Problems when adding static routes to esxi 5.5 c

Similar Questions

• Adding static routes to ESXi host

  Hello

  Is it possible using PowerCLI to add static routes to ESXi host? If not, is there another way to add roads without using the console?

  Hello, leitsu-

  Yes, it is possible with PowerCLI.  Take a look at the New-VMHostRoute cmdlet.

• Add Static route on ESXi 5.5!

  Hello

  I am trying to add a static route in the esxi using the command 'esxcli ip route ipv4 network add x.x.x.x - n x.x.x.x/xx g '. When I run this command a static route is created and applied to vmkernel port group by default vmk0. I want the static route applied to vmk3 instead of vmk0. Please me tips on how to do it.

  Thank you

  TA.

  Hi Sai,

  It's easy :-)

  vmk3: 10.28.184.8

  iSCSI target: 10.28.184.10

  vmk3 and your iSCSI target IP address are in the same subnet, so there is no need for any gateway, by default or not, or for routing.  The IP addresses in the same subnet can speak throughout the day without leaving the subnet or involving communication via a gateway.

  Yes, all vmkernel ports assumes that the default gateway of the vmkernel, but vmkernel ports other management port management is generally useless to speak in the first place outside their own subnet.

  Some examples of use of vmkernel ports case how they communicate generally:

  NFS - should speak only within its own subnet

  iSCSI - should speak only within its own subnet

  vMotion - should speak only within its own subnet

  Fault tolerance - should speak only within its own subnet

  vSphere replication - can talk within its own subnet, perhaps one VLAN stretched if in different sites, otherwise a static route can be configured

  I missed everything vmkernel port types?  I think that all down for the most part.

  -Mike

  -----------------------------------------

  Remember to mark this reply 'proper' or 'useful', if you found it useful.

  Mike Brown

  NetApp, VMware and Cisco data center guy

  Consultant engineer

  [email protected]

  Twitter: @VirtuallyMikeB

  Blog: http://VirtuallyMikeBrown.com

  LinkedIn: http://LinkedIn.com/in/michaelbbrown

• Adding static route to the ACS

  How can I add a static route to my device SE ACS?

  I try to get AAA works on a Cisco 871 is an end of distance of a vpn s2s ASA to 871. On the router, I use as the source for Ganymede interface vlan1.

  My ACS server is on the subnet for my ASA management, but the GBA to the Remote LAN road is via its default gateway and interface from the INSIDE of the SAA. I need to get the traffic of Ganymede ACS to return through the management interface of ASA.

  Thanks in advance.

  John

  John,

  There is no way to set a static route in the GBA unit. The only network settings, you can set are the ip address/subnet, default gateway and dns servers.

  Kind regards

  ~ JG

  Please mark it is resolved so other can benefit from

• Nested ESXi - problem when adding the cloned ESXi hosts to the same data center in vCenter

  Hi all

  I installed a VM ESXi5.5 on top of WOrkstation10 and made a clone of it. Two of them are accessible and functioning very well themselves.

  However, when trying a add these hosts to vCenter, he begins to complain that:

  "Data store"datastore1"is in conflict with a store of data that exists in the data center which has the same url.

  and will not let me add the second host. Is there a way to fix this?

  Any help would be appreciated...

  Try to delete the local data store and re-create it.

• Problem when adding 2nd host in Iscsi storage shared

  Hello people.

  I'll try to explain exactly my problem even if it is a little difficult liitle!

  First of all, we are talking about a test environment that is installed in my house just for learning purposes.

  I am facing a strange my iscsi storage behavior when trying to join a second host to storage vmotion purposes. I was using an Esx host (3.5) for a while and I had no problem with the iscsi storage (I use an old pc with freenas on it). I must say that I got lucky, also, local sata controllers have been recognized so I could test the Storage Vmotion between two storages (Commons and iscsi) with success in this host.

  To continue to learn, I decided to also buy another pc to test Ha cluster, Vmotion, DRS. Unfortunately, I couldn't find the same material and who as well as sata controllers do not to be recognized, so I used a disk ata for OS and my intention was to use for the volume vmfs3 iscsi storage.

  In the first host esx I used, you can see 3 storage adapters: vmhba32 vmhba33& gt; Controllers local sata,34vmhba& gt; initiator iscsi software

  In the second esx host, you can see only the vmhba32- & gt; the iSCSI Software initiator.

