Similar Questions

• Problem with PCI-6704 after upgrade

  I recently upgraded from labview 7.1 to 8.6, at the same time I've upgraded to the latest version of the driver NOR-DAQmx, MAX and the existing drivers (7.4.4). After upgrading my PCI-6704 Board has stopped working. When I try to run the test panels I get a message "the device is not the test. Do you want to continue? "If I click on Yes, the test Panel opens and I get the message error in 10461. I tried to reinstall both daqmx drivers existing. I tried to uninstall both drivers and remove cards, restarting the computer, and then reinstall the new. I tried to install only the existing drivers and I get the same error. The pilots reset has no effect. I also tried switching PCI slots. I have a card PCI-MIO-16-1 and it works very well, and it works in a pci slot. Is there anything else I can try?

  I uninstalled the NOR-DAQ traditional 7.4.4 and installed instead of NOR-traditional DAQ 7.1 and everything works well again. Apparently there is something in the 7.4.4 update that did not like the PCI-6704.

• Problem with the rules after upgrade of the VM in foglight cartridge

  Hello

  There is a small problem with the rules after that I updated the VM cartridge level.

  In the default rules, I changed a few settings so that they will act as I need.

  However, each time I upgrade VM cartridge my rules are off and marked as backup.

  The question is: is there a way to upgrade the cartridge and keep my active rules after upgrading?

  Best regards

  Victor

  This is the normal behavior according to this KB article

  https://support.quest.com/SolutionDetail.aspx?ID=SOL105872&PR=Foglight

  105872 knowledge article

   
  • return

  • Title

    Backup rules fill in the dashboard management rule after Foglight upgraded

  • Description

    After that an upgrade of Foglight was conducted, several backup rules are created for rules that have been published before the upgrade. For example:

    Cluster VMW IO network
    Cluster VMW IO network (backup)

  • Resolution

    During the upgrade procedure, the FMS has detected that some of the original rules have been changed in some way. It copies the rules previously upgraded in backups, before trying to merge the contents of the update rule in the former.

    Assuming that the FMS works as expected, the rules of backup can be deleted. However, it is best to confirm this in the respect of the rules first before making deletions.

    When editing rules, particularly rules OOTB (out of the box), it is recommended to copy the original rule, disable the original rule and edit the copied rule. This should reduce the risk of the problem described in this Article.

  Golan

• Problem with desktop/taskbar after upgrading Fusion 4 to 6 - Windows 7 VM

  I got a few problems after upgrading to Fusion 4 to 6 with my Win 7 x 64 bit VM Fusion. I use a Mac Pro with the Mavericks. While I managed to resolve most of the issues with a manual installation of the VMWare Tools and reconstruction/reactivate a certain number of broken programs, there is suddenly a new which is serious enough. My office is not displayed, nor is my bar of the shortcut icons for the launch of the program tasks. I can access my desktop to the user manually folder and all the "stuff" is there. " If I run a program from the icon appears in the taskbar, but it cannot be pinned. When I access more nothing, I get this popup (see image). I'm sure that's the issue. Anyond can suggest a solution, please?

  Hello

  The network error is gone I hope?

  You have to set up folders mirrored under sharing with OS X? (Menu-> Virtual Machine-> settings-> sharing-> mirrored folders). If you use mirrored folders there, then what happens if you turn off this feature to test and see?

  I don't use this feature myself, but imagine that allowing a case mirrored for Office could eventually hide something on the side of windows.

  --

  Wil

• Not able to scan with the preview after upgrade from Mac OS Sierra...

  After upgrading to Mac OS Sierra. I'm unable to use the preview to scan.  Before this upgrade, it worked fine.  The HP scanner software does NOT work something like OS 10.8 or 10.9.  Preview worked perfectly so far.  If anyone knows how to solve this problem, your contribution will be greatly appreciated.  Thanks in advance.

  Have you tried scanning with Capture of Image instead? It worked for me.

• Problem with the touchpad after upgrade to Windows Vista

  After that I've upgraded to windows vista I had problem with the touchpad, that I'm not?

  Can U help me!

  Maybe when you tell us what model of laptop you have. ;)

• Satellite 1905 - problem with the touchpad after awakening from Hibernation/standby

  Greetings.

