QUICKY ON T21 and pcmcia USB 2.0

Similar Questions

• Connection keyboard and mouse USB Wired stall

  Hello

  My computer repeatedly interrupts the connection to my Wired USB mouse and keyboard.  Usually around one every 30 seconds, the connection falls for 1 to 1.5 seconds, then comes back.  Meanwhile, the cursor hangs - I can't click anything, and I can't press any keys on the keyboard.  For example - when I type, I have my keyboard will stop working for a while, and no text will appear.  This is particularly problematic when I play games.

  I tried to reboot the computer, reset the SMC and the mouse and keyboard.  I also tried all USB entries on my mac (4 in total), and the problem persisted with each of them.  This leads me to believe that it is either a problem with all the USB inputs, or a software problem.

  I have an iMac 27 inches, mid-2011 with OS X El Capitan 10.11.6 (specifications: 3.4 GHz Intel Core i7 processor, 16 GB with 1333 MHz DDR3 memory and storage capacity of 2 TB).

  I use a wired USB (Logitech G402) mouse and keyboard USB Wired (Razer BlackWidow Stealth).  I have the latest version of Logitech Gaming Software and Razer Synapse installed for support.

  I would appreciate help.

  Check if there are updates available driver.

  To check if the problem is with the USB to your Mac controller, test with a different keyboard or mouse.

  To check the extensions conflicts, etc., try the startup mode.

  -----

  Restart in Safe Boot mode by holding down the SHIFT key at startup. Secure boot is quite slow because the operating system performs some cleanup and verification tasks, so give it time. Once you're completely connected, restart normally.

• Qosmio F50 - keyboard and mouse USB disconnects for 2-3 sec

  Hello

  Well use a keyboard and a USB mouse to play games on it

  Somehow my mouse is "Razer Lachesis keyboard is 'Razer Lycosa' and I just installed the latest drivers for them."

  The problem is that my keyboard disconnects sometimes for 2-3 sec then am playing, but the mouse sometimes move slowly and don t answer correctly for the same duration 2-3 sec. I've tried everything updated and I went on Google and I didn t find something that can help

  In any case use windows Vista 32 - bit with latest updates and I didn't change the original Vista provided with my Qosmio F50 t.

  I hope you can help

  Hello

  Have you noticed intensively the HARD disk activity when this happens?
  East - the HDD LED flashes when the mouse or keyboard do not respond?

• Excite AT10PE-A-105 - cannot install and use USB driver

  Hello

  I bought the AT10PE-a-105 and I never managed to install the driver for debug applicatoin android with eclipse.

  I use Microsoft 8.1 64 bit (last updated).
  I'm following the available tutrorial (RTFM).

  Even I'm a fan of the home user, I need to root and the USB driver works. I post a bad review on gsm arena.

  Someone was able to use the USB driver?
  [usb driver | http://support.toshiba.com/support/viewContentDetail?contentId=4001813]

  I lose 2 days trying to install the usb driver without success and I give up.

  Material may not be updated compared to the pilot then could developer team Toshiba could do a upgrade from usb?

  Concerning

  + The message was edited: link has been removed not allowed.

  Your excited AT10PE-a-105 was released in the European region and it seems to be the right Android WinUsb driver

  http://support.Toshiba.com/support/viewContentDetail?ContentId=4001725

  The driver has been released for the operating environment
  Windows XP SP3 or later (32-bit Version)
  Windows 7 SP1 or later (32-bit / 64-bit Version)

  8.1 Windows isn t taken in charge and I guess this is the main reason why you can not install the driver on your system.

• Difference between left and right usb ports 2015 15-inch model.

  I recently bought a 2015 15 inch macbook pro with 2.5 GHz processor and 512 GB hard drive. IV used for only one month and I notice a difference between the left and right usbs. The base of the left usb IE the metal connector pins seem to be lower compared to the usb on the right side. Usb port on the left also seems to be a bit looser than the right, but hardly noticeable. IV barely used the usb ports and would like to know if it's the same for the other macbook pro users with the same model.

  The game is a concern, and I would take the computer to Apple for review. After all, you are covered by the warranty.

  My current MBP is that a 13 inch 2012 has only USB ports on the left side. My previous was a pre-Unibody 15 inches and I have not noticed differences in fit / release between the right and left USB ports.

• Pavilion P7-1410: load and sleep USB

  I have a p7-1410 Pavilion. (A) no it automatically standby if on but not in use?

  (B) she "sleep and charge" USB ports?

