Problems with digital photographs.

Similar Questions

• Error Message - Windows Media Player cannot play this DVD because there is a problem with digital copy protection

  I received the following message when trying to play a DVD:Windows Media Player cannot play this DVD because there is a problem with the digital copy between your DVD drive decoder and video card protection. Try to install a driver available for your video card. I'm confused that nothing has been changed, added, or updated my system up-to-date. I am running Windows 7 Premium home 64-bit edition. DVD plays fine on my laptop with the same operating system.

  CORRECTION OF THE PROBLEM.

  I can confirm that it is a matter of the DVD CSS protection. MediaPlayer, being unable to decrypt the DVD protection.

  Googled around for "DVD43". The installation program will install a driver that will successfully decrypt DVD protection and will allow you to PLAY the DVD MOVIE ONCE AGAIN!

  Well, that's an alternative. All what I can say is that Microsoft Media Player is broken!

• Problem with digital I/o read and write in CVI

  I have a PXI with PXI 6225 Renault installed box. For some uses, I wired 4 lines of digital port 0

  for its 4 top lines so that the output digital on bottom lines can be read as a digital input on the top lines.

  In the CVI program I have set up two input and output of tasks as follows:

  Enter task:

  DAQmxCreateDIChan (digitalInputTask, "PXI1Slot5/port0 / line4:7","InputLines", DAQmx_Val_ChanForAllLines ");

  DAQmxCfgSampClkTiming (digitalInputTask, ' AI/SampleClock ", 4000, DAQmx_Val_Rising, DAQmx_Val_ContSamps, 2000" ");

  Output task:

  DAQmxCreateDOChan (digitalOutputTask, "PXI1Slot5/port0 / line0:3","OutputLines", DAQmx_Val_ChanForAllLines ");

  DAQmxCfgSampClkTiming(digitalOutputTask,"ai/SampleClock", 4000, DAQmx_Val_Rising,DAQmx_Val_ContSamps, 2000));

  DAQmxCfgOutputBuffer (digitalOutputTask, 2000);

  I also started a task of analog input to ensure that the analog "IA/SampleClock" sample clock is running, and I check

  as I interpret the correct analog data of my analog lines.

  Here's the problem:

  I write 2000 identical samples of zero for the 4 lines (port0/$line0... (3) with the following command:

  DAQmxWriteDigitalU32 (digitalOutputTask, 2000, 1, 10, DAQmx_Val_GroupByChannel, sampleArray, & writing, NULL);

  After a while, I try to read the 4 lines (port0/4... (7) using the:

  DAQmxReadDigitalU32 (digitalInputTask, 2000, 10, DAQmx_Val_GroupByChannel, scanArray, 2000, & read_num, NULL);

  but the values returned in scanArray are nil!

  If I replace the digitalInputTask by digitalOutputTask in the above function call, I get the good samples rewritten

  (do not know how the 4 lines below that are configured in output mode can be read back! could it be just read buffer?)

  I don't know that the hardware configuration is correct, because when I try to emulate this feature in Labview, it works.

  (I use an output data acquisition assistant to write down the 4 lines of port 0, using a digital wave of entry, then)

  top reading 4 lines with the help of one Assistant DAQ to enter a digital waveform VI.

  In another test, I have 4 lines below in CVI, put on stop my CVI program, start a simple Labview VI to read from

  upper 4 lines and I can see the values I just write in CVI).

  Any idea what could be causing DAQmxReadDigitalU32 to read only zeros in CVI?

  I compared my settings in CVI with parameters DAQ assistant in Labview and tried to make them identical, but nothing helped.

