Windows 10 devices cannot access the router settings (R6250) page

Similar Questions

• Error message: "Windows Media Player cannot access the file. The file may be in use, you won't have access to the computer on which the file is stored, or your proxy settings are may not be incorrect. »

  Original title: problems of residential group after system recovery

  I started a homegroup on my computer.  I added another computer to the homegroup.  Everything worked fine until I had to perform a system recovery on the laptop that I used to start the homegroup.  I implemented the homegroup again, but I can't access the files on the other computer via Windows Media Player.  I get an error message that says "Windows Media Player cannot access the file. The file may be in use, you won't have access to the computer on which the file is stored, or your proxy settings are may not be incorrect. "I can access all the music files via Windows Explorer.  I have to start over with a new password?  Can I just create a new homegroup?  What other options do I have?  You can provide any help would be greatly appreciated.  Thank you.

  Hello

  Please follow the methods and check the issue:

  Method 1:

  Open the homegroup troubleshooting utility:

  http://Windows.Microsoft.com/en-us/Windows7/open-the-HomeGroup-Troubleshooter

  Method 2:

  Why can't I access my homegroup? :

  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-access-my-HomeGroup

  For reference:

  Homegroup: frequently asked questions:

  http://Windows.Microsoft.com/is-is/Windows7/HomeGroup-frequently-asked-questions

  Method 3:

  See the steps in "include a folder shared in a library" from the link below:

  Access to files and printers on other homegroup computers: http://Windows.Microsoft.com/is-is/Windows7/access-files-and-printers-on-other-HomeGroup-computers

  I hope this helps.

• Error when you try to play audio files: Windows Media Player cannot access the file. The file may be in use, you won't have access to the computer where the file is stored

  Windows Media Player cannot access the file. The file may be in use, you won't have access to the computer on which the file is stored, or your proxy settings are may not be incorrect.

  I hope someone can help on Win 7 64 bit, music is taken on a disk usb2 external hard... I had no problem until today when the message in the title appeared next to each track, with a little red cross.

  I already deleted database library as suggested by some of the forums, also disabled the media as a feature of Win 7, rebooted and then re-enabled it.  I also disconnected externally and restarted that as well, I'm also the same mistake with a cd in the cd drive as well.

  Can anyone help?

  Hello

  This error may occur for one of the following reasons:
  The file is currently in use. Close the file and then try again.

  You are not allowed to access the location where the file is stored.

  Follow these steps to grant all permissions in the folder where the files are stored:
  1. right click on the folder on the external drive and click Properties.
  2. in the Properties window, click on Security tab.
  3. now, click Edit , and then click Add.
  4. now, type everyone in the box and click OK.
  5. check the full control box.
  6. click on apply and then click OK.

  You can also try the mentioned below as follows:

  1. click on start.
  2. go in Control Panel.
  3. Select "SOUND".
  4. double-click on speakers.
  5. click on the tab advanced and then uncheck the enable audio enhancements.

  Kind regards
  Amal-Microsoft Support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows Media Player error "Windows Media Player cannot access the file. Is the file may be in use, you won't have access to the computer... »

  When you try to download an audio conference on Windows Media Player class, the following notification: Windows Media Player cannot access the file. The file may be in use, you won't have access to the computer on which the file is stored, or your proxy settings are may not be incorrect. I was able to download in the past but now cannot. Any suggestions?

  In WMP, find the tab "Tools", "upper task bar", Search tab options when pressed.

  In the new properties window, change the tabs, connections would determine internet

  speed adjustment... Change all.

• I disabled the toolbar > > Menu button (via a right click on a PC, Windows 7) and cannot access the toolbar to add items to the sail back in. Any ideas?

  I disabled the toolbar > > Menu button (via a right click on a PC, Windows 7) and cannot access the toolbar to add items to the sail back in. Any ideas?

  Don't see the menu bar not (File, Edit, View, history, Favorites, tools, help)?
  Turn on/off the menu bar is a new feature in version 3.6.
  (Linux and OSX see: what happened to the file, edit and view menus? )
  Windows Method 1. Press and hold the key and press the letters of the following in this exact order: V T M
  Windows method 2 Press and release the button. The Menu bar is displayed; then choose ~ ~ red: V ~ ~ iew > ~ ~ red: T ~ ~ oolbars and click on ~ ~ Red: M ~ ~ enu Bar.
  The menu bar should now be displayed permanently, unless you turn it off again using view > toolbars. Check = not displayed, NO check mark is not displayed.
  See: http://support.mozilla.com/en-US/kb/Menu+bar+is+missing

  Navigation, bar toolbar bookmarks and other toolbars under view > toolbars. By clicking on one of them will place a check mark (display) or remove the check mark (not shown).

