Question of Ralink adapt - RT3290

Similar Questions

• Adapter Ralink WiFI RT3290 802.11 bgn

  Hello

  I just bought a laptop from HP ENVY 15.  And preinstalled * beep * in windows 8.1

  15 - j118so

  G1N98EA #UUW

  I have uppdated the driver for wireless for later, but I can't see any network in 5 GHz, only 2.4 Ghz.

  My question is: this network card supports 5 Ghz?

  It is said 802.11bgn and why I bought it, so I could use 5 Ghz, but I don't see any of that s.

  Hello:

  The Ralink RT3290 802.11 bgn is the only map of a single band (2.4 GHz).

  Whenever you see a Wireless N card specification listed as bgn, it is a single band card.

  Cards dual band are listed as abgn or agn.

• Question about faulty adapter and warranty

  Dear community,

  I would like to ask for your help, because I am not fully aware of the security regulations.

  My Toshiba laptop charger is seen error contact for a long time, but I need on a daily basis of the device, and at the gas station, I was told that I have to give my computer laptop too at least a week.
  I don't have enough money for a new charger, but maybe I could fix it.

  My question is that if I fix the charger, will I lose my warranty for the device in the laptop too, or just the charger?

  I thank in advance for your answers is, it is really important for me.

  Hello

  Laptops as well as the laptop parts are covered by the standard warranty.
  AFAIK the laptop as well as parts must be repaired by the authorized Toshiba service provider to keep the warranty valid.

  I m not very good if an adapter can be repaired. I think that this part would be simply replaced. So if you have a defective power adapter, I recommend you contact the maintainer authorized Toshiba in your country to get a new part.

  Also, you should be aware that the use of defective parts (power supply, for example) can damage additional parts like laptop's motherboard and this could lead to expensive repair procedures.

• Pull on the question of the adapter

  Hello

  I use PULL adpater in FDM which works very well.

  Is the question that I see, if I try manually change value target in the card, said member of the invelid.

  So shoot adpater will no not a target application to validate againtst members. But, why I'm not able to manually update the value in the cards.

  From now on, I am deleting and reloading whole card if I need to change the value of a member. Do us hv no work around for this problem.

  Thanks in advance

  
  

  Yes, disable the "Use list" option on the dimension of the adapter:

  (a) connect to the application via the workbench

  (b) expand the adapter > Dimensions

  (c) make a right click on a dimension active and choose "Properties".

  (d) uncheck the "use list" option and save.»

  (e) repeat for each active dimension.

• Question of discards adapter Essbase

  I have a question,
  When you use FDM to load data into Essbase rejection of export displays only the first member met that caused a problem. This is a problem because you need to update metadata, redeploy the application and relaunch export after each single release.
  
  is it possible to receive all releases at a time, so that you have only to make the redeployment and update task 1 time?
  
  
  (this is hyperion version 11.1.1.3 using the essbase for FDM adapter)

  One method is to take your Outbox .dat file and write a rule to load in essbase to load the file. Aside from that, I think you need to change the adapter of fdm code itself.

  A realistic once you have loaded your initial, then all rejected records happen to step 2 of the FDM process and this will give you a screen for those who are not mapped you can export to Excel and work on the update of your Essbase metadata, if there are new entries.

  Kind regards

  John A. Booth
  http://www.metavero.com

• Question on AC adapter & plug on Satellite A300

  Hi all

  I bought a new Toshiba Satellite A300-1ec almost 20 days, yesterday, when I plugged the cord to charge my cell phone, I find that it works well. When I went to the supplier he said that n adapter cord with plug is burnt, can this happen with a new, now what should I do... to get it replaced, or where can I find a replacement for her

  Kind regards

  Mathew

  Hello Martin

  Please contact the nearest service provider authorized as soon as possible. Explain the situation and they will help you. Please check http://eu.computers.toshiba-europe.com > support & downloads > find an ASP and you will find the addresses and phone numbers.

• Satellite Pro 6100 - Question on WLAN adapt and mac address

  I bought a second hand of Satellite Pro 6100. It has a WiFi adapter. It is where and how do I know the macadress of the adapter?

  Thank you.

  Hello

  If you are sure that this laptop was equipped with the Wlan card, and then the MAC address can be easily discovered 100%.
  You must start the console with the command: * CMD *.

