RAID. Invalid firmware.

Hi all.

I get the nex error when starting. Help, please.

I checked a few cases and all required them a replacement of RAID controller.

Open a TAC case and get it replaced.

-Kenny

Tags: Cisco DataCenter

Similar Questions

  • DAQ 6008 cannot be seen on a mac "says invalid firmware. any help on this

    I'm trying to get my macbook pro to see DAQ6008 of data acquisition, I get invalid firmware error any version OR-DAQmx version I use

    I managed to do the work.

  • Can write us "PowerCLI Script" to get the details of card RAID HP (Firmware & Driver)?

    Can write us "PowerCLI Script" to get the details of card RAID HP (Firmware & Driver)

    For example: native ESX command below shows desired output for me.

    But we needed equality PowerCLI ESX command below script

    # cat/proc/driver/cciss/cciss0

    cciss0: HP Smart Array P400i controller

    Board ID: 0x3235103c

    Firmware version: 7.22# cat/proc/driver/hpsa/hpsa0

    hpsa0: HP Smart Array P410i controller

    Board ID: 0x3245103c

    Firmware version: 5,70

    Driver version: HP HPSA driver (v 5.0.0 - 17vmw)

    The extracted following PowerCLI you will get server and type of controller, firmware version and the hpsa/Smart Storage Array controllers driver version based of:

    Get-VMhost | Sort | Select Name, Model,@{N='Controller Type'; E={(Get-VMHostHba -VMHost $_ | ? {$_.Model -imatch '.*(hpsa|smart).*'}).Model}},@{N='Controller Firmware'; E={($_.ExtensionData.Runtime.HealthSystemRuntime.SystemHealthInfo.NumericSensorInfo | ? {$_.Name -like '*hpsa*firmware*'}).Name}},@{N='hpsa Driver Version'; E={($_.ExtensionData.Runtime.HealthSystemRuntime.SystemHealthInfo.NumericSensorInfo | ? {$_.Name -like '*scsi-hpsa*'}).Name}} | Format-Table -Autosize
    

    The sample output:

    
    Name                     Model                Controller Type   Controller Firmware                           hpsa Driver Version----                     -----                ---------------   -------------------                           -------------------esxihost1022.local    ProLiant DL380 G6    Smart Array P410i    HP Smart Array Controller HPSA1 Firmware 6.40    Hewlett-Packard scsi-hpsa 5.0.0.60-1OEM.500.0.0.472560 2014-05-15 15:32:23.000esxihost1023.local    ProLiant DL380 G6    Smart Array P410i    HP Smart Array Controller HPSA1 Firmware 6.40    Hewlett-Packard scsi-hpsa 5.0.0.60-1OEM.500.0.0.472560 2014-05-15 15:32:23.000esxihost1024.local    ProLiant DL380 G6    Smart Array P410i    HP Smart Array Controller HPSA1 Firmware 6.40    Hewlett-Packard scsi-hpsa 5.0.0.60-1OEM.500.0.0.472560 2014-05-15 15:32:23.000esxihost1033.local    ProLiant DL360p Gen8    Smart Array P420i    HP Smart Array Controller HPSA1 Firmware 5.42    Hewlett-Packard scsi-hpsa 5.0.0.60-1OEM.500.0.0.472560 2014-05-15 15:32:23.000esxihost1034.local    ProLiant DL360p Gen8    Smart Array P420i    HP Smart Array Controller HPSA1 Firmware 5.42    Hewlett-Packard scsi-hpsa 5.0.0.60-1OEM.500.0.0.472560 2014-05-15 15:32:23.000esxihost1041.local    ProLiant DL380 G5    Smart Array P400    HP Smart Array Controller HPSA1 Firmware 7.24    VMware scsi-hpsa 5.0.0-17vmw.500.0.0.469512 2011-08-19 01:58:59.000esxihost1042.local    ProLiant DL380 G5    Smart Array P400    HP Smart Array Controller HPSA1 Firmware 7.24    VMware scsi-hpsa 5.0.0-17vmw.500.0.0.469512 2011-08-19 01:58:59.000esxihost1160.local    ProLiant BL460c Gen8    Smart Array P220i    HP Smart Array Controller HPSA1 Firmware 5.22    Hewlett-Packard scsi-hpsa 5.0.0-40OEM.500.0.0.472560 2012-08-24 21:04:51.000esxihost1161.local    ProLiant BL460c Gen8    Smart Array P220i    HP Smart Array Controller HPSA1 Firmware 5.22    Hewlett-Packard scsi-hpsa 5.0.0-40OEM.500.0.0.472560 2012-08-24 21:04:51.000
    
  • 4 TB drives are hard ok for the XRAID2 Firmware?