  The first time everything worked ok, which means that I have attached iscsi storage in host the2nd by rescaning the vmhba and I was able to browse the datstore and see the contents of it, but it lasted only 10 minutes. Then suddenly I lost the connection to common storage to both hosts, I could see in the section maps of storage, but when I pressed update in the storage section, nothing happened and even when I tried to add it using the add storage I received the message usual "cannot read the partition table information. After being a little more careful I noticed that in the section storage cards, I could see the same vmhba34 in the two hosts with the same alias to the host of the first, and here's the strangest part, the situation I described above has been changing from time to time, which means that a few times I have seen the vmhba32 in both hosts and after some time vmhba34 in both hosts! (crazy)

  I took the big decision after playing with the partition table, without effect to use the ' vmkfstool - C vmfs3 s ' _free "_ / vmfs/devices/disks/vmhba32: 0:0:1" command

  in the second host, of course, I lost all data, but now with a simple refresh in this host, I was able to see the storage.

  Unfortunately, I still couldn't ' 1 host storage access and I published the same command "vmkfstool - C vmfs3 s"free"" / vmfs/devices/disks/vmhba34: 0:0:1 ""

  with only the change you see in bold. Accordingly, it was to see the storage after a refresh with free (1) name.

  Now he is currently working for 2 days with this way not recommended and what I would be really grateful if could help me clarify what exactly is happening.

  My main problem is that I am in front of a very unstable environment that might as well have the same unexpected problem in the future and I can't reformat always storage and loss of all virtual machines

  I tried to describe the best I could to this strange situation!

  Thank you for your time and any help or advice would be most welcome!

  I was looking for a similar solution. Seems to be the only iSCSI host is possible on freeNas. See here: http://apps.sourceforge.net/phpbb/freenas/viewtopic.php?f=53&t=403&sid=f4881e6e25e752e6ee8c6b0eae5887d3

  The only solution for learning seems to be to install the server ESX or ESXi in a virtual machine and then use iSCSI. Vm Instructions to complete the installation here (you must all PDFs 6) http://knowledge.xtravirt.com/white-papers/esx-3x.html or you can replace the opnefiler by the SUN's VM iSCSI. http://www.sun.com/storage/disk_systems/unified_storage/resources.jsp , you must use the vmware converter to convert the SUN's virtual to be used in ESX machine found this in a forum... but can not find more URL. I have not tried myself but, looking for just because you want to get a similar setup.

  Wolfgang

• Problem when adding a photo of fireworks in Dreamveaver

  Hello

  I am new to Adobe products, but like them a LOT.

  However, I have a problem.

  I have a picture that I dealt in Fireworks CS4: I added a vector Auto mask (gradient to transparency).

  I am now trying to export this picture so transparency is maintained but not luck. I tried gif Adaptive transparency index or transparency alpha without good result.

  When I add to Dreamweaver CS3 (using the < Img > tag) my photo, it has instead a white finish (where transparency should by).

  I wonder that if someone can point me in the right direction - any idea is appreciated.

  Thank you

  Carly

  Hello

  PZ is correct, png is the best option, but you should be forwarned that a .png format maintains 'alpha/transparency' to a bit of a cost: it is usually a MUCH larger file in download size. You assign attributes in Fireworks, experiment a bit and set the 'slice' that you want and check the differences in the size of output file to compare the difference between .gif, .jpg, and .png. If it is a single image, and small enough, I would not be too concerned, but consider the time of collective download of ALL your images and data that you create your page - it is possible to integrate your background color of your image, it would likey be a better choice to choose .jpg or .gif format, if the time to download on your page is a concern. In addition, lowest for .png file size is reduced, but will usually create a white border around the silhouette - high will make a large transparent image (including the edges soft and melted), but will generate a file size that is much more important to choose wisely as you design your page...

  Hope that helps,

  Jesse

• Problem when adding 1 GB memory of my Satellite M60-103

  My satellite, running windows XP, became too slow; He had only 512 Meg of memory so a technician added 1 gb module, which gives a total 1.5 GB of memory.
  But since then I get from time to time problems with for example, touchpad and sometimes a blue screen with large print; in other words: the satellite is functional but is not stable.
  Is it because they put too much memory? say they have o replace the existing module and not add one more?
  Thks or your help.
  I'm not a technician, so please try to answer in simple English user

  It is certainly not too because your laptop model can manage with 2 GB of RAM.
  Can you tell us what module memory 1 GB is inside (specification and brand)?
  There may be a compatibility issue.