  Then use the command: * ipconfig/all *.
  This would list all the details on the WLan/LAN cards installed in the laptop.
  The physical address means MAC address ;)

  This should help!

• Question of power adapter (T410 2537-DN1)

  I have a thinkpad T410 (2537-DN1) and my original power supply is to see some wear and tear that I temporarily fixed with electrical tape. My card is currently a 60W/20V model. What I am asking is that I still have my old T60 adapter. It is a 90W/20V model. Can I safely use on my T410? My search found two yeses and no suggestions but nothing solid. ERGO, I thought I'd ask.

  Thanks in advance,

  Kate

  None!

• Question of helmet/adapter for blackBerry Smartphones

  I have a wired headset that I used with my old phone Kyocera that I love... y at - it an available adapter to adapt this up to 3.5 mm headset that uses the BB? I was doing a search online and have not been able to find one. I don't really know what is the size, but I know it's quite a bit smaller than the 3.5 mm.

  Thank you!

  What is a record 2.5?

  You might find a device that connect it properly to determine exactly which adapter you need.

  http://www.yourcablestore.com/25mm-Stereo-female-to-35mm-male-Adapter_p_220.html

• Question of FDM adapter in version Hyperion 11.1.2.2.

  Hi all
  
  I created a HFM and Application of FDM.
  Set all parameters in the application of FDM, but when I opened control tables am getting error.
  
  Cannot retrieve the data on the target system
  
  Please help me that you know about it.
  
  Thank you
  Mady

  Thank you all for your responses.

  Problem solved. We must enable custom dimensions, 3 and 4 so will connect us to HFM using FDM.

  Kind regards
  Mady

• laptop HP pavilion g6: ralink rt3290 802.11bgn wi - fi adapter problem does not not when turn on pc

  Hi iam using windows 8 64-bit HP pavilion g6 my adapter ralink rt3290 802.11 wifi bgn does not work for a few days because of the sudden closure of the pc by the battery problem, whenever it's strcuked reason more to heat or liquidated suddenly drops ralink adapter not worked for some time, now it not group days I updated my driver of latest vesion by the Device Manager in windows to the latest version still problem persists, I have to reinstall it

  Hi @eswar_krishna,
  
  I hope you enjoy your visit to the HP's Support Forums. I understand that you have a problem with the wifi adapter. I'll be happy to help you.

  The following pages are useful for troubleshooting wireless connectivity problems.

  Troubleshooting wireless network and Internet (Windows 8)

  In addition, you can watch the the power management of your wireless adapter:
  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.
  
  Forget the network: (Windows 8)
  1. press Windows Key + C
  2. click on settings.
  3. click on change PC settings.
  4. click on network on the left.
  5. click on manage known networks.
  6. click on the name of the network.
  7. click on forget.
  
  Reset TCP/IP on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.
  
  It can also help to reset the Winsock Catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.
  
  Reinstall the NIC drivers:
  1. download the drivers from here, but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.
  
  Test an ethernet connection:
  Not call explanation. Test if the problem persists on a wired connection to the adapter hardware troubleshooting wireless can be directed to the appropriate areas.
  
  Test another connection:
  Many people excluded their home network as a problem if another device working on the same network. Networking is not as simple as that. Each device interacts differently with your router or modem and it is impossible to exclude the settings for this device until the laptop has been tested on another network.

  Please keep me informed of the progress of things.

  If you need help, let me know and I will gladly make all that I can to help you.

  Please let me know if that solves the problem by marking this post as "accept as a Solution.
  To simply say thank you, click the Thumbs up below!

  Thank you.

• Don't load not satellite L550 - cannot use the AC adapter

  Hey guys I'm stuck.

  My L550-113 collapsed somehow load.

  He was supported very well now and then, sometimes stopped to load.

  When pluged AC the yellow control light lights up for a few seconds then Amber transforms into a yellow flashing.

  Tried to unplug and plug the AC adapter it did charge twice but now even that doesn't help.

  My main problem is that I can even use the device when it is pluged in...

  What should I do?

  Hello

  Remove the battery and unplug the AC adapter.
  Wait several hours and then connect the two parts and check if the laptop to charge again.
  If this isn't the case, then the adapter should be verified.
  If it s question no AC adapter (I guess that he isn t ac adapter related issue) then the motherboard of the laptop must be verified.
  I think that security is still available so get in touch with the local ASP in your country!
  Guys should help you.