  I've known a few interesting problems with my Satellite 1905 - S301.
  Whenever he wakes up from hibernation/standby my touchpad stopped accepting "taps" as a click on the left button of the mouse. It works normally with finger motion detection, but stops at all but it is quite annoying to restart the machine whenever he returns from hibernation mode.

  I've done a small workaround and after I close the laptop lid still works but this isn't the way it should work, I would have preferred that she either Hibernate than running for 10 hours without any sense;).

  Can someone give me the solution to this problem, please?
  Thank you in advance.

  Kind regards
  Akar

  Hello

  I agree with you. It s very boring to restart the machine each time to use the touchpad.
  This problem appears on the first day?

  I think there might be a software problem and, possibly, the new installation of operating system recovery CD Toshiba could help.
  I know, the complete installation is not the best solution, but it might help.

  You should also check you the touchpad. Satellite 1905 - S301 was designed for the U.S. market and so I checked the American website for available drivers.
  It seems that 5.3.203.2 is a newer version of the Alps touchpad driver for Windows XP.

  I suggest to reinstall the touchpad driver and check if there is no improvement.

• Anyone having problems with WiFi connectivity after upgrade to Sierra?

  I was wondering if anyone else knows issues with WiFi connectivity since the upgrade to Sierra 10.12? I have not had any problems with connectivity WiFi previously on El Capitan. Now I have regular randomly loose connectivity. My internet is cable and when it is connected I have a 100% connection. My details of iMac and I have used only 10% of my storage.

  

  No problem with my iphone 6.

  Hello AspDesigns,

  I understand that, since the upgrade to Mac OS Sierra, your Mac seems to have trouble staying connected to Wi - Fi. Fortunately the diagnosis built-in wireless can help identify the source of so much trouble.

  Search for Wi - Fi using your Mac problems

  See you soon!

• Problem with the smilies after upgrade to 7.23.0.4

  After the upgrade to 7.23.0.4 new Skype smileys (as (bhangra), (rabbit), (red) etc.) are not displayed in cats but only the words in brackets instead of them.

  Please, continue to release new versions with bugs!

  After upgrade to 7.23.0.105 all the smileys are displayed well.

  Even without disconnection/connection.

  Thank you!

• Problem with fs_clone adoption after upgrade to R12.2.3 on the instance of SCREWS

  I installed instance EBS R12.2.0 Vision on Oracle Linux Server version 6.5 x 86-64 with Unbreakable Enterprise Kernel Module 3 (3.8.13 - 16.2.2.el6uek.x86_64) and then updated to R12.2.3.  Everything went smoothly with the initial installation, the AD and T2K patches and the adoption patch cycle to 12.2.3 update.  I'm having a problem with the fs_clone running, which is the first step of the subsequent update of doc 1586214.1.  The other phases of the adoption ran OK see below.  Also here is the error I get and you want to know if anyone has experienced this or ideas?  I searched google and MOS but couldn't find a direct hit.  I'm new to adoption and struggling to solve it... any help would be appreciated. I ran to the stage of fs_clone once or twice but I got the same result.

  adoption-status-detail (it is the cycle of update R12.2.3).  Every step seems OK here.

  Current patch ID of Session: 4

  Name of node node Type Phase status started completed elapsed
  --------------- --------------- ----------- --------------- ------------------------------ ------------------------------ ------------
  HN-s-sb13 master PREPARE ENDED December 27, 13 09:27:31 - 05:00 27 December 13 09:55:35 - 05:00 0:28:04
  APPLY FULL 27 DECEMBER 13 10:11:53 - 05:00 27 DECEMBER 13 09:35:53 - 05:00 11:24
  FINALIZE ENDED 28 DECEMBER 13 09:28:46 - 05:00 DECEMBER 28, 13 09:29:52 - 05:00 0:01:06
  FAILOVER COMPLETED 28 DECEMBER 13 09:32:12 - 05:00 28 DECEMBER 13 10:05:35 - 05:00 0:33:23
  CLEANING ENDED 28 DECEMBER 13 10:25:22 - 05:00 28 DECEMBER 13 10:48:31 - 05:00 0:09:23

