PropertyNotFoundException: Lack of resources in the implementation of EL:? propertyNotReadable?

Similar Questions

• Problem of lack of resources for IEEE 1394

  We currently have a CVS-1454 with two cameras inspections.  Due to circumstances with the inspection and machine, we try to move the inspections to the computer that communicates with the RESUME.  We get the error "the IEEE 1394 camera could not be initialized because of the lack of resources on the IEEE-1394 bus".  This error occurs only in Vision Builder.  This is not the case in MAX.

  The specific features of the system are: the PC is under XP SP3 with a card PCI-8252.  There are two cameras from Basler scA1390-17fm of the inspection.  The cameras are using the 7 Format, Mode 0, 1392 x 1040.  The PCI card is new out of the box, the cameras are a couple of years.  VBAI version 3.5, LabView 8.6, MAX is version 4.6.2.

  I found the articles on NI.com addressing this issue, but the recommendations have had no effect.

  1. Package size & framerate: in MAX speed can be set on a 100Mbs.  Reduce the size of the package has no effect.  It has been set to the default value to 1024, but we lowered it to 200 without effect.
  2. We installed the driver of Bus AVT Package, but when we went to the driver of the TRA, the bus went to the MAX and then Windows through the new hardware wizard found and we couldn't get the cameras is displayed correctly in the Windows Device Manager, nor did they ever appear in MAX.  All of the documentation I've seen looks that we should not need to install additional drivers for the Basler cameras.
  3. The machine does not have hotfix 885222 installed, but I contemplated trying to run this update anyway: http://support.microsoft.com/kb/955408
  4. Alternate video modes: we have tried to put the cameras to any other video mode.  We can put a camera in an incredibly small resolution, but then the camera still does not work regardless of the video mode.

  I hope that I put all the details there.  Any thoughts?  Should we need to install anything else after the passage in the AVT bus driver?  I was full of hope that would solve the problem.

  Thank you

  Paul

  I agree with Brad, your question is probably the famous issue of Microsoft that XP SP2 and SP3 downgraded a potential to S100 speed, requiring to be restore the driver 1394 SP1 of Microsoft, or switch to Win7 where they finally solved the problem.

  Or by using a substitute 1394 Microsoft compatible spare driver, such as the one offered by AVT.

  But I differ respectfully with Brad that re. If the driver AVT 'worked right' or not... as it was only designed to work with AVT cameras - and will not work with Basler cameras.  This is a deliberate design feature.  Or constraint,'s point of view.  ;-)

  Scott

• Failed to create the edge Gateway. Lack of resources

  Hi all

  I'm introducing an EdgeGateway in my environment of VCD, but every time I try no matter how simple the config of the gateway it will not create it.

  The complaint, what it does is that it cannot find a list of resources for the placement of the bridge on board.

  When I launch the creation I would expect him be tried in the pane Office VC but is yet to happen.

  I read an article that describes manually moving the unit from edge to a different cluster resource after creating, but I don't get as much as that.

  I'm under cloud Suite Advanced and vShield Manager is installed with the loadbalancers for cells. This aspect work fine with vshield.

  I have run out of things to look for now regarding this. There are ample resources available physically if it is not a limitation to this.

  Can anyone suggest what who or where to find more information?

  Debug information will tell you nothing or other various lines of Java code.

  Thank you

  Norton

  Solution has been found.

  I found the problem in the log for debugging on the servers of the cell. You can see try storage and do not.

  For those of you who also see this question, then please check the following recommended by vmware supports known issues.

  Make sure that your storage space has been configured correctly and that you have profiles of storage associated with it.

  You will also need to show your thresholds for storage as it is also a question to know the cause.

  For me, I had to create a new storage cluster and move this cluster of each data store.

  Then refresh the profiles of storage within the VC of VCD element and also to update the connection of VC in VCD.

  Then restart the Service of VC on the VC Server

  Restart the vShield Manager and then wait 5 minutes for the vShield Manager to resynchronize itself and return to normal.

  Now, try again and I hope you should be successful.

• Guard application launch at the start of the appliance, also need advice for the implementation of network methods

  Hi all

  I'm new to the development of Blackberry and I'm writing a relatively simple application to run on 7.1.

  So far the development was interesting, I managed to create my user interface using resources online (mainly this forum), but today I tried to implement some of the network classes that I need and now I just met constant problems.