  Welcome them

• Engine for MyRio adapter command 2 DC motors

  Hello

  I have a question about the adapter engine for the MyRio. I found the following code example:

  https://decibel.NI.com/content/docs/doc-45592

  This afternoon, I was able to drive a motor continuous using this VI, but I want to use to control 2 Motors continuous. I tried the following (see photo) and it did not work.

  What should I do for the second DC motor?

  Thank you!

  Hello

  Well, the next time you post, it would be useful to have all the information to start with (what does your system, errors, measures

  you have taken to solve the problem, etc.). This way more people will respond and we can help you more easily.

  By parallel loops, I just run two processes in separate loops at the same time in the same VI (what they do on the link).

  If you think about it logically if this initial process is running one engine, then do the same exact process but that it points to the

  second motor will run the second engine. So, if you include the two pieces of code (exactly the same but different engines references) in the same VI then it can run two engines.

  If you look at the link I have attached before she speaks of two ongoing processes at the same time within the same VI.

  You can then use queues and the authors of the notifications (look in them) to communicate between the two processes you use, allows from Control Panel even before to control them and stop them both at the same time.

  With this, you should be able to all both enforce.

  Hope this helps

• HP ENVY23: PROBLEM WITH A WIRELESS ADAPTER

  Hello

  I BOUGHT THIS REFURBISHED DESKTOP PC. ITS BEEN WORKING REALLY WELL FOR PAST 1 YEAR, BUT SUDDENLY, NOW HE BEGAN TO HAVE PROBLEMS WITH A WIRELESS ADAPTER THAT IS RALINK ADAPTER. PROBLEM IS THAT ADAPTER WILL SUDDENLY STOP WORKING. SO I HAVE TO GO INTO THE DEVICES AND ADAPTER MANAGER DISABLE AND ENABLE FOR HER WORK ONCE AGAIN. SOMETIMES EVEN THAT DOESN'T WORK SO AFTER RESETTING THE ADAPTER, I HAVE TO TURN ON/OFF THE COMPUTER. I HAVE NO CLUE AS WHAT THAT CAUSES THIS PROBLEM. PLEASE IF ANYONE KNOWS HELP.

  Thank you

  AHMED

  P.S I JUST TRIED TO UPDATE MY WIRELESS ADAPTER DRIVER.IT ME SAID I HAVE ALREADY UPDATED DRIVER INSTALLED.

  Hi there @JUMRONI

  Welcome to the Forums of HP Support! It's a good place to find the help you need, so many other users, the HP experts and other members of the support staff.

  Please report the number of complete product for your computer. Check out the following, if you need assistance with this information. How can I find my model number or product number?

  I suggest to start by checking your system for malware, as follows:

  HP computers - solve and protection against viruses on your computer (Windows 8)
  Spyware, Adware and browser hijacking software

  If that fix it, you're done, otherwise, you should check these:

  Troubleshooting wireless network and Internet (Windows 8)
  In addition, you can watch the the power management of your wireless adapter:
  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.

  Forget the network: (Windows 8)
  1. press Windows Key + C
  2. click on settings.
  3. click on change PC settings.
  4. click on network on the left.
  5. click on manage known networks.
  6. click on the name of the network.
  7. click on forget.

  Reset TCP/IP on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.

  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.

  Reinstall the NIC drivers:
  1. download the drivers from here, but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.

  Test an ethernet connection:
  Explicit. Test if the problem persists on a wired connection to the adapter hardware troubleshooting wireless can be directed to the appropriate areas.

  I would like to know if this works for you.

• T410 - using the Hard Drive Bay adapter III series

  I have looked in getting more storage data on my t410 and had a few questions about the adaptation of the dvd to the HARD disk to use. (1) the t410 certainly does support the adapter? (2) will the adapter supports all 9.5 mm HDD 2.5 "? can I use a 7200 RPM drive? (3) this configuration supports protection against shock, as the HARD disk drive Bay original? (4) is there anything else I should consider? THX in advance

  ended up finding the Hitachi Travelstar 2.5 750 GB 7200 RPM SATA II 16 MB Cache internal hard - 0S 03339 and Thinkpad Sata HD Bay adapter 3, both from Amazon. the model # on the Amazon unit is the same as the one on the Lenovo site, but was $30 cheaper. Ran $89,99, vs. $61,17 for the 500 GB Hitachi 750 GB... I hope it works like the 500 GB