Re: Satellite U300 - 153 (PSU30E) - updated after the BIOS, I can't install Vista

Similar Questions

• Satellite A300 (PSAJ0E) - update after the BIOS, I can't start

  Hello

  I have an A30, and I tried a bios update to 4.2 which is the latest version for my model. BIOS update went well spent, that it prompted me to restart the laptop once the process is complete, but after this, I was not able to start. I made the screen where I can enter the BIOS Setup (that I can actually do and I am able to change the settings and save them) but after that the screen goes black and it crashes.

  At first, I thought I did something wrong and upgrade does not work well, then I started looking for the bios crisis recovery methods, I found this article:
  http://CRD.Y1.cc/
  After the steps, I managed to get my USB floppy drive works and, hopefully, flashing the BIOS, but it didn't help it would always hang at the same stage.

  My laptop has a warranty expired, so I can't fix it for free, and the service will probably cost me half of its price. Is there anything else I can do to get it fixed?

  I thought to Flash an older version of bios - perhaps the last 4.2 is not really compatible with my model, but I couldn't find everything... is it possible to get an older version of bios and give it a try with a floppy drive?

  Thank you
  Anton

  *@DCRM*
  You have a laptop A300D. It s a series different and, therefore, you couldn't t use the BIOS files designed for A300 series!
  This may damage the module ROM and mobo!
  You can find the latest version of the BIOS on the Toshiba European page of the driver... otherwise, you will need to contact the ASP in your country for assistance, or an older version of BIOS.

• Re: Satellite Pro A200 - black screen after the BIOS screen

  Hello
  I'm new to the forum and have a big problem. So, any help is welcome and appreciated.

  My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor. Also just as the screen goes black a beep can be heard which shows windows boot.
  I can access the toshiba Setup screen but not the installation of security mode.

  Kind regards

  Hello

  You wrote that you can access the BIOS, but have you checked if the HARD drive is recognized properly? Perhaps because the computer cannot start HDD isn't recognized then you should check this.

  If the HARD drive is recognized, I would try a Toshiba Recovery disk recovery facility. It seems that Windows isn't able to start and if you reinstall the whole system should help get rid me of this. Go to the start menu and select the CD/DVD drive as a boot device.

  Check this box!

• Satellite L300-1 has 3 - after the BIOS update, I get a BSOD

  I have a Satellite L300 1A 3 MODEL PSLB8E. I decided to update the version of the BIOS, thinking that he can resolve my issue of ethernet controller.

  But after the update, my laptop goes on infinite blue screen of death. How can I recover from this injury?

  Can someone please help.

  Hello

  Did you choose the good BIOS update for your model? Was it for Satellite L300 PSLB8E?

  What code you get BSOD?

  After the BIOS update you must always load the default settings. Maybe a bad BIOS setting is causing this BSOD.

• Satellite U300-153: how to use the resolution to 720 p on TV

  I have laptop satellite u300-153 and a HD ready LCD Tv.
  I have the connected with vga cable, because the laptop has vga output.

  The problem is that when I change the output resolution in the Setup menu of the graphics card to a larger than 1024 x 768 resolution, television reports an error of non-signal.

  I searched this forum and found that it's because the resolutions on the one I mentioned earlier are locked in Bios of the Government.
  I would use a normal on my HDTV 720 p resolution, because I intend to use it as my main screen at home.

  Using the 720 p resolution is not required, I would be just as satisfied if I could use any other wide screen resolutions.

  Hmm. I think that the problem is you graphics driver doesn't support external resolution of 720 p (1280 x 720).

  Unfortunately, if this resolution is not included in the graphics driver, then you will not be able to use it :(

  That's pity

• Satellite Pro L300 - which improved after the BIOS update

  Hello users,.

  I just finished an update of the BIOS on Satellite Pro L300 using Updater Insyde Bios. I tried the Toshiba site to see what's new or what has improved since the update my bios 1.7version v2.2. But there is no search results. I also went to the site Web Insyde, but neither have they put up what has changed or improved?

  Is there a documentation or information which could help me to know how my laptop has improved or better after the update of the BIOS and what has changed since my update of the BIOS?

  Thank you

  Hello

  I assume you mean a changelog of the BIOS. Well, normally this document is placed on the Toshiba page where you can download the BIOS update.

  If you can't find such a t changelog, there is no available changelog. All that s!

  In addition the BIOS update should be performed only if it of really necessary. This means that if everything works fine, I don't see a reason to update because this update is a bit risky.

• Satellite U300 - 14K (PSU30E) - what is the WLAN and other materials?

  What is the HW wlan in the machine? Machine pre-installed Vista (32 bit). The data sheet does not specify the HW very well.

  Device Manager says PRO/wireless 3945ABG Golan [HEIGHTS], but the download wlan driver has no driver for it. Ago realtec drivers atheros and intel, but the page intel does not list U300. Toshiba wlan page has the driver.

  There was also a network interface "isatap" (pilot: tunnel.sys).
  What is c? It did not work.

  How about the battery Bluetooth?
  The more pages of Bluetooth (http://aps2.toshiba-tro.de/bluetooth/index.php?page=download) has some drivers. Is the new one (6.40.02) the right one?

  It also has Phoenix Trusted Core BIOS. Is it possible to go further in the BIOS settings, such as enabling/disabling HW?
  Now it is mainly the password and setting of start command interface.

