Properties: General Description of the channel
Hello
I am trying to identify my different input channels PXI I use and I would use the ' General Propertiesescription ' field to do so. The problem seems to be really simple, but I can't find how to write this field...
How can I change it? It always generates empty when I put a description in the constant channel VI or in the channel to create VI.
Thank you
Oscar
Hi Oscar,.
To write to a property in LabVIEW, you will need to click with the right button on the property node, and then select 'change all to write '. Using this property in write mode, a description for each channel can be set, which can then be extracted using the property even in playback mode.
See the screenshots attached for reference.
Kind regards
Tom - S
MEng (Hons) DRESSED
Technical sales engineer
National Instruments
Tags: NI Hardware
Similar Questions
-
PDM-file: how to set the description of the channel?
Hello
I use the "DAQmx Configure Logging.vi" to capture the raw data from the measurements of May. Which works very well.
At the end, after the acquisition of fiishing, I want to save the PDM. To do this, I want to add some properties to the PDM file. Using "TDMS Set Properties.vi" works, but ot for all properties. I'm able to add the name, description, title, author and date/time (yellow cells in the screenshot). How ca I add the description of the channel (see green cells in the screenshot).
My real simple code to change the properties of PDM:
Thanks for your help.
Better subject.
Michael
If you want to write a property for the channel, you must provide a group and a channel for the service to know which channel the property goes with. If a group is provided but no channels, it assumes that the properties for the group. If neither are provided, it assumes that the file.
Oh, and you should go give this idea a Kudos: Additional metadata TDMS
-
How should I fill out the Description of the channel
Run the example .vi write channel groups (PDM) and then import the .tdms data in Excel with the Excel add in tool
How can I enter information in the Description field of 2nd group?
Thank you
Hi Zilla,
Looking at the 'Description' refers to the Description property of each group. That said, all you need to do is then use the 'TDMS Set Properties.vi"and a cable on behalf of the group you want to set this property to the name of the property (description) and the value you want to store for this property. Is attached the same vi you mentioned in your post, but I changed to store 'Hello' in a description and 'world' in the other.
I hope this helps.
-
Definition of the properties of Description
Hello
I am newto dreamweaver and use version 8. I would firstly the Description parameter properties and looked on the show help page to do this and found the following: see my message below. However, I can't find the Description text box. Any help is to put the description would be much appreciated.
Thank you very much
Martin
Definition of the properties of Description
Search engine robots (programs that automatically browse the web for gathering information for search engines to index) read the contents of the meta Description tag. Some use the information to index your pages in their databases, and some also display the information on the page of search results (instead of display the first lines of your document). Some search engines limit the number of characters they index, so it's a good idea to limit your description to a few words (for example, barbecue pork catering in Albany (Georgia), or web design at reasonable rates for customers around the world).
Enter descriptive text in the Description text box.
A big thank you John, it's exactly what I was looking for.
-
I would enter various notes in the Bookmark Properties window, I had for years. I'd go to Favorites, find the bookmark, click right properties. the s of the Properties window appears, with the name, url, Tag and a Description window. Now when I right click Bookmark, without properties window appears.
I am able to access the Properties window through the bookmarks bar, but not with the bookmark drop down.Hello, you can try to reproduce this behavior when you start firefox in safe mode, once? If not, perhaps an addon intrudes here...
-
in my HPI 6s more, description of the year calendar as "2558 BE."
How can I change to be 2015 or 2016?
Two things to check:
1 settings - general - language and region - calendar - Gregorian
2 settings - general - Date and time - automatically - set rocking on IT
(1095)
-
Writing to the nodes property DAQmx channel does not refresh the channel values
Hi all
I have a riddle. I created a task programmatically in LabVIEW and programmatically added several analog input channels to the task. It's easy.
