Proxy DHCP does not
I have two WLC 4402 interview several SSID. Each SSID is a VLAN different with a different IP subnet.
Now, I want to use a single server DHCP for the SSID. So I set up the server (I code applications for different networking option 82), put him in the VIRTUAL LAN where the PA-manager and resident on and configured management interfaces address of the interfaces on the WLC DHCP server suitable for the new configuration.
Now my problem: no request arrives at the server level. Now, I tried almost all the options, but without success.
I discovered that the relay works if the DHCP server is on the SAME subnet. Then all queries are relayed (Yes, relayed, monodiffusees by the controller).
Debugging DHCP from the WLC says:
Op DHCP received BOOTREQUEST (1) (len 313, port 1, encap 0xec03)
1 - relay DHCP selection control block parameters: dhcpServer: 10.22.72.3, dhcpNetmask: 255.255.248.0, dhcpGateway: 10.22.72.33, dhcpRelay: 10.22.72.1 VLAN: 22
DHCP selected relay 1 - 10.22.72.3 (address local 10.22.72.1, gateway 10.22.72.3, VLAN 22, port 1)
DHCP forwarding DHCP REQUEST (3)
...
So now I enter the address of the DHCP server on the new server (accessible directly but the ap amanager and management of interfaces) I get the following:
Op DHCP received BOOTREQUEST (1) (len 308, port 1, encap 0xec03)
1 - relay DHCP selection control block parameters: dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0, dhcpGateway: 0.0.0.0, dhcpRelay: 10.6.72.1 VLAN: 640
1 DHCP relay selected NONE
It just seems to ignore the address of the registered DHCP server.
I tried several versions of the software (v4.2, v5.2), anyway.
Proxy DHCP is turned on - as mentioned, if the DHCP server is on the same subnet, it works fine.
Any suggestions?
OK, so the DHCP server doesn't have an entry door, so may not respond to a request on another network. That's the problem. With this config you would never get DHCP works, that you saw.
Not the WLC will not send the DHCP request for x vlan on y vlan... DHCP must be accessible...
Tags: Cisco Wireless
Similar Questions
-
The proxy server does not-Windows Internet Explorer
After completing the windows updates, I started getting the following message every time I tried to enter in IE10: the proxy server does not-Windows Internet Explorer.
1. try changing the proxy server settings in Internet Options > connections > LAN settings. All the options are greyed out, cannot be changed.
2. I checked that I am an administrator on the computer user.
3. get the same error message, both wired and wireless configurations in.
4. do you have a restore point at an earlier date - the same error.
5A attempted to use Firefox 15.0.1 and I get the error message: the proxy server refuses connections
My system:
Acer
AOD255
Intel (r) CPU Atom N550 1.50 GHz 1.50 GHz
1.00 GB OF RAM
32-bit operating system
Windows 7 Starter
Service Pack 1
Hello.. Please try following method to solve your problem.
Tools-> Internet options and click the Advanced tab, and then tap on restore avancΘs to restore the default settings of Microsoft internet explore.
If you still have problem
go to tools-> internet Options-> Advanced-> Reset internet explore settings click on the Reset button.
-
DHCP does not not in windows8 pro
I use the Windows8 Pro and DHCP does not work properly when I connect to wireless networks. How can I fix?
Hello
Reset TCP/IP.
The reset command is available in the context of the NetShell utility IP. Follow these steps to use the reset command to reset TCP/IP manually:
1. open administrative mode command prompt.
2. when the pop up user account control box, click Yes.
3. at the command prompt, copy and paste (or type) that follows the command, and then press ENTER:
netsh int ip reset c:\resetlog.txt
Note If you do not want to specify a path of the directory for the log file, use the following command:
netsh int ip reset resetlog.txt4 restart the computer.
1 connect to your router (by typing 192.168.0.1 or 192.168.1.1 in the address bar) and connect. Check your user manual or documentation if you don't know the references of logon.
2. make sure that you are in Setup-> basic configuration category.
3. scroll down until you see "DHCP Server" - if it is disabled, select 'enable '.