  Thank you

  Try to use these examples to see if you can read and write in CVI

• Problem with digital certificates

  Has anyone met with this error before?
  We bought a Verisign certificate and used to get our certificate TP. I then imported the Cert TP as Trusted Cert in the Oracle default B2B portfolio. I have the Verisign Cert purchased as user certificate
  Then I configured the B2B configurations to use the secure channel but I get the following.
  -Codean
  
  2008.10.08 to 21:48:37:058: Thread-10: B2B - java.security.cert.CertificateParsingException (ERROR): signed overflow, bytes = 67
  at sun.security.x509.X509CertImpl.parse(X509CertImpl.java:1662)
  to sun.security.x509.X509CertImpl. < init > (X509CertImpl.java:173)
  at sun.security.provider.X509Factory.engineGenerateCertificate(X509Factory.java:90)
  at java.security.cert.CertificateFactory.generateCertificate(CertificateFactory.java:389)
  at oracle.tip.adapter.b2b.utility.Utility.getX509Certificate(Utility.java:1743)
  at oracle.tip.adapter.b2b.packaging.SmimeSecureMessaging.sign(SmimeSecureMessaging.java:961)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.createSignedMimeBodyPart(MimePackaging.java:392)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.applySecurity(MimePackaging.java:1699)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.createMimeMessage(MimePackaging.java:262)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.pack(MimePackaging.java:110)
  at oracle.tip.adapter.b2b.msgproc.Request.outgoingRequestPostColab(Request.java:1165)
  at oracle.tip.adapter.b2b.msgproc.Request.outgoingRequest(Request.java:701)
  at oracle.tip.adapter.b2b.engine.Engine.processOutgoingMessage(Engine.java:832)
  at oracle.tip.adapter.b2b.data.MsgListener.onMessage (MsgListener.java:531)
  at oracle.tip.adapter.b2b.data.MsgListener.run (MsgListener.java:344)
  at java.lang.Thread.run(Thread.java:534)
  
  2008.10.08 to 21:48:37:059: Thread-10: B2B - Error (ERROR) -: AIP-51083: general failure create S/MIME digital signature: java.security.cert.CertificateParsingException: signed overflow, bytes = 67
  at oracle.tip.adapter.b2b.packaging.SmimeSecureMessaging.sign(SmimeSecureMessaging.java:1054)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.createSignedMimeBodyPart(MimePackaging.java:392)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.applySecurity(MimePackaging.java:1699)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.createMimeMessage(MimePackaging.java:262)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.pack(MimePackaging.java:110)
  at oracle.tip.adapter.b2b.msgproc.Request.outgoingRequestPostColab(Request.java:1165)
  at oracle.tip.adapter.b2b.msgproc.Request.outgoingRequest(Request.java:701)
  at oracle.tip.adapter.b2b.engine.Engine.processOutgoingMessage(Engine.java:832)
  at oracle.tip.adapter.b2b.data.MsgListener.onMessage (MsgListener.java:531)
  at oracle.tip.adapter.b2b.data.MsgListener.run (MsgListener.java:344)
  at java.lang.Thread.run(Thread.java:534)
  Caused by: java.security.cert.CertificateParsingException: signed overflow, bytes = 67
  at sun.security.x509.X509CertImpl.parse(X509CertImpl.java:1662)
  to sun.security.x509.X509CertImpl. < init > (X509CertImpl.java:173)
  at sun.security.provider.X509Factory.engineGenerateCertificate(X509Factory.java:90)
  at java.security.cert.CertificateFactory.generateCertificate(CertificateFactory.java:389)
  at oracle.tip.adapter.b2b.utility.Utility.getX509Certificate(Utility.java:1743)
  at oracle.tip.adapter.b2b.packaging.SmimeSecureMessaging.sign(SmimeSecureMessaging.java:961)
  ... more than 10
  
