Program BACK in Guest XP on Windows 7 does not fill the screen

Similar Questions

• Whenever I try to maximize a window, it does not fill the screen

  I'm running a new Dell laptop on Windows 7 and whenever I try to maximize a window (a web browser, for a folder of files, etc.), display is not going to the top of the screen and there is a 'gap' where I can see my desktop.  Changing the resolution did not help, nor has using the extension/retraction button in the upper right of the browser. Any idea on how I can do this deficiency disappear and displays her fill the entire screen?

  Hello

  I suggest you perform a clean boot and check if that helps, by following the link:

  How to troubleshoot a problem by performing a Clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: Refer to, step 7 'reset the computer to start as usual', after the clean boot is performed.

  I hope this helps.

• Firefox loads, icon on the bar of tasks but when you click the slide of graphics off to the right, but does not fill the screen & when you right-click again, falls back into the icon

  Firefox, Thunderbird and Quicken were active when I loadad & ran a slot machine game. When I left the game & click on icon to return to Firefox full screen, I could see the flash of the image to the right of my screen and disappear. When I clicked on the icon in the taskbar, the reverse happened - the image flashed from the right down to the icon. When I hover the mouse over the icon, the open screens appear with the red X to close, but the same thing happens when I click on this box. Two other programs that have been opened, while the game was active work correctly, only Firefox has been affected. I can't open the program to access one of the menu items that I can't get the image of the screen on the monitor. I did uninstall and reinstall a freshly downloaded copy, I had to use IE, as I am now) but with the same results when I run. I did chose to save my settings, so if something has changed here so maybe that's the problem.

  Hello

  Try Firefox Safe mode to see if the problem goes away. Safe mode is a troubleshooting mode, which disables most of the modules.

  (If you use it, switch to the default theme).

  • You can open Firefox 4.0 + in Safe Mode holding the key SHIFT key when you open the desktop Firefox or shortcut in the start menu.
  • Or open the Help menu and click on the restart with the disabled... modules menu item while Firefox is running.

  Once you get the pop-up, simply select "" boot mode safe. "

  If the issue is not present in Firefox Safe Mode, your problem is probably caused by an extension, and you need to understand that one. To do this, please follow article Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems .

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before you open Firefox for normal use again.

  When find you what is causing your problems, please let us know. It might help others who have the same problem.

  Thank you.

• Window does not fill the screen of the computer

  I have a black margin of 1 inch on each side of the window on my laptop.  How can I get the entire screen to be filled?  I don't know how I messed up this - but I don't know that there is this operator error!

  the cursor won't go the black margn. Thblack margins are around the entire screen with a box in the middle with the window. Help please!

  Next time please start your own thread. This began in July 2009. That is 1 year and 3 months.

  Try this:

  1. set the resolution of the screen
  Right-click on a free space of your desktop computer > click Customize > click on display settings > use the slider to change the resolution > click OK when finished.

  Resolution based on the screen size

  Monitor 15 inch	1024 × 768
  17 to 19 inch monitor	1280 × 1024
  monitor 20 inch and liked	1600 × 1200

  For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• Windows 8 screen does not fill the screen of my laptop, how to correct?

  Just installed windows 8 on my laptop, but it is less broad than the laptop screen (there are black stripes down each side approximately 1 "wide).

  Tried to set the resolution, but it will not let me, how do I fix this please?

  Welcome,

  step 1: download your graphic driver.
  This link might help you:
  http://answers.Microsoft.com/en-us/Windows/Forum/hardware/display-driver-issues-in-Windows-8-consumer/93866a8c-4ef6-4ae5-BD46-58d3e3def5e9
  http://Windows.Microsoft.com/en-pH/Windows/hardware-drivers-help#hardware-drivers-help=Windows-7
  Then, you can change your resolution in the Screen Resolution settings window, or click with the right button of your office.

  
  This site might help you

  http://Windows.Microsoft.com/en-in/Windows-8/get-best-display-monitor

  resolutions of laptop are usually:

  1400 × 1050

  1280 × 800

  1024 × 600 (unusable due to the conflict in the requirements)

• iMac (21.5 inch, mid 2011) programs do not fill the screen

  My windows does not fill the screen, as in there is a small strip at the bottom of my screen which is my desktop wallpaper (screenshot of control to the footer of this website) any application that I use, I still see a bunch of my wallpaper down. I love being able to see my toolbar I have a few apps running for the supervision of different things, which is why I do not enter the mode full screen as it hides everything. Is there a solution to this? I can drag the window down a little and then stretch her so it fills the screen, but a simple refresh my browser or a change in the program, it will break again with the small bar at the bottom again.