  I use Eclipse SDK 3.7.2 (the one that comes with the plugin RIM)

  First question:

  I'm not sure what I changed, but today I noticed that whenever I start the Simulator (by sim 9360) my application is started during the initial startup process. I don't think he did this before, but to be honest, I wasn't paying much attention. I think it starts at the start of the device is because I put a breakpoint in the constructor for my class from the main screen, which is hit before the Simulator happens even to the point where it is ready for user interaction. In addition, once it is ready, if I press the BB button, I see my registered application.

  I don't have it set to automatic start in .xml descriptior enforcement.

  I started this application on the HelloBlackBerry sample, here is my main method for the entry of the application:

  public static void main( String[] args ) {
          appSettings = AppSettings.fetch();
          // Create a new instance of the application and make the currently
          // running thread the application's event dispatch thread.
          HelloBlackBerry theApp = new HelloBlackBerry();
          theApp.enterEventDispatcher();
          //openConnection();
  
      }
  
  
  

  As far as I know, this is the only entry point for the application.

  More code

      public HelloBlackBerry() {
          // Push a screen onto the UI stack for rendering.
          mainScreen = new ScreenHelloBlackBerry();
          pushScreen( mainScreen );
      }
  

  Here is the method of. my class AppSettings fetch()

      // Retrieves a copy of the effective properties set from storage.
      public static AppSettings fetch()
      {
          AppSettings savedSettings = (AppSettings) _store.getContents();
          return new AppSettings(savedSettings);
      }
  

  Some of this code that I wrote myself, the persistence store cause the launch of my car?

  I tried to reset the Simulator to the factory settings, no change.

  All applications initialized during the startup of the device and then closed shortly after?

  Part 2: Need advice for the implementation of functions of network in the application

  I need to implement some methods that will retrieve data from a web service, and I also need to send data to this service. What I've read, the ConnectionFactory is the way to go. I want my application to make a request when the application is open and can check on a set interval. I didn't know exactly how to go about adding another thread for networking, I understand that network connections should not be created on the thread main event, so I tried to do this:

  The constructor of my class that implements screen (ScreenHelloBlackBerry), I use the following to create a modal dialog box to prompt the user for a username, I also try networking wire in the same segment of spawning:

          public ScreenHelloBlackBerry(){...initialize fields and managers, add it all together...then near the end
  
  //This will open the confirm dialog when the application is launched
          UiApplication.getUiApplication().invokeLater(new Runnable() {
                public void run() {
                    openConfirmDialog();
                  //start connection - Possibly broken
                    ConnectionThread ct = new ConnectionThread();
                    ct.start();
                }
          });
  

  I don't know if it's somehow OK to do, but it seems to work for what I need. I want a user who launches the application at the prompt, and if a user switch applications, when they come back they wondered again (unless they close the app and reopen it).

  Here is my ConnectionThread:

  public class ConnectionThread extends Thread
  {
  
      public void run()
      {
  
            ConnectionFactory connFact = new ConnectionFactory();
            ConnectionDescriptor connDesc;
            connDesc = connFact.getConnection("http://www.google.com");
            if (connDesc != null)
            {
                HttpConnection httpConn;
                httpConn = (HttpConnection)connDesc.getConnection();
                try
                {
                    final int iResponseCode = httpConn.getResponseCode();
                    UiApplication.getUiApplication().invokeLater(new Runnable()
                    {
                        public void run()
                        {
                            Dialog.alert("Response code: " +
                                          Integer.toString(iResponseCode));
  
                        }
                     });
                    httpConn.close();
  
                 }
                 catch (IOException e)
                 {
                   System.err.println("Caught IOException: "
                        + e.getMessage());
                 }
            }
      }
  }
  

  At the moment it has basically unmodified code from a sample that I found, I'll be retooling to meet my needs whenever I can make it work. I HAD this work to the point where, after the closed user confirm this dialog, a few moments later a an alert dialog appears with the 302 response code. I don't know what changed, but now it doesn't work at all, and if I try to scroll with the debugger, I can't past the httpCon.getResponseCode (). I've seen some mistakes earlier on "no record of service was set up", and I also had once a timeout exception.

  I'm sure I'm doing this wrong, but at the same time as I said WAS working, and now it is not. If someone has done this far, thank you very much for your time and advice are much appreciated.

  Also, should I try to start the thread of the network of the UIApplication class instead of the screen? There is currently very little happening in the class that extends UIApplication, do I spend most of my business logic out of the class of the screen and in the UIApplication class?

  Thanks in advance!

  Hi all

  Just to conclude this topic for those who are interested, I found an excellent guide to the implementation of networks in applications of BB, click here for a link.