  (C) if B is "Yes", where the ports?

  Mnay thanks!

  Hello

  Please try:

  There is a way to maintain the USB active ports during the eve.  Simply go into Device Manager, navigate down to Bus USB controllers.  On each element of the USB root hub, then right-click and choose Properties.  Click the power management tab, and uncheck allow the computer to turn off this device to save power.

  Source: http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-performance/USB-power-in-sleep-mode/c8ab8475-03A1-41F4-868f-e59b3ec7b2c8

  Kind regards.

• Measurement of angular position with encoder in quadrature and NI USB 6281

  Hello.I have an application developed with labVIEW 7.1 and 6014 OR for the measurement of angular position using encoder quadrature, where are used 3 sons - one of them connected to the source, second to the OID (0 or 1) and a third to digital ground. I can't use the same application or NI USB 6281.Now connections, I would like to know how I can create a similar application in labview 2009 and how to make the relevant connections for NI USB-6281, which is a mx NI DAQ device. Please suggest. Thank you.

  I have my loan application. I understand there are big difference using LabVIEW 2009 and NI USB card, compared to the previous version I was using THE LabVIEW 7.1 and a traditional daq. The difference, I should say that wellness is both in terms of simplification of code and the accuracy of the result. I was a little surprised, showing results. Thanks a lot to JB for your time and sharing those pieces of details.

  I can well after awhile my code in the forum. Hope this helps someone like me looking for a similar application.

• Digital and analog inputs simultaneously - NI USB-6009 and NI USB-6212 - ANSI C

  Hello

  I'm reading at all times and at the same time analog and digital inputs. Digital and analog samples must be sampled at the same clock and acquisition should be started (triggered?) at the same time (I don't want, after some time, analog reception more digital samples - the opposite is also true).

  I found an example (in C source code) "National Instruments\NI-DAQ\Examples\DAQmx ANSI C\Synchronization\Multi-Function\ContAI-Read dig Chan" and tried to run with two USB cards: NI USB-6009 and NI USB-6212. Unfortunately, the two results by mistake, as described below:

  DAQmx error: the requested value is not supported for this property value.
  Property: DAQmx_SampTimingType
  You asked: DAQmx_Val_SampClk
  You can select: DAQmx_Val_OnDemand

  Task name: _unnamedTask<1>

  State code:-200077
  End of the program, press the Enter key to exit

  -Is it possible sync analog and digital acquisition in the paintings?

  -If so, how?

  Thank you

  Hello tcbusatta,

  Two of these modules, USB = 6008 and USB-6212, support only timed software inputs and digital outputs.  This means that you cannot define material timing (like finished sampling or continuous) for these modules.  Digital lines can be retrieved or written once to each call DAQmx read.

  This means that you will not be able to get any type of synchronization tight between the analogue and digital channels.  You will need a Board such as the NI USB-6341 in order to synchronize the AI and DI closely.

• PCIe-7852R and OR USB-7856R OEM Calibration with Calibration Executive

  Can I calibrate PCIe-7852R and NI USB-7856R OEM with NI Calibration Executive?

  How?

  Our version of National Instruments Calibration Executive Software is 3.5 and it has no procedures to OEM PCIe-7852R and NI USB-7856R products.

  Hello

  There are several ways to calibrate your instruments.

  First of all, the help file for the calibration of R Series devices to the Calibration Executive can be found by navigating using the Executive of Calibration > calibration device > data acquisition (DAQ) devices > NI dynamic signal Acquisition > NI R series calibration procedure

  You can also follow the instructions in the following document.

  http://www.NI.com/PDF/manuals/372004d.PDF

  Finally, you can also calibrate your software for the R Series devices using the calibration installed with the drivers. You can get "calibrate the device 78xxr" and run the executable file to calibrate your devices.

  Thank you.

  Kind regards

  Nigel

• What is the difference between the NI USB-4431 and NI USB-4432?

  What is the difference between the NI USB-4431 and NI USB-4432?

  I know NI USB-4432, but I do not know NI USB-4431.

  Hello

  Sorry for my previous post don't bother her.

  The usb-4431:

  • 4 analog inputs
  • analog output of 24-bit DAC

  

  

  Kind regards

• Acer XC-605. I have a wireless usb device and a usb dongle. Can I replace my w wireless card

  Acer XC-605. I have a wireless usb device and a usb dongle. Can I replace my card without extra wire with usb3 Sockets. If so, should what material I go for? Front Sockets have been botched again and are now worse thn useless. Thank you.

