Proxy title

Similar Questions

• where is my proxy address

  where can I find my proxy address and the code for the printer on the HP officejet 6500 has more

  Hello nyabinghi,.

  If you have already performed the steps I mentioned above and you still have questions, then there may be a few steps, you can try to get this to work for you.

  1. find the IP address of the printer by pressing the icon wireless from the front panel of the printer.

  2. open a browser on your computer that is connected to the same network as the printer. Type the IP address of the printer in the address bar of the browser. (for example http://192.168.1.5)

  3. Once you are in the Web page with the printers settings, click on the tab 'network '.

  4. on the left side of the page, click network address (IP) under the title of networking.

  5. click the button next to manual IP radio and then click on the button 'Suggest a Manual IP address' to have the system assign a manual IP address.

  6. in the manual DNS server boxes, type the following:

  Manual preferred DNS server: 8.8.8.8

  Auxiliary manual DNS server: 8.8.4.4

  7. press the button apply to save these changes

  Once you have saved the manual IP settings you should feed the cycle of the printer by unplugging the power cord from the printer, leaving unplugged for 30 seconds, then reconnect the power cord to the printer. Once connected to the printer should automatically turn on.

  After that the printer is turned back try to enable Web Services again and see if it will connect you.

  Please let me know if this helps your question so I can help you if necessary.

• ip WLAN configuration - missing option to set the gateway and proxy...?

  Hello!

  I need to put the default gateway and the ip proxy addresses after you connect to an access point with wpa2.

  For example my htc incredible may do very well in the installation behind wifi opions.

  I think that he whould do a good idea to config for gateway, dns and proxy server server ip config wlan just after ssid-choosing the Tablet I remember 4 the next connection... a bit like the login made 4 me.

  Could sb here please give me a hint how to solve my problem of connection up there?

  I really like the A1 ThinkPad Tablet after using it 4 about 10 days now... 4 I can fully recommend the purchase and improve my gadget favorite... :-)

  (mod edit: changed the title of the post to match the wire because the question is about the thinkpad rather than the A1 ideapad Tablet Tablet)

  Under settings to go wireless and networks

  under Wi - Fi networks

  Press and hold the connection that you want to change

  Select 'change network '.

  Scroll profile

  Change the automatic to manual Proxy settings

  Enter your settings

  In this place you can also change your DHCP server static IP address

• Web proxy settings are not configured correctly. Have problems with games and other applications.

  original title: apps do not correctly configured

  The default Outlook Express mail, The default Outlook in the Express News with the Internet Explorer Web Proxy are not configured correctly. Because I had problems with the game apps and stuff in my email address.

  Hello

  · You receive an error message or error code?

  You can access the links below:

  How Set Up Outlook Express - and http://support.microsoft.com/kb/2409264

  To configure the web proxy:

  HOW to: Configure Internet Explorer 6.0 as a Web Proxy Client in Windows 2000

  http://support.Microsoft.com/kb/310296

• Keep asking proxy username and password when you try to connect to the internet at the University.

  Original title: keeps asking for password and user name for proxy...

  Hello

  If I connect to the internet at the University that requires a user name and password to use their internet. As a result, this box appears as such:
  http://www.SevenForums.com/attachments/system-security/41870d1260699450-login-pop-up-Windows-security-Inloggen.PNG
  (my box is in English, I found this picture on another forum that seems to have the same problem). The problem is that this Tin can that appear whether or not I am still connected to the uniwide network! How can I fix this annoying box so boring, all 5 minutes, a little hard to watch an upcoming movie...
  I tried to look at proxy Internet explore and that did not solve it.

  See you soon

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the Forum TechNet site:
  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

• In the Internet properties and connections and the local network settings, I uncheck the box for a proxy server, but in a few moments, the computer checks the box

  In the Internet properties and connections and the local network settings, I uncheck the box for a proxy server (because it is blocking my access to Internet Explorer), but within moments, the computer checks the box. What can I do to stop the area of the check proxy server box?

  original title: LAN settings

  Have you checked for viruses?

  http://www.eset.com/us/online-scanner/

  It is very common that the virus to do.

• How to remove the proxy setting

  original title: 127.0.0.1 Proxy address

  In my dial connections, the check box for the proxy server is enabled and the address is 127.0.0.1 with Port 8080.

  If I remove it, it comes back when I connect to the internet again.  Is something worrying?

  I used different virus/malware removal tools and they have not found anything.

  My Earthlink Accelerator does not work very well when I remove the 127.0.0.1

  Thank you!

  Hello

  The line "127.0.0.1 localhost" can be ignored without risk, because it is a standard input.

  Here are the addresses of your computer uses to identify itself, so do not remove them.

  Hope this information is useful.

• Cannot access internet on an android with WiFi Hotspot phone that uses the proxy.

  Original title: HotSpot WiFi Windows 7

  I have a LAN connection and connect to the internet via an address proxy and port on my Windows 7 PC. I want my laptop to a Wi - Fi hotspot so that I can connect with internet on my phone android too.