    Hello.

    I have a 6 drive bay Readynas with X - raid 2 firmware and I wonder if I can fill it with 4 TB hard drives?

    Thank you.

    PS Ce that the devil is coming on this forum. Where is the blue on the page? Why does it seem all werid?

    Yes. Do a factory reset, you will be able to make full use of the space on the disks.

  • z820: looking for a software raid manage and view the status of disks hard raid

    HP z820 workstation,

    product # D3J63UT

    I'm looking for raid management software

    Thank you.

    I suggest that you follow the steps listed in the HP Document: "Z - series Workstation detection and fixing a hard drive failure within the RAID Controller utility" in the URL: http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c04474148#N10829 you can find instructions how to enter each State type of RAID (Intel RST, 2308 LSI and LSI 9260-8i controller - It's the main RAID controllers usually associated with the HP Z820 workstation according to the particular configuration you ordered). Note that in most of the cases described in this document, you need to access the configuration of RAID controller during computer startup steps, by pressing CTRL + I (for Intel RST) or CTRL + C (for LSI 2308) or CTRL + H (by LSI 9260-8i). The installation program uses the RAID controller firmware and does not require to install complex inside Windows software, because it is done outside of the Windows operating system before starting. Find more details in "HP Z220 SFF, CMT Z220, Z420, Z620 and Z820 workstations maintenance and Service Guide" in the URL: http://h20628.www2.hp.com/km-ext/kmcsdirect/emr_na-c04205252-1.pdf , in the devices of annex b: Setup RAID (pp. 161-171) all types of RAID controllers that are relevant at the workplace Z820 are discussed.

  • Reference DELL Modular Disk Storage Manager cannot see MD36xxf because of the version of the firmware to high

    I have a DELL MD3600f that is connected to a DELL R710. The system was all the installation and work programme, but the OS disk has become corrupted and had to be rebuilt. The system has not all backups, because it was still under construction. The problem is that a system administrator updated the Firmware on the MD3600f to the 07.80.41.60 version. According to the notes the versoin of DELL PowerVault MD Series Storage Software Resource DVD 3.0.0.18 or later must be installed before update the RAID controller firmware.

    Problem is the update of the firmware is already in place and the MD storage software cannot talk to the MD3600f now because of the correspondence of Miss firmware.

    No matter how lucky it is a updated software storage MD there? I tried low grade firmware, but that has been denied.

    Why not give the link to the latest version; 4.1.0.88?

    This is available at en.community.dell.com/.../4234.dell-powervault-md-downloads.aspx.

  • POWEREDGE 2900 - Perdita configurazione RAID [GRO]

    DELL POWEREDGE 2900 server

    Service etiquette: 82ZCL2J

    Buonasera

    Ho avuto no problem with there server sopra remainder. Non viene più caricato launch Windows. Dopo essere nella configurazione del raid entered, ho visto che non era più any configurazione impostata! (He raid age settato l 1).

    I have brain comunque non hanno personally I dati. Otherwise riconfigurare wanting it raid e vedere is it server riparte.

    Pero mi'd sapere come e stato possibile? It could be he controller guasto? Ed inoltre non having the che non possa ricapitare e possibile auswechseln tell it controller?

    Grazie

    Saluti

    Salve,

    Poter riconfigurare is he raid controller e tutto miss it to content. He reason by cui configurazione TR e persa could not dipendere dalla raid controller, banalmente a riavvio aspettato no la has uno sbalzo di corrente Può generare problemi di questo tipo caso in some.

    There's sono presenti sul nostro sito, especially sulla brain/raid controller firmware news.