  
  Folder synchronization system used in this Patching Cycle: None
  Generate full ADOPTION status report to the location: /u01/oracle/VIS/fs_ne/EBSapps/log/status_20131229_120910/adzdshowstatus.out
  Please wait...
  Done...!

  adopted out with status = 0 (success)

  From txkADOPPreparePhaseSynchronize_Sat_Dec_28_12_40_05_2013.log:

  ---------------------------------------------------------------------------------------------

  ==========================
  SetCloneStatus() inside...
  ==========================

  Generation SQL file: /u01/oracle/VIS/fs_ne/EBSapps/log/adop/5/fs_clone_20131228_123623/VIS_hn-s-sb13/TXK_SYNC_create_Sat_Dec_28_12_40_05_2013/5_DEREGISTER-ORACLE-HOMES.sql
  SQL command: UPDATE ad_adop_session_patches SET clone_status = "cancel the REGISTRATION-ORACLE-HOMES ' WHERE State = ' no AND numero_de_bogue = 'CLONE' AND node_name = 'hn-s-sb13' AND adop_ses
  sion_id = 5;
  Run the SYSTEM command: sqlplus * @/ u01/oracle/SCREWS/fs_ne/EBSapps/log/adoption/5/fs_clone_20131228_123623/VIS_hn-s-sb13/TXK_SYNC_create_Sat_Dec_28_12_40_05_2013/5_DEREGI
  STER-ORACLE - HOMES.sql
  EXIT STATUS: 1
  SQL execution went through successfully.
  LOG FILE: / U01/ORACLE/SCREWS/FS_NE/EBSAPPS/LOG/ADOPTION/5/FS_CLONE_20131228_123623/VIS_HN-S-SB13/TXK_SYNC_CREATE_SAT_DEC_28_12_40_05_2013/5_DEREGISTER-ORACLE-HOMES. OUT.
  FATAL ERROR *.
  PROGRAM: (/ u01/oracle/VIS/fs2/EBSapps/appl/ad/12.0.0/patch/115/bin/txkADOPPreparePhaseSynchronize.pl)
  TIME: Sat Dec 28 12:42:54 2013
  FUNCTION: main::runFSCloneApply [level 1]
  ERRORMSG: /u01/oracle/VIS/fs2/EBSapps/comn/clone/bin/adclone.pl does not pass successfully.

  From adop_20131228_123623.log:

  -----------------------------------------------

  ADOPTION Session ID: 5
  Phase: fs_clone
  [BEGINNING 2013/12/28 12:39:57] fs_clone phase
  [EVENT]     [BEGINNING 2013/12/28 12:40:01] Clone BY following the steps
  [EVENT]     [BEGINNING 2013/12/28 12:40:02] Patch CLONE of the file system to perform file system
  [EVENT]     The call: /u01/oracle/VIS/fs2/EBSapps/appl/ad/12.0.0/patch/115/bin/txkADOPPreparePhaseSynchronize.pl
  [STATEMENT] Output directory: / u01/oracle/SCREWS/fs_ne/EBSapps/log/adoption/5/fs_clone_20131228_123623/VIS_hn-s-sb13
  [UNEXPECTED] Error occurred during execution of < perl /u01/oracle/VIS/fs2/EBSapps/appl/ad/12.0.0/patch/115/bin/txkADOPPreparePhaseSynchronize.pl - contextfile = / u01/oracl
  e/VIS/fs2/inst/apps/VIS_hn-s-sb13/appl/admin/VIS_hn-s-sb13.xml-patchcontextfile=/u01/oracle/VIS/fs1/inst/apps/VIS_hn-s-sb13/appl/admin/VIS_hn-s-sb13.xml - promptmsg = hide - co
  mark = off - mode = create - sessionid = 5 - timestamp = 20131228_123623 - outdir = / u01/oracle/SCREWS/fs_ne/EBSapps/log/adoption/5/fs_clone_20131228_123623/VIS_hn-s-sb13 >
  [UNEXPECTED] Error occurred while CLONE Patch File System to run file system using the command: perl /u01/oracle/VIS/fs2/EBSapps/appl/ad/12.0.0/patch/115/bin/txkADOP
  PreparePhaseSynchronize.pl-contextfile=/u01/oracle/VIS/fs2/inst/apps/VIS_hn-s-sb13/appl/admin/VIS_hn-s-sb13.xml - patchcontextfile = / u01/oracle/SCREWS/fs1/inst/apps/VIS_hn-s-sb1
  3/appl/Admin/VIS_hn-s-SB13.XML - promptmsg = hide - console = off - mode = create - sessionid = 5 - timestamp = 20131228_123623 - outdir = / u01/oracle/SCREWS/fs_ne/EBSapps/log/adoption/5/fs_clone_20
  131228_123623/VIS_hn-s-sb13 >.
  [PROCEDURE] [BEGINNING 2013/12/28 12:42:55] Check and stop Patch Server Admin
  [STATEMENT] select count (1) of ad_adop_session_patches
  where applied_file_system_base = ' / u01/oracle/SCREWS/fs2 ' and
  patch_file_system_base = ' / u01/oracle/SCREWS/fs1 "and
  numero_de_bogue IN ('CLONE', 'CONFIG_CLONE') and
  status (', 'F')