  Earlier, when I was not using proxy, I used the following command

  netsh wlan set hostednetwork mode = allow ssid = = key

  netsh wlan start hostednetwork

  netsh wlan hostednetwork stop

  Now when I use the proxy, and I use these commands, with success, he created the hotspot and also my phone connects as usual, but it does not load a Web page.

  Help, please.

  Thank you.

  Kind regards

  Aditya

  Hi Aditya,

  Thanks for posting your query in Microsoft Community. According to my research Internet on android apps may not work if the proxy is enabled.

  The browser you use to access the internet on your mobile phone?

  The information of IP address, gateway, subnet mask of your operating system to Windows 7 and configure the internet manually using this information (on your android phone) and check if the internet works fine.

  For assistance to the configuration or to find the settings, contact support android.

  https://support.Google.com/Android/?hl=en

  Hope that the information provided is useful. Do not respond if you need more help.

• My browsers to stop randomly. It started after the installation of a proxy called Freegate.

  Hi, I think I have a problem with the network now.
  Problem is that the internet browser (both Google Chrome and IE 8) sometimes.

  Well, in fact it works, but the orb keep circling for chrome and ' Waiting for X "for IE 8.
  Even I wait several minutes, web page appears. (White screen)
  But when I update SEVERAL times (not once), it works.

  This thing started to happen after I used the proxy (I don't know not for you. Maybe VPN) program called "Freegate".
  I deleted this program shortly after that I found this problem happening.

  This could be the problem when I'm filling some sort of form on. And I must do it again...

  I'd appreciate any help.

  original title: network problem

  Hello

   
  Perform the clean boot and check
   
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: After the boot minimum troubleshooting steps, follow step 7 link to return the computer to a Normal startup mode.

• problems connecting to the wireless network - the network (no internet access) proxy setting

  Former title: yellow triangle wireless

  My computer can connect to the wireless router but cannot connect to the internet. I try to connect with the ethernet with cable modem connection & it still does not work. The other laptop works fine but my does not.

  1. I have uninstalled & installed the network card.

  2 restart the apater modem & network cable

  3. I get 'Windows could not detect a network proxy setting.

  4. when I "Network & Sharing Center" and under "show your network activity" I get "identification."

  5. "identiyfing netgear" below said 'no Internet' when you are connected to netgear

  Windows IP configuration

  The host... name: Jeffrey -.
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Virtual WiFi Miniport adapt
  Physical address.... : 1C-65-9D-BF-E2-BF
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  Description...: Realtek RTL8188CE WLAN 802.11n PCI-E NIC
  Physical address.... : 1C-65-9D-BF-E2-BF
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::cc8f:f2cd:dd7c:ccd1% 17 (Preferred)
  Autoconfiguration IPv4 address. . : 169.254.204.209 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  DNS servers: fec0:0:0:ffff:1 1%
  FEC0:0:0:FFFF:2 1%
  FEC0:0:0:FFFF:3 1%
  NetBIOS over TCP/IP...: disabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  Description...: Realtek PCIe FE Family Controller
  Physical address.... : 1C-75-08-73-8F-F1
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {342574F9-0D0B-4337-B59D-E7373E959066}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {25F2C90C-9E95-491A-BDFC-4F4CDA2FE33D}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Adapter Microsoft ISATAP #2
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 12:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Hi istraight1,
  a few steps, I recommend you to see exactly what this question:
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  and
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/Windows-could-not-automatically-detect-this/d243dea1-d1c8-4C4A-ba96-2b49bc9bab1a?TM=1338167520088

  and finally:
  http://social.technet.Microsoft.com/forums/en-us/itprovistaprinting/thread/548ca07e-F04E-4973-8719-8c09959f1ca6hope this helps.
  B Eddie

• Error message: "Windows Media Player cannot access the file. The file may be in use, you won't have access to the computer on which the file is stored, or your proxy settings are may not be incorrect. »

  Original title: problems of residential group after system recovery

  I started a homegroup on my computer.  I added another computer to the homegroup.  Everything worked fine until I had to perform a system recovery on the laptop that I used to start the homegroup.  I implemented the homegroup again, but I can't access the files on the other computer via Windows Media Player.  I get an error message that says "Windows Media Player cannot access the file. The file may be in use, you won't have access to the computer on which the file is stored, or your proxy settings are may not be incorrect. "I can access all the music files via Windows Explorer.  I have to start over with a new password?  Can I just create a new homegroup?  What other options do I have?  You can provide any help would be greatly appreciated.  Thank you.

  Hello

  Please follow the methods and check the issue:

  Method 1:

  Open the homegroup troubleshooting utility:

  http://Windows.Microsoft.com/en-us/Windows7/open-the-HomeGroup-Troubleshooter

  Method 2:

  Why can't I access my homegroup? :

  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-access-my-HomeGroup

  For reference:

  Homegroup: frequently asked questions:

  http://Windows.Microsoft.com/is-is/Windows7/HomeGroup-frequently-asked-questions

  Method 3:

  See the steps in "include a folder shared in a library" from the link below:

  Access to files and printers on other homegroup computers: http://Windows.Microsoft.com/is-is/Windows7/access-files-and-printers-on-other-HomeGroup-computers

  I hope this helps.

