programming LabVIEW 2010 how to scxi 1102 and 1503 cascade in scxi 1101 case

Similar Questions

• Title of the window - LabVIEW 2010 - how to delete [filename] in the title bar

  I saw an example in a textbook of a window VI title that doesn't have the [file name] added to the custom text, but can't find a way to do it.

  In file - properties VI - appearance of the window there is a control box for the title of the window delete "same as VI' and allow a custom text, but when I look at the VI window, there still [filename] added.

  Could someone tell me how to remove the file name?

  wildcatherder wrote:

  In file - properties VI - appearance of the window there is a control box for the title of the window delete "same as VI' and allow a custom text, but when I look at the VI window, there still [filename] added.

  The file name is added when the VI does NOT,

  But when the VI runs only your custom text will appear

• How to debug the program Labview that runs in the target of the RT of a Compact RIO

  I use CRIO-9073 for the acquisition of data from sensors. Program Labview is written in RT target and target FPGA. It is posssible to make step wise execution for the program written in the target RT and FPGA target the way purpose us for the debugging of the program in general OS.

  MJM,

  The only way to use the debugging on a VI wrote to FPGA tools is to simulate running on the host computer. You can then deploy the compiled FPGA code on the target and run your VI RT in debug mode if you use the communication of the façade with the host PC.

• How to sit interface with matlab 2010A and labview 2010

  I use tools of simulation interface 5.0 with matlab 2010A and labview 2010, I want to take my cue from matlab, labview but signal transfer, I am facing a problem. I want to know is there any compatibility issue in sit 5.0 or I do something wrong?
  photos of errors are attached.

  natasftw wrote:

  http://digital.NI.com/public.nsf/allkb/02F5FA55FC28BDE1862578A30071F975
  While it is for 2011, I doubt that they decided to remove 64-bit compatibility as they went forward as 64-bit has become more rather than less demand.  In this document,notes LabVIEW Simulation Interface Toolkit does not support 64 bit versions of MATLAB application software."

  The extent of the compatiblitly for 32 - bit, I'd take a peek at: http://digital.ni.com/public.nsf/allkb/D174674A91E5536286257428005C2426

  The OP's question was SIT support 64 - bit version of LabVIEW and 64-bit version of the MATLAB/Simulink itself, not the operating system software.

  Document in your second link is on a completely different topic to have API for LabVIEW and MATLAB/Simulink/RTW (well, mostly Simulink & RTW). Here is the relevant link for the 32-bit compatibility: http://digital.ni.com/public.nsf/allkb/049295038FF0EE2A86257A06006B2DAD is no SIT 64-bit.

  Other underlying issues is that Pharlap does not have a 64-bit version. Finally, simulations are better performed on some RTOS (embedded PXI) for a deterministic execution rather than PC operating systems.

  -BTC

• measures of thermistor using modules SCXI-1102 and SCXI-1303

  Hello

  I have a 1303 SCXI front-end module connected to an SCXI-1102 module

  I read the article detailing how to remove bias and pullup resistors to activate measures of RTD/thermistor on the 1303. What did not mention article was the case plug the excitation source, and what is the best source of operating voltage (normal etc., high precision)

  I was wondering where I can find this information, also, I could do several types of measure on the same 1303? I have an analog voltage to a flow meter, and I would like to put it on the same module as the Thermistors

  Thank you!

  Kevin

  Kevin,

  The pulling up of resistors to connect to + 5 V internally.  If the values are not suitable for your application, you can use those.  It does give you much flexibility but.  The 1303 does not give you any other access to any source of current or voltage through screw terminals.

  Pull upward and pull down resistors are networks of resistors Series 9-pin SIP. So you can edit them in blocks of 8 channels for joint measures.

  Lynn

• I'm doing a Shell call Firefox in the directory C:\Program Files (x 86) of \Mozilla FireFox\ and LabView shell call gives an error.

  I'm doing a Shell call Firefox in the directory C:\Program Files (x 86) of \Mozilla FireFox\ and LabView shell call gives an error. I can go to the BACK shell and make the fine call, but Labview Shell gives several errors. Anyone know how to get around the problem of directory with the name of the Program Files (x 86) directory with space and the (x 86) BACK doesn't seem to like?

  You must use quotation marks.

