Programs endangered after the installation/use when the computer is restarted.

Similar Questions

• When you play Pandora in Chrome, the music pauses when chrome is not the active program or after the computer is idle.

  I want to have music playing in the background while I work in other applications like word or outlook or office remotely or even when I'm not at the computer.

  But if I start audio to play (any source) in my browser Chrome's default, I can work in the other tabs in chrome, but I can't minimize chrome or activate any program or window or it goes to pause my music.
  Also, if I start something to play, I want her to play even after the screen goes to sleep. As soon as the screen goes to sleep, the music stops, then I have to move the mouse to keep going.

  I can't find the settings to correct this, but I think that I have narrowed down it it down to be a W8 problem, is not a browser problem.

  Hey,.

  It is resolved. check if it works for you:
  http://answers.Microsoft.com/en-us/IE/Forum/IE10-windows_8/Pandora-stops-playing-music-when-minimized-in/fc9b01b3-42C5-4977-AFB7-9fc9151e94ba

• How to recover programs lost after the computer has been repaired?

  Original title: ACER laptop help

  I recently had some work on my laptop ACER Aspire 5515 and the guy who worked on it took a bunch of programs out of my computer to help with the repair.  I don't know what all he took off, but I want to recharge my desktop computer with all of the programs that came with it when I bought it.  I do not know a program I want to come back is the one where I can play a DVD.  I can play is no longer a.  The initial problem was that my mouse arrow was frozen on the screen and would not move.  Any help will be greatly appreciated.

  Hello

  Check with the Acer support because they would have provided additional programs that came in the
  the factory computer. You can beed to buy the original installation so support these programs
  are provided in this topic. This disk should be pretty cheap since your already own Windows.

  Acer - USA - Service and Support - drivers
  http://us.Acer.com/AC/en/us/content/support

  Acer - worldwide
  http://www.Acer.com/worldwide/selection.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Download the program again after the computer crash?

  I downloaded 6.0 contribute to my computer at home a few years ago, but the program in a computer crash lost a few days ago.  Program was purchased through a license agreement with my company.  How can I download the program again without charge?

  Download the free trial version Adobe Contribute. Adobe Contribute 6.5

• I get these errors "system of logonUI.exe error, wkscli.dll is missing" after the computer is restarted.

  When I restart my computer, I get a system LogonUI.exe error and wkscli.dll does not appear in my computer! How can I fix this error?

  Original title: System of logonUI.exe error, wkscli.dll is missing

  Chris

  wkscli.dll is the Workstation Client DLL.  It is part of the operating system.  If you have the win 7 dvd you can boot from it and do a repair installation to reinstall the missing DLL

• My compiled program crashes after the first run (LabVIEW 2009)

  I have a compiled program created with LabVIEW 2009 which, in the first round, once the computer is restarted, works fine but after discontinuation of the program, it will not work properly.

  The program uses a compiled Launcher to dynamically activate a set of VI containing the expectation driven by State Machines (QDSM).  Begins subsequent program launcher module appears fine, and his progress bar shows that she starts each of the VI.  Once the Launcher is complete it removes memory launched Dynamics VI and caressed.  The spear that do not reach the main UI that VI is barely long enough for the observer to see (if there is one) then stops.  The program then went from memory I can say.  There is no process in memory or anything.

  Also, when I try to run the installed version of the exe file on a computer with installed 2009 development environment I get this behavior consistently successful launch once again.

  In both case, my program does raise all errors (that are connected), or runtime generates everything I can see.  Also, when I run my program in the development environment the program does that way.  He has no problem at all.

  I have used this style of architecture front of LV8.6 with all the problems.  Can anyone suggest some possible solutions or even a few debugging tips?  I've never had a problem that I could not duplicate in the development environment, so I'm not sure how to start to attack my question.

  Thanks for any help.