• Window can not automatically detects the network proxy settings

  Original title: window could not automatically detect the network proxy settings
   
  Windows network diagnostics says constantly "" window could not automatically detect the network proxy settings"" How can I fix it I have a Windows laptop, 8 and I can't use the internet, most of the time, but the internet bars are full and there is no yellow triangle with a! next to him.  Usind Ethernet instead of WIFI makes not much difference if you please, help.

  

  

  Hello Sarandeep Singh,

  Thanks for your reply Sarandeep. Now, this problem has been resolved. I that follows the steps of: https://support.microsoft.com/en-us/help/15287/windows-why-can-not-get-connected ( run Networking command after using the convenience store network )

  Thanks again.

• Cannot use Internet Explorer and Windows Store, error messages "proxy server is unresponsive and we could not connect to the Bank.

  Original title: store in connection to wide band BSNL

  I browse the Internet via a broadband BSNL connection. I have no problem accessing internet through google chrome, but IE does not open web pages saying "proxy server is not responding", shop said "we were not able to connect to the Bank. This could happen because of the connection to the server or the connection timed out." How to solve this?

  Hi Laurent,.

  Glad to know the steps described in the previous post has helped you.

  To solve the problem with Windows Store, I suggest you try these methods.

  Method 1:

  Let's first try run the troubleshooter modern UI App and check if it helps.

  http://download.Microsoft.com/download/F/2/4/F24D0C03-4181-4E5B-A23B-5C3A6B5974E3/apps.diagcab

  Method 2:
  If the problem persists, I suggest you make sure that the date and time are correct on the computer.

  (a) check the Date/time setting by selecting the tile of office , then left click on the date/time in the corner.

  (b) click change date and time settings. And then check zone is correct as well as the internet time tab has the ability to synchronize with the time server Internet.

  See the article for more information.

  What to do if you have problems with a soft

  http://Windows.Microsoft.com/en-in/Windows-8/what-troubleshoot-problems-app

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• Connection to the store of Windows without turning off the proxy settings.

  Original title: do not connect not not in the windows store

  It's been 2 months since I bought my laptop from sony with windows 8. not once it is is connected to the store or any other windows app despite the repeated attempts by the evolution of the proxy settings. Don't ask me to try to disable the proxy settings, because it's the only way I can have access to the internet. Please solve this problem as soon as POSSIBLE, or if not I'll have to switch to another mode of system.not only store I couldn't even connect to any windows app given.i have not yet updated my windows up to now.
  I tried each and all solutions that was posted on this issue.please suggest me proxy or any other solution parameters.

  Hi Jagan,

  1. When you say repeated attempts to change the proxy settings, have proxy settings you tried to change?

  2. your computer connected to a domain is?

  3. you receive messages or error codes?

  This problem could be due to some incorrect settings or because of the connection proxy you use.

  Using a proxy server can allow the administrator to limit access to the Internet.

  You can reduce the effect of these problems by allowing unauthenticated through your proxy server access. We recommend that you enable unauthenticated access only for connections to URLs used by each application that has a problem. Some proxy servers may suggest that you create a list of URLs (also known as the 'white list') permissions.

  Please refer to the article to address these issues that relate to the use of Windows Store apps or use of Microsoft applications that are included with Windows Update or Windows 8, you can include the addresses mentioned in the article in a list of permissions ('white list') on your proxy server and enable HTTP and HTTPS access for them :

  The use of proxies authenticated with Windows 8

  For more information, see the article:

  Using the Proxy selection and Proxy bypass lists

  You can also consult the steps by Rajesh Govind, Support Engineer, may 4, 2013 and check.

  Windows 8 apps not able to detect the proxy for my machine settings.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• Proxy for ERPIntegrationService

  Hello

  I'm working on the client proxy code for the ERPIntegrationService tests. I am following the steps mentioned in " " By using the Services of external to Oracle ERP Cloud.PDF data integration "published by Oracle. " The automatically generated ObjectFactory does not include some such methods mentioned in the PDF document. For example, createDocumentDetailsContent shown in the following excerpt is not available. So can't go further. I use Jdeveloper 11.1.1.7. Help, please.

  ObjectFactory objectFactory = new ObjectFactory();

  DocumentDetails documentDet = new DocumentDetails();

  String NomDuFichierAvecCheminComplet = "C:\\Temp\\Sample.zip";

  String fileName = "Sample.zip."

  String contentType = "zip";

  String title = "import magazines."

  String ucmAccountInfo = "end$ / generalLedger$ / import$ ';

  String ucmSecurityGroup = "FAFusionImportExport";

  documentDet.setContent (objectFactory.createDocumentDetailsContent (getByteArray (fileNameWithPath));

  Thank you

  Maria

  Problem solved. Recoded as shown below and it compiles:

  documentDet.setContent (getByteArray (fileNameWithPath));

  Thank you

  Maria