• How to programmatically clear the Image display control in LabVIEW 2010

  Hello...  I need to do what I say in the title above...  I went here,

  http://digital.NI.com/public.nsf/allkb/514FD61A5F1829EA86256DF6004FDE13

  and bother to follow the directions.  I am, moreover, work in snapshot mode.  So I followed the instructions to clear the display of the Image when you are working in the Snapshot mode, but it didn't work.  Either I'm doing something wrong or maybe (as the instructions seem to imply) that this example was written for LabVIEW 7.1 and 8, but perhaps not for LabVIEW 2010?  Hard to say, but can someone help me understand how to clear display of images (IMAQ/Vision).  I just want to be able to clear an existing image before implementing a new.  How can I do this in LabVIEW 2010?

  Thanks bob...

  Hello Paris1_

  Make this change:

  

  You write the constant Source image in the display of the images, but the Source image is already displayed.

  Select a constant vacuum image to clear the display of the Image.

  

• LabVIEW 2010 - applications and issue of RTE

  Hello

  I am currently using LabVIEW 2009 and my company is upgrading to 2010, and I had a few questions on creating applications and their execution on other computers to open the switch.

  (1) computers that don't have that installed LabVIEW 2010 runtime will be able to run applications developed with LabVIEW 2009 (and earlier versions)?

  1.1) in the contrary case, we will have to rebuild all of our current programs to use the RTE of 2010?

  (2) Conversely, exes, built in 2010 will be able to run on computers that have the installed 2009 RTE?

  (2.1) if not, is there an easy way to downconvert programs written in 2010 so that they run on RTE in 2009?

  (2.2) that we will be able to use the new features in 2010 (as the network streaming, export to excel graphs) if we downconvert for 2009?

  3. If rebuild us some applications that were originally written in 2009 us will it install the RTE of 2010 on the target computers, so that they can run the new version of our application?

  Thank you!

  -Nick

  Applications created in 2009 should the TENS of 2009.  Similarly, applications created in 2010 must RTE of 2010.

  You can install both engines to run on the PC at the same time.  Your .exe will use it is appropriate based on what version it was built in.

• I get the error indicating the niajel.dll missing for HSDIO in labVIEW 2010, can someone help how to solve this problem.

  I'm using LabVIEW 2010 and installed the drivers from device LV2010 and try to use the HSDIO functions, while setting the HSDIO function on the block diagram showing niajel.dll is missing, can someone help me fix this bug.

  I tried to uninstall and install not able to set several times.

  Hello. niajel.dll corresponds to the NOR-TClk, although NEITHER-HSDIO does not specifically use it. You use certain functions TClk?

  Also, what other PXI device driver are installed on the system? Could you give a report on the MAX system?

• Can I get this program converted to readable in Labview 2010?

  Can I get the programs following, converted in readable in Labview 2010? I think the real files are in Labview 2013!

  Thank you

  http://forums.NI.com/T5/version-conversion/BD-p/VersionConversion

• LabVIEW 2010 FPGA: problem with the mean and the variance Subvi

  The Subvi 'Average, Variance and standard deviation' seems to not work properly. The calculation of the average value is ok but std and variance are bad and the results change with representation in an unexpected way. Everyone knows about this problem? Is there a problem with the use of this function?

  Thank you

  Andrea

  Hello Andrea,

  Here is a test for the configuration of your VI (entered I16, 16 samples), saved in LabVIEW 2010 SP1 and the new Subvi. It is relatively simple to adapt it to other configurations, but it does not reconfigure several nodes and constants on the diagram. Let me know if it will work for you.

  Kind regards

  Jim

• The program Excel 2010 keep shutting down and I couldn't get back in.

  Original title: my questions, it's that when someone takes a test for Proveit.com in Excel 2010, Word, Power Point, Access and other computer program?

  My questions, it's that when someone takes a test for Proveit.com in Excel 2010, Word, Power Point, Access and any other computer

  program they really pass?  My problem was when I did the test and then the program Excel 2010 keep shutting down and I couldn't get back in.  Is this normal? Please give me advice so when I take the test again, I know better to have prepared myself for the program.
  Joanne E. Kudlovich
  Winnipeg (Manitoba)
  Canada

  You will need to talk with the people who run Proveit.com.  Only they can tell you if your results were recorded.