    Saluti

  • I can't spend S370 because RAID Firrmware update is necessary, but this is not for my RAID card

    Hi guys.

    When I have never upgraded my Ironport Web Security Appliance for AsyncOS 7.7.0 S370 build 761 upgrade, for example, he said thar RAID Firmware update is needed for this, but if I try to update the firmware, the system told me that this is not for my RAID card

    What can I do?

    It is the result of the cli for upgrades:

    "

    SFPPRXY1P.intranet.Cajastur.es > upgrade

    .....

    Updates available.
    1 AsyncOS 7.7.0 build 753 upgrade for the Web, 2014-07-07
    2 AsyncOS 7.7.0 build 757 upgrade for the Web, 2014-07-28
    3 AsyncOS 7.7.0 build 761 upgrade for the Web, 2014-10-01
    4 AsyncOS 8.0.6 upgrade version 119 for the Web, 2014-10-27, is a version available for general deployment
    5. update the RAID controller firmware (for S360/S370/S660/S670 only required restart)
    [5]> 5

    Perform an upgrade may require a reboot of the system after the upgrade. You can connect again after that. Do
    you want to upgrade? [Y]> Y

    Not applicable to your RAID card upgrade
    Facility upgrade is complete.

    SFPPRXY1P.intranet.Cajastur.es > upgrade

    .......

    Updates available.
    1 AsyncOS 7.7.0 build 753 upgrade for the Web, 2014-07-07
    2 AsyncOS 7.7.0 build 757 upgrade for the Web, 2014-07-28
    3 AsyncOS 7.7.0 build 761 upgrade for the Web, 2014-10-01
    4 AsyncOS 8.0.6 upgrade version 119 for the Web, 2014-10-27, is a version available for general deployment
    5. update the RAID controller firmware (for S360/S370/S660/S670 only required restart)
    [5]> 4

    Perform an upgrade may require a reboot of the system after the upgrade. You can connect again after that. Do
    you want to upgrade? [Y]> Y

    Stale lockfile deletion

    Note: A new firmware is required for your RAID controller before you can upgrade to the version selected AsyncOS. This update should be canceled. First please update the firmware by running a new update and selecting "update the RAID controller firmware (for S360/S370/S660/S670 only required restart).

    Please see the release notes on http://www.cisco.com/en/US/products/ps10164/prod_release_notes_list.html for more details on the update of the firmware.

    The upgrade of the system has failed. This could be the result of a network interruption or a bigger mistake.  If the problem persists,
    Please contact customer support.

    SFPPRXY1P.intranet.Cajastur.es >

    "

    Thank you

    Regarding issue 1: it could be this new firmware is already installed.

    Look at page 3 of the release notes (http://www.cisco.com/c/dam/en/us/td/docs/security/content_security/RAID _...)

    After running the update of the firmware, the firmware upgrade package appears in the list of available upgrades even after a successful installation. The presence of this package does not indicate a failure of the upgrade.
     
    8
    To verify that the upgrade is running correctly, you can run the upgrade script again after the machine has restarted. If the upgrade was successful, the upgrade script indicates that the device does not require the upgrade
     
    Regarding your second question: the software upgrade:
    -you have an internet connection for update servers (the upstream proxy settings check maybe..)
    -What is your version of the software running (did you check upgrade)? Maybe you should first upgrade to 753 or some other version...
    -Maybe the reboot will solve the problem?
     
  • RAID 1 array degraded; no option to rebuild

    I have a PowerEdge T110 server with a PERC S100 RAID controller (firmware / RAID of 'false').  Unfortunately, I had a little accident tonight while I was working on this machine.  In trying to clean up a mess of cable, I accidentally yanked on the wrong cable and disconnected the power supply of the server.

    When the server has been run through POST, he paused and said the RAID 1 array was degraded.  Entering the S100 configuration, it tells me that unit 0 is degraded, and the other is fine.  The server starts very well.

