Questions to access the router Netgear WNDR3400 of laptop Readyshare USB disk 64-bit Windows 7

Similar Questions

• When Photosmart C6380 connects to the router Netgear WNDR3400, internet connection lost.

  Using HP Photosmart C6380 wireless connection to a Netgear WNDR3400v2 router.  When the printer is on, all devices of lose the internet connection, but can be crazy.  Network WPA2 authentication. the printer shows WPA authentication configuration page so maybe that's the problem.  How can I keep my internet access while the printer is connected to the network?

  FRST, make sure that your router has the latest firmware.

  Let's define an IP address static and exeternal DNS of the printer:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

  After that, you will have to redo 'Add printer' using the new IP address.

• Access the router cant admin homepage

  I can't access my router admin page.

  I tried this: 192.168.0.1 192.168.1.1 www.routerlogin.net www.routerlogin.com, I used google, internet Explorer...

  model of router: wndr4500

  Can you help me?

  Kind regards

  Xander

  Assign you a static IP address on the computer?

  If you have set it to static, back to obtain an IP address automatically.

  The two IP addresses must be in the same range.

  It is recommended that you access the router admin page using a computer that is connected directly to the router.

• WRT1900AC: Cannot access the router remotely

  This can be a simple, but I'm scratching my head on it.

  I just took a 1900 for my personal use at home. I did a basic auto config (Nothing fancy, just Plain Jane).

  As part of the configuration process, I associated the router to a Smart Access account that is different from that assigned to the routers in my church.

  For some unknown reason, I can not access the router using the Smart app unless I am accessing Internet through the 1900. If I have Internet access through my Verizon FiOS router, the Smart application tells me that my wireless router is offline.

  I missed the 1900 and started from scratch using my office... again... combining the unit on the account. Once again, no luck.

  I have a session with my smartphone and tried again with my tablet. Still no luck.

  Just to make sure that there is no failure, I tried to access the routers of the Church... and has been able to do without any problem.

  Y at - it an option that I forget? I don't remember running into this situation when you configure the 6500 s and 6900 s.

  10,168 is also a private IP address.

  I recommend that you enter this address that you see on the WRT router in DMZ ISP modems. If there is a reservation on the ISP modem function, book it as well so it can't change it later. This will keep the DMZ address for the WRT router and you should be good here.

• Windows 10 devices cannot access the router settings (R6250) page

  So, after several hours of troubleshooting (reset the router, firmware flashing, try several devices) I think I discovered why I get the message '192.168.1.1 refused to connect': 10 Windows. All devices not - 10 Windows can connect to Settings page fine, but all of my Windows 10 devices fail and get this message. And on my laptop, it gets the message refused on Windows 10, but when I rebooted the router and tried a linux live usb on the laptop, it connected to the page of the parameters very well. So I think it's some kind of problem between Windows 10 and the router.

  Anyone has any advice on how to fix this? I need the settings page to run on Windows 10 as it is the main operating system I use.

  Thank you!

  Have you tried different browsers?

  Try turning off the Windows Firewall, temporarily.

• Cannot find the driver for a PSC 2175 in list of 64-bit Windows 7 for HP printers

  Cannot find the driver for a PSC 2175 in list of 64-bit Windows 7 for HP printers.  Can anyone help?

  In fact, the way to solve the problem was to open devices and printers, click with the right button on the icon of the HP psc 2170 Series and use troubleshooting icon.  Who finds the driver, thank God.  Found this just by chance!

• I accidentally deleted the directory "C:\Program Files (x 86) \Microsoft ' my 64 bit Windows Vista system. How can I get it back?

  I accidentally deleted the directory "C:\Program Files (x 86) \Microsoft ' my 64 bit Windows Vista system.  How can I get it back?

  original title: C:\Program Files (x 86) \Microsoft

  You can try this program:

  http://www.filehippo.com/download_recuva/

  Use the deep Scan option. It may take some time.

  The System File Checker can repair some of the files in there, but probably not all.

  It's probably at least some of the files that have been overwritten. so I would say the the more safe thing to do is to reinstall Windows.

• FF 15.01 cannot access the Admin Page of the router (Netgear WNDR3700)

  I can connect to the page, the page log, and it displays all forms on each page of settings, however, the current settings are not filled and I can't make changes.