  To display the status bar, view, and then click status bar to place a check mark (display) or remove the check mark (not shown).

  Mode full screen
  http://KB.mozillazine.org/netbooks#Full_screen

  See also:
  Back and front toolbar buttons or others are missing
  Customize controls, buttons, and Firefox toolbars

• When I receive e-mails with an attachment can not open, it says: Windows media player cannot access the file, Please HELP

  WHEN I RECEIVE AN EMAIL WITH AN ATTACHMENT I CAN'T OPEN IT. IT SAYS WINDOWS MEDIA PLAYER CANNOT ACCESS THE FILE.

  Help, please

  How this is related to Windows Update, John?

• I have the version 7.0.1 of firefox and cannot access the cookie settings, I get errors indicating cookies are disabled, but cannot find anywhere in the Privacy tab that allows me to manage cookies.

  I have windows XP - Pro and recently upgraded to Firefox 7.0.1 and OE I get errors from web sites on cookie settings. I can't access the cookie settings via the tab tools option and privacy, because there is no option of cookie except to erase or delete individual cookies. I could manage my cookies before but something has changed in this version of Firefox, and now it's playing a lot of features of my web site.

  See all the parameters of the story and the cookie to use:

  • Tools > Options > privacy > Firefox will be: "use the custom settings for history".
  • http://support.Mozilla.com/kb/cookies
  • https://support.Mozilla.com/kb/enabling+and+disabling+cookies

• Windows Search returns "cannot access the file ' res:...» »

  Lately, whenever I use Windows Search, then click on a file that was returned in the results box, I get a weird error message that begins: Windows Search.  Cannot access file ' res:... "and so on.  Sometimes it opens then the file I want; other times, it opens a file that has nothing to do with my research.

  In my situation, on two computers, I checked with Windows XP, this seems to happen when I click on an Adobe. PDF file in Windows search results. The exact message is:

  Unable to access file ' res://ieframe.dll/navcancl.htm# [path to file]-.pdf [file] "."

  The Windows Search Preview pane does not display the contents of the file, but the file opens successfully in Adobe Reader or Adobe Acrobat. It comes with a simple click on the file, not a double click.

• Cannot access the Router #2

  Here is a diagram of my home network.  This is what works.  If I have a device (phone or laptop) connected to the #2 router (wired or wireless), I can browse my network devices and browse the Internet without any problems.  My problem happens the other way.  For example, if I have a device (phone or laptop) connected to the #1 router (wired or wireless) I can see all network devices, with the exception of #2 router and all devices connected to it.

  Starting from a device connected to the Router 1 # I can ping LAN ports and Internet #1, #1 wireless bridge and Bridge #2 wireless router.  However, I can not ping the Internet port on the Router #2.  I guess it's a setting on Router #2 just don't have yet.   Here is a list of my equipment:

  Wireless routers are the two Linksys WRT 54 G

  Wireless bridges are the two Engenius ENS202

  Any ideas on why this is happening?

  

  Turn your router n ° 2 in a switch\repeater.

  Changes required for the installation of WRT610n:

  1. Change the SSID of the evocative wireless for the location. Ex: UpstairsWifi
  2. This must be done at the same time on the configuration screen, change the IP address of the router to 192.168.1.254 for you there is an IP address conflict with your main router, disable DHCP and save the settings
  3. Don't forget after that point that the internet port of the router is not to be used only the LAN ports
  4. If you need to reconfigure this router you would use it's new IP address in the browser "192.168.1.254".

  This means that your network IP addresses range starts with ' 192.168.1.. " If not the typical another range of IP addresses would begin by "192.168.0. * ' in which case the router's IP address must be changed to 192.168.0.254

• WRT1900AC: Cannot access the router remotely

  This can be a simple, but I'm scratching my head on it.

  I just took a 1900 for my personal use at home. I did a basic auto config (Nothing fancy, just Plain Jane).

  As part of the configuration process, I associated the router to a Smart Access account that is different from that assigned to the routers in my church.

  For some unknown reason, I can not access the router using the Smart app unless I am accessing Internet through the 1900. If I have Internet access through my Verizon FiOS router, the Smart application tells me that my wireless router is offline.

  I missed the 1900 and started from scratch using my office... again... combining the unit on the account. Once again, no luck.

  I have a session with my smartphone and tried again with my tablet. Still no luck.

  Just to make sure that there is no failure, I tried to access the routers of the Church... and has been able to do without any problem.

  Y at - it an option that I forget? I don't remember running into this situation when you configure the 6500 s and 6900 s.

  10,168 is also a private IP address.

  I recommend that you enter this address that you see on the WRT router in DMZ ISP modems. If there is a reservation on the ISP modem function, book it as well so it can't change it later. This will keep the DMZ address for the WRT router and you should be good here.

• Cannot access the audio settings

  Hey everybody. Today I plugged my headphones in and waited for chip connect disable audio clear more because it's hurting my ears with headphones... He didn't do it, I tried to turn off manually but I couldn't access the audio settings in the music app... He just wouldn't do anything when I clicked it, then he said this: https://www.dropbox.com/s/c7drv4nf6o0pydg/Screenshot_2015-09-22-13-34-25.png?dl=0 and when I go to settings, audio, audio settings, it still says the same thing... I need help, I restarted my phone like 5 times to no avail... And I checked the running applications, and there is nothing that would make this...

  Thanks in advance

  Hello raul, it seems that you have downloaded an app enchancing equalizer or sound that prevents you from using the audio settings by default. Please check the app and delete it and try again.

• Cannot access the bluetooth settings or find devices

  I can access the bluetooth software. but when I click on settings or find devices, nothing appears. also when I go to programs it does not appear on the list. I have the icon on my computer, but it does not. I just want to plug my mouse and my mobile phone, possibly if I can make it work. Please help ASAP

  Hello

  read these tutorials on how to set up bluetooth

  http://www.vista4beginners.com/how-to-setup-a-Bluetooth-connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-Bluetooth-enabled-device

  Here are solutions to some common problems with Bluetooth devices.

  You can also try a convenience store for diagnose and fix common problems with equipment and devices running.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-Bluetooth-enabled-devices

  If the above does not correct it contact the hardware manufacturer

• Satellite L755-129 and Win8.1 - cannot access the BIOS settings

  Hello

  I have a L755-129 satellite and I have the version of windows 8.1 update in my laptop. I want to open the bios of my computer and I can't do it?

  What is going on? Also I can't find in the windows recovery Panel. Key F2 and F12 does not work, when I press it, the laptop starts beeping beep and starts in windows.
  Can someone help me? I don't want windows 7 I like windows 8.1.

  Thank you for your help

  It's really good that you posted this question. So far on this forum many people ask the same questions, but all have been at the origin of new machines of Win8.
  Now we have the situation with the old machine Win7 but with Win8 preinstalled.

  Solution for other people needed to proceed to a complete stop and after doing this, it was possible to enter the BIOS settings. Check it please http://aps2.toshiba-tro.de/kb0/TSB2B03EY0002R01.htm

  This situation does not for me so here's a question for you:
  When you start your laptop, I guess you can see the Toshiba start screen. With F2 option is shown on the bottom of the screen?

• Product: HP Pavilion Notebook-PC G7, cannot access the bios settings/turn off the keys f1 - f12, please help!

  I got this laptop PC in 2012, it is a series of G7, I'm pretty sure. My problem is that when I turn the computer off and turn it back on, there is no option to open the menu of the bios (esc) or any option besides. Just a symble blue HP directly in the middle of the screen with a symbol of little loading below him. I pressed ESC, f1 - f10 and virtually all other keys to try to access it. What I really want to do is to disable most annoying f1 - f12 function keys.

  I'm no longer under warranty and my operating system is Windows 8.  There is also no error at all, just no response what that's right don't charge up to login password screen.

  Please help and contribution is appreciated.

  Hi 2livewire4,

  Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I see that you are looking to access the BIOS of your laptop Pavilion. You can't access BIOS in the same way on Windows 8, because you have a faction of a second to get the right timing because of the quick loading of Windows 8 feature. This third party link will show you how to access the UEFI that will lead to the BIOS. You can also do it from the Windows 8 login screen as this Microsoft link will show. Here is a document from HP support disable the function on some models Fn key combination +.

  Thank you

• Cannot access the background settings of screen (Vista HomePremium)

  In the customization settings, it seems not able to change my wallpaper settings.

  Only the following options are displayed:

  The window color and appearance
  Screen saver
  Sounds
  Mouse pointers
  Theme
  Display settings

  It's my own laptop, so I'm the admin. I remember having the option before, and I went today to see if I had the options for a rotating background and to my surprise, I can't check it again. (If I can't it's good, but I wish that my ability at least to change my options of paper painted back)

  I can rightclick an image to set as office, but that doesn't help if I can't change the settings.

  Try fix Riou:

  Restore missing Options Page to customize in Windows Vista
  http://www.Winhelponline.com/blog/restore-missing-options-to-personalize-page-in-Vista/