Similar Questions

• Problem with the touchpad after upgrade to Windows Vista

  After that I've upgraded to windows vista I had problem with the touchpad, that I'm not?

  Can U help me!

  Maybe when you tell us what model of laptop you have. ;)

• Satellite A300-1EG: problem with the touchpad after installing Windows 7

  Hello!

  I had a problem with my touchpad since I installed Windows 7 (64-bit version) on my laptop (Toshiba) A300-1EG.

  I tried many different solutions to this problem.
  I checked the alignment of the touchpad (be it on) in the BIOS, I tried to install several drivers (on a site of Synaptics, automatically by Windows) and none of these work. Of course, I tried FN + F9 key combination.
  When I check the alignment of the touchpad in the Control Panel, everything seems fine. It is written, that "device working properly.

  I have Toshiba Software, what may be the cause of the problem?
  But I have no idea where I can find something.

  I'd appreciate any help.

  I hope to be understandable - English is not my mother tongue :) Thank you very much in advance for any ideas. :)

  Hi mate

  I'm not quite sure what problem you have but you should first try to install the necessary drivers touchpad m.
  Maybe you used the wrong driver in the past

  So Sat A300-1EG belongs to the series of PSAG4E.
  The European driver Toshiba page does not provide a special touchpad driver for Win 7 for this device.

  But I noticed that Win 7 64 bit drivers touchpad (Alps & Synaptics) for Satellite L500 PSLS3E series is released on the European driver page.
  Try both drivers Touch Pad for this device and test it!

  Welcome them

• Satellite A500 - problem with the monitor after restoration

  Hello
  I have a Satellite A500. He has a problem with the monitor for a while, when you turn it on it's all lines etc. and you can not read but once the laptop to boot completely it is fine. My problem is that I wanted to do a restore, but I couldn't because the screen problem it started so I plugged into an external monitor and perform the restore. That has worked well.

  But now the laptop recognizes any my laptop screen. When you go to view it offers no other monitor choice other than external, I used for the restoration. I downloaded the display driver but nothing has changed.
  ANY IDEAS?

  Thank you

  (I have the disks for the restoration, if that helps.)

  > There a problem with the monitor for a while, when you turn it on it's all lines etc. and you can't read
  If I understand you right you can see when laptop starts and you see Toshiba welcome screen. Is this good?
  When you enter the BIOS settings you see thise lines too?

  Later, when you see the desktop on the external monitor, you can use the FN + F5 key combination to switch between an LCD and external monitor. Please try to use it and post comments if it works or not.

  What operating system do you use?

• Tecra S1 - problems with the touchpad after update BIOS to 2.50

  Hello
  After the BIOS-update to version 2.5, the touchpad does nothing. From the docking station, the l' option option mouse PS2 works without any problem. Starting late, the touchpad no longer works. Normally - before the update - the touchpad began its work immediately after starting not rooted.
  What can I do to reactivate the touchpad?
  Juvenay clevain

  Hello

  Are you sure that your touchpad was not disabled?

  I mean the FN + F9 key combination to activate and disable the touchpad.

  This is why you should check this first.

  On the other hand a 3rd mouse driver part could affect the functionality of touchpad too.

  In my opinion, you should try to reinstall the driver for the touchpad and test it without connected part 3 mouse.

  Good luck

• Problem with the compilation after import from word

  Hi all
  
  I have a RH6 project that has built several layouts without problem. This morning I have imported a Word 2003 file and since I can't even generate my main layout (what is Microsoft HTML Help). To do this, the copy phase of the files, but all in the middle of the phase of update files I get the message "RoboHelp HTML Application has encountered a problem and needs to close. We are sorry for the inconvenience. "I have the ability to send or do not send an error report. Then, RoboHelp closes without completing the construction.
  
  Any ideas on what could be the cause or how to fix it?
  
  See you soon,.
  
  darkagn

  The imported section had a table with merged cells and you use an expression of generation when you build? If this could be the case see extracted 68 on my site. Known issue and a patch is available.