  2008.10.08 to 21:48:37:060: Thread-10: B2B - Error (ERROR) -: AIP-51083: general failure create S/MIME digital signature
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.createSignedMimeBodyPart(MimePackaging.java:434)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.applySecurity(MimePackaging.java:1699)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.createMimeMessage(MimePackaging.java:262)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.pack(MimePackaging.java:110)
  at oracle.tip.adapter.b2b.msgproc.Request.outgoingRequestPostColab(Request.java:1165)
  at oracle.tip.adapter.b2b.msgproc.Request.outgoingRequest(Request.java:701)
  at oracle.tip.adapter.b2b.engine.Engine.processOutgoingMessage(Engine.java:832)
  at oracle.tip.adapter.b2b.data.MsgListener.onMessage (MsgListener.java:531)
  at oracle.tip.adapter.b2b.data.MsgListener.run (MsgListener.java:344)
  at java.lang.Thread.run(Thread.java:534)
  
  2008.10.08 to 21:48:37:060: Thread-10: B2B - Error (ERROR) -: AIP-51083: general failure create S/MIME digital signature: error -: AIP-51083: general failure create S/MIME digital signature: java.security.cert.CertificateParsingException: signed overflow, bytes = 67
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.createSignedMimeBodyPart(MimePackaging.java:434)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.applySecurity(MimePackaging.java:1699)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.createMimeMessage(MimePackaging.java:262)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.pack(MimePackaging.java:110)
  at oracle.tip.adapter.b2b.msgproc.Request.outgoingRequestPostColab(Request.java:1165)
  at oracle.tip.adapter.b2b.msgproc.Request.outgoingRequest(Request.java:701)
  at oracle.tip.adapter.b2b.engine.Engine.processOutgoingMessage(Engine.java:832)
  at oracle.tip.adapter.b2b.data.MsgListener.onMessage (MsgListener.java:531)
  at oracle.tip.adapter.b2b.data.MsgListener.run (MsgListener.java:344)
  at java.lang.Thread.run(Thread.java:534)
  Caused by: error -: AIP-51083: general failure create S/MIME digital signature: java.security.cert.CertificateParsingException: signed overflow, bytes = 67
  at oracle.tip.adapter.b2b.packaging.SmimeSecureMessaging.sign(SmimeSecureMessaging.java:1054)
  at oracle.tip.adapter.b2b.packaging.mime.MimePackaging.createSignedMimeBodyPart(MimePackaging.java:392)
  ... 9 more
  Caused by: java.security.cert.CertificateParsingException: signed overflow, bytes = 67
  at sun.security.x509.X509CertImpl.parse(X509CertImpl.java:1662)
  to sun.security.x509.X509CertImpl. < init > (X509CertImpl.java:173)
  at sun.security.provider.X509Factory.engineGenerateCertificate(X509Factory.java:90)
  at java.security.cert.CertificateFactory.generateCertificate(CertificateFactory.java:389)
  at oracle.tip.adapter.b2b.utility.Utility.getX509Certificate(Utility.java:1743)
  at oracle.tip.adapter.b2b.packaging.SmimeSecureMessaging.sign(SmimeSecureMessaging.java:961)
  ... more than 10

  As discussed, make sure it is valid cert from the perspective of the expiry.

• on my PC, I get the message "cannot play a DVD because there is problem with digital copy protection.

  Windows media player cannot regarderTHIS DVD because there is a protection problemwith against digital copying between your DVD drive, decoder, and video card.

  fixed by downloading updated decoder, works very well. Thanks to those who have passed on to my inquiry.

• Problems with Benq DC C 700 digital camera on the Satellite L30 105

  Hello

  I have problems with my digital camera when I connect it to my laptop. Whenever I connect the camera to the laptop freezes and gives me the blue screen of death, in other words, the screen you get when a fatal error occurs, and then my laptop must be restarted. If this happens whenever I connect the two.

  I tried the bios update and install the latest orders, but nothing seemed to work. I contacted the support center in Benq and they told me to contact Toshiba as they are sure that the problem is not with the camera. So please someone, if you have any ideas or suggestions or solutions, I'll be happy to hear.

  Thank you!

  Hello

  First of all if you need Toshiba support, you will need to contact Toshiba authorized service partner in your country. This forum here is only a forum for users and you won't find anyone from Toshiba here.