  Compatible with 1 GB of RAM for this model of laptop ha PA3411U-1M1G part number.

• Problem when adding a sensor to IDS MC

  Hi all

  Any body has encountered the problem I'm facing here? I add 4 sensors to my MC IDS (2.2) and I get an error message when I tried to add the third argument, I clicked on (see the message) and I got the output attached... Please tell us how can I troubleshoot/fix this problem...

  Appreciate your cooperation...

  Concerning

  Regenerate the certificate of the probe. Usually, it is because the certificate of the probe has expired. Then return to IPS MC and add the sensor.

  For sensor 5.x through IDM:

  Configuration > Configuration sensor > Certificates > certificate server

  Click on generate the certificate

  For sensor 4.x through IDM:

  Device > sensor configuration > certificate > generate certificate of host

  Click on apply for sensor

• SCSI address and null field problems when adding disks

  I had a spreasheet and requires up to 6 drives to be added to a list of virtual machines.

  vmname hdd1, hdd2, hdd3, hdd4, and hdd5, hdd6. I then want to run another command if hdd2 is lets say its to return "two disc exists."

  HDD1 must always be mapped to scsi 0:3.

  HDD2 must always be mapped to scsi 0:4 etc..

  but some time ago a hdd1 and a hdd3 and hdd6 but no hdd2 or hdd 4.

  I have two problems

  I don't know how to make sure the player is assigned to writing scsi address.

  I know how to do or not to do things if the fields are null or not.

  Help, please.

  You can specify a SCSI nummer if you add a drive hard using the vSphere API:

  $spec = New-Object VMware.Vim.VirtualMachineConfigSpec
  $spec.deviceChange = New-Object VMware.Vim.VirtualDeviceConfigSpec[] (1)
  $spec.deviceChange[0] = New-Object VMware.Vim.VirtualDeviceConfigSpec
  $spec.deviceChange[0].operation = "add"
  $spec.deviceChange[0].fileOperation = "create"
  $spec.deviceChange[0].device = New-Object VMware.Vim.VirtualDisk
  $spec.deviceChange[0].device.key = -100
  $spec.deviceChange[0].device.backing = New-Object VMware.Vim.VirtualDiskFlatVer2BackingInfo
  $spec.deviceChange[0].device.backing.fileName = ""
  $spec.deviceChange[0].device.backing.diskMode = "persistent"
  $spec.deviceChange[0].device.backing.split = $false
  $spec.deviceChange[0].device.backing.writeThrough = $false
  $spec.deviceChange[0].device.backing.thinProvisioned = $false
  $spec.deviceChange[0].device.backing.eagerlyScrub = $false
  $spec.deviceChange[0].device.connectable = New-Object VMware.Vim.VirtualDeviceConnectInfo
  $spec.deviceChange[0].device.connectable.startConnected = $true
  $spec.deviceChange[0].device.connectable.allowGuestControl = $false
  $spec.deviceChange[0].device.connectable.connected = $true
  $spec.deviceChange[0].device.controllerKey = 1000
  $spec.deviceChange[0].device.unitNumber = 5
  $spec.deviceChange[0].device.capacityInKB = 1048576
  
  $vm = Get-VM -Name MyVM
  $vm.ExtensionData.ReconfigVM_Task($spec)
  

  The above code adds a hard drive with number 5 on the SCSI to a virtual machine called MyVM. The line:

  $spec.deviceChange[0].device.unitNumber = 5
  

  sets the number of SCSI to 5. A value of 0 in the number 0 SCSI: 5 is defined by the SCSI controller. So if you have a SCSI controller then the first number will always be 0.

  I don't know what you mean with "I know not how to do or not to do things if the fields are null or not.".

• problem when adding a new row to the table.

  Hello
  
  I have a table in my ADF form. and when I click on CreateInsert adds a new to the table, but the premiere. I want that all the new lines to be added at the end of the table in a sequence. How can I do this?...
  