• Problem with the touchpad doesn't work is not on the computer.

  Today, I was on YouTube, listen to music, when I turned the volume up to full. My laptop (ASUS) is a VERY high - pitched shrill sound that would not stop until I turned the laptop on sleep. When I turned on the laptop back, the screeching stopped but my Touch Pad stopped working. Fortunately, I have a USB mouse which I use now. I tried following the instructions to activate the keypad, but it does not work. I restarted my computer, and that did nothing.

  Help would be GREATLY appreciated.

  (also, I had problems with this laptop in the past, involving having to solve every time turned to have internet access, but a day that goes by and now the internet accessibility works very well.)

  Hi Lucie,.

  Thanks for posting your query in Microsoft Community Forum.

  What is brand and model your computer?

  Problems with the touchpad can occur due to a number of causes, including cables that are not connected properly, lack of updates, corrupt or drivers incompatible or because of hardware problems. So, I would suggest trying the following steps and check if the problem persists.

  Method 1:

  Try to run the suite of equipment fixit and see if the problem still occurs.

  Hardware devices do not work or are not detected in Windows

  Method 2:

  See the additional steps provided in the following article.

  Mouse, touchpad and keyboard with Windows problems

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• Problem with the rules after upgrade of the VM in foglight cartridge

  Hello

  There is a small problem with the rules after that I updated the VM cartridge level.

  In the default rules, I changed a few settings so that they will act as I need.

  However, each time I upgrade VM cartridge my rules are off and marked as backup.

  The question is: is there a way to upgrade the cartridge and keep my active rules after upgrading?

  Best regards

  Victor

  This is the normal behavior according to this KB article

  https://support.quest.com/SolutionDetail.aspx?ID=SOL105872&PR=Foglight

  105872 knowledge article

   
  • return

  • Title

    Backup rules fill in the dashboard management rule after Foglight upgraded

  • Description

    After that an upgrade of Foglight was conducted, several backup rules are created for rules that have been published before the upgrade. For example:

    Cluster VMW IO network
    Cluster VMW IO network (backup)

  • Resolution

    During the upgrade procedure, the FMS has detected that some of the original rules have been changed in some way. It copies the rules previously upgraded in backups, before trying to merge the contents of the update rule in the former.

    Assuming that the FMS works as expected, the rules of backup can be deleted. However, it is best to confirm this in the respect of the rules first before making deletions.

    When editing rules, particularly rules OOTB (out of the box), it is recommended to copy the original rule, disable the original rule and edit the copied rule. This should reduce the risk of the problem described in this Article.

  Golan

• Problem with the transfer of files from the computer Windows XP to Windows 7 using Windows Easy Transfer.

  Original title: Put WET on the old computer

  When I try to use WET to transfer from old Win XP Win 7 again, I need trasfer WET to the old computer.  So I choose this option and move on to the part where it says "Select the USB flash drive where you want to save WET".  Well, in the window is the word "computer" I can't click on it, nor is the OK button light up.  What's wrong?

  Hello

  Thanks for posting in Microsoft Community!

  It seems that you have a problem with the transfer of files from the computer Windows XP to Windows 7 using Windows Easy Transfer.

  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.

  I suggest you try the procedure described in the link and check if it helps.

  Transferring files and settings: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/transferring-files-and-settings-frequently-asked-questions

  For more information, please see the links.

  Transfer files and settings from another computer
  http://Windows.Microsoft.com/en-in/Windows7/transfer-files-and-settings-from-another-computer

  Windows Easy transfer

  http://Windows.Microsoft.com/en-in/Windows7/transfer-files-and-settings-from-another-computer

  Get back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.

• Satellite A200 - problems with the AC adapter / CC

  Hello

  The problem concerns a Satellite A200 (PSAF6A-02H01N).

  Recently, there was problems with the laptop, taking several attempts to boot to Vista, it would lock up while loading or just hang and freeze just after loading Vista.
  But once it was up and the laptop running would be happy working for hours with the AC adapter is plugged in.