  [STATEMENT] There is a clone session waiting for/u01/oracle/SCREWS/fs1.
  [STATEMENT] Jumping to check and stop the Patch Server Admin step.
  [PROCEDURE] [END 2013/12/28 12:43:01] Check and stop Patch Server Admin
  [UNEXPECTED] fs_clone phase completed with errors/warnings. Check the log files
  [PROCEDURE] [BEGINNING 2013/12/28 12:43:03] Unlock sessions table
  [STATEMENT] SQL stmt: start
  AD_ZD_ADOP. UNLOCK_SESSIONS_TABLE('hn-s-sb13',60,2);
  end;
  >

  [PROCEDURE] [END 2013/12/28 12:43:07] Unlock sessions table
  Log file: /u01/oracle/VIS/fs_ne/EBSapps/log/adop/5/adop_20131228_123623.log

  Randy,

  Looks like you need to add more space to the directory/tmp, I see the following entries in the CLONE*.error file.

  CLONE2013-12-28_12-41-01 PM .error:

  =================================

  SEVERE: 28 December 2013 12:42:46 - ERROR - CLONE-20275 not enough space to create/tmp/CLONINGCLIENT8522798570339051663.

  SEVERE: 28 December 2013 12:42:46 - CAUSE - CLONE-20275 minimum required space was at '1 798' Mo, but only '1 737' MB was available for use.

  SEVERE: December 28, 2013 12:42:46 - ACTION - CLONE-20275, make sure that the minimum required space is available for use.

  GRAVE: 28 December 2013 12:42:46 - ERROR - CLONE-20233 restoration Middleware House for sourceid 'mwhome1@FMW_Home' failed.

  GRAVE: 28 December 2013 12:42:46 - CAUSE - CLONE-20233 an internal operation failed.

  Thank you

  Hussein

• Problems with the files after upgrade of Sierra

  Installed at Sierra 10.12 4 days ago on my 2010 IMac running Lion 10.7.5 did not a specific backup on the hard disk running on time machine assumes that the last backup should be sufficient.

  1 problem is that my 15 000 pictures present date instead of filing in the events as they have always been.

  2 mail seems lost several mailboxes that I had installed in the margin to quickly drag and drop INFO and interesting technical questions.

  3. I have a stream of photos don't drop-down after a few days, which will not go away it just keep reappears not no this that I still need it for.

  4 never used the cloud but considering buying iPad and dumping of my old Apple laptop not likely with the capacity of 128 GB.

  A year ago, Apple went from iPhoto to the new Photos app. If you have questions Photos I would re-post in this forum. Can be found the link to it by clicking on the Photos for Mac

  About your mail, try to rebuild your mailboxes and if this does not work, you may have to re-create the mailbox store that you had previously.

  On the planned purchase of an iPad, you have a question or was it just a comment?

• Problems with mail imap after upgrade of Sierra

  After the upgrade to Sierra, I can't sync my hotmail account in Mail.

  Before even the upgrade, I always had to change my account after each restart settings, as required for authentication SMTP and IMAP user name has been deleted. The same thing happens after the upgrade, but now when I enter the user name and press save I have error message say: A IMAP account already exists.  Only one IMAP account is allowed to be saved.