    I opened the OpenManage utility that displays the status of the Ramdisk to deteriorate as well.  However, despite the poster the State as being degraded, absolutely nowhere no it lists all option to rebuild the table.  I can't even check the consistency.  Under the drop-down list for 'tasks', the only available options are:

    1. Delete
    2. Having-right/remove the dedicated hot spare assignment
    3. Change of name

    That's all.  Of course, I don't want to do any of these.  The BIOS configuration utility seems also unnecessary.  Although it lists the specific physical drive that is deteriorating, I see no option to rebuild the coherence of the table.  Because the physical disk has failed and is not actually damaged, I don't need or want to replace it.

    So, why everything isn't rebuild option listed, and how can I rebuild this table without deleting all of the volume and restore a backup?

    I tried swapping cables, and while he was smart enough to realize that the disk has just moved, it has not affected the degraded disk.

    I decided to do bankruptcy and just remove the degraded and 'clean' drive by using DiskPart.  That has worked, and Windows 7 shows the drive as "not initialized".  I put back it in the server, and it has been recorded as being non RAID... was not even as 'new '.  Basically, it was like its own volume automatically.

    I kept starting in Windows Server to verify that I have screwed something up to put my nerves at ease.  Windows starts, I went in the virtual disks of OpenManage section and saw that the (rather old) 'new' drive appeared.  So, I chose "delete" in the list of available jobs.  He deleted successfully, disappearing from the list of virtual disks.

    At this point, I thought I could go ahead and assign a spare drive dedicated to the array degraded since the tasks available.  Nope. No disks available. What?

    Panic now, I went in the "physical disk" section of OpenManage, and he was there with his status as a 'ready' (opposite to 'online').  The title of his available tasks, it was 'global hot spare assignment. "  I did that, and the status of the RAID battery under 'virtual disks' changed to 'reconstruction '.

    [ADMIN NOTE: profanity removed by TOU], why was it so difficult?

    During the time I spent writing this, its reconstruction progress has reached 4%.  I'll update on the State when it is finished.

    EDIT: Everything worked successfully.  Reconstruction finished after a few hours and the RAID volume is re-reading in good health.

  • Data store is not mounted automatically after updating the Firmware of the LSI

    I've recently updated the card RAID LSI firmware on my ESXi 5.5 system (patched and update top of page)

    When I rebooted, took place the following:

    1. the associated VMFS volume RAID was mounted

    2. the data on the volume store was not mounted

    I mounted the data store manually and restarted my VMs

    Do I have to re-signing the Volume and/or the data store to raise it properly.

    Steve

    The command should be ok and do the same thing as the command esxcli esxcli storage vmfs snapshot mount -l label|-u uuid (for details, see http://kb.vmware.com/kb/1011387).

    André

  • Yet WT8-A-102 stops suddenly and updated the BIOS

    I bought a Toshiba still WT8-A-102 (not part no PDW09E-00100EEN) to the end of 2014. I upgraded from Windows 8 for Windows 10 Home Version 1511 without any problem in 2015.

    I use it for a limited number of applications - Office365 and navigation, generally with Chrome and Hola VPN to access certain geographically limited websites, for example TV channels, watch movies and content recorded from my TV (these are generally. TSV format); I run the free version of Malwarebytes and AVG anti-virus.

    I have two problems I can solve t.

    1 stop abrupt

    For a few months now, it always turns off suddenly, always exactly 30 minutes after the start. There is no warning, the screen goes black and that s it. You can immediately restart and continue as before, but the same thing will happen again after another 30 minutes. It happens that it s plugged in or on battery power.

    I can find no reason for this. For example:

    • It didn't happen when I've upgraded to Windows 10 but a few months later.
    • The battery does not turn down.
    • The Tablet does not heat.
    • It occurs regardless of whether you ve been using the Tablet constantly for 30 minutes or simply turn it on and let it idle.
    • Sleep and stop times are set to one hour.

    I ve looked at event viewer and the only things there are a few system errors showing which means nothing to me (a server is not registered within the required). Certainly, there is nothing that happens in the few minutes before it turns off suggesting a reason.

    Any ideas please?