  
  Thank you and best regards,
  Helene

  Hello

  Try this:

  DCIteratorBinding dciter;
  BindingContainer links is BindingContext.getCurrent () .getCurrentBindingsEntry ();.
  dciter = bindings.get ("findAllTestAndryIter") (DCIteratorBinding);
  ViewObjectImpl vo = dciter.getViewObject ();
  If (vo! = null)
  {

  Line = vo.createRow ();
  int rangeSize = vo.getRangeSize ();
  int rowsInRange = vo.getAllRowsInRange () .length;
  int insertPos = rowsInRange< rangesize?="" rowsinrange:="" rangesize="" -="">
  vo.insertRowAtRangeIndex (insertPos, line);
  vo.setCurrentRow (row);
  }

• Problem when adding new column on table with report form

  Hello
  
  I have a form on table (either emp) with report(select_empno,ename,job_from_emp).i have insert, update, delete operations on the table.
  
  Now I added a new column DOB for alteration report emp.i sql query to show the new column altered report.i insert process (Block anonymous plsql) to insert this column too all by creating a new row.but the problem is with update.i am not able to find how to upgrade this new column while doing the update to line level.
  
  pls let me know if you can give some ideas on this.
  
  
  Kind regards
  CK

  Well, sorry for sounding terse.

  I have a few questions.

  Have you added the item to the form page and associated with the database column?
  You use your own PL/SQL page process to update or do you use the 'row emp process' process produced auto?
  If it's your own please send the code with the word {noformat}

  {noformat} (with the curly brackets and in lower case) above and below it. Your code should be formatted like this once you've hit post message:
  

  BEGIN

  NULL;

  END;

  Cheers
  
  Ben                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    
  

• Facing a problem when adding favicon.ico on demand at apex5

  Hello

  I mentioned this blog ORACLE BRAINS: ADDING a FAVICON to APEX to add favicon. But I'm not able to change the appropriate line in the header definition in the model (filtered per page), as it cannot be changed.

  It shows as 'this model is subscribed to the matching templates in the main theme. To change this model, change the main master page and then refresh the theme. You can also create a local copy cancelled this model. Unsubscribed models can be modified and will not be overwritten by an update of the theme." " So, how can I find the main theme and change?

  Please help me on this.

  Hi ThiliBu,

  ThiliBu wrote:

  I mentioned this blog ORACLE BRAINS: ADDING a FAVICON to APEX to add favicon. But I'm not able to change the appropriate line in the header definition in the model (filtered per page), as it cannot be changed.

  It shows that "this model is subscribed to the matching templates in the main theme. To change this model, change the main master page and then refresh the theme. You can also create a local copy cancelled this model. Unsubscribed models can be modified and will not be overwritten by an update of the theme. "So, how can I find the main theme and change?

  Please help me on this.

  Using universal theme with Oracle APEX 5? If so, the blog you mentioned is suitable for older versions of Oracle APEX, with 5 APEX, you must follow the following blog to add favicon to your application.

  Reference:- APEX 5.0: Favicon customized for Applications using the universal theme | Inside Oracle APEX by Patrick Wolf

  Kind regards

  Kiran

• Problem when adding a folder of additional plugins via the preferences

  When I add an additional plugin using the plugins preferences in CS6 plugin appears in cs6 but my active tools will vibrate or vibrate around when I try to use them. If I uncheck preferences-plugins-additoonal plugins and restart the pulsation of the tools constantly.

  Anyone else run into this. No way to stop the exciting tools?

  You point the preference of plugins for plugins CS6 or a previous version of Photoshop plugins folder?

  If so, turn off this preference - you are doing more harm than good.

  If you are just pointing to a folder with third-party plugins, then most likely these plugins have some bugs that are originally "pulsed" tools.

• Problem when adding header/footer

  Hi all!

  We are chemical product design software company. Our products have the export to PDF (procedure established internally according to the specification of the public pdf format).

  One of our clients has Acrobat Pro installed and wants to add the header/footer for the pdf files generated by our software. And here the problem arises: If a particular page in this pdf file contains text data - the header is not displayed. If a page contains only graphics - everything is OK.

  I downloaded an example at http://www.multiupload.com/GE0EQ0LR5J . You can see the original file Test-head - Footer.pdf and after editing in Acrobat 8 Pro: the header appears on page 2, but not on page 1.

  Interesting fact: Acrobat Pro 6 inserts header to all pages, but 8.9 and X only on page 2.

  I broke my head trying to find why this is happening, but could not.

  Ideas, people?

  There is something very strange with the object of text on page 0 - if you run a low-level syntax of the file using tool control upstream Acrobat Pro, it will report a number of failures. You will also find that this is not a text object as an object page should (i.e. you cannot change it).

  I have not tracked down why this should cause the header/footer missed their calls to paint, but he does. I'll have a poke on but can't promise anything.