  Jason

  

  I solved the problem I think that (at least with regard to the tests on this point revealed).   After that I added the possibility to connect the past States to of the QDSM, I was able to determine that the program was 'plant' after that I dynamically closed the Panel front of the Launcher.  My program is designed to close the Panel before the pitcher, then pop up the façade of the main user interface.   My EXE is inspired to hold the Launcher with my other files QDSM kept outdoors in specific directories.  What seemed to be happening is that when Launcher closed its façade and before UI opening upward the runtime engine decide since it is y no Windows Open he was closing down.  It's my guess on what might happen any way.  I modified my code to change the Launcher window to hidden and delay for 1/2 second to give a chance to fully start running to the main user interface.  This will correct the problem, or at least worked around her.  If someone out there can explain me exactly what is happening that I sure would appreciate it.

  Thanks for all the help that those of you who responded.  Your advice has been very beneficial and certainly led me to a faster resolution.

  Jason

• After the update and restart my computer was like a whole new vista version and the version of office business. All files and emails and contacts and other programs have disappeared!

  I did a system restore to run today.  He had updated 8 minutes before all this happened, but I couldn't say what update caused this.  It's important, so I guess that vista.  All of my Web site and software adobe software for forms and emails, files, photos, everything disappeared as if today, I bought the computer Office exccept was there, but empty. I have even been asked to set up an e-mail account.  I don't know how it happened with an update and cannot lose another day to such a waste of time. I work and am finishing my doctorate so the stability of my work being it is quite serious.  How this happened and how can I keep it doesn't happen. I backup to carbonite.com and have now checked, contacts, emails by the intermediary of today and all the files, but it's scarYYYYY!   I was never warned or the ability to restart or given in error messages.

  Hi Kelly Barr.

  Welcome to Microsoft answers forums!

  Are you referring to (files, emails, contacts and other programs) shortcuts on the desktop?

  When updates are installed on the computer it says system files, this process of service not Microsoft that are running in the background can conflict with updates and tour damage the system settings.

  This problem can also occur if system files are corrupt.

  Try the following in order to recover the desktop icons.

  Even though the desktop icons disappear, the programs are still installed on computer you can launch them.

  Method 1:

  Ø, right click on the desktop

  O select view

  Ø, click show the desktop icons

  Method 2: Click the Start button > select programs > verify if all the programs installed on the computer display > try to start or right click on the program and Select create a shortcut

  Check the updates that triggered this question go by the date.

  1. Click for Start > Control Panel > Classic view > Windows Update.

  2. along the top, click view update history.

  Before you install updates, follow the precautionary steps listed below.

  Step 1: Disable the security software on the taskbar

  Note: Activate security software once theupdates are installed.

  Step 2: Disconnect external devices like printer and scanner, except the mouse, keyboard, and internet connection.

  Step 3: The clean boot computer:- Perform a clean boot (check step 1 in the link)

  http://support.Microsoft.com/kb/929135 ---> how to solve a problem by performing a clean boot in Windows Vista or in Windows 7

  Important: n ' forget not to put the computer to a normal startup after you install updates. Follow step 7 in the link.

  Try to install updates via windows update or you can also download and install the updates manually by accessing the Microsoft Web site.

  Data backup on the computer

  You can use backup and Restore Center integrated in the operating system to back up data.
  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-and-restore-frequently-asked-questions

  Thanks and greetings
  Ajay K
  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows XP Pro on which I run several programs. After the opening of a few applications, I have this message "not enough memory".

  Hello

  I have a PC running Windows XP Pro on which I run several programs. After the opening of a few applications, I have this message "not enough memory".
  When I have this message, I can't open another application, or those in Windows... I have 2 GB of memory and only 700 MB are used.
  If I open the calculator several times (about 65 times), I have the same result.
  Sometimes, I get no error message, but the application does not open.

  Someone knows why?

  Thank you

  Hello

  You did the chnages on computer before this problem?

  I suggest you go through the steps of the following atrticle.