  On the other hand;
  It seems that the Satellite L30-105 has been bundled with Vista. Using this operating system on the L30?
  I read on many problems with the 3rd devices, software, and Windows Vista.

  I put t know what said you, but eventually the software webcam is not 100% compatible with Vista.
  You should know that the BSOD appears if there is a serious hardware problem or software. I don t think that this problem was caused by a hardware issue and so there is only one possibility; software compatibility issues.

  In case you I would update the Vista of the State and I will ask manufacturing webcam if it s 100% compatible with Vista.

  Good luck

• Problems with the digital input/output

  Hello

  I have a little problem with my card PCI-6143. I would use two connectors digital one as a starter and one as an output. Now, I have the problem that I do not know how I address them. The input works as I want but not the output.

  As an example. I call my channel output on this name: Dev1/port0 / line0:0.
  With this call, the application works very well. If I change the output channel to Dev1/port0 / line4:0 I get an error that the values can be read and 0 and 1 are valid values.
  I hope that the call is right, I wrote that out of my head.

  My questions are. Is it correct to call a single digital channel with this name?
  I'm not sure because I do not understand what these means 'line' and if I allocate really single channel or more.
  The second question is, can someone give me an example of how I assign two digital channels (how to address them)?
  I know it's maybe an easy question, but I can't seem to get it corrected.

  Hope someone can help me.

  Best regards

  The syntax that you use is intended to select several channels: the numbers are the initial and final channel in a subsequent channel list. Thus, written Dev1\port0\line0:4 means 5 lines are included in the read/write (FWIW written 4:0 has the same effect). It is redundant but good writing line0:0, which means a single line, but you can write to Dev1\port0\line0 which is simpler.

  This is a help page on this topic.

• Problem with the digital signatures of workers govt

  If I get emails quite frequently NAVAIRSYSCOM workers via my e-mail from work which is the right company, no Government excuseraient. On my last phone an orginal Droid, a few emaisl would tell me there was a problem with the digital signature for e-mails, but I always saw the e-mail itself.

  Since switching to the Maxx HD, I can see no longer the body of emaisl to these people. All I get is a "impossible to decrypt this message." It is not every person govt, but enough that it is very frustrating. Any ideas on how to work around this problem? and I know that the message is not encrypted, I can see fine by Exchange and we are app.

  We have a couple of our team focuses on similar issues. Passing this along.

• Error - Windows Media Player cannot play this DVD because there is a problem with the digital copy between your DVD drive decoder and video card protection. Cannot read any DVD.

  Original title: unable to play any DVD

  "Windows Media Player cannot play this DVD because there is a problem with the digital copy between your DVD player and the video card protection decoder. Try to install a driver available for your video card.

  I tried to update all the drivers but the problem persists

  Hi Neil,

  1. have you made any hardware changes or software on the computer before this problem?

  2. what version of windows Media Player do you use?

  You can follow this link & check if the problem persists.

  Windows Media Player Error Message help

  
  Reference: How to troubleshoot issues that occur when you play a DVD in Windows XP?

  Hope the helps of information.
  Please post back and we do know.

• Problem with HP Premium Digital Headset (XA490AA)

  Hi, I bought very recently (a week back) a HP Premium Digital Headset (XA490AA) and it seems to work perfectly and has a great sound, but he had a problem. The right side of the headset, for no reason, will stop working then start working. For example, I'll use my computer for maybe a few hours to a full day, and then the right side will stop working. Then he started working as if by magic somehow.

  I remember the first day I bought it, there was a bit of a problem of balance. For some reason, kept her moving completely to the right, leaving the soft left.

  I have it plugged into different USB ports, but the problem persists.

  I search online and it seems that so far I'm the only one having this problem, and I would rather go back to where I bought it if I can solve the problem.

  I got a Logitech USB Headset, prior to that, and it worked fine.

  I use Windows 7 x 64 on a HP Pavilion Slimline.

