RAP with the wireless client

Similar Questions

• Satellite A660-13D - I can't go 65 Mbps with the wireless connection.

  + Sorry for my English is not my mother tongue. +

  Hello

  I expose my problem:

  I can't go to 65 Mbps with the wireless connection. I can't move this connection speed.

  Configuration of the laptop:

  * Windows 7 Ultimate 64-bit (with all updates installed).
  * All the updated drivers correctly.
  * With the latest version of the BIOS.

  Router:

  * Tp-link TL-WR1043ND, installed at 3 metres above the laptop (without obstacles).

  The router configuration:
  * WPA2-PSK AES.
  * 802.11n
  * Maximum output power.
  * Channel: 11 (not automatic, that this channel is relatively free).
  * Width of channel: 40 Mhz.
  * Maximum tx frequency: 300 Mbps.

  Other information:

  The wireless card drivers are correctly then updated (ver. 5.60.48.35).
  * The router has updated the firmware.
  * I tried all the settings of the wireless card.
  * Bluetooth off (without interference).
  * {color: #ff0000} there are other computers on the network that connects 150 and 300 Mbps (with the same network configuration). {color}

  Thanks in advance,
  Greetings.

  Post edited by: Xibalba

  Have you tested using different channels?
  Have you tested speed WIFI connected to another router?

• Problem with the wireless on the system tray icon.

  Original title: wireless

  not found wirreless icon in the taskbar

  Hi Amourhbone,

  Thanks for posting your question in the Microsoft Community forum.

  It seems that you have a problem with the icon on the system tray wireless.

  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.
  Provide us with a few details in order to better understand the issue.

  1. which version of the operating system are you using?

  2. deal with any problem with the wireless network using Internet?

  3. do you receive any error messages?

  4. did you of recent changes on the computer before this problem?

  I suggest you try the procedure described in the article and see if it helps.

  System icons do not appear in the notification area in Windows Vista or Windows 7, you must restart the computer
  http://support.Microsoft.com/kb/945011

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  Get back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.

• How to get Windows Live Mail 2011 to remove emails from my hotmail server account once they have been synchronized with the WML client. ?

  How to fix WLM 2011 to remove emails from my hotmail server account once they have been synchronized with the WML client. ? I've seen several references in forums to an option that is located on the Advanced tab in the menu Options/Email accounts/properties, but I don't have an option in the Advanced tab in this menu. Is there another way to do it. ? I tried to do this manually, but when I manually delete a message in my Hotmail account it also deletes the message on the client when it synchronizes. I would like to have my messages stored on my customer only and not on the server. Is there a way to do this. ?

  View all Windows Live and Hotmail questions in the appropriate forum found here:
  http://windowslivehelp.com/

• OfficeJet Pro 8500 a - problem with the wireless radio

  First of all, I'm sorry for my bad English. I hope that you have little imagination when reading. I'll start to describe the problem and the lower list, I hope, all the relevant information you need to help me.

  Yesterday, I bought a brand new OfficeJet Pro 8500 has.

  Since I have found a little bit of my computer and my router I configure for wireless connection.

  All whent fine, the printer connected to my WIFI network without any problem and I was able to do a scan using the HP scanning software. How ever, when you try to scan a document nother directly after the first that did not work. I got an error message on the computer telling me that the computer could not connect to the scanner and it could be caused by the firewall. I also tried to print a word document, but it seemed that the document could not be sent to the printer during the observation of the State of the printer. Finally I gave up the print job and began to study the problem.

  By using the service to help in the HP software that I did all the things he suggested me to do. I have disabled the firewall, open TCP/UDP ports, restarted the router, the computer and the printer in different combinations, nothing worked.

  All the while the printer was connected to my WLAN, indicated by the State of the network printer and the router. I was about to give up but thought I should try only to disable and enable the transceiver wireless in the printer. To my surprise this solves the problem. I was in a position of scan and print documents.

  Today, after work, I tried to do another analysis, and the same mistake was present. Once more I did magic with the wireless radio and it has temporarily solved the problem, but he came back a few minutes later.

  Summoriz, the error can always be corrected by disable and enable the radio wireless, but after some time (a few minutes) the error returns that it self.

  I played a bit and discovered that it is possible to access the built-in Web server during the error. Not all functionality of the EWS seems to work perhaps (it's OK) but I can't among many things has see the State of the network and I can even do an analysis using the integrated Web server.

  I tried to reconfigure the printer using the printer setup wireless and also after a reset of the printer and it does not help.

  I hope someone on this forum knows a solution to my problem.