  "Not enough memory" error message appears when you have a large number of programs running.

  http://support.Microsoft.com/kb/126962

  Note: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  322756 (http://support.microsoft.com/kb/322756/ )
  How to back up and restore the registry in Windows.

• Programs can not be started, or no response after the computer was not awake mode "Eve"

  Dear Sir.

  My lap top is under the VISTA system. Now the problem is that all programs can not be started or no response after the computer was not awake mode "Eve". I have to restart the computer to recover the computer to normal state.

  Please please let me have your advice to return to my email address: * email address is removed from the privacy *.

  Thank you very much!

  Eric

  Hi Eric,.

  You can follow these steps:

  Step 1: perform a clean boot to verify if an application or service is causing the problem.

  See this article for more information on the clean boot:
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
   http://support.Microsoft.com/kb/929135

  Steps to perform a clean boot:
  a. click the ORB start on your desktop
  b. type msconfig in the search box and press ENTER.
  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.
  c. in the general tab, click Selective startup.
  d. under Selective startup, clear the check box load startup items.
  e. click on the Services tab, select the hide all Microsoft Services check box and then click Disable all.
  f. click OK.
  g. When prompted, click on restart.

  NOTE: Please check that you start the computer in normal mode after a repair. Follow step 7 article.

  Step 2: Configure the power settings for keyboard, mouse, and other devices.

  a. Click Start, click Control Panel, hardware and sound, and then click keyboard.
  b. click on the Hardware tab, and then click the properties button.
  c. click Change settings.
  d. click the power management tab and verify that the allow this device to wake the computer is selected.
  e. If "Allow this device to wake the computer" was not selected, select it and click OK.
  Follow the same steps for the mouse as well.

  If the problem persists, disconnect all non-essential devices (printers, scanners, USB drives). Restart the computer with only the original mouse, monitor, and
  connected keyboard. If this solves the problem of sleep/wake, one of the devices was causing the problem. Replace a device at a time and test to see if the
  problem occurs again. Continue adding devices and testing until you find the device that causes the problem.

  Refer to this article for additional troubleshooting steps.

  
  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista:
  http://support.Microsoft.com/kb/950686

  Kind regards
  Afzal Taher - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I have already installed creative cloud and illustrator (trial) but when I turn on the computer and restart windows, it fails with error code 16 and need me to remove the program, and reinstall.

  I have already installed creative cloud and illustrator (trial) but when I turn on the computer and restart windows, it fails with error code 16 and need me to remove the program, and reinstall.

  Need help.

  Hello

  Please see the link below.

  Configuration error. CC, CS

  Hope this will help you.

  Kind regards

  Hervé Khare

• HELP PLEASE! The computer was restarted after a bugcheck.

  I was hoping that someone could help me understand what is the cause. This has happened for the past 2 days on one of our servers. The server is a Windows Server 2008 R2 computer.

  That's the message in the event viewer:

  The computer was restarted after a bugcheck.  The bugcheck was: 0 x 00000050 (0 x 0000000000000001, 0xfffff800016d40cc, 0xffffffffffffffd0, 0 x 0000000000000000). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 030313-9156-01.

  This is the message that is displayed on windows re-opening after the accident:

  Signature of the problem:
  Problem event name: BlueScreen
  OS version: 6.1.7601.2.1.0.272.7
  Locale ID: 1033

  More information about the problem:
  BCCode: 50
  BCP1: FFFFFFFFFFFFFFD0
  BCP2: 0000000000000001
  BCP3: FFFFF800016DE0CC
  BCP4: 0000000000000000
  OS version: 6_1_7601
  Service Pack: 1_0
  Product: 272_3

  Files helping to describe the problem:
  C:\Windows\Minidump\030413-8765-01.dmp
  C:\Temp\WER-83783546-0.SysData.XML

  Hello

  Resolve errors stop (blue screen) in Windows 7 - has a section for if you can or cannot start Windows.
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  For BlueScreen troubleshooting methods using BlueScreenView and MyEventViewer see my
  answers if this thread - top 3 RESPONSES (+ 1 other).