  About my application being started at the start of the simulator of the device, I found that on a device real this behavior is not complied with, and in addition, the behaviour seems to have stopped after uninstallation and reinstallation of my Simulator.

  See you soon,.

• Doubt the implementation in a VPN between a VPN3005 and a Cisco 827 router

  Imagine this:

  Establish a VPN tunnel between the central administration (VPN3005) and a branch (827). Only need to spend intellectual property data in the tunnel and the two sites must reach the resources of the other, which means I don't want not just any what NAT involved.

  Can someone tell me what is the way to better/simple to do this?

  Can it be implemented with Cisco easy VPN? (or not, due to not wanting to make any type of NAT)

  Thanks in advance!

  Hello

  I would have preferred a VPN Tunnel from Lan to Lan. I have attached a few URLS that

  explains the implementation of IPSec Lan to Lan tunnel in different scenarios:

  1. with the router with a static routable ip address

  http://www.Cisco.com/warp/public/471/ALTIGAR.shtml

  2. with the router is assigned an IP via DHCP.

  http://www.Cisco.com/warp/public/471/vpn3k_iosdhcp.html

  Kind regards

  Arul

• Untrapped exception blackBerry Smartphones: lack of resources net.rim.device.apps.internal.bis.resource.BISClient

  Hello

  I got a new Blackberry, the 9360, not more than 24 hours and I got this error "exception Eception: lack of resources net.rim.device.apps.internal.bis.resource.BISClient"

  I don't know how to cope, but I get this every time I have to restart the device.

  Can someone help me?

  Thank you

  All your support remains I said earlier... your carrier or dealer is responsible for all your formal support and services. Enter your questions for them, and they would have the possibility of that degenerate into RIM if necessary. Carriers are 100% responsible for packages of OS they choose to get out... RIM releases OS packages only for carriers and companies decide if they wish to release to their users, and if they do while they are responsible for support for it.

  Good luck!

• OIM 11 g: how to manage the resources of the disabled users?

  In the OIM 11g Admin Console UI, when you work with the resources of a user "Disabled", none of the buttons on toolbar for management of resources (Revoke, Enable, Disable) are active.
  
  We have a lot of use cases where users with disabilities resources need to be managed, but it doesn't look like this is possible through the OIM 11 g APIs. (it has been possible in IOM 9 x).
  
  The only solution that we currently have is to enter into the history of resources manually add the appropriate tasks, which is not a very effective solution.
  
  Is this behavior "as planned" or is there a setting somewhere I'm setting that controls this lack.

  You are right, you cannot manipulate the State of the resources of the user if the user is disabled. You can use the API however I think you meant cannot use the user interface.

  -Kevin

• Insert object XObject in the dict of resources at the level of the page

  Hello

  I'm trying to insert an XObject object into a dict of resources at the level of the page (to decrease the size of the pdf). So I created a dict of resources in the 'Pages' object described below:

  Catalog

  Pages

  Resources

  XObject

  XObject_Unique_Name

  Children

  ....

  I call the XObject of pages that are stored as Kids, but it does not work. (called with ' / XObject_Unique_Name Do ")

  What I have to do something more or does it work?

  Thanks in advance,

  Joe

  Shared resources is a deprecated feature of PDF and actually rejected in a number of standards subset due to the complexity of the implementation.   Then "say no."

  Since you have only a single copy real data in the PDF file (which is the use of large file size), referring to it in the dictionary of resources on each page is not a huge success. And if you want to reduce this size, don't forget to use Compression of PDF 1.5 object (aka the total Compression).

• How to complete the implementation of process after inserting the new sim card to unlock the phone

  Try to unlock the phone more 6s with ATT, but do not know how to perform the implementation of process after inserting the new sim card. I got the unlock code confirmed att.

  After the unlock code is confirmed, you will have to restore the unit to the factory via iTunes settings.  He must inform you that the device is unlocked, THEN you change sim cards.

• How to add steps before job Auto resources to the request referred to in the annex to the Auto

  I hope that I can describe my question clearly for you.

  My sequence is something like the following:

  

  It is a simple sequence.

  Test # 2 is faster that 1 Test so that it usually leads to test 1 is occupied by a testsocket and expected by the other testsocket.

  However, the process of loan (10 seconds) is independent of the resource, and it's too long.

  My question is... can I do the lending market (10 seconds) when the Test 1 is occupied by other testsocket?

  The step of resources at the request of uto use A contains an array of resource Expressions.  The idea behind this is that you have 2 instruments on your BENCH that are the same.  In this way, the test may choose to use one or the other and still accomplish his goal.  So what happens is that if you don't have only one resource, then any thread gets there first takes the resource and locks.  Other threads cannot enter this article until at least one resource is available.  So if you dynamically add resources then you can allow other threads in this article.