  

  Please post a screenshot of the page complete so we can see what you're referring to.

• I use a database program in a number of previous versions of windows and windows 7 does not allow the program to launch denial of service.

  Application of program compatibility does not start

  I use a database program in a number of previous versions of windows and windows 7 does not allow the program to launch denial of service.  What gives?

  If you have Windows 7 64 bit without BACK program can run because there is no 16-bit subsystem to run it.

  Try dosbox http://www.dosbox.com/. If that won't work your program, you'll need either a new database or run the BACK or on a 32-bit version of Windows in a virtual machine like VirtualBox https://www.virtualbox.org/.

• I downloaded Windows 10 and it deleted my Adobe Acrobat and several other programs. I need to download again, but does not have the product key.

  I downloaded Windows 10 and it deleted my Adobe Acrobat and several other programs. I need to download again, but does not have the product key.

  Hi Dean,

  To locate your Acrobat serial n refer to find the serial number of your product Adobe quickly

  Download Acrobat X, see Download Adobe Acrobat products. Standard, Pro | DC, XI, X

  It could be useful!

  Rayyan

• Windows XP does not install the automatic updates.

  Original title: kopieerfout

  After several years, my laptop with Windows XP does not install the automatic updates, giving only a mistake:

  "

  ER is een doing opgetreden bij het van het bestand ntoskrnl.exe copying

  Kan het bestand niet naar doelmap copying.

  Everything works OK.

  Thanks for your help

  Everything works OK.

  It seems that it is not... Why Dutch? You use or have the corresponding language version installed?

  Free translation of message:

  "An error occurred during the copy of the file ntoskrnl.exe
  Cannot copy file to destination... »

  Please note that ntoskrnl.exe is a process in the cycle of the initial startup on your computer program.

  Try to load your "last known good configuration".

  The issue is also known to be caused by a short circuit in the ground cable into the keyboard cable. Make sure that it is not the cause of your error by replacing the keyboard with another keyboard or just disconnect the keyboard from the computer. You can also look at your function "Add or remove programs" If KB2686509 <> http://support.microsoft.com/kb/2686509 > is installed.  Install manually if it is not.

  If the above doesn't help, try using the Sfc.exe tool - see here > http://support.microsoft.com/kb/310747

  Or run the Chkdsk tool - see here > http://support.microsoft.com/kb/315265

  If still no luck, you may need to restore the file ntoskrnl. exe as follows:

  1 - insert the Microsoft Windows XP CD. Note: If you have a recovery CD or a restore CD and not a Microsoft Windows XP CD is probably the procedure below does not solve your problem.

  2 - restart the computer and that the computer starts, you should see a message press any key to boot from the CD. When you see this message press any key.

  3. - in the Microsoft Windows XP setup menu, press the R key to enter the recovery console.

  4 - Select the operating system you want to set and enter the administrator password.

  5 - type expand d:\i386\ntoskrnl.ex_ c:\windows\system32

  6. - you will be asked if you want to overwrite the file, type Y and press enter to replace the file.

  7 - type exit to restart the computer.

  Hope this helps - good luck!

• After you install a second WD 1 TB my book drive, Windows Explorer does not see the new drive.

  Original title: Signature Collision?

  I'm having hard to the installation of a second external drive. I use Windows 7 Ultimate RC. There was a WD 1 TB drive My Book already installed - healthy and works very well. The problem occurred after installing a second WD 1 TB my book reader. I followed all the instructions, pluuging the drive to a USB hub. Windows found the disk, installed drivers and reported the new drive ready for use.

  Windows Explorer does not see the new drive. Devices and printers shows 2 external drives from WD. Disk Management shows as 2 drives, but the second disk is offline because of a 'Signature' Collision

  Each player works very well if it's the only drive plugged in. "Eject My Book" does not work because a program (or more) are to use the player in the background (Windows or Norton).

  I installed the latest firmware and I'm still having this problem. I've been emailing WD with this problem and they are running out of ideas.