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/sometimes-i-get-a-blue-screen-when-using-IE-8/c675b7b8-795f-474d-a1c4-6b77b3fcd990

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  --------------------------------------------------------------------------------------------------

  BCCode: 50 0 x 00000050

  References to Vista also apply to Windows 7.

  Have you recently added any hardware? Have you updated a driver just before
  These began? (Check control panel - updates of Windows to see if all drivers
  have been updated it there all the time, it started) main likely culprits are video
  pilot, other great drivers, memory and antivirus/antispyware/security products
  could be faulty as well as reader questions.

  Use the troubleshooter below and refer to the following message for pilots and
  memory when you get these sections and then return of the disease.
  game needed.

  BCCode: 50 0 x 00000050

  Bug Check 0 x 50: PAGE_FAULT_IN_NONPAGED_AREA

  PAGE_FAULT_IN_NONPAGED_AREA bug control has a value of 0 x 00000050. This indicates that invalid system memory was referenced.

  Important info if you received a STOP Code

  If you received a blue error screen, or a stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you have purchased
  Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer, Contact Support.

  If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.

  These actions could prevent a mistake like this does not happen:

  1. Download and install updates for your computer from Windows Update device drivers.
  2. Scan your computer for computer viruses.
  3. Check your hard drive for errors.

  PAGE_FAULT_IN_NONPAGED_AREA parameters

  The following settings are displayed on the blue screen.

  Parameter	Description
  1	The referenced memory address
  2	0: Read operation 1: Write operation
  3	Address that referenced memory (if known)
  4	Reserved

  If the driver responsible for the error can be identified, its name is printed on the blue screen and stored in memory location (PUNICODE_STRING) KiBugCheckDriver.

  Cause

  Bug control 0 x 50 usually occurs after the installation of a faulty hardware or installation failure of material (usually associated with defective RAM, either main memory, L2 RAM or RAM video cache).

  Another common cause is a defective system service installation.

  Antivirus software can also trigger this error, as can a corrupted NTFS volume.

  Resolution

  
  Fix a defective hardware problem: if the material has been added to the system recently, remove it to see if the error recurs. If the hardware failure existing, remove or replace the faulty component. You must run the diagnostics of material provided by the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  
  Fix a defective system service: disable the service and confirm that this resolves the error. If so, contact the manufacturer of the system service on a possible update. If the error occurs during the system startup, restart your computer, and then press F8 to menu mode characters that displays the choice of operating system. In the Windows Advanced Options menu that results, select the last known good Configuration option. This option is most effective when a pilot or a service is added at a time.

  
  A problem of antivirus software: disable the program and confirm that this resolves the error. If this is the case, contact the manufacturer of the program about a possible update.

  
  Fix a corrupted NTFS volume: run Chkdsk /f /r to detect and repair disk errors. You must reboot the system before the start of the analysis of disk on a system partition. If the SCSI hard disk, check the problems between the SCSI controller and the drive.

  Finally, check the system log in Event Viewer for additional error messages that might help determine the device or driver that generated the error. Disable the cache in memory of the BIOS might also resolve it.

  Remarks

  In general, this address is in the released memory or simply not valid.

  This cannot be protected by a try - except Manager - it can only be protected by a probe.