  Malcharion, welcome to the forum.

  You did a great job of explaining your problem!  However, my search proved unsuccessful, too.  I guess that you are alone in this. Which tells me, is that there must be a problem with the headphones.  If it was one of the USB 2.0 ports, they would work in one of the other.  If there was a problem with the operating system, probably someone else would be to have a kind of problem; may not be the same as yours.

  You said that you do not want to go back to the dealer, but this may be your only choice.  If a new pair did the same thing, you know that the problem is in your system.  Please let us know if you get a new pair and how they work.  Just use this thread.

• My laptop is windows 7 and with most of DVD it says that there is a problem with the digital copy. I'm also having trouble changing the region

  the exact message is: "windows media player cannot play this DVD because there is a problem with the digital copy between your DVD drive decoder and video card protection. Try to install a driver available for your video card. When I click close it comes with this another message saying that my DVD system is set to the region one and I need to change it to region 2. I have change for the region, but he said: "Windows Media Player cannot play the DVD because the disc prohibits playback in your region of the world. You must obtain a disc that is intended for your geographic region. ». I don't know what to do.

  There is a chance that the free VLC Media Player
  would be to read your DVD without changing the region code.

  (FWIW... it's always a good idea to create a system)
  Restore point before installing software or updates)

  VLC Media Player
  http://www.filehippo.com/download_vlc/
  (works on XP/Vista/7)

• Problems with WRT54GS and EasyLink after the addition of the Comcast Digital phone.

  I had a working network. Cable modem (Comcast), WRT54GS, 2 PCs per (an XP/SP3, a Vista Home Edition SP1), 2 cable PC laptop wireless (an XP/SP3, a Vista Home Edition SP1) and a HP OfficeJet 7210 printer (connected to WRT54GS as a network printer). Everything was going well and worked.

  Then, I added the Comcast Digital phone. Obviously, they went for a new modem cable modem cable with the phone service option. Now I can't print to the wired Vista PC OfficeJet and EasyLink displays "initializing" for too long I'll wait (5 minutes).

  Finally, I must kill EasyLink from the Task Manager. Any help or ideas appreciated!

  I solved the problem. It turns out the new modem cable and problem with EasyLink initialization were 'diversion '.

  The problem turns out to be a classic network problem! The Vista PC wired had a wrong IP address. The wireless PC XP has the printer configured with the name of network instead of the network address (IP, for example).

  When I deleted the printer on the Vista PC and added to the correct address everything worked fine.

  Apparently, the printer got a new IP address of the server on the WRT54GS after installing the new modem. In addition, it seems that Vista doesn't has not report an error of communication to a network printer, but for a direct USB connect.

• Problem with the Microsoft Digital Sound 80 (DSS80)

  I never had a problem with the DSS80 until recently. If I try to adjust the volume, it it cranks up to 100, and if I cut it 'restores the sound"itself.

  It can work without any problems sometimes, but all of a sudden, he turn the volume to 100. Particularly annoying when watching a movie or listening to music.
  Anyone experienced the same thing, know what causes it to this or have a solution?
  Happy for everything responds :)

  Hi Ayman,

  You might want to take a look at the article to resolve the problem,

  DSS80: How to solve the system of Microsoft Digital Sound 80

  http://support.Microsoft.com/kb/217190

  You can also see the following article for more information:

  Digital Sound System: Windows cannot detect the DSS80 speakers

  http://support.Microsoft.com/kb/220821

   

  Hope this information helps. Please come back for any clarification on this or any issue of Windows. We will be happy to help you.

• will not play DVD-problem with protection against digital copying between DVD drive decoder and map - ideo

  When I inserted a movie in the DVD drive and open Windows Media Center and clicked "play DVD" a popped up message: Windows Media Player cannot play this DVD because there is a problem with the digital copy between your DVD drive decoder and video card protection. Try to install a driver available for your video card. How can I do this?