  Thanks Asdfguy86. The map you suggested was not good because it was full of size, but, thanks to your liknk, so I knew what to ask and what seearching I just added "low profile."

  My search came up with this https://www.amazon.co.uk/gp/product/B008N3FPXS/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

  This has also been enlarged but came with an alternative mounting plate.

  There is a free space above so I was able to move my antenna wi - fi so far and release the slot for pci express to the new card usb3 so I was even able to keep my embedded wireless and bluetooth. What a result!

• My touchpad does not work and the usb mouse works

  After connecting with a USB key, my touchpad does not work and the USB mouse works

  Hi, Dieudonné,

  Make and model of computer?

  Have you tried to uninstall the drivers for the touchpad.  Update?

• external hard drive and the USB does not

  When I connect my external hard drive or my USB which do not shown anymore.not or work

  Hello

  Check the configuration/settings (BIOS/CMOS) often F2 when you start - make sure that USB is enabled.

  If a PC and if necessary the embedded USB can be disabled and a USB card can be used only
  is not expensive. For a laptop, using a real computer shop (no leeks and glances at a Best Buy
  or other stores) or system manufacturer support.

  ------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
  Devices disabled - look around (with the exception of USB controllers) for your devices (can have
  zero or more than one) and top - right click UNINSTALL.

  Control Panel - right CLICK on EVERYTHING - Serial USB controllers - Device Manager and UNINSTALL
  all except the category itself - REBOOT - it refreshes the drive and battery USB

  This KB shows XP how to and the method of Vista is identical
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer, thus
  as all USB devices that you previously used. Run Options and check the 1st three choices to see to it there
  Is there.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• My sm bus controller and controller USB driver not there (read for detailed explanations)

  I have a laptop, it was windows 8.0 and I upgraded to 8.1, I didn't like it at all so I lowered it to win7 because it was laggy and the displayed text was fuzzy. I knew that something was wrong with the installation of windows 8 and even after a clean full format, he would not return to normal. I went and he downgraded because I had enough and know that windows 7 would be faster for this pc (which it was), I said yaay sound much smoother and faster with no problems.  Then I installed all the wifi, bluetooth drivers, mouse etc... only 2 things that I couldn't install was the bus controller SM and USB bus controller driver (USB). And my usb slots were not working other than port 3.0 I had a plugged usb of decommissioning...

  I know its something to do with the bios and since the update of the bios is 8 - 8.1 windows only I don't know what to do... I have a .wim file recovery and I don't know how to use it. I also forgot to put my product key of my pc of win8 before I went down I had no knowledge of what happen and don't think it would be a problem...  Now I can't connect more than 1 thing at a time. I went on the microsoft forums and they fixed a problem (ethernet driver) and told me to come here and I hope you can fix the rest.

  Thanks to adnvaced for your help

  The laptop is HP Pavilion Sleekbook 14-b006au
  Serial number: 5CD2490Y40
  Product number: C7D41PA

  Please can someone help me I really want to stay under windows 7 is it possible that someone could get an update of the bios manual for that laptop or something like that. Except that everything works fine!

  Here's a linnk to MS32 (computers)

  http://1drv.Ms/1u6Z6DP

  Hello:

  Here are links to the drivers you need.

  1 SMBus: Downloand unzip and manually install the driver for smbus controller I have attached under attachments below.

  Go to Device Manager and click the controller smbus needing drivers.  Click the driver tab.  Click on set to update driver.

  Select her browse my computer for driver software option and navigate to the driver folder that you unzipped.

  Make sure that the include subfolders is selected and the driver should install.  Then restart.

  2 USB3: Download and install both of these drivers and restart.

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_137148_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_133037_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• HP 14 Chromebook q000ed [after several powerwashes and a USB key recovery is crashed/restarted]

  HP 14 chromebook q000ed

  purchase date: November 2013

  - - -

  A couple of months chromebook began to crash/restart. At the beginning it was a few times / week, then it got worse to the point I had 2 powerwashes in one day and hangs / reboots even guest mode!

  After the restoration of the many powerwashes and a USB port, I got another problem of crash/restart. So the problem looks like it is material.

  I paid for this product and I can't even browse the internet. There are a few Q & a in support of google here.

  What advice you get?

  P.S. the recent crash/restart happened when writing this thread! Had to write this new!

  I'll give you the Dutch HP support site, where you should be able to locate the correct contact information: Neem contact op met HP

  You are classified as a student, because it is the system of classification of the Forums. It does not reflect that you are a student in real life.

  Mario