4 enable DHCP if you want, you can change the number that starts the DHCP IP setting. (This is optional)
5. use the DNS servers provided by your ISP. There are many DNS servers out there. It is preferable to use your ISP if possible.
6. scroll and click 'Save Settings'.
Step 2.
1. click on start and then Control Panel.
2. go to network and sharing Center and then click on change adapter settings.
3. right click on the connection to the Local network and select Properties.
4. Select Internet Protocol Version 6, and then click Properties.
5. select Obtain DNS server automatically an address and press Ok.
6. choose obtain an IP address automatically.
7. repeat the steps for Internet Protocol version 4 as well.http://Windows.Microsoft.com/en-in/Windows-8/cant-connect-to-a-network
-
25.0A1 Nightly of Firefox (on Linux) - proxy (SOCKS) does not work
Hello
I am using SSH tunnels to create a SOCKS proxy. When I used Firefox 23 it works fine, when I use a recent version of every night, don't worry. I use an add-on of FoxyProxy normally, but I tried to turn it off completely and use the proxy settings internal (SOCKS, localhost, 6789) then it does not work either.
I understand, you may need more detailed information, but please specify what information you require.
Thanks for your help
I'm really sorry, I have some additional info
I tried to run every night in safe mode and manually set the SOCKS proxy and it works as assumed.
In this case, it might be a problem with the addon code
-
I have some aging confuguring my proxy server.IE does not ask me for the username and password for the server after entering the name and port.Therefore, whenever I try to navigate, I'm connected to the server, but it blocks me saying: "authentication failed" because the username and password did not intervene.Why is this not to come and especially how it can be repaired. I tried IE, Firefox and Chrome, with uninstalled Antivirus and always without success.Help much appreciated.
Thank you.
Managed to finally make it work.
Go to Internet options > Security > Internet > Custom > authenticating user > automatic login with user name and password has been around.
Password box came. :)
Works fine now in Internet Explorer. Impossible to get all other browsers to work but it's not serious.
Appreciate the help.
-
Cisco WLC 2504 internal DHCP does not work properly
Hi all
I m trials with a Cisco WLC 2504 and some APs of 1832. I set up a DHCP scope on the interface of the controller with 2
a large number of different configurations, but the DHCP protocol does not work and Don t Access Point to obtain an IP address. My first question: is it possible to do DHCP for Access Points or only for wireless clients?
These are my interfaces:
Interface of the PA-Manager:
My DHCP scope:
Advanced DHCP:
I forgot something? Is there anyone using DHCP for its access points?
Thank you!
Hello
On Cisco WLC internal DHCP, you can add the option 43 to say where APs must register. In this case, they will try to resolve the DNS CISCO-CAPWAP-CONTROLLER or CISCO-LWAPP entry.
Let me explain briefly how AP-Manager works on WLC:
- Boots of Access Point and sends a discovery request to the management interface of the controller using the intellectual property you configured as DHCP Option 43 (as described above, it can be resolved by the DNS entry)
- Controller, sends it a response discovered that contains the name of the system, addresses AP-Manager, the number of access points already connected to each interface AP-Manager and the overall capacity of the controller.
- Joints access point controller using the less loaded interface AP Manager.
With this, every AP Manager must have a good configured interface and be connected to a different port, no LAG.
I drop a post here sometimes there is which might help:
https://supportforums.Cisco.com/document/118311/configuring-multiple-AP-...
Thank you
PS: Please do not forget to rate and score as correct answer if this answered your question
-
With the help of my signature via a proxy server does not terminate but not from RIM
I now use the signature Server successfully to sign sensitive data on the device
associated with our application.
However, when trying to sign full RIM signatures through a proxy server, and my
Server deals in reality as well and even send emails of success, but the signing tool
does not receive a final acknowledgement that he search and eventually times out.
I noticed for RIM signatures that we are hitting servlets, while the default configuration value for our
signature server is used.
Is there something we need to do for our server works correctly when it is connected through the proxy?
NOTE: everything works fine when the server is on the same network as the GIS tool.
Thank you
Mark
It turns out that it's the server signature RIM as I expected. It does not return the appropriate response headers.