  BCCode: 50 0 x 00000050<-- read="" this="">
  * 1095.html? order = votes http://www.faultwire.com/solutions-fatal_error/page-fault-in-NONPAGED-Area-0x00000050-

  =========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using the methods above
  It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  Stop Windows 7 to automatically install device drivers
  http://helpdeskgeek.com/Windows-7/stop-Windows-7-from-automatically-installing-device-drivers/

  How to disable automatic driver Installation in Windows 7 / Vista
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/

  Turn off Windows Update Device Driver search prompt in Windows 7 / Vista (for professionals,
  Ultimate and Enterprise)
  http://www.AddictiveTips.com/Windows-tips/disable-Windows-Update-device-driver-search-prompt/

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Fallout 3 stops working after the computer wakes from sleep

  Since the games for Windows Live 3 is out, Fallout 3 has never been the same. He used to work at best my GfWL and now her nightmare. Recently, after that I quit the game and put my computer to sleep, Fallout 3 will stop working completely after wake up. I try to start it and I get them all is a cursor with a small blue rotating light. What is even more strange, is that my computer goes into a State of semi who no longer meet this point where programs and keyboard shortcuts no longer work, but I can browse my hard drive. I try control + SHIFT + ESC to see what the devil but that causes Windows Explorer to stop working. CTRL + Alt + Delete does not work either. No matter what I try, once I start Fallout 3 after the computer wakes from sleep, I can't do the task to the top manager and I can't use my computer. The only way to get it is to hit the reset button or turn off manually. Can someone please help to get rid of this problem?

  Hi murphy449,

  1. did you of recent changes on the computer?

  2. the problem only happens when you start fallout 3 after the sleep mode?

  3. are you able to wake the computer quits successfully sleep mode?

  4. What is the version of Windows installed on the computer?

  Method 1

  I suggest that you manually download and install the latest drivers for display on the computer card and check if it works.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 2

  If the previous step fails then I suggest that you try the clean boot procedure to check whether a third-party program installed on the computer is causing the problem.

  To help resolve the error and other messages, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  If the previous step fails then I suggest you check the observer after return with details and events for the cause.

  What are the information contained in the logs of the event (Event Viewer)?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-information-appears-in-event-logs-Event-Viewer

  What are the information contained in the logs of the event (Event Viewer)?

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• After update, Setup does not take place and causes the computer to restart. This process is ongoing.

  Update Vista was wrong somehow. Update restarted the computer. Very slowly, I get to "configuration of the part 3 of 3, 0% complete do not turn off computer" and shortly after the computer restarts and this process repeats continually. I don't know if the computer has been accidentally closed off the power while the update occurred. Any ideas how to fix. I tried logging in SafeMode w / no luck.

  Windows Update Forum:

  It comes with Vista, upgrade install and activate Forum.

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  You can try a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• The computer was restarted after a bugcheck. The bugcheck was: 0x00000001 (0 x 0000000000000000, 0 0000000000000001, 0x00000000742d2e09, 0xfffff8800aa00b60).

  Computer BSOD'd 2 x today.  The event log States:

  The computer was restarted after a bugcheck. The bugcheck was: 0x00000001 (0 x 0000000000000000, 0 0000000000000001, 0x00000000742d2e09, 0xfffff8800aa00b60).

  LEAPC_INDEX_MISMATCHERREUR (1)
  This is an internal error in the kernel. The most common reason to see this
  error checking is when a file system or a driver has several mismatched
  visits to disable and re-enable the TTB. The data key item is the
  Thread-> CombinedApcDisable field. It's two separate 16-bit
  the SpecialApcDisable and the KernelApcDisable fields. A negative value
  either indicates that a driver has disabled APC normal or special
  (respectively) without reactivation; a positive value indicates that
  a driver allowed normal or special APCS (respectively) too many times.
  Arguments:
  Arg1: 00000000742d2e09, address of function or worker system call
  Arg2: 0000000000000000, thread-> ApcStateIndex
  Arg3: 0000000000000001 (thread-> SpecialApcDisable < 16)="" |="" thread-=""> KernelApcDisable)
  Arg4: fffff8800aa00b60, call type (system call 0-, 1 - routine worker)

  Debugging information:
  ------------------

  TRIAGER: Could not open the file of triage: e:\dump_analysis\program\triage\modclass.ini, error 2

  FAULTING_IP:
  + 0
  00000000' 742d2e09?              ???