I wish that my user must be able to modify the individual channels within the task. To this end, I created a set of screws that allow it to change the settings appropriate to the channel (for example, if it is a channel of thermocouple, it can change the type of thermocouple, CRC value, etc... If it is a strain gauge channel, it can change the coefficient of fish and so on). These screws all works beautifully, like the VI where they live.
The specific question that I have is that writing to the channel property nodes refreshes not communication channels. See the images below. The first image is the code that needs to define new channels of communication:
Note that immediately after setting the property nodes, I read their values back, just to see what comes out back.
The second image is an image of the public Service immediately after the execution of this VI. Note that the values read from the channel property nodes did not updated to match to the set of values, but instead kept their initial configuration values:
What I am doing wrong? I fought this for a few days now and I'm stumped.
Thanks for your time!
Diane
Hi, Diane. A week ago, I also had a problem changing the channel properties (not sure that our situtions are exactly comparable, but...). My 'solution' to want to change the appearance of the task was to just throw the original task and recreate all the elements of the task from scratch.
I've not done enough 'experiments' to work when you can and cannot change, but am now much more cautious...
Bob Schor
-
How can I get the name of the channel scale?
Hello.
I am trying to adjust a scale for a channel programmatically in a task. Attached is an excerpt of what I'm trying to do. I am unable to find the name of scale associated with the channel. Ideally when I "ChanType" I'd scale name and move to the scale property node and create the VI of scale.
Thanks a bunch.
(I just noticed the error line not be connected at the beginning.) Has been corrected, but I did not bother to repost.)
Never mind.
Once I simulated the device on my machine, the appropriate properties became available. It's all good.
-
Windows XP 'blocked' file, told to go to properties of "unblock" but the option is not there
I have a file which is compressed. When I try to open it with the wizard the computer says that it has been blocked by Windows XP. When I followed the links on how to unlock, it is said right click on properties and click 'unblock' near the bottom of the dialog box. When I right click on the file, that there is nothing unlock in the dialog box. How to open this file?
Hello
Try these steps and check if it helps to fix the problem:Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the windows below support article.
How to back up and restore the registry in Windows
a. Click Start. Click run.
b. type regedit.exe, and then press ENTER.
c. in the Registry Editor window, navigate to the following location:
HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Attachments\SaveZoneInformation
d. double-click the SaveZoneInformation and set the value to 1. Click OK.
e. restart the computer and check.
For more information, see:
Description of the operation of the Manager of attachments in Microsoft Windows -
"The State of the channel is not valid" _
When I try and open some programs I get an error says "the State of the channel is not valid." Help, please!
Hello zich,.
Look at the following messages which have possible solutions to your "the pipe state is invalid.".
http://www.Vistax64.com/general-discussion/223926-pipe-state-invalid.html
Microsoft MSDN: http://msdn.microsoft.com/en-us/library/ms837754.aspx
Explanation: A pipe operation cannot be performed on a file that does not refer to a pipe.User action: contact the supplier of the current application
I hope this helps.
Sincerely,
Marilyn
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think -
OP: The State of the channel is not valid Code 230
some poured a group of viruses on my VISTA computer. I've tired to restore to an earlier period, but can not get the restore to run. I tried to locate rstrui.exe and right-clicking it goes then properties. Restore to an earlier period does not come to the top. If I click left on rstrui.exe I get the same message, the line is not valid.
I looked in the forum and have not found an answer to this problem. I have the 7 update. install this would fix the problem?
Hello snail,
Do a system restore is not a better way to get rid of viruses on your computer. You should start with the execution of an on-line analysis of Windows Onecare on your computer. Follow the link below to run the scan Windows Onecare online on your computer:
http://OneCare.live.com/site/en-my/default.htm?mkt=en-my
Thank you
Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think. -
Vista will not display description of the file on mouse over. When I mouse over, a pop-up window displays showing: file name, Type, size and Date of change, however, it does not show the description of the file.
So, for example if I have 5 files on different types of screw - the description tells me that the size of the screws. IE. 1.5 mm or 1. 8 mm.