The server does only return HTTP/1.1 200 OKCRLF and then the payload. We discovered
If we put an Apache proxy before the server signature and after our proxy
that it will accommodate the non-standard answer and mark the headers with a stored block transfer
coding and then all is good.
So the reason why the public signature RIM servers work through the proxy must be either because the bug
This server is fixed or a proxy because Apache-like sitting in front of the signature server.
I hope that this will save others some grief in the future.
concerning
-
Client DHCP does not not on my desk
I can't connect to internet on my desktop computer, ethernet light shows like work, but send it and receive lights blinking. The DHCP client is not running on this computer appears - and also a problem with your modem broadband may prevent any connection to the internet. However, I can connect properly using my laptop - as I am now. How can I fix the connection on my desktop?
Hello
What is the exact error message and the error code?
Try the following and see if it helps.
Method 1:
Network connection problems: http://windows.microsoft.com/en-us/windows-vista/Troubleshoot-network-connection-problems
Method 2:
Check the proxy server settings are turned on. To do this, try the following steps:
a. disable the proxy on Internet Explorer (IE)
b. Click Start, type inetcpl.cpl and press to enter.
c. click on the Connections tab, click the LAN Settings button.
d. uncheck "Use a proxy server for your LAN" under proxy server.
e. click ok to apply the changes.
f. open Internet Explorer and check if the problem persists.Method 3:
Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers: http://support.microsoft.com/kb/928233
Note: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry
Also see: http://windows.microsoft.com/en-us/windows-vista/change-tcp-ip-settings
Note: If you are always faced with the question, I suggest you try to contact an ISP (ISP) to verify connectivity and for further assistance settings.
I hope this helps.
-
Update to 6.5 vm: bridged dhcp does not work anymore
I have an older version of VM machine 5 with windows xp sp3 on it.
With the help of vm workstation 6.5 I improved the VM to 6.5.
From that moment, the virtual network adapter is not able to get an ip address from the router on the host computer
where it is connected via the network bridge.
If I set a fixed IP address (in the subnet host range) everything works fine.
so, my conclusion was that somehow dhcp queries fail.
Decommissioning of the VM to version 5 again fixed things. DHCP works again.
Someone at - it an idea how I could solve this problem?
No, we have to GUESS why he had with a front fixed IP... I swear to you, so many "problems" would be resolved itself if people actually have the time to learn what they are doing. OR the age old RTFM before you do something.
We also do not know if it is a family environment or in a company. Any other set of problems can happen in both.
VMware VCP4
Review the allocation of points for "useful" or "right" answers.
-
Client DHCP does not start because of the dependency
Suddenly my laptop IBM T61 Windows XP sp3 Pro link is more to my Belkin router either wired or wireless. This started after I hosted a series of Windows to perform updates. Using the command ipconfig and other signs, it seems that the DHCP process no longer occurs. Research in Non-Plug-and-Play Device Manager, I could see that there was a yellow flag next to 'netBT' which is a dependency for a number of services such as DHCP. Windows suggested I uninstall and then reinstall the netBT.sys "driver". Well, it uninstalled OK but it is now out of the list and without him in charge I'm cut network (I have a Vista laptop second Home that I use on the lookout for ideas tech). I moved a copy of netBT.sys from the SP3 i386 folder in system32\drivers to replace the old, just in case.
How to me netBT to load and work again? I spent several hours restart, activation and deactivation and anything else I could think or find Tech Tips.SOLVED. NetBT corrupt registry entry. HKLM\system\currentcontrolset\services\NetBT
After many hours of detective work, I found the idea in the journal of the events through MSCONFIG. Error type 7001 means service could not start because of a dependency (I knew that), but he went on to say "dir name or path incorrect syntax. I went into the registry and used exactly the same syntax of path as specified in "system32\DRIVERS\netBT.sys" NetBIOS and DHCP service has started.Jim in Arizona
-
Cisco 877W DHCP does not automatically fill the Windows/Mac customers with DNS server entries
I have a 877W which was operational on Verizon for about 5 years. It never automatically distributed info DNS server for customers who get DHCP issued IP address. I have to manually enter the DNS entries to each client. What happened to other sites where I've got installed on AT & T as well as 877 unified communications.