    Update 2 BIOS

    I ve installed the different Toshiba updates available for this model. However, the update BIOS doesn t work. She is currently the version 1.60. I ve downloaded the version 1.80 for this model on the desktop. The zip file is bios-20150722112320. I extract it and it starts the process. The Tablet goes on to say it's reboot and then a panel will appear that says:

    InsydeH20 Flash secure
    Invalid firmware image!
    Press any key to reset the system

    It s a Tablet! While they want me to? I ve you press buttons - Windows and volume - but nothing happens. If I just leave it, it turns off after 30 minutes and we re back with BIOS version 1.60 and I can work as usual.

    Although this seems excessive, but suggestions please?

    Thanks a lot for any advice,
    John

    It seems that your problem is similar to mine. I'm having the same random stop downs https://forum.toshiba.eu/showthread...-Error-Code-10 also I have an error code 10 in Device Manager. The agenda called "Intel Trusted execution engine Interface"... are you facing the same error?

    I sent my tablet at the service of Toshiba, it has been over a month now and still waiting to be informed about the problem!

  • RD630 BMC BIOS update failure v16

    What didn't was not doing the update BACK to v16 v2.10 BMC, it omits to say Phase 2: timeout.

    I'm assuming that Phase 2 is the creation of the virtual USB?

    If I'm wrong please let me know.

    3. copy the BMCDOS folder previously extracted on the bootable USB of MS-DOS key.
    4. boot on the USB key on the server that requires the BMC update.
    5. run efbmc.bat to start the update BMC create a virtual USB device.

    Never went to this place. Said the Phase 2 Timeout

    6. when the application system create virtual USB device successfully and reboot the system by Ctrl + Alt + Delete.
    7. press F12 to select the USB device as the boot device to enter in BACK and enter the folder BMCDOS Bpackage.
    8 run new efbmc.bat to start the BMC update and fill it.

    Does anyone have a suggestion?

    I've already updated the system BIOS to the latest version as well as the card RAID LSI firmware.

    Thank you

    Karl

    Here are the steps I should take to get the BMC update to work.

    Completely turned off and pull power cards.
    Let stand for 10 min.
    Plug the USB bootable
    Connect the cords.
    Turn on the server.
    Press F12 to load the boot options.
    Select the USB bootable as startup option
    When the c: prompt type cd BMCDOS and press on enter
    Type efbmc and press enter
    Look AT the screen
    He doesn't go to the top, as the instructions say. The screen will repeat itself in fact twice.
    The only difference is that you will see 2 sections where it tells you if it is boot a start or two and then instructions.
    Press CTRL + ALT + DEL - restart the server
    Press F12 to load the boot options.
    Select the USB bootable as startup option
    When the c: prompt type cd BMCDOS and press on enter
    Type efbmc and press enter

    Here he now will tell you that he finds the virtual USB STICK and start download BMC updated firmware.
    This operation will last about 10 minutes, go through all of its updates and controls.
    When it's done, it will be back to the command line.

    Hope this helps others.

  • 240 GB Extreme update problems

    Hello

    I took delivery of an Extereme 240 GB and have tried to update the latest firmware. I downloaded the update from the web site (v1.0.0.1) and detects the disk showing a version of the firmware installed of R201. However, when I try and update the firmware using the option "Check for Updates" it returns the error:

    Found invalid firmware update.

    I tried to re - download the update, but get the same error.

    Can someone please help? I don't think that I did nothing wrond, but a forum search does not show anyone else seeing this error.

    Kind regards

    Dave

    Well maybe you should try it with this one, which is the version lates and Sandrine.

    http://KB.SanDisk.com/app/answers/detail/A_ID/10476/kW/SSD%20Extreme%20Firmware%20update

    Make sure you download the corect so firmware for you the 240 GB version!

  • Reference Dell R710, Dell and VMware VAAI MD3200

    Hi guys, we have 3 x Dell R710 hosts running VMware ESXi hypervisor v5.1. Our SAN is via Dell MD3200 Direct attached storage. We have activated the option of High Performance. My question is about VMware VAAI. In particular, the recommendation of VMware: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1033665 it says: "For more information on support VAAI in a particular storage group or required firmware levels, contact the storage array provider." So I'm wondering: is VAAI supported (or not) with the MD3200... and otherwise: should I be deactivation of VAAI settings as recommended by VMware? What are the potential implications for the performance of deactivation of VAAI... or support DO NOT turn it off? Thank you, Steve

    Indeed, you are using a fairly old firmware. The most recent is 07.84.53.60.