  Reming the account and recreate it does not help because I find myself in the same situation where the username is missing. Does anyone have any suggestions?

  

  The username field must my work email address and when I enter it and press on save, the error message comes.

  I am facing a problem as well with Mail on macOS Sierra: account sync not IMAP.

  I see that there are a lot of similar questions autour... hope they will fix soon!

  Even that when troubleshooting your...

• Have problems with the Audio after upgrade to Windows 10

  I got a free upgrade for Windows 10 option on my laptop Acer Aspire SW5-011. Everything seemed to work fine, except that I don't bother checking the audio before deleting the files Windows 8... Even if the computer thinks that the Audio drivers work very well that they are not. I have tried everything that I could find online to see if I could get any sound, but nothing has worked. I updated the drivers, kidnapped rebooted and updated the drivers, I tried to find the other acceptable drivers and other follow-up steps. "When I go to reading tab in the sound and click speakers, and then I go to the Advanced tab, the default format said, ' 16 bit, 48000 hrtz ' is grey, I can't click on it and when I try to test it says:"Cannot play testtone" It's as if something prevents me from accessing or it acts like I'm not pregnant? The speaker driver is called "Intel SSD Audio Device. The audio worked fine before downloading. Is it possible to fix my Audio, or to have access to it yet?

  Good so I had to update my post because I had to give the good news! However, that is how I am and I almost try everything and tinkering with different things. My audio works now. I went back the download Acer drivers and manual for my camera and I checked under 32-bit Windows 8, which was windows available. I installed my ID which has been deleted before when I had restarted or any number of things, I tried, and then I went in Drivers and installed the Master Installer. I made sure that I extracted all the files before proceeding with the installation. After it restarted my laptop I heard the Windows startup sound and I knew that it worked because I had no sound at all before. Not sure why it worked, but it did! I felt there was some sort of missing file or a compatibility issue, I'm just happy that the program helped master installation. http://us.acer.com/ac/en/US/content/drivers/5687;-; SW5-011 #_ga = 1.21697787.1131678756.1448199856

• Issues with the modem with XP Pro after upgrading from xp family

  I upgraded to XP Pro and cannot create a dial-up connection because this option is not available for me. I checked the Microsoft support pages and enabled dial-up as suggested by using regedit.
  Still no difference. So I guess that the modem or the modem settings are the problem. Ive tried to download the driver couldn't get one for xp pro.can someone tell me the necessary driver for xp pro

  In Control Panel, if I go to phone options and modem, I see "Toshiba Software modem AMR COM4" but, if I go into the settings of the Modem in Control Panel, I get the message that the modem is not installed correctly and I have to uninstall and reinstall. I did this several times without success.

  He drives me crazy - can anyone help?

  Hi Mikey,

  as a first step, it would be good to know which model you have.

  Then we can compare it with other models and perhaps a driver XP modem to another model fits!

  For the first time, here is therefore a standard modem installation oder.

  1. check if the modem is entered in the Device Manager
  2. check if the modem is configured and that it works?
  The Control Panel must be open and go to the phone
  options of modems and. It should be your modem!
  If it is not shown to you, then you must install the
  modem driver.
  3. double-click on modem and go to the Diagnostics. The
  modem query button queries the commandments with
  check the return signal. This will give you some additional information
  the modem works properly.
  4. then set up a standard dial-up connection to your
  provider of
  5. go in the properties of the modem (Device Manager) and the
  Check the brand in the "wait for dial tone before dialing" has NO
  been resolved!

  You can try!

  Pete Bye

• Problem with Microsoft Office, after upgrade Windows 8.1

  Simple and straight to the point.  After the upgrade to Windows 8.1 my Office Home and Student 2010 will only work for 15 minutes after the installation, and then after that the logo for Word or Excel screen rises, opens ever, not useful to insert the disc, the execution of repairs, which reuqires reboot of the system, whenever I need to use Word or Excel.  Someone please tell me there is a simple solution for this problem.

  Victorymarketin, welcome to the forum.

  Since they are two Microsoft programs, I suggest to contact MS Service customer assistance.  They always took me and running in short order.  It's always my solution when I have MS related problems.  They if anyone can solve your problem.

  If your problem is solved, please click "accept as a Solution.