Update: try to get the description of the file displayed messing around in the file properties, now out of 10 records, only 2 includes the name of the file in the mice on the pop-up window. So now what lack us, it's the file name and the Description file.
Help, please...Description of the file in as long as this is not one of the available variables, which can be shown with ToolTips - but there are others who could easily serve the same purpose. Here are the options:
Consulted
Attributes
Created
DocAuthor
DocComments
DocSubject
DocTitle
Modified
Name
Size
Type
To writeHere is an article on how to change what is shown. http://www.ghacks.net/2008/02/10/customize-windows-explorer-tooltips/ . It is to change the registry, make sure you so first back it up before doing anything so that you can recover in case you make a mistake (or do the right thing, but it does not work as expected). http://www.instant-registry-fixes.org/how-to-backup-windows-vista-registry/ .
I hope this helps.
Good luck! Lorien - MCSA/MCSE/network + / A +.
-
Change the channel for Virtual Wifi Miniport Adapter
Hello!
I was experiencing problems of interference when using the module of Virtual wifi miniport, and I would like to know if there is any way I can change the channel on the v-wifi is bradcasting?
THX!
Lee
Well, I tried to find the latest driver for my card, I could find anything to the atheros website (what gives?).
Win 7 told me I got the latest driver, but I wouldn't trust windows update, as they said that my ethernet card was up-to-date (see 7.04) and when I went on the Realtek site, driver to v.7.23...
Anywho! I was not able to change the channel for the ad - hoc connection. I tried the connection with a PC and still cannot connect (so not a problem related to Mac).
I don't know what is happening with the miniport module or the wireless card (I tried different settings in properties and the Advanced Options tab, as power management), but it just would not work. So I got this router, and everything works fine.
This is!
-
Dear all,
While making the cloning of RMAN using the command duplicate in 11.2.0.3 database with ebs.
We receive the error below
connected to the auxiliary database (not started)
RMAN-00571: ===========================================================
RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.
RMAN-00571: ===========================================================
RMAN-03002: failure of Db in dual at 03/07/2015 15:12:07
RMAN-06403: could not get a fully authorized session
RMAN-04006: auxiliary database error: ORA-24327: need explicit attach befor
e a user authentication
RMAN-03015: an error has occurred in the script stored memory Script
RMAN-04014: failed to start: ORA-03113: end of file on communication channel
RMAN-04017: description of the startup error: ORA-32004: outdated or obsolete parameters
ER (s) specified for the instance of RDBMS
Kind regards
Villi Kumar
Dear all,
We have corrected the problems.
Solution:
To the bottom of the database
Comment this parameter and re try
=====================================
oratest@ctsst $ grep-i local initerptest.ora
#local_listener = erptest_LOCAL
oratest@ctsst $
Test the issue again.
Concerning
Villi Kumar
-
Pass the attribute in the Description of the User Interaction
When you add an item to the user interaction to the schema, is there a mechanism to allow me to set the text of description (Overview tab) such that it includes a workflow attribute?
Yep in the interaction user attributes just add the workflow attribute.
Then, under general description presentation add ${local_parameter_name}
Maybe you are looking for
-
I tried to restart, because of multiple restorations system and nothing works.
-
Scanner only works on some computers
I recently bought a Canon LiDE 220 scanner which is supported by El Capitan according to apple of supported scanners page, but whenever I try to scan on my computer it says "Scanner reported an error. Cannot communicate with scanner ". I installed th
-
trying to fix my email... sends
Hello When I send an email it off several times. Please help - me with that. Thank you very much Jeannette
-
How to increase the available on report date range
Hi gurus, On the BigBrother report page, we can define the date range considered. The date start and end on our BigBrother cannot be defined until 2010 (see this screen below). How can I report for 2012 and beyond? Any help will be very appreciated!
-
How can I reset my recycling bin, so that I can restore deleted files
If I accidentally delete files, they are gone forever. I don't have the option to recover more. [Transferred from Internet Explorer]