Processor problem

Similar Questions

• Dual Core processor problem

  Hi, I have an Acer Aspire 5720Z computer ultralight laptop with dual core on windows Vista. By a stupid mistake, I stopped him while he was updating software, so now whenever I try to turn it on, the screen goes black and it does not start.

  As it is a dual core, I keep all of my personal information in the D drive (+ photos, docs, etc.), so my question is: if I restore the operating system, are my deleted information even if it is registered in the D drive (not C)?

  I hope you can help me! Thank you

  CR

  Hello

  Dual-core refers to the processor on the motherboard, not to your problem or your disks.

  C: and D: are two partitions on your hard drive Acer; D: as for data on an Acer Acer has a "hidden" recovery partition

  And Yes; If you restore / recover (new) factory settings, you will lose all your data, such as C: and D: are removed and reinstalled like new during the recovery operation.

  Try a system restore to before that the problem using the F8 method (put your Acer in time, NOT again by reinstalling the operating system) in Safe Mode:

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  System Restore:

  http://www.bleepingcomputer.com/tutorials/Windows-Vista-system-restore-Guide/

  See you soon.

• Image processor problem - not tagged profile

  Do you have a problem in Photoshop 6 when using Image Processor to the exit of .jpg.  All the pictures are converted without a color profile (unidentified) Although the profile to convert to sRGB is checked.  Help!

  

  

  Hello

  Don't you have to include the ICC profile checked at the bottom of the dialog box Image Processor?

  

• Codec DivX 6.8.5 (4 logical processors) problem. Need help!

  
  

  Hi Yangtze,

  For the codec problem - I would recommend test avi different filters and see which works best.  To see what filters you have available on your computer, use the GetAVIFilterNames and this will fill a list for you.  From there, you can test to see which gives you the desired playback performance and compression.

  For the problem of Eve - in your VI, call an AVI fence and fence IMAQdx?   It sounds like you might not close all your references, and if you leave them open, even closing LabVIEW is not guaranteed that this.   Tryadding to your program.

  See you soon,.

• High utilization of the processor problem Windows Update

  I still have a recurring problem. CPU runs at about 50%, until I have disable microsoft update, when it goes back to normal, I had this happens twice before, and in both cases it was provisionally fixed by downloading and installing an update from Microsoft. Is there something like this circulating again? Perhaps by coincidence, he started to act up on Patch Tuesday. Is anyone else out there of similar problems? The last two times a LOT of people have had this problem.

  We have identified KB3161664 as the day of this hotfix update must be installed in advance. Download links here:

  http://Wu.krelay.de/en/

  Best regards, VZ

• Color for the image processor problem

  Hello! I tend to work with dozens to hundreds of batch files and often use the Image Processor to save my changes to PSD files to TIFF.
  But I noticed that when I run image processor to save PSD in uncompressed TIFF format, there is a change in the color of the original file in the created file. But... If I manually record a version of the same PSD TIFF (file > save as > etc.), there is no change in color. So... the question is in the processor.

  Y at - it a setting or preference to avoid this to happen? My computer CPU is insufficient? What Miss me?

  "Include icc profile" is checked (at the bottom of the dialog box).

• Motherboard and processor problem

  Dear Sir

  I have forwarded your message to the right people for their review. You should hear from someone bit via private Message on this forum.

• Beep card mother/CPU Dell Inspiron 530 problem

  Hi all!

  I recently acquired an Inspiron 530 G33M02 motherboard with a Dual-Core of E7300 processor.  It worked for a few hours while I was updating windows (my brother had not used for 2 years before), but then all of a sudden the screen empties and computer was turned off.

  To try to restart, the powerbutton lit amber, fans would move for a fraction of a second, and the green light would go on feeding.  I tried the power supply in another computer and it worked while I also installed an another working power known in the Inspiron 530 with the same results.  In research, this lead me to believe the motherboard was bad.

  I have order a new traction (taken before using it on a new computer) on ebay and installed.  Now, I'm getting 7 beeps at the station.  It would point to a faulty processor?  I would limit until I have spend more money on a new processor.

  Thanks for any help/insight!

  smwilli

  7 beeps does not indicate a processor problem,

  http://FTP.Dell.com/manuals/all-products/esuprt_desktop/esuprt_inspiron_desktop/Inspiron-530_owner%27s%20manual_en-us.PDF

  To know if it is the processor, you will need to install in a "known" compatible work computer, or replace it with a compatible CPU "Known", as it is difficult to distinguish a faulty processor of a faulty motherboard.

  While you can make an informed diagnosis, troubleshooting, the complexity of the components, it is sometimes diagnosis by substitution.

  Bev.

   

• HDMI output have suddenly stopped. Pavilion a6340a

  Hello

  I posted here in hope that someone can give me some advice.

  The system in Question is:

  • HP Pavilion a6340a desktop computer. Double heart
  • Vista 32 bit SP2.
  • NVIDIA GF8400GS
  • COMPRO Video mate Vista TV Capture card.
  • 2 GB of RAM.