  The problem got worse now and the laptop will not load Vista end without crashing.
  We have now reduced the computer down to have only a problem when the power adapter is connected.
  The laptop battery will charge normally with the AC adapter is plugged in and the laptop on standby or off.

  The problem persists with the AC adapter is plugged in and the battery removed.
  The laptop will start and run perfectly with battery and no power adapter plugged. Once the AC adapter is plugged in the laptop indicates that the battery is charging and then after a few seconds it crash or freeze and the only escape is a full stop.
  The laptop will not work under the battery power for 30 minutes max.
  I checked the output voltage of the AC adapter and this seems to be a consistent 19.4 Volts.

  Is this only a problem of AC adapter or the problem with the laptop?

  Thanks in advance...

  The Canada Gazette

  I lifted the previous discussions on this problem and found one that was very similar, but unfortunately the user decided not to find the problem of the road, save money and buy a new laptop instead! Hmm. !! .. seems to me like this might be a prob. material. Maybe a new motherboard?... anyone have an idea of what are the costs for that perhaps? .. an ASP or decent technician backstreet?...

• Satellite U500 - problem with the cooling system has been detected

  I have a Toshiba Satellite U 500 series, and I just got a message saying "a problem with the cooling system has been detected. Please turn off the power immediately and return it to service.
  Before that, I would like to know if anyone has had this problem and if there is a software solution?
  HIERARCHICAL

  Check HERE to see if anyone else had this problem in the past.

• Satellite A500 - problems with the temperature of the GPU

  The thing is playing Age of Empires online I started having problems with the temperature of the GPU. When you run the AIDA64 the CPU stress test can hold up well, but after 35 minutes the test what AIDA suspended while the GPU fan can't seem to download their revolutions, (I guess that if there was that a rise in temperature would increase the speed of rotation of the fan, don't).

  I consulted the manufacturer of the GPU, nVidia, (the graphic is nVidia GeForce GT 230 M) and tell me to contact Toshiba for other options, since, according to them, the problem is not the GPU.

  Any ideas or suggestions?

  You use your laptop to factory settings?
  Have you installed something that may be responsible for this (non-Toshiba display driver)?

• ThinkPad X 230 Windows 7-64: problems with the screen after updates

  Hi all

  I have a problem with the Thinkpad X 230. After a recent update of Windows 7 (64-bit), the screen resolution is set to 800 x 600 and brightness to the minimum. FN + F8/F9 does not work. The brightness is uncontrolled. I had to restore the system before the update.

  How to solve the problem, do anyone know?

  Thank you!

  Isosik

  Hi Isosik,

  Welcome to Lenovo Community!

  According to the request, we understand that you are facing problem with the display resolution on your ThinkPad X 230.

  If you have updated the drivers from Windows update, sometimes this kind of problem occurs with windows generic drivers for cause of driver incompatibility, suggest always update drivers only via the ThinkVantage System Update utility. Update only the application of Microsoft Windows Update.

  You can also manually download the drivers from the Lenovo support site.

  Lenovo support site.

  I hope this helps.

  Best regards

  Agnes Kumar

• HP 15 laptop: problem with the touchpad and the key "stuck."

  Hello!
   
  Last weekend, I have an irritating problem with my HP 15 laptop. Bought two years ago and upgrades to Windows 10 a year ago.
   
  First of all, my touchpad started to not work properly. It "freezes" and I can't use it until I click the ESC key, but it doesn't last and "freezes" again a few seconds later. Then, everytime I open a window where there is a text box (Start menu, edge browser, Control Panel, etc.), the number 5 is entered automatically and permanently, as if the button 5 has been blocked. I did a quick check and button 5 do not seem physically stuck.
   
  Yesterday, I restored the system to the factory settings, so I'm back to 8.1 for Windows and then upgraded to Windows 10. Everything seems to work fine, but this morning, the problem was back. Is there something I can do? What is the problem caused by Windows 10 or the computer? Should I restore it to Windows 8.1? Everything worked great til last weekend, I don't know what that was.
   
  Thank you in advance for your help!

