HP Color LaserJet 1600: HP Laserjet 1600

Similar Questions

• Unable to print on Windows 8 with Color Laserjet 1600

  I installed DOT4x64.msi on my new laptop HP Windows 8, since this seems to be the only average current to connect my Color Laserjet 1600. The printer will now appear in the section "Devices and Printers" Control Panel.  But when I try to print something, I get an error message that says that I can't print to the printer. I spent nearly an hour on the phone with HP support with no resolution - in fact, after all this time, I was told "this Department does not support this printer!.» Any ideas on a solution here? Thank you!

  PS - I initially posted on a different picture, I hope someone here can help.

  For this device, the driver of windows 8 will not release until the end of January. Please bookmark this site and refer to it for more information up-to-date.

  Can I 8 supported for LaserJet printers

  In the meantime, drivers windows 7 should work for this device.

  Color Laserjet 1600

• HP Color Laserjet 1600: Driver for HP Color Laserjet 1600 10 Pro 64-bit Windows

  When a driver available for the HP Color Laserjet 1600 for 10 64-bit Windows?  It printed fine with Windows 8.1, but since the updgrade Windows 10 it prints nothing.

  Thank you

  JN

  I answered my own question or find a temporary solution until the official driver is published. After a few successes and failures with different drivers HP Color Laserjet, I downloaded the driver communication USB LaserJet of HP (DOT4) of Windows 8 and higher (64-bit) , located at the link below.  It is listed for the printer HP Color LaserJet 3700 , but it worked for the HP Color Laserjet 1600 as well.  Hope it helps someone.

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=315850&swLangOid=8&swEnvOid=4192

  Thank you

  JN

• Color laserjet 1600: color laserjet 1600 Toolbox not install on win 7

  Color laserjet 1600 Toolbox not install on win 7

  Have uninstalled and rebooted and installed the complete 'solution' software & restarted and it isn't there...

  Cartridge issues are normally resolved by changing the cartridge.  It is usually not much anyone can do to fix one defective, other than frequent cleaning, cartridge until ink is exhausted.  It is often a lot of annoying for most people to bear.

  If you have isolated him down to a problem with the drum or cartridge that my suggestion is to replace it with another cartridge first and consider other options for cleaning and maintenance after.  If the Exchange with a new cartridge solved the problem, you can pursue the options of guarantee/return/refund from the supplier you bought the cartridge under whatever policy they have for defective cartridges.

• How can I set up my printer color Laserjet 1600 in "project mode" to save toner?

  HP Color Laserjet 1600.  An article in the New York Times today business section suggests that I put my printer in "project mode" to save on the use of toner.  How can I do this?

  The project is in an unexpected place: right click on the Color Laserjet 1600, printing preferences, and then click the finishing tab and put under print quality.

  

• Color LaserJet 1600: print error for Color LaserJet 1600 not solved with troubleshooting or relocation attempt

  I get an 'impression' error when trying to print any document. Have used the convenience store, who said that a print job has been blocked and that the authorized troubleshooter. Second attempt, same result. Attempt to uninstall printer but had received "implemented encountered abnormal program execution. Implementation will stop. "The next window: your printer may have been incorrectly installed, try to reinstall with the recommended settings. Got it but no change. Try "add/repair" printer with no solution. INFO: Color LaserJet 1600, PN # CB373A, Windows 7 Home Premium

  Hi Brenda6,

  When you reinstall the printer helps reinstall you by plugging the USB of the computer? Or are you downloading from the HP site? I recommend that you disconnect the printer from your computer by unplugging the USB or disconnect the connection without wire and then go to the HP support for HP Color LaserJet 1600 printer. Find your printer driver and reinstall.

  I hope this helps!

• HP Color LaserJet 1600 Laser printer does not

  After I installed Windows 7 instead of Vista on a 64-bit HP laptop, I had problems with my printer (HP Color LaserJet 1600 Laser Printer).  The test page works well, but some applications, such as the Windows Photo Viewer that comes with Windows 7, produce nothing but totally black pages when I try to print photos (it's black, not white).  The strange thing is that, if I insert a picture in a Microsoft Word 2007 page, it prints well!  In addition, other applications are unable to make use of the printer, such as Adobe Reader 9 and Adobe Photoshop Elements 7, who refuse to recognize the printer.  Is this a known issue with a solution?

  Hello

  I suggest you to follow the methods and check.

  Method 01:

  Try to run the printer Troubleshooter and check that if it helps, here is the link:
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Method 02:

  Why can I not print?

  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print

• How can I get a color from 1600 to printing on the net

  HP Color LaserJet 1600

  windows Vista operating system

  error unable to print script error

  I'm unable to print whenever I'm on the net especially when I'm in a secure site

  any help would be appreciated

  What operating system uses the computer?