  It is a bit of an older system, I guess, but it plays well as a HTPC for a while now. It has a small LCD monitor connected via the standard connection and a large flat screen Toshiba TV connected via HDMI. He did a great job.

  Today, the HDMI output just stopped. The Toshiba TV again to survey/is visible in the Nvidia Control Panel and the Vista Control Panel when it is connected to the HDMI. the implementation of the features of multiple monitors are available. But there is nothing happening on TV.

  Things has tried so far.

  • Two different Cables HDMI - nothing.
  • Connected my Pavilion Notebook DV6 on the same HDMI port on the TV - works fine.
  • Installed the latest driver from Nvidia - nothing.
  • Tried all the three HDMI ports on the TV - nothing.
  • Physically, shot the video card in the computer, he dusted off and reassembled it. -Nothing.

  I don't understand. Could this be a processor problem, or I have to pay for a new video card? Is it possible to test the output from the HDMI port with a multimeter or something? I do not understand why it would stop just like that. I just installed Vista SP2 a few weeks ago, but it was working well after I did.

  Any help with this would be greatly appreciated. The system is out of warranty, of course, but it has been a great HTPC for me. I stuck a blu - ray inside player and I was about to give him another 2 GB of RAM.

  Kind of useless now, without HDMI.

  IM at a loss. What else can I do to verify that Exchange of the graphics card?

  Hello

  The short answer is: replace the video card VNvidia GF8400GS. If you happen to have another video card around laying which has an output and HDMI, then install it for a test. It's the fastest way to solve the problem.

  Best regards

  EICO

• Dell Dimension 4600 does not start after upgrading CPU

  Hello

  First of all, I tried to send this last night but received a message on my post approval by moderator? Not yet been approved but seen other people have posted with success more recently. Do not know what is happening.

  In any case, put his hand on a 3.4 Ghz HT P4 Northwood 512 Kb 800 Mhz FSB for £10 on Ebay to upgrade my mother enough old Dimension 4600 which has a 2.8 Ghz P4 512 KB 533 FSB inside... However, when I install it the computer does not light and shows just a light amber. The readers and fans still spin but there is no display. The computer works normally when I put the old one back in.

  I think somehow it is a power supply problem as the new processor uses 20w more energy than the old 2.8 Ghz one. Someone at - it ideas? Just trying to figure if I bought a bad CPU, so I can return.

  Thank you

  Andrew

  AV115

  Hello

  First of all, I tried to send this last night but received a message on my post approval by moderator? Not yet been approved but seen other people have posted with success more recently. Do not know what is happening.

  In any case, put his hand on a 3.4 Ghz HT P4 Northwood 512 Kb 800 Mhz FSB for £10 on Ebay to upgrade my mother enough old Dimension 4600 which has a 2.8 Ghz P4 512 KB 533 FSB inside... However, when I install it the computer does not light and shows just a light amber. The readers and fans still spin but there is no display. The computer works normally when I put the old one back in.

  I think somehow it is a power supply problem as the new processor uses 20w more energy than the old 2.8 Ghz one. Someone at - it ideas? Just trying to figure if I bought a bad CPU, so I can return.

  Thank you

  Andrew

  AV115

  Andrew,

  It is not a power supply problem, it's incompatible, or a bad processor problem.

  The first models of 4600 will take up to 3.0 GHz and models later, 3.2 GHz to 3.4 GHz, but this does not offer much of a sudden boost on the 3.0 GHz

  Motherboard Dell P/N F4491 will support up to 3.4 Ghz Northwood leaving Prescott

  Bev.

• DV7-4060US screen distorted after 1 or 2 minutes

  I have a DV7-4060US who just started acting very strange. After a minute or two, the graphics go all weird. Sometimes, you can still see windows, but there are strange box type blocks that appear in the display. The image and strange boxes are also present when I have an external monitor on as well. So, I tried several things to solve the problem with no luck.

  1. I replaced the hard drive with another that starts with windows and made exactly the same thing. (I simply upgrade the hard drive internal to a DDI and the problem occurs with the player.)

  2 removed the RAM chips (2 x 2 GB chips) and it don't beep solid on the post, then when I put 1 back, (or the other I tested it this way at a time), then the display does the same things again, with a ram chip.

  3 removed the wireless card and tried. (same question)

  4. all removed from the PC and cleaned the fan completely and reassembled. No luck - same question.

  5. deleted the card system (615687-001) and pulled the heat sync it completely and cleaned all the heat sync paste from it. Then, I reapplied new paste and reassembled everything. -Still no luck.

  So here is my question - I'm torn as to time, I have a problem of System Board (615687-001) or (594168-001) processor problem. Part of me is leaning toward the issue of the Board of Directors system because there are more components failed (the luck of the draw on things more as the question on the processor), but there is a nagging me who think that problems with the screen can be related to a processor overheating that has been damaged and now when it is about 1-2 minutes then goes all wobbly. Remember, once he went weird, then it won't start and starts from a pure white. When it does this, then there are times that if let him us stay on the white screen, it will go eventually to a normal screen and be waiting for select us the option "start windows normally".