    To be able to upgrade to this version, you will need a version quite familiar of the MDSM. I would say to download 4.1.2.29 or later, which is 5.0.0.70. All servers Windows and Linux (not VMware or XenServer) server that manage and/or are connected via iSCSI SAN should have their MDSM, updated software before upgrade you the firmware on the raid on the SAN controller.

    RAID controller firmware: www.dell.com/.../powervault-md3200

    Latest resources DVD (5.0.0.70): www.dell.com/.../powervault-md3200

  • ESXi & Installer hangs when starting

    Hello

    I looked around and looked for my problem-related entries in the forum, but I couldn't find anything...

    Here is my problem:

    * New server Fujitsu TX200 S7:

    2 x Xeon CPU / 64GByte = 16GByte RAM 4 x / 4 x SAS HDD 600GByte / RAID LSI Ctr RAID0/1/5/6/10/50/60 mit FBU - Erw. + Modul TFM / DVD - RW / embeddet USB Device of the UFM

    I experienced enormous problems to start with the installer of vmware esxi 5.1 (or 5.0) CD ROM or esxi host 5.1.

    What works with the above server:

    * Install it is an os windows 2012 std server on the raid system is executed without absolutely no problems

    Start the success of server std 2012 win every time.

    * Setup a esxi host 5.1 on the server, but only subsequently install Fujitsu «server see DVD»

    What does NOT work with the above server: (every time, never had a successful boot)

    Booting with the esxi 5.0 installation CD original fujitsu - fails!

    * Start with one (from vmware) downloaded fails - esxi 5.1 installation CD!

    * Start with one (from fujitsu) downloaded fails - esxi 5.1 installation CD!

    Start a successuflly by the Fujitsu 'Start Server CD' installed esxi host 5.1 on this server - fails!

    * Test: start without lsi sas controller (without any disk hard sas) - the server starts faster (without the lsi raid controller firmware)-, but fails.

    * Test: starting with half of the installed RAM - fails!

    The symptoms of what happens during startup and cannot:

    * First step of booting (bundle of progress on the top of the screen) will run successfully

    * During the first seconds of the second stage (starting ESXi Kernel, beam of progress is displayed on the bottom of the screen), the computer did a hard-reset and the startup process begins once more.

    So I don't know what I could do.

    Because all windows system works perfectly, I would exclude a hardware error

    On the other side, Fujitsu specifies this server with this equipment compatible with esxi, then I do not understand that no esxi (Installer) will be initialize to top.

    So, what could be the reason why the software does not start?

    How can I know the reason why the systems do not initialize-go to top?

    Thank you very much for any suspicion solve my problem!

    What about Tom

    the firmware all is patched up?

    There might be something that win2012 is ok with it the flaws esxi hypervisor

Maybe you are looking for

  • Text messages

    How can I create a group text message to with a photo attached?

  • Satellite A300 - Satellite icon and touchpad are not lighting

    Hello I have a toshiba Satellite A300. When turning the power on it this morning I noticed the 'Satellite' icon and the touchpad are not turn on as usual.Always work normally but I'm sure they used to be illuminated whenever the laptop was switched o

  • Why can't I configure guest network?

    TV, telephone and Internet are brought home through fiber TDS and distributed to households through ethernet. Actiontec modem/router (Model T 2200 H of TDS), is connected via LAN to my Airport Extreme (model HE ME918 / bought 08/09/15), and the prima

  • Error-1073807202 lack of Code Library in open VISA

    Hello I'm trying to contactANRITSU MS9710B via GPIB optical spectrum analyzer. Anritsu provides-Based VISAS screws for all functions. When you try to initialize theinstrument (using VISA Open), I get the following error:-1073807202, which is "a code

  • How can I validate my copy of Windows XP

    I am trying to create a copy of mssstool32 on a cd but it takes imapi v2. but it says that I have to validate my XP first.How can I validate it?