and test it.

  When a device is not functioning, Device Manager also typically displays an error message with an error code that comes with it. First, search for errors in the Manager of devices to do this, follow the steps below:

  Step 2: Disconnect the USB device, then on startup, check for the error code in Device Manager

  1. open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager.
  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  2. in Device Manager, look for the USB device, and then double-click the device name.
  3. under the gaze of general tab for the status of the device for any error code indicated.

  Get-help-with-Device-Manager-errors
  http://Windows.Microsoft.com/en-us/Windows-Vista/get-help-with-Device-Manager-errors

  Step 3: Disconnect the USB device and start, run the fixit provided in the link below at the office level.
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Thank you, and in what concerns:
  Ajay K
  Microsoft Answers Support Engineer

  --------------------------------------------------------------------------------
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problems pictures copies of Flash memory card and USB drive under Vista 64 files

  Hi, when I insert a flash memory card (SanDisk 8 GB SDHC or SanDisk 2 GB Compact Flash) either by inserting the card into a card reader, AutoPlay comes on but the image transfer stops after a few images have been copied to any program (Windows, Picasa, etc.). I chose to copy the files. Same experience when I connect the camera with the memory card in the camera using the USB cable to the PC. I tried to re - format camera memory cards, but it has no effect.
  Also, I feel the same when I try to copy from a USB flash drive (the drive is basic, not a U3 key).
  I have a HP Pavilion m9400t Elite desktop running Vista Home Premium 64-bit. I own this desktop computer for a year and I've always had this problem. I have no problem using these flash memory cards and a USB drive on my old XP PC or an Apple Mac Book. For what I can tell, my Vista desktop is set for automatic windows and updates from HP. Everything about the plan of updating drivers, etc., which would solve this problem would be appreciated.
  Thank you
  Srini

  Hi Srini,

  one) that you get specific error messages when images are arrested to copy?

  (b) what is the file format of the pictures\files that are not copied? What images are copied with success?

  To narrow the problem, please follow the steps mentioned below:

  O copy the pictures manually on the flash memory card Office.

  O connect the flash memory card\ camera to the back of the computer (for a different USB (port universal serial bus) and try to copy the pictures\files.)

  O check if the photos are in double version:

  Windows detects your newest pictures and doesn't matter the duplicate versions of the old photos that you've already copied to your computer

   

  He may want to know:

  How can I get pictures from my camera to my computer?

  http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-get-pictures-from-my-camera-to-my-computer

  Troubleshoot camera connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/Troubleshoot-camera-connection-problems

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Video device USB has a driver problem__ __There is a problem with the driver for USB video Device.__Device information __Name: __ID USB video device: USB\VID_05CA & PID_180C & MI_00\6 & 69C3BD0 & 0 & 0000 code __Error: 10 _ _ _

  I hava a dell inspiron 1440 with windows 7 and a a few days ago, my webcam was working just fine but know that it gives me this after troubleshooting

  Has a USB video device driver problem

  Not fixed

  There is a problem with the driver for USB video device. The driver must be reinstalled.

  The device information

  Name: USB video device ID: USB\VID_05CA & PID_180C & MI_00\6 & 69C3BD0 & 0 & 0000 Error code: 10

  Hey laloo.16,

  As the error message states clearly that reinstalling the driver is required, please do the same. You can uninstall the driver that is currently installed from the Device Manager.
  To access Device Manager:
  1. go to start and type Device Manager.
  2. Select Device Manager in the control panel list.
  3. go to your device.
  4. to remove:
  Right-click on it and select Properties.
  5. Select the driver tab and click on uninstall to uninstall the existing driver.
  6. close Device Manager.
  Now go to the link below. Download the Dell WebCam software for your product.

  http://support.Dell.com/support/downloads/DriversList.aspx?OS=W732&CATID=-1&DateID=-1&impid=-1&OSL=en&typeid=-1&FormatID=-1&SERVICETAG=&SystemID=INSPIRON1440&hidos=WLH&hidlang=en&TabIndex =

  Please choose the appropriate version of Windows 7.  Install the driver and see if that brings your webcam to work.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows 7 professional XP Mode - does not recognize external USB drives or internal DVD drive

  I recently bought a new Toshiba laptop and ordered computer configured with Windows 7 Professional that I can use the XP mode for some older programs.  Virtual Mode and XP mode work well, but the computer will not recognize the USB external storage drives or internal DVD player.  This prevent me to save and transfer any file I'm working on in XP mode.  Anyone know what I have to do to make the computer recognize USB drives and DVD drive internal when I'm running in XP mode?  Thank you!!

  Hello David,.

  Thanks for the quick response.

  Yes, it's a Microsoft Product, but there specific departments assigned to the people where they have more expertise, this is the reason why we have asked you to post your query in the TechNet where this issue is very discussed.

  Hope this information helps.

• Problem with USB 2.0 Driver

  I'm having a problem with the USB 2.0 driver. Whenever I connect my USB drive, I get a notification of an unknown device and I also used the troubleshooter to solve problems, but he said-

  An unexpected error has occurred. The Troubleshooting Wizard can not continue.

  Identifier of the package: DeviceCenterDiagnostic

  Path: unknown

  Error code: 0 x 80070002

  Source: engine

  User: Chinmaya-PC\Chinmaya

  Background: high

  Every time that I find this error code while troubleshooting the USB 2.0 driver. I even tried reinstalling the driver, but it's the same thing over and over again. I also tried to install Microsoft Fix it, but it won't install, it says "Microsoft Automated Troubleshooting Services BootStrapp has stopped working". Someone at - it this same error? I can't even connect a USB on my computer because of this error.

  If anyone has an answer, I would be very happy to know.

  Hello Chinmaya,

  Thank you for the update on the issue.

  Before any change in the registry, I highly recommend you back up the registry. You can see How to backup and restore the registry in Windows as described in the previous answer.

  UpperFilters and the LowerFilters are assigned values in registry keys. Upper filter drivers go between the operating system and the principal driver, and the lower filter drivers between the driver and the hardware.

  You can try the suggestion and let us know the result, we will be happy to help you.

  Thank you.