  What browser is being used (for example Internet Explorer 32-bit Internet Explorer 64-bit, Firefox, etc.)?

  It seems that your problem may be related to that document of Microsoft.

• HP Color Laserjet: HP Color LaserJet - lines/stripes

  Hello

  I have a HP color LaserJet and I get a lot of lines and streaks on my printed pages.

  I also note toner inside the printer and my printer seems to take cleaning cycles more than before.

  Thank you!

  Although I work for HP, my posts are MY opinion and not those of HP.

  I would recommend some of the things

  First of all, make sure that your firmware is up-to-date, go to the page software and drivers on HP.com download and install the latest firmware available for the printer.

  Then, make sure that the toner collection unit is not complete

  Finally, print a cleaning of the control panel of the printer page, normally, you should select the following text in the menu:

  • Maintenance of the unit
  • Calibration / cleaning
  • Cleaning page

  You can also view this document as well.

  HP Color LaserJet Enterprise M552, M553 and MFP M577 - lines/stripes, toner and cleaning cycles dust excessive

  Hope that helps.

• Color LaserJet M277dw MFP: Cartridge not recognized after HP recently updated.

  I can use WIndows 10 if the fix is available for this OS.

  I recently updated my HP LaserJet, and after the update, he refused to print, scan or copy. The error message on the display says: "Cartridge not recognized" and it has a large image of the yellow and black cartridge, cyan and magenta those smaller, but below. The printer has a wireless connection to internet.

  Any help would be greatly appreciated.

  Thank you

  Hello

  Install the following firmware for your printer, and then look for a difference:

  http://support.HP.com/us-en/drivers/selfservice/swdetails/HP-Color-LaserJet-MFP-M277-series/7089945/model/7089949/swItemId/kJ-149905-2

  Kind regards

  Shlomi

• Color LaserJet MFP M477fdn Pro: M477 Software Installation fails at 99%

  Like others who have posted here, I have been unable to get the printer software to complete the installation. The printer is a Color LaserJet Pro MFP M477fdn, 3 months. I'm trying to install the software on a new workstation HP Z240 performing Windows 10 (64-bit). The connection is via USB cable. The printer and the software have been previously used with a Windows 7 machine without problem.

  I tried, repeatedly, to install the software from the disc supplied with the printer and also a 126.6 mb download HP Color LaserJet MFP printer M477 Pro series full software and drivers. The results are the same with a source - installation apparently progresses up to connect it the indicator product of progression from screen reached 99%, how it gives an error message "a Setup operation took too long to run. It is a fatal error, preventing the use of the product. Restart your computer and run this installer again. If the problem persists, please visit the web site of product support for your product. "It takes about 20 minutes for the phase of installation to go from 0 to 99%, and then later hooked up to 99% for 2-5 minutes, the error message is displayed.

  I am able to print to this printer, but at least do not have the ability to scan from the computer there is no indication that the I.R.I.S. OCR software is installed.

  I had care of do not connect USB until you are educated.

  I tried repeating the installation without uninstalling first and get the same result.

  I used the uninstall contained the disk feature, and have deleted the printer to the computer using the Panel between the installation attempts.

  I tried to do a right click to run the installer as administrator and get the same result.

  I tried to install after clean boots with turned off Windows Firewall and all functions of the software Norton Internet Security including its function of firewall turned off.

  The event viewer displays none error entry at all and no entry identifies HP as the source of an event.

  I tried to connect via USB 2.0 and 3.0 ports.

  I cleaned recycle them and temporary folders.

  I have updated the firmware of the printer to the 20160331 version.

  Printed printer configuration report will not display any errors, nor that the printer itself indicates something is wrong and confirms the update of the firmware.

  I deselected the optional software, the devices experience HP and I.R.I.S. OCR, trying to install only the required files two more program scanning HP.

  Thanks for any help solving this.

  I think I understood the question, 10 windows installs its own driver, and the installation program expects the hp driver to install.

  DO this FOR THE HP INSTALLER PROCESS (when the percentage meter goes)

  1. go into the Device Manager and find the printer in the list of devices

  2. right click on the printer and select "Update Driver software"

  3. click on "Browse my computer for driver software".

  4. choose "Let Me pick one...» »

  5. Select the named driver: HP Color LaserJet MFP M477 PCL-6 Pro (make sure it's one with a dash between the pcl and 6!)

  6. click next and back to the installation of hp box and must now see the printer and continue the installation.

  -Alex

• Color Laserjet 2550 L and XP SP3

  Hello

  I installed XP SP3, last week and since I was not able to print from my color laserjet 2550 L printer. I tried the windows troubleshooting printing suggestions for the use of different drivers, but no luck. Any body out there got any advice, it's a pain not being able to print.

