problems of configuration-esxi

Similar Questions

• My laptop is one of the 4 home cannot connect to the internet, it's Vista and it has connected w/Ethernet no problem, I called Xfinity tech, that says, is the problem of configuration! Can you help me?

  Acer laptop, Vista is, she can connect wirelessly with my friend modem but my house, she can't, I use the service of Comcast, they checked the modem is fine, they think that the problem of configuration! I'm not computer too, thank you!

  Ryan (Shih Chi)

  Hello

  How do you try to connect the computer to the House? Wired
  or wireless?
  Try the methods provided and see if it helps to solve the problem.
  Method 1:
  Check out the link and follow the troubleshooting steps in the article.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
   
  Method 2:
  If you try to connect to t Wireless net work then refer to this link and follow the steps.
  Connect to a network with Windows Vista wireless
  http://TechNet.Microsoft.com/en-us/library/bb878035.aspx
   
  Method 3:
  Reset TCP/IP on your computer and check. Check out the link and follow the steps.
  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357
   
  Method 4:
  You can also visit this link and follow the steps.
  
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us
   
  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/ ) how to back up and restore the registry in Windows

• Big problem with installing ESXi 5.5 on Cisco UCS M200 B3

  Hello

  I have a problem with installing esxi 5.5 on SDcard mounted in Cisco UCS B200 m3.

  ESXi Show map SD but when to start partitioning I question (attachment).

  If I install ESXi on HDD I don't see SDcard (even from the console).

  Thanks for any help

  h

  Marcel

  Hello

  Thanks for the reply but SDcard are clear. map of are new directly from Cisco.

  The good news is that I found a solution. I install the old version of ESXi (5.5 U1) and everything works fine

  Concerning

• Problem with my ESXI

  I have problem with my Esxi 5.0.when, I installed whenever I got a message.like like NO ADAPTER NETWORK NOT FOUND error in my ESXi software.

  How reslove it .or how to upgrade the lan installation software. Please give the correct soluction.

  A tried

  I activated the lan in the bios

  It could also be that your NETWORK adapter driver is included in the ISO file.

  If you NIC are supported (on the HCL) then you can simply load the appropriate driver or create an ISO custom (with the help of the image generator) with the correct driver added.

  Here are some links that you can check:

  Image generator:

  http://www.YouTube.com/watch?v=AfjEyB2FTwc

  http://virtualbill.WordPress.com/2011/08/19/VMware-vSphere-5using-Image-Builder-for-custom-installation/

  http://pubs.VMware.com/vSphere-50/index.jsp?topic=/com.VMware.vSphere.install.doc_50/GUID-C84C5113-3111-4A27-9096-D61EED29EF45.html

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=2005205

  Custom ISO

  http://www.ivobeerens.nl/2011/12/13/VMware-ESXi-5-whitebox-NIC-support/

  Drivers:

  http://downloads.VMware.com/d/info/datacenter_cloud_infrastructure/vmware_vsphere_hypervisor_esxi/5_0#drivers_tools

  BR

  A. Mikkelsen

• I have problems to install ESXi 3.5 in a Gigabyte G31M-ES2C Board

  I have problems to install ESXi 3.5 in a Gigabyte motherboard, fails the installation process, the console says fatal error, the entire message is:

  Model G31M-ES2C

  Serial number abandoned

  BIOS Rev: CF

  Help me, please

  ESXi is very demanding and specific with regard to the material. There is a very short list and I do not think that your software is on the supported list. You may be able to get hardware not supported for installation, but you must work there. I would look on the site http://vm-help.com for possible solutions for your hardware not supported.

• Backup configuration ESXi via PowerCLI

  Hello.

  Is it possible with PowerCLI (similar to the RCLI) to back up and restore the configuration of an ESXi host and how if possible?

  Or should we use the beast ulgy Pearl for this?

  Thanks for your help.

  Kind regards

  goppi

  Perl (esxcfg - cfgbackup.pl) both PowerCLI uses the vSphere API to deliver a configuration ESXi backup using BackupFirmwareConfiguration and RestoreFirmwareConfiguration

  Here is a PowerCLI script that seems to do the job: http://waynes-world-it.blogspot.com/2009/08/vmware-powercli-backup-esxi-40-firmware.html (have not tested personally)

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  repository scripts vGhetto

  VMware Code Central - Scripts/code samples for developers and administrators

  150 VMware developer

  Twitter: @lamw

  If you find this information useful, please give points to "correct" or "useful".

• Problems of configuration of SNMP 5.1 ESXi - .trp files accumulate after that SNMP is disabled

  Hello

  We had 2 problems with our new servers ESXi 5.1 has:

  1 vMotions to fail 13%

  2. some of the virtual machines are not accessible through their consoles. (Impossible to contack MKS)

  To resolve these issues, I came across the following KB:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 2040707

  I did the step necessary and even created a new host profile where the SNMP agent is disabled. However, on a successful remmediation of the new profile, .trp files continue to accumulate in/var/spool/snmp (above 3000 files in 2 days) and I have no idea what creates these files of trap and why.