Here is the config. Thanks in advance for the help.
Building configuration...
Current configuration: 7987 bytes
!
version 12.4
no service button
tcp KeepAlive-component snap-in service
a tcp-KeepAlive-quick service
horodateurs service debug datetime localtime show-timezone msec
Log service timestamps datetime localtime show-timezone msec
encryption password service
sequence numbers service
!
Cod of hostname
!
boot-start-marker
boot-end-marker
!
logging buffered debugging 51200
recording console critical
enable secret 5 jSwA $1$ $ 3B5lJNqm0ewh
!
AAA new-model
!
!
AAA authentication local-to-remote login
local remote of the AAA authorization network
!
AAA - the id of the joint session
!
resources policy
!
PCTime-6 timezone clock
PCTime of summer time clock day April 6, 2003 02:00 October 26, 2003 02:00
IP subnet zero
IP cef
No dhcp use connected vrf ip
DHCP excluded-address IP 192.168.7.1 192.168.7.19
DHCP excluded-address IP 192.168.7.70 192.168.7.254
!
IP dhcp pool sdm-pool1
import all
network 192.168.7.0 255.255.255.0
router by default - 192.168.7.1
DNS-server 68.238.96.12 68.238.112.12
!
!
inspect the IP name DEFAULT100 cuseeme
inspect the IP name DEFAULT100 ftp
inspect the IP h323 DEFAULT100 name
inspect the IP icmp DEFAULT100 name
inspect the IP name DEFAULT100 netshow
inspect the IP rcmd DEFAULT100 name
inspect the IP name DEFAULT100 realaudio
inspect the name DEFAULT100 rtsp IP
inspect the IP name DEFAULT100 esmtp
inspect the IP name DEFAULT100 sqlnet
inspect the name DEFAULT100 streamworks IP
inspect the name DEFAULT100 tftp IP
inspect the tcp IP DEFAULT100 name
inspect the IP udp DEFAULT100 name
inspect the name DEFAULT100 vdolive IP
synwait-time of tcp IP 10
IP domain name cods.com
name of the IP-server 68.238.96.12
name of the IP-server 68.238.112.12
property intellectual ssh time 60
property intellectual ssh authentication-2 retries
!
!
Crypto pki trustpoint TP-self-signed-437228204
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 437228204
revocation checking no
rsakeypair TP-self-signed-437228204
!
!
TP-self-signed-437228204 crypto pki certificate chain
certificate self-signed 01
30820254 308201BD A0030201 02992101 300 D 0609 2A 864886 F70D0101 04050030
2 060355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30
69666963 34333732 32383230 34301E17 303731 30313632 33333131 0D 6174652D
395A170D 2E302C06 1325494F 03550403 32303031 30313030 30303030 5A 303031
532D 5365 6C662D53 69676E65 4365 72746966 69636174 652 3433 37323238 642D
06092A 86 4886F70D 01010105 32303430 819F300D 00308189 02818100 0003818D
BF73E16C 24A3FB0B A44C83C8 45ACEC75 163C2F0A 87836F7F A43FEB72 0EF26AFA
C7F35ED6 CBCC6853 5E82B0A6 1FD8020B F3630023 AB30B870 B3155EE6 86988910
4ACF5121 1CBFF4DC B705DF1E 5D0D698F 06493 D 3DD8D036 42 FE450D21 E26A4DAF
CE6BA806 81A9F451 0246698E DA7B49E3 160F115C E1104FA9 31FA3C15 CD 782 279
02030100 01A37E30 7C300F06 03551 D 13 0101FF04 05300301 01FF3029 0603551D
20821E63 11042230 6F64732E 6F666472 63697479 6E677370 69707069 72696E67
732E636F 6D301F06 23 04183016 24 D 77493 80142FA3 03551D 52CF7094 B847B6EB
1385E2E5 0F3A301D 0603551D 0E041604 142FA324 D7749352 CF7094B8 47B6EB13
85E2E50F 3A300D06 092 HAS 8648 01040500 03818100 076EE499 12F46D79 86F70D01
375B7EA6 C9279DA4 B32723B5 908C9FB8 D42CB978 BB24A8FE 73579A3D CA 5130, 87
B7716644 7E13710D C6E6360C D0A36F7B F62540E2 0C33523B E50396B9 2EF66FA7
56519E62 E55EAF3C E1D9BEC9 3AE67B59 75E61F06 B649E90A 2798F755 7A020F0A
F8BDABFA 1EE37B6A A918560D DA45AD70 801BC66E 94D1468E
quit smoking
username privilege 15 secret $5 1jgO$sGD@#l4yTtLtYoEZbh/Wl steal551.