  DEFAULT_BUCKET_ID: WIN7_DRIVER_FAULT

  BUGCHECK_STR: 0X1

  Nom_processus: ccSvcHst.exe

  CURRENT_IRQL: 0

  LAST_CONTROL_TRANSFER: from fffff800032841a9 to fffff80003284c00

  STACK_TEXT:
  fffff880 '0aa00928 fffff800' 032841a 9: 00000000'00000001 00000000' 742d2e09 00000000'00000000 00000000'00000001: nt! KeBugCheckEx
  fffff880 '0aa00930 fffff800' 032840e0: 00000000'00001 c 48 00000000' 0780e0a8 00000000' 0780e970 00000980'00000018: nt! KiBugCheckDispatch + 0 x 69
  fffff880 '0aa00a70 00000000' 742d2e09: 00000000'00000000 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiSystemServiceExit + 0 x 245
  00000000' 0780e9b8 00000000'00000000: 00000000'00000000 00000000'00000000 00000000'00000000 00000000'00000000: 0x742d2e09

  STACK_COMMAND: kb

  FOLLOWUP_IP:
  NT! KiSystemServiceExit + 245
  fffff800'032840e0 4883ec50 sub rsp, 50 h

  SYMBOL_STACK_INDEX: 2

  SYMBOL_NAME: nt! KiSystemServiceExit + 245

  FOLLOWUP_NAME: MachineOwner

  MODULE_NAME: nt

  Nom_image: ntkrnlmp.exe

  DEBUG_FLR_IMAGE_TIMESTAMP: 5684191c

  FAILURE_BUCKET_ID: X64_0x1_SysCallNum_4_nt! KiSystemServiceExit + 245

  BUCKET_ID: X64_0x1_SysCallNum_4_nt! KiSystemServiceExit + 245

  These accidents were related to the corruption of memory (probably caused by a driver).

  Run these two tests to check your memory and find which driver is causing the problem.  Launch auditor.  You don't need to run memtest again unless the auditor is not the cause, or you want to.

  If you are overclocking anything reset by default before running these tests.
  In other words STOP! If you don't know what it means that you're probably not  
  
  
  
  
  1-Driver Verifier (for full instructions, see our wiki here)
  
  2-Memtest. (You can learn more about running memtest here)

  Former pilot who need update

  dne64x.sys (Cisco VPN driver since 2008)

  If you continue to plant I remove Symantec and using MSE instead

  Symantec is a common cause of BSOD.

  
  
  I remove and replace it with Microsoft Security if you are using Windows 7 and if you win 8 or higher, use the built-in Defender.
  
  http://us.Norton.com/support/kb/web_view.jsp?wv_type=public_web&docURL=20080710133834EN
  http://www.Microsoft.com/security_essentials/

  Use it to Norton 360 http://Symantec.pcperformancetools.com/Norton-360-how-to-uninstall.html 

• Acrobat 8 Professional can not repair acrobat for El Capitan on mac. If I click Cancel the program repairs her self and work. Once I turned off the computer and restart the same problem persists.

  Acrobat 8 Professional does not work when trying to open .pdf documents. Repair instructions does not work. I use OS X El Captain on my mac. However, if I click on the tab to cancel the program request to make changes to the my computer and when I give permission to the program corrections and to open documents (also the work of program OK after the corrections are installed). However, when the computer is turned off, the corrections are not preserved and I have the same problems whenever I start. How can I get a download to make permanent fixes?

  Post edited by: Alvin Strickland - Acrobat 8 Pro initiates changes automatically once I give permission for changes to the computer and does so in a few seconds, the document opens.

  Hi alvins52918593 ,

  Would like to inform that Acrobat 8 Pro is not compatible with this version of MAC OS.

  Please see this KB article for version requirement older:- Tech specs | Adobe Acrobat Pro XI

  Kind regards

  Christian