  You can consider making a step in the Routine 2 which adds a resource to the Routine 1.  In this way, they won't all get routine 1 front 2 routine.

  I think that to get the desired behavior, you're going to need to do some manipulation of dynamic resource expression.

  Kind regards

• Moto G3 - lack of concentration on the edge of the image

  Hi all

  I recently bought Moto G3 after owning Moto E2. I decided to do it because of better camera and a flash.

  Unfortunately, I discovered that the photos on my G3 suffer the lack of development on the right edge of the photo (or left, or low or high, depending on how I am now). I have to say my best update automatic E2 manipulated. I would like to know if it of just my phone or is - this common among all the G3s. I have attached the photos for comparison.

  Here is a link for more pictures:

  https://drive.Google.com/folderview?ID=0B9ufszI2lUPgZEoxNnF0M01YZFE&USP=sharing

  I see that the photos are normal.

• How can I get my new/old office to connect to the internet? I ran to the implementation of new Internet and network connection wizards, nothing happens.

  LAN and WLAN connections

  My old wired desktop xp died, it was the first computer on my home network. My friend just got a new office and gave me an old. I have a laptop which has windows 7 and is connected wireless. It is still plugged in and works fine.  How can I get my new/old office to connect to the internet? I ran to the implementation of new Internet and network connection wizards, nothing happens. When I go to internet connections, it shows that it is connected, but I can't seem to connect. Help, please!

  Hi ShannonStrong,

  ·         What exactly happens when you try to connect to the network?

  ·         You receive an error message or error code?

  You can follow the steps in the Microsoft Knowledge Base article mentioned below and check.

  How to troubleshoot possible causes of Internet connection problems in Windows XP

  http://support.Microsoft.com/kb/314095

  You can also see this article:

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

   

  Note: The article also applies to Windows XP

  Let us know if this information useful.

• ATTENTION: lack of events in the event log

  I am slot as Vista Home Premium 64-bit. I have never received this warning before in a reliability and a report on the return, but three times today I received a warning that lack of events in the log. The percentage varies with each data collection. As you know that surely, he asserts that a possibility is ETW buffers and buffer size may be too small but it has never had this problem before. I ran a chkdsk and has not helped. I checked services and turned everything on automatic to make sure that all services are in the State of the device of the necessary Log data collection.

  What I do or is - nothing.

  Hello

  You can follow the links below and check if they are a help.

  http://msdn.Microsoft.com/en-us/library/ff190866.aspx

  http://social.msdn.Microsoft.com/forums/en/ETW/thread/a1aa1350-41A0-4490-9ae3-9b4520aeb9d4

  If this does not help, you can post your request in the MSDN forums for assistance.

  http://social.msdn.Microsoft.com/forums/en/ETW/threads

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• \\mycomputername is not accessible. you might not have permission to use this network resource. comtact the administrator of this server to find out if you have access permissions.

  \\mycomputername is not accessible. you might not have permission to use this network resource. comtact the administrator of this server to find out if you have access permissions.

  Hello

  Thank you for giving us the opportunity to help you with the query.

  I understand the inconvenience caused, now that you have me with you I would take care of that.

  I suggest you refer to the steps suggested byJack MVP (replied on August 29, 2010)

  In the next thread that speaks of a possible solution to the related question.

  PC is not accessible. You might not have permission to use this network resource. Contact the editable from this server to find out if you have access permissions.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/PC-is-not-accessible-you-might-not-have-permission/26a1a479-8BA5-4213-9181-02364c884937

  It will be useful.

  Let us know the status, we are happy to help you further.

• The implementation of ListFieldCallback

  Hello

  I am new to the Blackberry development environment and I am developing an application that contains a screen with elements of the text list (list item). I have a lot of reading development guides, I am naïve in the implementation of ListCallback.

  Can anyone help me regarding the same (as private class ListCallback implements ListFieldCallback)

  Thank you & best regards

  Siva

  Hi and welcome to the forums.

  You will find a new developer of BlackBerry, many of your questions is probably have been asked before.  So, do a search in the forum.  It is not so easy to search, so try a number of different keywords if you can.

  In this case, if you had sought a "sample listfield", you probably would have found this thread as the first link.

  http://supportforums.BlackBerry.com/T5/Java-development/simple-ListField-example/TD-p/426809

  There are other establishments, but I think it will help you.

  Hope he does and we hope your enjoy BlackBerry development experience.