• Excel 2010 and labview 2010

  I think that this may have been covered, but if anyone noticed all the differences in the properties of the ActiveX or methods in labview when working with excellent 2007 versus excel 2010? I know at one point Microsoft had changed a few things excellent 97-2003 "and instead select 'value' in your method, you must now choose"value 2". Is the real wait even for excel 2010? I am currently using excel 2007 at work and 2000 at home, and when I opened my code at home, my call nodes 'have the wrong son' still all required entries are correct. Same code on excel 2007; lot of son and the code will be run. I'm just curious to know if anyone has tried to use labview 2010 and excel 2010 together and made a work? I'm opening 1 workbook and wrote to 4 different excel sheets using Windows XP, excel 2007 at work and have windows 7 and want to use excel 2010 home and prefers no problem or to all the least know what are potential problems. Sorry if this confusion. I think it's the best way I can explain that I have MY head wrapped around it yet.  I do not want to write the same code twice for different versions of excel. (write and test at home, then re - write at work)

  http://digital.NI.com/public.nsf/allkb/177D720A428CA72B862567EC00757F0C

  This is an example of what I'm talking about

  Myke,

  While I don't have excel 2010 available to try and see, Microsoft (and MSDN) has a huge amount of information about calls in all versions of Excel.

  Excel 2010 development resources: http://msdn.microsoft.com/en-us/library/ee658205 (office.14) .aspx

  Excel 2007 development resources: http://msdn.microsoft.com/en-us/library/bb979621(v=office.12).aspx

  I hope that helps you start, because I don't have access to excel 2010. Let me know if it works for you.

  Kind regards

  Kyle Mozdzyn

  Engineering applications

  National Instruments

• I have a program that runs in the background of my computer, how can I find and stop him

  How can I find and stop a program that runs in [t] he bottom of everything I do on my computer

  Press CTRL-ALT-DEL

  Launch the Task Manager

  In the Windows Task Manager, click the processes tab.

  Locate the process / click on it (to highlight) / then click on end process

  If my comments have helped please vote as helpful.

  Thank you.

• How can Windows Picture and Fax Viewer - I specify the editing program?

  I set things up so that Windows Picture and Fax Viewer is the default program when I opened a variety of types of image files, which allowed me to get a quick overview without waiting for a program to load full image editing. What I need to be able to do is to specify which program is then launched by WP & FV when I click on the bottom right of the screen edit button - one with text that says "closes this program and opens the image in edit (Ctrl + E).

  If I click with the right mouse button and select 'Open with' and then I can select in the usual list of possible programs, but what I want is to set a default value for each file type so that a left click of the button automatically opens the appropriate program. I tried the "program to choose...". "and"Always use the selected program to open this type of file"route after a right-click on the button, but what is happening is that the selected program then becomes the global default and circumvents WP & FV altogether.

  Any ideas?

  I set things up so that Windows Picture and Fax Viewer is the default program when I opened a variety of types of image files, which allowed me to get a quick overview without waiting for a program to load full image editing. What I need to be able to do is to specify which program is then launched by WP & FV when I click on the bottom right of the screen edit button - one with text that says "closes this program and opens the image in edit (Ctrl + E).

  If I click with the right mouse button and select 'Open with' and then I can select in the usual list of possible programs, but what I want is to set a default value for each file type so that a left click of the button automatically opens the appropriate program. I tried the "program to choose...". "and"Always use the selected program to open this type of file"route after a right-click on the button, but what is happening is that the selected program then becomes the global default and circumvents WP & FV altogether.

  Any ideas?

  ====================================
  See the following article:

  Change the default image editor
  application, called from Windows
  Picture and Fax Viewer
  http://WindowsXP.MVPs.org/imgeditor.htm
  (download the free utility - Imgeditor.zip)

  More information:

  How to open your choice of image editors when
  by clicking on the button Edit in the Windows image
  and Fax Viewer screen.

  Proceed with caution and at your own risk *.

  (FWIW... it's always a good idea to create a system)
  Restore point before editing the registry)

  OK... go to... Start / run and type... "' regedit ' without
  the quotes. Then click on... OK... or press... Come in.

  In the registry... Editor drill down to:

  HKEY_CLASSES_ROOT\SystemFileAssociations\image\shell\edit\command

  In the data column, you should see:

  "% systemroot%\system32\mspaint.exe" "%1".

  (where you see * mspaint * in the example... you'll be)
  See your current default)

  Replace the key with the path to the program that will be
  being your default image editor. I tried to Picture It! 7 sort
  Here's what I changed to.

  "C:\Program Files\Microsoft Picture It! 7\pip.exe"'%1 '.

  Now, my images still open in the picture and Fax Viewer
  But if I left, click on the button Edit... Picture It! 7 opens.

  To replace the string...

  'Default' to select, left click.

  Reach... Edit / change...

  In the "Edit String" field...

  Copy / paste the path to your program choice:

  "C:\Program Files\? \???. "exe" '%1'

  Left click... Ok.

  Now, your images will always open in the picture and Fax
  Viewer, but if you left click on Edit button... your image
  editing program opens...

  Good luck.

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.