  Anyone can shed light on this issue?

  This is solved in the latest version of vSphere 5.1 update 1.

  Release notes: https://www.vmware.com/support/vsphere5/doc/vsphere-esxi-51u1-release-notes.html

  ESXi host 5.x appears disconnected in vCenter Server and logs the ramdisk (root) is full message in the vpxa.log file
  If Simple Network Management Protocol (SNMP) is unable to handle the number of trap SNMP (.trp) files in the foldersnmp/var/spool/snmp of ESXi, the host may appear as disconnected in vCenter Server. You may not be able to perform all the tasks on the host computer.
  The vpxa.log contains several entries that are similar to the following:
  WARNING: VisorFSObj: 1954: unable to create the file
  /var/run/VMware/f4a0dbedb2e0fd30b80f90123fbe40f8.lck for vpxa process because the table of the inode of the ramdisk (root) is full.
  WARNING: VisorFSObj: 1954: unable to create the file
  / var/run/VMware/Watchdog-vpxa. PID to treat sh, because the inode of the ramdisk (root) table is full.

  This issue is fixed in this version.

• Problems of configuration of the NIC in ESXi 4.1

  I have a HP DL380 G7

  I loaded ESXi, the server has 6 physical NIC, 4 on board and 2 in a PCI Intel card.

  The system will accommodate 3 VM - all 2008 R2 Enterprise

  2 servers, I want the team to failover and load balancing

  I have configured my NIC this way

  NIC 0 dedicated to managing the virtual computer

  1 NETWORK card dedicated to a single server running as a domain controller

  Map NETWORK 2 and 5 I want the team to failover and a faster flow on a TS

  NIC 3 and 4 I want the team to failover and a faster flow SQL database running

  I segragated 2 NICd dual servers have a NETWORK card on each card, where a map should fail

  Here's where I lose myself-

  How can I add network cards to the actual virtual machines correctly?

  If the network adapters are associated, I see 1 NIC in each virtual computer or will I see 3 NICs in the actual virtual machine?

  If a virtual computer uses a bundled pair of network adapters, I should add the two network adapters, the settings of the virtual machine?

  If a virtual machine uses a pair of network cards grouped and I see 2 network cards in the actual virtual machine, I need to assign an IP address to each NIC?

  Sorry for so many questions, I'm just getting confused by properly installing network cards.

  I've included a screenshot of what I'm trying to accomplish.

  Vmnic0 is 1 Gbit/s and the others are at 100 Mbps.  Using 2 different physical switches?

  If so, I would put all 3 VMs on vSwitch1.  When you create each virtual machine you can assign just a single vmnic to it.  Then bind the vmnic for the VM port to vSwitch1 Group (which is called Terminal Server now).   Virtual machines will not be limited to 100 Mbps when communicating with each other.

• problem configuring ESXi AND ADAPTEC ASR-240

  When I try to add new storage by using the storage wizard. shows the location of the device: device of vmhba2:0:0 with 464,99 GB.  Thus, readers seem to be visible... but when I use the next button to move to current available to drive I get a messge "Cannot read from this disk partition."  I formatted disks using the configuration of raid bios... nothing more.  Any help?

  You might want to start by using a live CD or something similar, or get in the console not supported if you are willing to take that risk and use fdisk to write a partition table for readers.

• Very big problem on server Esxi on a data center

  Hi dear friends,

  IM using esxi virtualization server in a data center

  everything was good until the month last one of my server has the problem like this:

  When i install a new virtual machine when the installation ends and the operating system restarts and rises when he wants to recognize the network adapter

  the root server goes down. now all my servers to this DC have this problem and I can not add or turn on any virtual machine on that server.

  Anyone with this problem, if so, what is the solution?

  Help, please

  Thank you

  Just to clarify:

  You have an ESXi host.  Configure you a new virtual machine and install an operating system.  When the operating system restarts and tries to use in the host network ESXi restarts.

  Is this correct?

  Please give some more details:

  1. ESXi version

  2. Virtual Machine OS

  3. managed with vcenter

  4. virtual network for ESXi host and virtual machine configuration

  5. material the ESXi host is running

  6. nothing in the two papers that can help

  Thank you

  J

• Problems to configure FireFox to use a CAC reader

  I'm trying to set up Firefox so I can use my CAC card with her reader. My problem is when I try to load a module under Tools > Options > advanced > encryption > safety devices. When I try to load acpkcs201.dll (or any other other .dll files) I get an error message that says: "unable to load the module.

  When I try to use the add-on DoD configuration 1.2 of forge.mil, it is also unable to do this configuration.

  The ACC Player and the software works well in Chrome and IE. The only problem is the .dll file does not load in Firefox using the add-on or manually.

  Does anyone know how to make the module load correctly?