  Someone out there with other thoughts for me to try?

  Sounds like the system of Council-more precisely the graphics chip. There has been some who arrive to overcome - at least for a while - the failure of gpu to reinvest the gpu chip. There are many tutorials on the internet and youtube to reinvest...

• Phone of blackBerry Smartphones running slow

  OK my phone seems slow... an irritating mini clock appears in the middle of the screen and reverse freezes... What is a processor problem?

  Follow this procedure:

  Options > Security > Advanced security settings > memory cleanup

  Not checked the box enable if it is checked. And try to restart again.

  Good luck!

• Fat heat dissipation issue

  I have a small question.  I have a compaq evo n610c laptop computer a 1.8 GB processor.  I went to upgrade with a processor 2.4 gig, but when I did I used most of the existing dispelling of fat that was on the processor.  The fat was mushy, but I used a good amount and assumed that it would be nice.  I turned on the laptop and 10 minutes later it goes off.  The fan works and carried out, but the case was hot.  He walks again and it stops about 8 minutes later.  Is the old grease the culprit or a processor problem may simply be too hot?  I've never had this problem before and have exchanged several processors in the past.

  Thanks for any help quick before as I tear again

  Kevin

  all you need to do is always use new thermal paste, with cleaning off old batch. Even if it seems good. Once the contact is lost, you need to replace by new ones. Looks like you need to redo your work once again.

• Firefox 8 will work on my old computer (AMD Athlon 64 Processor 3700 +; 2.21 GHz; 896 KMB of Ram). Should I spend (Firefox 3) or will I have problems if I do?

  I have an old computer (the system is: AMD Athlon 64 processor, 3700 +; 2.21 GHz, 896 MB of RAM). I have not upgraded yet of Firefox 3. My system is compatible with the upgrade to Firefox 8? Should I upgrade or will I have problems if I do?

  http://www.Mozilla.org/en-us/Firefox/8.0/system-requirements/

  Your processor supports SSE2 and has more than the minimum RAM recommended, if material wise you are OK. As long as you have SP3 in Windows XP, it looks good for compatibility.

• RAM upgrade problem: Flash the BIOS? or upgrade the processor?

  Hi, I jumped in with both feet and now need help to get out me!

  I have a desktop PC HP Pavilion Elite HPE-470uk who becomes a bit slow (processor card here http://ark.intel.com/products/48505/Intel-Core-i3-550-Processor-4M-Cache-3_20-GHz). After you have added a bluray player that I noticed that it's getting a bit slow so thought I would add little RAM.
  

  I bought a few Hyper X8GB of HyperXbeast 1600hhz, slipped in and the PC did nothing but to turn on and off several times. I checked the two sticks and they both do it. I then (plow in front) checked what memory, the processor can handle and discovered "The Intel® Core™ i3 - 5xx / Intel® Core™ i3-21xx processors handle memory DDR3 1066/1333 MHz" by http://www.intel.com/support/processors/corei3/sb/CS-031175.htm

  After a discussion on another forum, that it has been suggested that I have updated the BIOS because it can allow the processor to manage memory 1600 mhz, but I don't know where to start on this or what version to selected download. I'd appreciate any help you can offer on this.

  The other way, that I can see is to update the processor itself. I thought of nothing too fancy just an i5 because it will allow me to run 3d blurays and should allow me to run some apps at the same time. After reading this http://m.wikihow.com/Upgrade-a-Processor it seems too complicated. Is it really just a matter of taking off the fan, declipsant the old processor, nine droping in and then put on some cooling stick stuff?

  Or should I just return the memory and get good memory?

  See you soon

  Atdot.

  Here are the specifications of original factory for your desktop HP Pavilion Elite HPE-470uk and its card mother MS-7613 (Iona-GL8E). Based on these specifications, this model can support up to 16 GB (4 GB x 4 DIMMs) as follows:

  Dual channel memory architecture
  Four DDR3 DIMM sockets (240 pin)
  PC3-10600 (DDR3-1333)
  PC3-8500 (DDR3-1066)
  Memory non - ECC, unbuffered
  Supports up to 16 GB on 64 bit computers

  In addition, this model can support the following Intel processors;

  Maximum frequency of the processor of the heart < = 2.93GHz
  Intel Core i7 - 8xx (Lynnfield core)
  Intel Core i5 - 7xx (Lynnfield core)
  Intel Core i5 - 6xx (Clarkdale core)
  Intel Core i3 - 5xx (Clarkdale core)

  If you do not have to worry about the update of the BIOS, there is no updates available for your computer BIOS. Honestly, I return the incorrect memory and upgrade to a minimum of 8 GB of RAM. Then, if it solves all your problems, you could also upgrade the processor.

  As the computer is nearly 4 years old, you can consider a factory HP restore to return the computer to a facoty as State. In many cases, it returns original full speed of the computer. The reason why this helps, because the BONE is swollen and clogged over time.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation