Program does not work after Migration

Similar Questions

• Program does not work after the AIR 23.0.0.246

  I developed a program with Adobe Flash Professional CS6(Air for Desktop)

  the program has worked well for Adobe AIR 22.0.0.153. but after the update to 23.0.0.246, , but this does not work well.  Please help me

  After uninstalling Adobe AIR 23.0.0.257 again, if I install Adobe AIR 22.0.0.153 then this program works well.

  I think that air more recent 23.0.273 solved this problem.

• Scheduler quartz 1.6 does not work after migration application Java of 10g and 11g

  I used the Task Scheduler quartz 1.6 with Java application built in technology from 10g to Oracle using Jdeveloper 10 g as IDE.

  The application works fine with the mentioned technology. But after the migration of the application of technology 11g quartz scheduler does not work anymore. The Weblogic Server allows you to deploy this technology migrated is Weblogic server 10.3

  Finally, the issue is resolved.

  The problem is resolved after you delete the following jar files in my view-controller project: Api .jar-Trinity and the Trinity - impl.jar

• PPR does not work after migrating to ADF 11.1.1.0.2 to 11.1.1.1.1

  Hi, I am able to update my user interface components in ADF 11.1.1.0.2 programmatically. After you migrate my application to ADF 11.1.1.1.0 using the last Jdev, I noticed that all the PPR program no longer work. I use ADF Faces, controlled beans and EJB. Data control is not used.
  
  In addition, I noticed in Section 7: possibilities of content of the partial Page of last User Interface Developer Guide (B31973-03) Web, a new paragraph has been added, indicating that the clientComponent of the target component attribute must be set to "true" to allow PPR programmatically. An earlier version of the developer guide(B31973-01) has not this paragraph.
  
  Is given the huge amount of work going back to update the code, there a way for me to put material ADF 11 GR 1 to restore the previous behavior in 11.1.1.0.2 by setting some somwhere parameter (for example in the web.xml file)?

  No there is no switch. If you don't want to go through your code (which should be possible to find in files with a regular expression), you will need to return to 11.1.1.0.2.
  This would not be an option for me because of the buds set in 11.1.1.1.0.
  Think aoubt the next release which is scheduled for later this year. There you will have the same problem. If you are not fixed the code you have to stay forever on 11.1.1.0.2.

  Timo

• Screen saver program does not work after reinstallation of Win7 (missing Direct 3d devices)

  I had a problem with a screen saver program that has run before on this machine.
  I had to reinstall windows 7 recently and he has not worked since.
  I am running Windows 7 64-bit, the monitor is a Dell 2310 ST s/n is CN-OU217R-72872-O2B-OUJS.
  My PC is a Dell Studio MT Pentium Dual Core E5400 VT (Description of the invoice)

  The error I get is "unable to find any compatible Direct 3d devices.

  The monitor driver is Dell_ST2310_Analog and I checked that there are no new versions.

  There are 3 drivers listed under sound, video and game controllers:

  1 Intel(r) High Definition Audio HDMI
  2. Realtek High Definition Audio
  3. Audio USB device

  I did a scan for #3 and it updated to a Webcam Pro 9000, which is a device that I have attached.
  The other 2 drivers are the latest from the scan.

  It seems that is missing a driver, or I need to change some settings, but I don't know who. Wonder if you could help me.

  Well, you would believe that I received an update from Microsoft Sunday night late and this morning everything works very well.

  Ignore the problem.

• Program does not work after downloading the sp2 and sp3

  After spending hours and hours trying to download sp2 and sp3, I finally got to download completely successfully. for some strange reason when I try to open programs like weather bug and msn messenger they open but close immediately. How can I fix it?

  See...

  Help: I got hacked. Now what should I do?
       http://TechNet.Microsoft.com/en-us/library/cc700813.aspx

  Personal data backup (which none should be considered 100% reliable at this point) then format the HARD disk and do a clean install of Windows.  Please note that a repair installation (upgrade AKA on-site) won't fix this!

  HOW to do a clean install of Windows XP: see method 1 and http://michaelstevenstech.com/cleanxpinstall.html#steps in http://support.microsoft.com/kb/978307

  Once installed the clean, you will have the equivalent of a "new computer" in order to take care of everything on the next page before connecting the machine to the internet or one local network (i.e. other computers) otherwise and before using a flash drive or the SD card that is not brand new, or has not been freshly formatted:

  4 steps to help protect your new computer before going online
       http://www.Microsoft.com/security/pypc.aspx

  Other useful references include:

  HOW to get a computer that is running Windows XP Gold (no Service Pack) fully patched (after a clean install)
  http://groups.Google.com/group/Microsoft.public.windowsupdate/MSG/3f5afa8ed33e121c

  HOW TO get a computer that is running Windows XP SP1 (a) or SP2 fully patched (after a clean install)
  http://groups.Google.com/group/Microsoft.public.WindowsXP.General/MSG/a066ae41add7dd2b

  Tip: After getting the computer fully patched, download/install KB971029 manually: http://support.microsoft.com/kb/971029

  NB: No matter what Norton or McAfee free trial which is preinstalled on the computer when you bought will be reinstalled (but invalid) when Windows is reinstalled. You MUST uninstall the trial for free and download/run the removal tool before installing updates, Windows Service Packs, or updates IE and before installing your new anti-virus application (which will require WinXP SP3 must be installed).

  Norton Removal Tool
       FTP://ftp.Symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  McAfee Consumer product removal tool
       http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

  See also:

  Measures to help prevent spyware
  http://www.Microsoft.com/security/spyware/prevent.aspx

  Measures to help prevent computer worms
  http://www.Microsoft.com/security/worms/prevent.aspx

  Avoid fake security software!
  http://www.Microsoft.com/security/antivirus/rogue.aspx

  If these procedures look too complex - and there is no shame in admitting this isn't your cup of tea - take the machine to a local, good reputation and stand-alone computer (that is, not BigBoxStoreUSA or Geek Squad) repair facility.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• the Windows Setup program does not work after restoring

  Since I restored my system, when I try to open excel or word, I get a windows install. Even after installing windows install 4.5. How can I get excel and word to work?

  Hello

  1. could you give us the exact error message?
  2. do you get this error only when you use Excel?

  Method 1.
  I recommend you to reregister the Installer engine.
  Here's how:
  a. Click Start, click Accessories and then click command prompt.
  b. at the command prompt, type the following and press ENTER after each line:
   
  MSIExec /Unregister
   
  MSIExec/regserver

  
  Method 2.
  

  It seems that there is a background app that launches the installer of Windows. We can perform a boot minimum troubleshooting to find the same thing. You need to perform a clean boot to find the program that is causing and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  I hope this helps.

• Some programs does not work after you run error check.

  My computer was not start properly, so I ran error check, and there are all sorts of bad clusters and fixed them. Now, most of my programs work with the exception of MS Office programs and I Tunes. The message arrives that Windows is looking for a solution, but it never comes to the top with one.

  If you want to say that chkdsk, and who has reported and isolated bad clusters, that means that you drive has failed and you should immediately backup of data before buying a new drive.

  If the drive has which went wrong until it's too late to create an image backup, so you will need to reinstall all origonal media on the new drive.

  I hope you did your recovery discs, when you got the PC.

  The HD machine will have a free disk bootable verification utility, if you want a second opinion

• Jani [programs do not work after migration to Mac]

  I got a new iMac and the store to transfer my data.  My Photoshop and Dreamweaver programs say now I have a Premium trial and will need to purchase to continue to use it.  How can I get these to work on my new iMac?  I bought these January or February 2013.

  Jani

  [As published for the clarity of the question and the future forum search... MOD]

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a way to go to a page to download the Adobe programs if you do not have a disk or drive

  -you will need to enter your original serial number during the installation for non-Cloud programs

  -Cloud desktop http://helpx.adobe.com/creative-cloud/help/creative-cloud-desktop.html

  -Cloud Getting Started https://helpx.adobe.com/creative-cloud.html

  -Membership questions and problems https://forums.adobe.com/thread/1146459

  - or kglad links in response to #1 here can help https://forums.adobe.com/thread/2081216

  Also go to https://forums.adobe.com/community/creative_cloud/creative_cloud_faq

  Lost information - response #1 to https://forums.adobe.com/thread/2008767 if you do not have your serial numbers

• My IllustratorCS4, iMovie and iNdesign CS4 that came with my computer when I bought it about 4 years ago does not work after I was informed by a representative of Adobe until this day my computer. I still have the programs on my computer. How can I get re

  My IllustratorCS4, iMovie and iNdesign CS4 that came with my computer when I bought it about 4 years ago does not work after I was informed by a representative of Adobe until this day my computer. I still have the programs on my computer. How can I get the re install

  If you're ready to uninsntall, then reinstall, you can download at the bottom of the link;

  Download the CS4 products

• Re: Satellite L300 - camera does not work after upgrade to Win7

  As in the subject. Camera does not work after the upgrade to Windows 7. I have tried almost everything found on the Internet. The drivers are installed.

  There is no exclamation point in the system.

  Satellite L300 (PSLB8E)

  Hello

  What happens when you start the webcam app?
  All programs-> Toshiba-> webcam

  Did you install other 3rd software part as for example the Skype that could access the webcam?

  Extra tip: go to BIOS and set it to default, save changes, and then restart the laptop.
  Start Skype for example, check the settings in Skype webcam chose correctly.

  It would be really interesting to know if the other software would be able to use the webcam.

  By the way: have you installed Toshiba face recognition? This software use and access the webcam as well
  Then sometimes it would be possible that this software could block the webcam and webcam tool could not work

• CD/DVD drive does not work after 8 Win instalation

  Since a month since I've updated my windows in windows 8, everything works fine but the DVD - RW.

  When I put the blank cd and try to open it, it gives me error when opening by saying:
  "windows could not complete the format".

  Who's a software or a hardware problem?

  waiting for help!

  This means that your CD/DVD drive no longer works and is not recognized by the system?

  If Yes, then I would recommend checking this Toshiba document that I found on the portal of the knowledge base site:

  + Why my CD/DVD drive does not work after upgrade to Windows 8? +
  http://APS2.toshiba-tro.de/KB0/FAQ2B03F10002R01.htm

  You must uninstall the programs from Toshiba:
  TOSHIBA Recovery Media Creator
  TOSHIBA Disc Creator

• Recovery disc Creator program does not work

  I bought a new Tecra, because I have Nero to burn discs, I removed Sonic my system and after that I recognized that recovery disc Creator program does not work!
  I reinstall Sonic using Toshiba Application install, but nothing has changed and said: my recovery disc Creator program. "shortcut is broken!
  I searched the Forum, but could not find any solution
  is there anywhere to download recovery disk creator program?

  Hello

  the link is still present? If so, right-click on the shortcut and tell what program or the name of the program is linked. Maybe we can find something to take home your recovery disk creator.

  You know, that sounds really weird that a program always disappears after reinstalling the burning program sonic. Maybe it s just a special option or something that needs to be enabled.

  Welcome them

• Tecra M7: Tablet does not work after closing the lid

  Someone had problems with the Tablet does not work after closing the lid on a Tecra M7? BIOS is 3.20

  Does not happen on hibernate or sleep.
  I have the set cover to do nothing on close.

  Hello

  What do you with Tablet does not work after closing the lid?
  Is - what the laptop freezes or what? What happens exactly?

  Closing the parameters adjustable lid to Hibernate or standby mode or no action.
  These settings can be defined in configuration power saver actions.

  If you have some problems with some Toshiba applications installed, I recommend you to reinstall the program and TOSHIBA common Modules that doesn t work properly!

  Best regards

• HP deskjet 3510 does not work after windows 8.1

  My printer HP Deskjet 3510 cannot be detected after windows 8.1.  My computer is a HP Pavilion g6. Now, I would never, I clicked to install, I wish they would send me just windows 7. Laughing out loud

  @klb75,.

  Thanks for posting.

  The cardinal rule of when something does not work after update to 8.1 is put it back in place. This applies to the printing software and all other software. Uninstall from the control panel configuration, programs and features. Then, restart the computer.

  After that, download and install this software: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=al-108718-3&cc=ca&dlc=en&lc=en&os=4158&product=5157483&sw_lang=

  * Thus, before installing the software, disable all Firewall/antivirus software. This software can create conflicts with the printer software.

  If reinstalling it does not help, run print and scan doctor. He could fix it... http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?CC=CA&LC=en&JumpID=ex_r4155/HHO/IPG/ccdoc/printer_diag/&softwareitem=MP-135113-1