  Can anyone help?
  Thank you
  Comatose13

  Hello Comatose13,

  There is an old article of KB in Windows XP that has been recently updated with additional measures to solve this kind of problem. The KB covers Windows XP, Windows Vista and Windows 7 with step by step methods. See if that helps.

  http://support.Microsoft.com/kb/330140

  Bobby

• Windows 8 does not see the hard drive on the Satellite A200

  Windows 8 does not see the hard drive on the A200.
  How to install it?

  S strange Windows 8 should already contain the HARD drive controller driver to recognize the HARD drive during installation.
  The HARD drive is visible in the BIOS?

  Do you use the original disc from Microsoft of Windows 8?

• Satellite L30-105 (PSL33E) Windows Vista does not see the DVD - ram UJ-850 s

  Hello

  I have a Satellite L30-105 (PSL33E) with windows Vista. Windows Vista does not recognize the DVD - ram. BIOS recognize DVD-ram. I tried to download the drivers for the DVD-ram, but they are not on the side of Toshiba.

  Who can help me to get the right driver or learn more? Problems with the carpet * a DVD-ram uj-850 s ATA device and windows Vista.

  Hello

  The CD/DVD drive needs no special drivers!
  Vista includes a Microsoft driver that works with all CURIOUS s (CD/DVD drives)

  Simply said, the Vista should recognize the drive without any problems.

  A few questions; did you get any error messages? What is the status of Device Manager? Do you see yellow exclamation points?

  There is an old way to correct a similar drive problem. It worked on XP then try it on Vista OS.
  It of necessary to update the registry entry
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  1. click on the start menu.
  2. If it is a Vista machine in the search box type regedit without quotes.
  3. look for the registry key mentioned above.
  4. in the right panel you'll see something along the lines of UpperFilter and UpperFilter you want to click on each key filter and tap on delete. Click Yes when asked to confirm if you want to delete the key.
  5. restart Windows.
  6 let me know if it works.

• Windows Messaging does not mask the images in emails after installing ie9

  I have Windows Mail to block images in my emails, but that after the installation Internet Explorer9 windows mail does not block the images in my emails even if the parameters are always the same. I had to uninstall ie9 for this reason, except that ie9 seems to work. Vista Home Premium SP2.

  Stringy salvation,

  Try to upgrade to windows live mail 2011 and check if it works with IE9.
  Maybe just the problem of the software with Windows mail.

  http://explore.live.com/Windows-Live-Mail?OS=other

• LG C500-G. AEE5GE1 with Windows 7 home prem OA MEA have been formatted. But despite giving the product key and Windows registry does not recognize the activation. Help, please

  LG C500-G. AEE5GE1 with Windows 7 home prem OA MEA have been formatted. But despite giving the product key and Windows registry does not recognize the activation. Help, please

  Name of the operating system Microsoft Windows 7 Home Premium

  Version 6.1.7601 Service Pack 1 Build 7601

  Manufacturer of operating system Microsoft Corporation

  System name HANDSOME-PC

  System manufacturer LG Electronics

  System model C500.-g. AEE5GE1

  System Type X 86-based PC

  Processor Intel (r) Core i3 CPU M 390 @ 2.67 GHz, 2666 Mhz, 2 Lossnay, 4 logical processors

  H46YSF00 Version/Date of BIOS American Megatrends Inc., July 2, 10

  Product key:

  X 16-96084

  CONCERNING

  TUESDAY BIOJY

  Have you tried to restart by phone?

  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
  http://support.Microsoft.com/kb/950929/en-us

• Windows 7 does not open the windows in the taskbar. The content seems to be displayed off the screen

  Windows 7 does not open the windows in the taskbar. The content seems to be displayed off the screen. It started after the uninstall of Registry Mechanic and PC Tools, but this cannot be bound. IE 9 seems to be particularly affected. So do not display all of the windows that show on the taskbar.

  Use the Windows logo key & left arrow several times for each windows application through their positions until they appear on the screen.

  This problem is normally reported after someone used an external monitor as the applications try to open in the same position they had when they were last open - so if there was an external monitor last time now disconnected, they will try to open it in the middle of nowhere.

  I know not, or the other tools that you mention, but if they are registry cleaners then they could also affect other parts of your system.