  Error console shows a bunch of error messages like:

  Timestamp: 15/09/2012 20:35:32
  Error: Exhibitor chrome JS objects to the content without __exposedProps__ is fragile and obsolete. See https://developer.mozilla.org/en/XPConnect_wrappers for more information.
  Source file: resource://jid0-lmznvk7a82o8cufhdfb9dudfa2w-at-jetpack/api-utils/lib/cuddlefish.js-> resource://jid0-lmznvk7a82o8cufhdfb9dudfa2w-at-jetpack/api-utils/lib/sandbox.js-> resource://jid0-lmznvk7a82o8cufhdfb9dudfa2w-at-jetpack/api-utils/data/worker.js
  Online: 130

  whenever I have call the page.

  I chose to activate JavaScript and Java. It seems that a worsening of the problem associated with the list and to be able to run buttons in web messaging to my Web host company, Infoquest.com (indicated for FF4. and later, never addressed bee). Each new rev of FF also seems, to increase the number of existing web pages that FF can't manage properly, especially the script-based and interactive pages such as the Hewlett Packard Support Community Forums - you can type a message to all you want, but FF will leave you not to run the 'Post' button

  NOTE: this has just started in 15 FF. Until that moment, I had 'normal' access and control of the router. Now, I have to use IE 9.

  (Win 7 64-bit, sp1)

  Hello wmcole, the error message you quoted is triggered by one of the addons that you installed - although I don't know if this is the origin of the problems on the web interface of the router. Please, try to start firefox in safe mode once and see if the problem occurs here also.

  Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox

• M40X connects to the router Netgear DG834G wireless

  Message on the toolbar and warnings are; No limited connectivity or. Improved Intel Pro wireless 2200BG driver worm 9.0.4.8 without success.
  I have another laptop with a USB wireless network too and that works very well.
  I was able to connect to the router via the ethernet card.
  Been on Netgear, and the router works well.
  Any ideas, anyone please...

  Hello

  I guess that your laptop uses the map Intel 2200BG wireless.
  You will find a lot of questions and problems with this card intel.
  Mainly the graphics driver update will solve these issues.
  You can also check the power save mode settings in the properties of the wireless card. Go to the Device Manager, choose the wireless card and go to properties. In the second Advanced tab you should find the Power save mode option. Please switch off (off)

  I put t know where you download the driver, but you must use the latest version on the Intel site.

• Wmp300n connection to the router Netgear WGR614 G problems

  I'm new here so I want just to say hi first.

  I've been lurking here for a while because I bought my 300N. So far, the monitor is undesirable now it is uninstalled and all the drivers are installed. When my DD - WRT flashed WRT54GL is my main router this card is ideal. But I have another problem with two Xbox 360 who do not want to use the same service at the same time, so I bought another router. The Netgear WGR614 v.9.

  I have the 54GL router on a bridge wireless for the 360 so I can have both on the net at the same time. Even when the netgear router is the main router... This 300N wireless card has worked with him for about 10 minutes then just loss of signal. It will not reconnect no matter what I do. I reinstalled it and it still does not connect. The 54GL router is connected to it very well and works.

  There is a problem with the Netgear router what is the map?

  Please if anyone knows that would be great for a response. All forums I go I always ask difficult questions and they never get answered. haha.

  UPDATE: it turns out that it is the fault of WRT54GLs. The DD - WRT software cannot do the job of a customer right wireless I guess. The Netgear router shows that it gives two IP addresses when the router connects with the xbox. It gives the IP router and the xbox and the INVESTIGATION period. But then show that they share the same MAC address. DD - WRT is the MAC of the XBOX and the same as making the MAC like DD - WRT. And no matter how many times I change the MAC it they are both the same to come.

• can not access the router (192.168.1.1) of the browser firefox web

  When I try to access my RV042G Gigabit Dual WAN VPN router from firefox or chrome I get an error message

  > An error occurred during a connection to 192.168.1.1. SSL has received a low ephemeral Diffie-Hellman key in the handshake message exchange the server key. (Error code: ssl_error_weak_server_ephemeral_dh_key)

  I had a similar problem with the storage attached network (Synology Diskstation) unit but I was able to create a certificate that meets the "modern standards" and the problem was solved.