  Hi Carol,.

  Thanks for choosing Microsoft Community!

  According to the description of the problem, you have problems playing a DVD with Windows Media Player?

  Please answer these questions to better understand the issue and help you.

  1. using Windows Media Player or Windows media center?

  2. is the specific question about a DVD?

  Follow the methods mentioned below:

  Method 1: refer to the article mentioned below:

  The Player Windows Media DRM: frequently asked questions:

  http://Windows.Microsoft.com/en-us/Windows7/Windows-Media-Player-DRM-frequently-asked-questions

  Method 2: Uninstall and reinstall the video card drivers and see if this is useful:

  Follow the steps mentioned below:

  (a) click Start, right click on computer.

  (b) click on properties, click on Device Manager

  (c) expand the graphics card, right click on the adapter option

  (d) click on uninstall

  (e) now go to your computer/device manufacturer site, download the updated drivers and install them.

  See the article:

  Updated a hardware driver that is not working properly:

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Hope the helps of information. Don't answer if you need assistance, we will be happy to help you.

• I can't play DVDs in Windows Media Player 12 on Windows 7 Pro and get this error msg: Windows Media Player cannot play this DVD because there is a problem with the digital copy between your DVD drive decoder and video card protection.

  Hello, thanks for reading and helping me.

  I try to play a legitimate, belonging to DVD, but Windows Media Player 12 will not play on my computer Windows 7 Professional.  The DVD worked a few days ago, but all of a sudden, I get the following error message:

  "Windows Media Player cannot play this DVD because there is a problem with the digital copy between your DVD player and the video card protection decoder. Try to install a driver available for your video card.

  I did a lot of research of these forums and on the ' net.  Here are the suggested steps I tried without success:

  • I tried VLC player.  This works.  However, rather than use this workaround, I wish to find a solution to my problem WMP/WMC.
  • I tried several DVD for years over the last decade.  These DVD works on my laptop, also running Windows 7 Professional and the shark 007 codec.
  • I uninstalled my Shark 007 codec
  • I tried other codecs (K-Lite)
  • I assured that the latest drivers are installed on my video card, XFX ATI Radeon 5850
  • I tried to uninstall Nero 9
  • I tried to use the Windows 7 troubleshooting options:
  • > Reading and burning CD, DVD and Blu - ray (no problem)
  • > Windows Media Player DVD (no problem)
  • > Windows Media Player Settings (detects a problem, wants to restore factory settings, every time, no matter what happens)
  • A system restore to a time when the DVD was working did not resolve the issue
  • The different links in Microsoft, I found in this forum about this problem do not seem to be useful.  There is a link that points to the set-top boxes, but this page just says: "Windows 7 comes with a decoder.
  • I assured the latest driver is available by going to "Device Manager", right click on the drive, then click on "update driver software".
  • I assured that the latest firmware is installed directly from the manufacturer's website.
  • I tried to reset my DRM by renaming the DRM under C:\ProgramData\Microsoft\Windows folder and by going to this Web site to upgrade:http://drmlicense.one.microsoft.com/Indivsite/en/indivit.asp?force=1
  • I've uninstalled and reinstalled Windows Media Player 12 and Windows Media Center via the function "functionality in Windows.

  I would be very grateful if a Microsoft technology could chime.  Thanks for your help!

  MY COMPUTER:
  DVD drive: TSSTcorp CDDVDW SH-S203N ATA Device (Samsung)
  Driver: Microsoft 6.1.7600.16384, dated 06/21/2006
  Graphics card: XFX ATI Radeon 5850 Black
  Motherboard: Gigabyte GA-X58A-UD3R
  Processor: Intel i7-920

  -Intel i7-920, Corsair 6 GB of RAM, ATI Radeon HD 5850, Gigabyte GA-X58A-UD3R, Corsair 800 d case

  Hello

  Try this free program:

  http://www.DVDFab.com/passkey-Lite.htm

  Carlos