  Useful information:

  Computer OS: Windows 7

  Router: Thomson TG784 (I have an internet connection, phone and TV provider and this box takes care of this)

  Encryption: WPA - PSK

  WLAN: 802. 11 b / g

  No filtering MAC or SSID hidden

  Other devices on the network are two mobile phones and a Motorola Xoom Tablet

  Printers, IP address: 192.168.1.81

  Firewall: WIndows (the router is disabled)

  Concerning

  Thord

  Problem solved. Reinstalled the PC s/w has little time and finally he solved the problem.

• 4320 proBook s - problems with the wireless Assistant

  Hello

  I have my ProBook s 4320 for about half a year now. For most of the year the half I had problems with the wireless assistant - it seems that when I start my laptop it takes about 5 to 10 minutes before the work of the internet. I never changed any settings in the wireless assistant.

  Nobody does face these same questions and no one knows how the internet starts immediately when I start my laptop? I tried this on different places with different wireless modems, but everywhere, it's the same thing and books of other people can use internet immediately.

  Thanks in advance

  Hello

  You are welcome to help

  The fact that it connects properly in Mode safe indicates that the driver who normally starts with Windows or a program is causing the problem - most likely candidate is to begin by F-Secure.

  Before attempting the following procedure, make sure that you have an installation of F-Secure program, so you can re - install this software, and also a license key necessary to activate it.

  Then, from the windows control panel. Open programs and features, click on the entry for F-Secure once to highlight, and then click the option to uninstall at the top of the window.  Once done, restart the laptop.

  Again, when windows restarts, check the internet connection by using only a known secure site.

  Let me know how this affects the problem.

  Kind regards

  DP - K

• I started having problems with the wireless mouse and the carpet of my laptop - Lenovo ThinkPad T420 mouse.

  Original title: right click on the mouse itself activating

  I borrowed a USB to a person at work and I started having problems with the wireless mouse and the carpet of my laptop - Lenovo ThinkPad T420 mouse. The left click of two devices works normally, however, sometimes she does not respond to clicks and it takes a few seconds to work. The left button was constantly starts to turn on, as if he was stuck. After that I hit Alt + Tab and modify windows it stops for a few moments and starts at a later date. I havo not found a specific condition or a combination of keys that may trigger the fault.

  I read a few posts on discussion forums, but all say that it could be a hardware problem, which I think is not, because both devices have the same problem and I'm sure it all started with the insertion of the borrowed memory stick. I scanned the readers to help Symantec's EndPoint Protection and installed Microsoft Security Essentials and performed a full scan, but found nothing. I even restored the system, but the problem remains.

  Should I get a different antivirus? How can I find the cause so I can find a better targeted solution?

  Try to install the drivers from this link and check.

  http://support.Lenovo.com/en_US/research/hints-or-tips/detail.page?&LegacyDocID=MIGR-77167

• Create a local user with the vSphere Client

  Hello

  I want to create a new user with the permission of readonly. In the vmware documation salon, they say I have to go to the tab local users and groups, but there is no tab with that name.

  And sorry for my English I'm not a native speaker.

  Hi and welcome to communities,

  This tab is visible only when you connect to the ESXi directly with the vSphere Client. You won't see when you connect to a vCenter server.

• Help, I changed the password of root ESXi via powerCli, now I can not connect with the web client or the console.

  Help, I've changed the root ESXi via powerCli password, now I can not connect with the web client or the console, but I can still connect to powerCli. The command I used was;

  SE connect-VIServer esxihostname-user root - password newpasswd

  This production network btw, I have connected to each host and run the above command, these ESXi hosts are not on a domain

  y at - it something I have left out. I really appreciate any assistance that you people can provide.

  Thank you, Joe

  It is probably a longshot, but a lot of things in the land of windows is not sensitive to capital letters as Unix is.  I wonder if your new password you put through powerCLI mixed uppercase in it and if the capitalization was abandoned by command windows powerCLI Analyzer, or he interpreted as all capitals or something.   If you can still get through the powerCLI you could try to reset the password again to something simple without capitalization mixed case and if your password on ESXi strategy requires a special character, try something different than a "$", like a "_" (I find that a '_' is less likely than some other special characters (, as a '-' or a ' / ' to cause problems with analyzers.).

  Edit:

  Another thing, you can try before playing with the password once again, is to create a different username ESXi using powerCLI and see if the password ends up what you think, it should be, and if you can get with the client vsphere using it.  In this way, you can find out if there are some problems with certain characters or Cap through command powerCLI Analyzer without losing your remaining root by powerCLI access.  After some tests, you can understand what went wrong with your initial password change and may be able to fix it with less risk of losing access.  I also assume that you can not create a new username on ESXi who is able to change the root password no matter what authority give you it, otherwise, you could create a new username with PowerCLI, then connect to the client vsphere with it and change the password to root from there.

• 5.5 beta sdk will be compatible with the web client 5.1?