!
!
door-key crypto vpn_ddaus
pre-shared key address 0.0.0.0 0.0.0.0 - key stealthfortyfor5
door-key crypto vpn_rmlfk
address of pre-shared-key 205.30.134.22 key stealthfortyfor5
!
crypto ISAKMP policy 10
md5 hash
preshared authentication
Group 2
!
crypto ISAKMP policy 30
BA 3des
preshared authentication
Group 2
invalid-spi-recovery crypto ISAKMP
ISAKMP crypto keepalive 20
!
Configuration group isakmp crypto VPNRemote client
key ConnectNow45
pool ippool
ISAKMP crypto vpnclient profile
VPNRemote identity group match
client authentication list for / remote
Remote ISAKMP authorization list
client configuration address respond
Crypto isakmp CODS_DDAUS profile
key ring vpn_ddaus
function identity address 0.0.0.0
Crypto isakmp CODS_RMLFK profile
key ring vpn_rmlfk
function identity address 205.30.134.22 255.255.255.255
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
!
Crypto-map dynamic dynmap 10
Set transform-set RIGHT
vpnclient Set isakmp-profile
Crypto-map dynamic dynmap 12
Set transform-set RIGHT
CODS_DDAUS Set isakmp-profile
!
!
MYmap 1 ipsec-isakmp crypto map
defined by peer 205.30.134.22
Set transform-set RIGHT
CODS_RMLFK Set isakmp-profile
match address CODS_to_RMFLK
map mymap 65535-isakmp ipsec crypto dynamic dynmap
!
Bridge IRB
!
!
interface Loopback10
IP 1.1.1.1 255.255.255.0
!
ATM0 interface
no ip address
route IP cache flow
No atm ilmi-keepalive
DSL-automatic operation mode
!
point-to-point interface ATM0.1
Description $FW_OUTSIDE$ $ES_WAN$
Check IP unicast reverse path
inspect the DEFAULT100 over IP
NAT outside IP
IP virtual-reassembly
PVC 0/35
aal5snap encapsulation
!
Bridge-Group 2
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Dot11Radio0
no ip address
no ip-cache cef route
no ip route cache
!
encryption vlan 1 tkip encryption mode
!
SSID tsunami
VLAN 1
open authentication
authentication wpa key management
Comments-mode
WPA - psk ascii 7 14231A0E01053324363F363B36150E050B08585E
!
base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0 54.0
root of station-role
!
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route cache
no link-status of snmp trap
No cdp enable
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 covering-disabled people
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
!
interface Vlan1
Description $ETH - SW - LAUNCH, INTF-INFO-HWIC $$ $4ESW $FW_INSIDE$
no ip address
IP tcp adjust-mss 1452
Bridge-Group 1
!
interface BVI1
Description $ES_LAN$ $FW_INSIDE$
192.168.7.1 IP address 255.255.255.0
IP nat inside
IP virtual-reassembly
route IP cache flow
IP tcp adjust-mss 1412
!
interface control2
IP 70.14.49.134 255.255.255.0
NAT outside IP
IP virtual-reassembly
crypto mymap map
!
local pool IP 10.10.10.1 ippool 10.10.10.254
IP classless
IP route 0.0.0.0 0.0.0.0 70.14.49.1
!
IP http server
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
overload of IP nat inside source list 133 interface control2
!