  I use:
  Windows 7 x 64
  Firefox 3.6.9
  SCR331 card reader
  ActivClient 6.2

  I met the same problem at first. I tried to load the *.dll files in obvious location - C:\Program Files\ActivIdentity\ActivClient. None of the files acpkcs*.dll and implement. Then I realized that the current version of Firefox is always a 32-bit program - it can not load the ActivClient 64-bit drivers.

  Try loading C:\Program Files (x86)\ActivIdentity\ActivClient\acpkcs211.dll instead. This has worked for me - the charge immediately *.dll and detected my ACC Player. I was able to successfully access the CAC restricted without any problem sites.

  My configuration:
  Windows 7 Professional x 64
  Firefox 3.6.10
  ActivClient 6.2.0.74 - BINDINGS 1002012

• D20 problem of configuration of Windows Server 2008 R2 / 1 x SATA HD / 4 x SATA SSD

  Hi all

  I have a Mod D20. 4155 and want to use next to it is by default SATA HDD SATA SSD four disks of virtual machines. Windows Server 2008 R2 will be the OS with the use of its Hyper-V features.

  I have Aproblem with detection of drives in the configuration of the operating system. All 5 disks are visible in the Marvell controller BIOS setup. It is possible to configure a RAID on the SSD, etc, but I don't "see" any disk in the configuration of the operating system. I tried to load additional drivers in the part of the Setup utility GUI, but it did not work. I tried with the driver Marcell SAS and Intel Matrix driver, both located at http://www-307.ibm.com/pc/support/site.wss/migr-72280.html.

  Suggestions for the BIOS of the PC / BIOS Marvell / OS installation configurations?

  Best regards, Chrischmi

  Hi all

  I found the solution myself. After detection, the default drive is a SATA drive (and), I got the idea to test it on the Intel SATA controller. It was possible to install the spirit of the machine the disks attached to the Intel controller. After installation, I went to Device Manager and installed the driver of Lenovo Marvell, rekindled the Marvell controller disk and started the. Successfully. Yes!

  On my way to the solution, I had another problem: in the setup of Windows GUI part, I got an error of 0 x 80300001 with Lenovo's Intel SATA driver. It was not possible to install windows Server on the SATA drive with reason0x80300001. very helpful post, Microsoft! (-) I decided to use the default Microsoft for the Intel SATA controller driver after a reboot. Installer executed well, but ended with an error 0 x 80070017 and problems of copy of (unknown) files. The solution (found after a few hours...) was to burn a new installation of Windows Server DVD. I don't want to talk about it anymore...

  -Christoph

• Problem in configuring the type of columns in a table

  I have a problem with Labwindows 2009
  I want to put a table with two columns, each with a different type.
  I need a numeric column and a string column.
  The problem is that I can't configure each of the types in the Edit menu of the table.
  If I set the type of the first column in the Numeric form, this becomes automatically equal.
  Can someone help me?

  Support persons OR confirmed to me that I want to do in version 2009 cannot be done.
  The way to do it would be to create a column and set it with the desired type. Then delete and re-create and so on for each column that you need.

• Problems of configuration of IPTV, WRT1900ACS.

  Hello. I have big problems getting my IPTV to work with my WRT1900ACS. I'm failry certain that it has something to do with something in the router configuration, but what and where is the question. VLAN? Port forwarding? If I go with my cable ISP directly on the uses of the socket of the TV, it works, but as soon as I go through my router, it doesn't. Everything else works, and after reading about this a little bit on the net, it seems almost obvious that I have to click or configure something in my Smart Wifi of Linksys. I'm a lot of people thought have had these problems and in the hope that they were able to solve them.

  Someone has good directions on where to start? I'll also call support for IPTV, but since signals will be mainly done in the router, my guess is that they will not be able to solve. I'm really grateful for any help I can get. I had so many technical problems the last few months, I don't even start taking place with them here...

  I live and the Sweden and the IPTV provider's Viasat. The box is a Samsung.

  Kind regards

  Thomas

  We are pleased to know that you were able to make it work. If you need our help once again, you know where to find us. Have a good!

• UCS C220 M3 custom problem after installing ESXi 5.1.0 Cisco

  Hello world

  I m using a Cisco UCS C220 M3 when I tried to install ESXi 5.1.0 custom Cisco after complete the entire process and restart the server. The ESXi has not started it appeared as if there is no operating system.

  In addition, before installing ESXi I configured a HDD in RAID 0, initialized the RAMDisk and chosen as a pilot.

  Hoping someone could help me.

  Llianovich,

  Unfortunately, the on-board controller is not supported with ESXi.  I saw other people using this controller for VMware and makes the work but the behavior is very random and it could work or fail at any time. It is recommended to use one of the controllers of basic PCI or Mezzanine by the ESXi (see c220 m3 datasheet below)

  STEP4SELECT CONFIGURATION of RAID (page 21)

  http://www.Cisco.com/en/us/prod/collateral/ps10265/ps10493/C220M3_SFF_SpecSheet.PDF

  Embedded MegaRAID controller

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/c/HW/C220/install/RAID.html#wp1028426