  I need to create a new certificate for the web server on the router RV042G?  How?

  FYI - running firmware 4.2.3.06

  Thank you

  Lee

  Hello Lawrence,.

  Thank you for using the small community of Support Business!

  It is a known problem that affects a number of products for small business. There is another post which lies here who has some solutions you can try.

  If you have any other questions, please post them here and I'll do my best to help you!

  Best,

  Taylor

• "Bad Gateway" EA4500 try to access the router after installation the software upgrade

  Hello, I have recently updated my installation software to Version 2.0.14212.1.  I realized that I had to upgrade the installation software before upgrading the Firmware to version 2.1.41 (Build 164606).  However, since the upgrade of the installation software, I could not connect to the router on any browser (Firefox and Chrome).  Instead, I get the error message "-502 Bad Gateway.

  To add to what chadster766 suggested, after pressing the reset button for 30 seconds, try to turn off the router to give him time to rest. After a while, it turns on and plug a PC for it. Try to access the configuration again to 192.168.1.1 page.

  Hope that helps.

• Unable to access the router configuration

  I have a problem accessing my WRT54G Router configuration screen

  I tried to reset it by default (pressing the button of reset for 30 sec.)

  However, the default connection information does not work for me (username: empty password,: admin)

  Can someone help me?

  Hi shopping,.

  You can download the file to the router firmware WRT54G version 7 from this link:

  Click here

  Hope that helps. :-)

  Good luck!

• WRT610N question to access the data on the NAS

  Hello

  Just replaced my WRT54G (works perfectly) with a WRT610N and used the same configuration to access Internet and LAN.

  Upgrade to the latest Firmware for the 610N.

  The WRT610N that is connected to a SD2008 (1 GB of Linksys 8 - port Switch).

  SD2008 connected to a Synology DS209 + with the latest Firmware and PC XP. Access between PC and DS209 + works perfectly.

  WRT610N connected to a couple of wireless devices; such as iPhone, Vista and XP PC and wired for PS3.

  When you access any device (PC, PS3) through WRT610N, I see all the directories and content even as thumbs on DS209 +. Try to open or to copy one takes file (2 MB in size) incredibly long (about 3 minutes). .

  Copies of Vista or XP PC wireless to DS209 + large works and same file is copied in a few seconds. Internet download works fine with good performance as well.
  WRT610N with NAT enabled; Firewall disabled.

  Any suggestions or solutions?
  Thank you

  This is it.

  Bought new cables - same question, MTU has changed - same question. Changing the port on WRT - BINGO.

  Looks like Port 1 is defective,

  Thanks for your help amine.

  Concerning

• Cannot access the Router #2

  Here is a diagram of my home network.  This is what works.  If I have a device (phone or laptop) connected to the #2 router (wired or wireless), I can browse my network devices and browse the Internet without any problems.  My problem happens the other way.  For example, if I have a device (phone or laptop) connected to the #1 router (wired or wireless) I can see all network devices, with the exception of #2 router and all devices connected to it.

  Starting from a device connected to the Router 1 # I can ping LAN ports and Internet #1, #1 wireless bridge and Bridge #2 wireless router.  However, I can not ping the Internet port on the Router #2.  I guess it's a setting on Router #2 just don't have yet.   Here is a list of my equipment:

  Wireless routers are the two Linksys WRT 54 G

  Wireless bridges are the two Engenius ENS202

  Any ideas on why this is happening?

  

  Turn your router n ° 2 in a switch\repeater.

  Changes required for the installation of WRT610n:

  1. Change the SSID of the evocative wireless for the location. Ex: UpstairsWifi
  2. This must be done at the same time on the configuration screen, change the IP address of the router to 192.168.1.254 for you there is an IP address conflict with your main router, disable DHCP and save the settings
  3. Don't forget after that point that the internet port of the router is not to be used only the LAN ports
  4. If you need to reconfigure this router you would use it's new IP address in the browser "192.168.1.254".

  This means that your network IP addresses range starts with ' 192.168.1.. " If not the typical another range of IP addresses would begin by "192.168.0. * ' in which case the router's IP address must be changed to 192.168.0.254