CODS_to_RMFLK extended IP access list
IP 192.168.7.0 allow 0.0.0.255 192.168.1.0 0.0.0.255
!
recording of debug trap
access-list 1 permit 192.168.7.0 0.0.0.255
access-list 100 remark self-generated by the configuration of the firewall Cisco SDM Express
Access-list 100 = 1 SDM_ACL category note
access-list 100 deny ip 70.14.49.0 0.0.0.255 any
access-list 100 deny ip 255.255.255.255 host everything
access-list 100 deny ip 127.0.0.0 0.255.255.255 everything
access ip-list 100 permit a whole
access-list 101 permit ip 192.168.7.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 133 deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 133 deny ip 192.168.7.0 0.0.0.255 10.10.10.0 0.0.0.255
access-list 133 deny ip 192.168.7.0 0.0.0.255 192.168.10.0 0.0.0.255
access-list 133 deny ip 192.168.7.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 133 allow ip 192.168.7.0 0.0.0.255 any
not run cdp
mymap permit 10 route map
corresponds to the IP 111
set ip next-hop 1.1.1.2
!
!
control plan
!
Bridge Protocol ieee 1
1 channel ip bridge
Bridge Protocol ieee 2
IP road bridge 2
connection of the banner ^ CAuthorized access only!
Unplug IMMEDIATELY if you are not an authorized user. ^ C
!
Line con 0
no activation of the modem
telnet output transport
line to 0
telnet output transport
line vty 0 4
privilege level 15
transport input telnet ssh
!
max-task-time 5000 Planner
Scheduler allocate 4000 1000
Scheduler interval 500
endHello
Can you try to remove the IMPORT ALL of the dhcp pool
RES
PaulSent by Cisco Support technique iPad App
-
DHCP does not work on 877W.-m.
I have a 2nd hand 877W-M, updated the bootloader and iOS for more later.
and now im trying to configure DHCP, as it seems to me, it is done now and should be 'working '.
but I did not at all given ip, and the weird part is that he trows an error just after the command 'write '.
I have also reset the router for ' conf-registration 0 x 2101 ' but when it reloads, it goes to 36 * something.
regarding the error TI trows in after 'write' sound "% IP addresses may not configured on L2 links."
Here's the version on how it works now:
With the help of 3350 131072 bytes
!
! Last modification of the configuration at 07:45:46 UTC Saturday, March 27, 2010
version 15.1
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
877W.-m host name.
!
boot-start-marker
boot the system to boot tftp 255.255.255.255
boot system flash: c870-advipservicesk9 - mz.151 - 4.M6.bin
start the system flash c870-advipservicesk9 - mz.151 - 4.M6
Start flash system
boot-end-marker
!
!
enable secret 5 *.
activate the password *.
!
No aaa new-model
!
Crypto pki token removal timeout default 0
!
Crypto pki trustpoint TP-self-signed-2740876176
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 2740876176
revocation checking no
rsakeypair TP-self-signed-2740876176
!
!
TP-self-signed-2740876176 crypto pki certificate chain
certificate self-signed 01
*****
quit smoking
dot11 syslog
IP source-route
no ip Routing
!
!
DHCP excluded-address IP 192.168.2.0 192.168.2.20
!
IP dhcp pool lan.local
network 192.168.2.0 255.255.255.0
default router 192.168.2.3
Server DNS 192.168.2.3
!
!
IP dhcp dns update
!
no ip cef
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
!
Archives
The config log
hidekeys
0 username cisco password Cisco
!
!
!
!
!
!
!
!
!
ATM0 interface
no ip address
no ip route cache
Shutdown
No atm ilmi-keepalive
CDP enable
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
Shutdown
!
interface FastEthernet2
no ip address
Shutdown
!
interface FastEthernet3
no ip address
Shutdown
!
interface Dot11Radio0
no ip address
no ip route cache
Shutdown
Base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0
54.0
root of station-role
!
interface Vlan1
no ip address
no ip route cache
Shutdown
!
IP forward-Protocol ND
IP http server
local IP http authentication
IP http secure server
!
!
!
!
!
!
!
!
control plan
!
!