  Hello

  We are studying options for vsphere web clinet plugin. We use the 5.1 sdk for our plugin currently. Now we continue to hear a lot of new features coming with 5.5 Sdk. So we intend to spend 5.5 sdk, visitors will also migrate to version 5.5 web client to use our plugin?

  Concerning

  Built with the SDK 5.1 plugins must be compatible with the Web Client 5.5.  Our goal is to ensure backward compatibility for at least 1 major release.

• Need help with the wireless internet Power Book G4

  Hi-I recently inherited a Power Book G4.  I have problems to connect to wireless internet.  According to the Profiler systems, it has an AirPort Extreme card, but there is no icon on the screen wireless.  Advice to connect would be appreciated!

  Thank you-

  Stephanie

  The icon in the menu bar can be hidden or displayed.  The setting is the system network preferences pane.  Where it says display, select AirPort.  There is a checkbox for the State of AirPort show the menu bar.  Since the AirPort icon in the menu bar, you can select the a local wireless network to join.

  This pane of system preferences, you can use the more specific configuration settings, although the default settings work often unless you use special parameters with your wireless router.

  AirPort Extreme Card maybe for 802.11b and gand not n.  If your wireless network is configured for 802.11n only, you will need to change this setting to allow to 802.11 g (on the wireless router).

• Photosmart more B209a_m: Virgin Super Hub does not connect with the wireless printer

  We recently upgraged to a new blank media 3 hub, the printer is connected to a Hp Windows Vista desktop via USB, other devices (laptops and tablets) could access the wireless printer when the computer is turned on.

  I also created the same printer to be used wireless by the other devices without the Office of marketing, it was a pain having to keep it logging on when he fell asleep. The printer had a different name if you are using one.

  After that the hub of the Virgin was installed I can is no longer using the printer without the Office being wireless, the new Center can not find the printer connects as is done before that other laptops, I had no problem with my old hub and a separate router.

  I've tried everything as suggested by Virgin (not much there) and reinstalled my drivers for the printer. Any suggestions what I can do?

  Hi @Confused_Nanna,

  Welcome to the HP Forums!

  I read your post about how you cannot connect your HP Photosmart b209 printer to your wireless network. I'm happy to discuss this issue for you!

  Please, try the steps in this guide, printer is offline (Windows) as well as this guide, the printer is not maintaining the wireless connection.

  If you are unable to reach a resolution, please click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

  I hope that this post helps!

• HP deskjet f4580: problems with the wireless

  Hi I have. Printing HP deskjet f4580 and I try to connect to my wifi but it doesn't I look on the hp page and I try to do by pressing the wps, but it did not help me pls thx

  PS I have an iPad without a computer mobile o

  Hello! @Liz1712, thank you for joining the HP Forums!

  I understand that you have your wireless printer connection problems.

  Please try a few steps recommended below.

  On the printer Panel, hold down the button for two seconds wireless.
  NOTE:
  The printer starts a timer that allows two minutes to push the button of the wireless router WPS.
  Hold down the button the router WPS wireless for several seconds. The printer automatically detects the wireless network and then configure the connection.
  If your printer connects successfully to the wireless network, proceed to the next step.
  If your printer is not connected to the network wireless with WPS, you must use a temporary USB connection to set up your printer on the wireless network. Go to the next step.

  Please refer to this article for more information: http://hp.care/2c5GfmP

  Let me know the results!

  Have a great weekend ahead!

• Do I need to use the software provided with the wireless hardware to go wireless? __

  I have a router Linksys Wireless (wrt160n) that I am not using. I whant to buy a (Linksys WUSB600N) for my office. I want to know if I need to use the software supplied with the hardware, or can I just use Microsoft Wizard to configure my network? Operating system is Vista Premium.

  Thank you Jeremy will do.

• I need help with the wireless system. One of my computers doesn't seem to get signal

  Hello, I installed Belkin F5D8235-4 router and im get the signal on one of my computers. On the other computer, it seems that im getting the signal, but it says unidentified network. When I try to open the internet it says is Interenet Explorer cannot display Web page. Do you think this could have to do with the card in my computer is not not compatible. I have an Atheros AR5007 802. 11 b / g WiFi adapt. IM thinking that if I buy a D-Link wireless G USB adapter, USB wireless adapter Compact of Linksys or a Belkin 54 G Wireless USB Adapter my computer may be able to get the signal. What can I do? Help please

  Hello

  Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
  Update your WiFi drivers on computers. How you are positioned in the router? Are there
  obstacles in the path? With the help of WPA/WPA2 security? You put on the G and N or N
  only? A to G for this adapter connect the send.

  Your Atheros should be consistent - could be drivers.

  Actually try updating your driver and disabling the network logon. (To do this, use a wired connection or)
  Download drivers on another machine and transfer on removable media).

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your router wireless and wired - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.