  Welcome to the HP support community @gouch3.

  I understand that you have a problem with the keyboard and the touchpad on your laptop from HP 15.

  Have you tried to use a keyboard external and mouse at all?

  Have you tried to go to Safe Mode to see if the problems persist in there?

  Have you tried to perform a material or forced reset Reset?

  Did you do a test of material?

  Have you updated your drivers?

  gouch3 wrote:

  ... Is there something I can do? What is the problem caused by Windows 10 or the computer? Should I restore it to Windows 8.1? Everything worked great til last weekend, I don't know what that was.

  It could be a driver problem to be able to look at that for you, I need your model number. I wish I could give you an answer or not, but at this point without the troubleshooting results and the model number, it is difficult for me to say.

  I can say that if everything works in point 8.1 of Windows without problem, the driver TROUBLESHOOTING is a great place to start. Please try to follow these steps for the keyboard and the touchpad of troubleshooting:

  • Beginning
  • Search for Device Manager
  • Search results, open Device Manager.
  • Click on display
  • Show hidden devices.
  • Click the arrow next to keyboards.
  • Right click on the name of the keyboard device.
  • Select uninstall.
  • Continue deleting the names of devices in the category keyboards until the feature of all the names have been uninstalled.
  • Restart the laptop twice.

  Touchpad:

  • Type of research, "Device Manager."
  • Click on Device Manager,
  • Expand mice and other pointing devices.
  • Right click on the TouchPad,
  • Click on uninstall.
  • Restart the computer laptop twice,
  • Reinstall the TouchPad card.

  I found a document of troubleshooting for you to try also called Portable keyboard troubleshooting. Please be sure to follow the steps described in this document.

  The best document I have for TouchPad problems is the use and troubleshooting of the TouchPad and ClickPad document. 

  Here is a link to the HP Support Assistant, if you need it. Just download and run the application and it will help with the software and drivers that need to put up-to-date.

  This is a great question other clients may also be questioned. When we came to a resolution, please share what has worked for you with others by marking this post as an acceptable Solution. If you want to show appreciation for my efforts today, please take a second to click the Thumbs Up button below.

  If you need assistance, I would be more than happy to continue to help you. Please re-post with the results of the resolution of the problems. Could you please also provide your model number (How can I find my model number or product number?)

  Thank you!

• Problem with the touchpad: Tap to click does not work if I use a standard account

  Hi all

  I have a problem with my laptop that I don't understand and I need help from the community.
  As the title says... If I connect to my laptop using a standard account the touchpad does not work if I try to tap to click. Left and right buttons work, move the slider works, works of scrolling, but endearing tape... not even a single tap. If I log in with my account as an administrator, the touchpad works like a charm, no problems. Tap to click and everything you want. If I disconnect the admin account and sign in as a standard user, the problems are back again. I can move the cursor, click on the two buttons (left, right), but I can't type to click...

  I tried to reinstall the driver for the touchpad (which is MOMENTUM...) but it did not. I tried to see if there is any option that can prevent this tapping or something... but in the control panel > Touchpad > Tap is turned on. A strange thing in the control panel of the Touchpad is that [when loggend as a standard user] I get an error "unhandled exception has occurred in your application. If you click on continue the application will ignore this error and attempt to continue. If you click on exit the application will close immediately. "and a new line saying"index was outside the bounds of the array. If I click on continue the error disappears, but reappears if stationary "double-tap" enable/disable option. If I click on leave the Touchpad Control Panel closes...

  All this trouble occurs only when I use the standard account. With the administrator account, I don't get any errors so I soar options, disable them, activate them and most importantly, the tap to click works.

  What is the problem with the standard account?

  I have Windows 7 Home Premium 64-bit Service Pack 1.

  Can someone help me please?

  Hi Johnxf,

  ·         Did you do changes on the computer before the show?

  As he works in an administrator account, then probably your standard user account have been damaged and would need a fix.

  Follow the article provided below to fix the corrupted user profile:

   

  Difficulty of a corrupted user profile

  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

  Let us know if that helps.