  Thank you very much

  If there is no Purifier not listed on the Web site nothing listed in your programs menu or add remove software window, then all you have is a base driver installation.  Following the steps listed for remove driver and the entrance to the server properties should be sufficient.  Manual uninstallation is for printers that have utility programs or use Software Solutions of Support or Director.  Even still, following the instructions provided here should at least bring basic functionality.

• LaserJet pro 177: bought used hp color laserjet pro mfp m177

  Installation disk arived broken. How can I do to replace it.

  Just upload what you want the site web theHP.

  http://support.HP.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-M177-series/5303438/model/5303443

• HP Color LaserJet 4550: HP Color LaserJet 4550 PCL XL error

  I use this printer for years.  It works beautifully.

  Windows 10 has just done an update & the printer driver disappeared.  I use this printer with a HP Jet Direct J4135A usb card.  Now any driver or what I do I try to install or use, I get the same error message.

  I am trying to use the printer driver's upd-pcl6 - x 64 - 6.3.0.21178.exe.  The printer driver appears in the settings & is by default we & they say that everything works correctly.

  Can you help me please?  I don't want to go out and buy another printer.

  PCL XL error

  Subsystem: KERNEL

  Error: UnsupportedProtocol

  Operator: 0x0

  Position: 0

  Found the solution for everyone that might have this problem.

  Just right click on the printer icon in the Device Manager and select printer properties / Advanced / change & driver driver HP Color LaserJet 4550 PCL6 ranking to HP Color LaserJet 4550 PCL6 and click OK.  That's all there is to it.

  Now, it will work with USB (HP Jet Direct J4135A Card) that is not supported, instead of just supported network.

• HP Color LaserJet Pro M177 MFP: HP Color LaserJet not able to connect to connected HP

  Hello

  I try to activate my printer (HP Color LaserJet M177fw MFP Pro) ePrint and much more, but I'm not able to do it cause connection problem, I guess.

  When I'm trying to 'print the information sheet', for example, the printer is not able to connect (stay on 'Sign in' loop indefinitely).

  My printer is less than a Vodafone EasyBox router, with firewall disabled and no specific barriers defined by me.

  Should I set some port forwarding (even if they should apply to ignore the firewall, when turned on) or any other specific configuration in the router?

  the same connection problem, of course, it happens when I do touch printer and console web administration, of course.

  In addition, I'll let you know that my router is not blocking access, for example, to-from the web (i.e. I am able to manage my NAS from the outside, since he admitted to a DDNS) and other local devices

  I alreay set 8.8.8.8 and 8.8.4.4 as DNS pri/sec and had an output of cycle after the series of DNS.

  My printer also has a static IP address (defined by the DHCP protocol, based on the MAC address), so not a problem, I think.

  Thanks in advance for your help,

  Lorenzo

  Hi Lorenzo,.

  To enable Web Services fumctionality, you'll need to install the latest firmware on your printer (version 20160525)

  You can locate the current version of your printer by selecting configuration > reports > Page of Configuration, the firmware version is listed under the information section on the printer.

  Updated the firmware on Linux by following these steps, but I don't know if the latest firmware is available for Linux or not, try:

  http://hplipopensource.com/hplip-Web/tech_docs/man_pages/firmware.html

  If the latest firmware is not available for linux, temporarily install the printer on a Windows PC or a my and install the latest firmware:

  http://support.HP.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-M177-series/5303438/model/5303443

  Kind regards

  Shlomi

• HP Color Laserjet M277dw MFP: Cannot scan HP Color Laserjet MFP M277dw on Mac OS 10.6

  Hello, I can not scan to network drive using the above mentioned printer. Scan to USB key is possible.

  I downloaded the update (version 20160331) firmware image, but impossible to install the program. After double click, nothing happens. Any ideas?

  Thank you and best regards

  Christoph

  Hi Christoph,

  The printer is not compatible with Snow Leopard, it is supported on Lion (10.7) or later versions.

  You can find the system requirements below:

  http://support.HP.com/us-en/product/HP-Color-LaserJet-Pro-MFP-M277-series/7089945/model/7089949/document/c04515051/

  The update of the firmware utilitywas not desinged for your operating system and therefore does not work on it.

  As the connectewd printer to a network, follow these steps to update firmware directly from the menu of the printer:

  http://support.HP.com/us-en/product/HP-Color-LaserJet-MFP-M277-series/7089945/model/7089949/document/c04517106/

  If the implementation of scan to a shared folder on your grave down Mac, please specify the exact error, and the parameters used (path of the shared folder used, etc.) also well done you have shared this folder your Mac form?