Line con 0
exec-timeout 0 0
no activation of the modem
Speed 115200
line to 0
line vty 0 4
password *.
opening of session
transport of entry all
!
max-task-time 5000 Planner
end
IM guess im overlooking something simple, but I don't have experience with router and yet, that's why I bought this type
Hello
-reactivate the ip Routing:
config t
IP routing
-As Paolo said if you want to use the ethernet and wireless, you will have to fill:
Bridge Protocol ieee 1
Bridge IRB
1 channel ip bridge
int bvi1
IP add 192.168.2.3 255.255.255.0
int vlan 1
Bridge-Group 1
Concerning
Alain
Remember messages useful rate.
-
Cells, vCenter Proxy service does not. Qrtz_tables request?
Kia Ora.
Have vCloud 5.5 (latest), vcenter & esxi 5.5u1 in a small 2 host environment.
Just noticed that no one can perform operations that affect the vCenter. Restarted the lot beautifully. No change.
Looked at the topic vSphere resources vCenters and have checked status green, but with the words "error performing operation". When I open it it there was an error "Could not find the cell performing this listening port."
Which lead me to the cloud (2) cells that have no check mark vCenter error "No cells have an ongoing vCenter to run proxy service". Perform a reconnect has not fixed this State.
I remember that 'back in the day' lol, you jumped in the SQL database and discarded around the qrtz_tables. Such as found in this link.
http://www.Boche.net/blog/index.php/2011/12/16/vCloud-Director-and-vCenter-proxy-service-failure/
Someone at - it suggestions? Following this link for vCloud 5.5 would be still valid solution to this problem?
Cheers and have a great day!
the process is still valid for 5.5.x generation.
-
Removal of the firefox proxy settings does not work until a reboot?
If I transfer my work (with a proxy server) to my network network (without server), I have to restart the browser until he realizes that there is no proxy server to authenticate with. Until I do that, (re) loading pages gives me an error.
However, when you go on the other hand, he gently acknowledges that there is a server, and no restart is required before continuing
I have the active automatic proxy settings. I tried to select "no proxy server", but I still need to restart firefox to make it work.
Please upgrade to the current version of Firefox 22.0.
- Help > about Firefox
- https://support.mozilla.org/kb/update-firefox-latest-version.
- https://support.Mozilla.org/KB/updating+Firefox
The version of Firefox 21 that you are currently running is no longer supported with security updates.
- It is important to update Firefox and Add-ons to the latest version to get all security patches.
- FoxyProxy Standard: https://addons.mozilla.org/firefox/addon/foxyproxy-standard/
-
Help! WRT54G2, RELEASE/RENEW DHCP DOES NOT WORK!
Hi, I need help with my router WRT54G2, its been 2 days now that I can't connect to the internet. When I checked my ISP, internet was ok, when I checked my router, release then renew DHCP, nothing on my survivor, I can't get a new DHCP configuration. All I got is '0 '.
Help, please! Thank you!
Thank you guys for help. He is now back to normal, the problem was with our ISP, I published the old IP, but on their end, he pondered again the old IP that I published already. And they have set. Thanks for the help.
Maybe you are looking for
-
15 - ac117tu: "power on password or administrator password.
Help I need help too, I have a HP 15-ac117tuand it appears the administrator password, and when I type something appears Disabled system [I 69778885] Help me
-
Hello Because I did an update of the BIOS on my laptop a few months ago, for some unknown reason maintains close every now & again. A friend told me it might be overheating, but I can hear the fan running all the time, I even looked down so he can ge
-
KDL-55NX810 - "audio system is not available.
I have a KDL-55NX810 TV and I can't get Dolby Digital surround sound to a DLNA served MP4 and the same file on a USB flash drive. The film was HandBraked to MP4 and when I use MediaInfo to display details, it shows that the sound is AC3 and has 6 cha
-
After formatting my lap top I'm unable to connect wifi
The ICON at the bottom right says there is not supported in the system wireless adapters and I can't find drivers for my network controller: s any suggestions?
-
Define 'My task list' as a home page for a specific user
HelloAs long as administrator, I can not put the default homepage to "My list" for a specific user (at the moment of the user's default home page is a blank page and must be 3 steps to get to "My to-do list").I know how to change the home page in the