  Hello

  You are right. Wireless laptop card is 3945ABG Intel Intel (Golan Heights) and the driver can be downloaded from http://aps2.toshiba-tro.de/wlan/?page=downloads
  I can see version 12.2.0.11.3 is available for download.
  Driver free download driver for Vista and with exe files extract it to a folder. Look later check this file and go to the Vista32Drv folder.

  Drivers are there and install them manually with WLAN Properties > install new drivers.
  This method works?

  So what about BT? The latest version is the most recent and you can install it on your laptop satellite.

  What you want to do with the BIOS settings exactly? some certain hardware components can also be disabled in Device Manager.

• Satellite A100 does not start after the BIOS update

  Hello

  I downloaded the update to the bios toshiba A100 PSAA8 on the toshiba site and applied using the procedure of updating the bios from windows XP MSE. Restart after the start of the update stopped at the toshiba start screen.

  At startup the screen by pressing ESC watch text mode. The message indicated it confirms the update of the bios version. POST messages are:

  _________________________
  Genuine Intel CPU
  No TPM or TPM has problem
  1015 M system RAM passed

  Press to enter in SETUP
  _________________________

  Pressing F2 just clears the last message in line and then no change is found.

  The laptop comes with windows XP media center edition. I don't know why the TPM secure is enabled. It is possible that toshiba is available with the module of TPM enabled in bios updates that logbook. If this is the case, they must clearly identified as 'not applicable' upgrade for machines that are not relevant.

  I found similar messages around the forum without convincing answer.

  Is it possible to fix this without sending? Even if it turns out to be affordable, it make much sense to pay for the problems caused by toshiba.

  Hello

  Please don t blame someone for you mistakes ;)
  As far as I know that only a few sets of laptops come with TPM.
  If you want to do an update of the BIOS on the models at TPM, you will need to contact the ASP!

  Looks like you used a bad BIOS or bad BIOS update procedure.

  The Toshiba page a BISO update the documentation that describes how to upgrade the BIOS on each series laptop!
  You will find on the page of the Toshiba driver compatible BIOS and information over a large number of details!

  > Is it possible to fix this without sending
  Don t think so, and therefore, you will need to contact the Asp help!

  Good luck

• Satellite A660 - 11 M - update of the BIOS (Winflash) crashes every time

  Hi all
  I bought an A660 - 11 M a few months ago and thought I would update the BIOS to stop nagging Tempro and see if she helped no insidious problem, I tried to correct. I downloaded the zip, extracted and ran the .exe according to the instructions on the help site. WinFlash opens, runs the first step (new load bios) but hangs on step 2 (analyze the compatibility of old and new bios). Then a message "Winflash.exe has stopped working" Windows appears.
  This happens whenever I have try, even with shut down antivirus and directly after startup with no other programs running.
  Any ideas?

  I am running Windows 7 Home Premium 64 bit, I "dualbooted" Ubuntu using wubi, but the update to the bios was not until I installed IT... Perhaps it would work better in wine? ;)
  Any help is greatly appreciated!

  To be honest the best option for you is to remove Tempro system and be happy.
  In General, if the laptop works well, you need not update BIOS.

  If you see it doesn't work properly with her don t risk. If something's not going to screw you up BIOS and kill the machine.

  In any case, let's see if someone else with the same notebook has updated the BIOS successfully.

• Satellite Pro A300D (PSAK1E) - update of the BIOS didn't

  Hello

  I recently tried an update of the bios after doing a clean install of windows 7 64-bit. The process is complete and the phone has rebooted. In the end, the laptop could not start and just displays a black screen.

  I tried some of the methods on the internet using recovery from the crisis on a usb key, but have had no success

  I'm not so im using the wrong combination of Fn + B etc or what but could really do with some tips

  Thanks in advance

  Hello

  I put t think there is much you can do if the BIOS update failure. Usually in this case the ROM module needs to be reflashed, but this is possible only from an authorized service provider.

  In my opinion, you should contact the guy and ask for help. I m sure they can help you solve this problem. :)

• Satellite L350 - does not start after the BIOS update

  Hello

  I recently (yesterday) downloaded the latest version of bios update dated dated 25/02/10 2: 20 - WIN, after download and does run the software from the laptop immediately stopped working and stop. I am now no longer able to boot up the laptop at all, all I get is the power light on and the hard disk light flashes, I hear the spinning CD/DVD drive, but what is not screen anything, I don't think this is the start.

  Is there a way to fix this without taking it to a store/engineer, BIOS recovery?

  The laptop is a Satellite L350, I opened the laptop to try to reset the CMOS by removing the card mother battery (not sure if it would have helped), but as much as I know it doesn't have an or I'm not.

  Any help would be greatly appreciated.

  Thank you

  Andy

  Hi Andy,.

  Hmm... If the BIOS update failed, you can't do anything because only an authorized service provider has professional diagnostic and recovery tools to redo an update.

  So in my opinion, you must contact a service provider authorized in your country. Get in touch with the guy and ask for help. They will tell you what to do now.

  Here is their list:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an ASP.

  Good luck! :)

• Re: Satellite A300-243 - updated after the BIOS, it did not work

  Dear members...

  Good day...

  I have a problem with Toshiba Satellite A300-243, I installed the Bios after you download from Toshiba Web site, and when it's over, he restarted the machine and did not work, just turned on.

  So if any body can help me to solve this problem, I'm happy.

  Thank you...

  Hello

  It looks like that the BIOS update has no...

  What can you do now?
  Yourself you can do nothing. The only change is the authorized service provider. Technicians can try to reflash the ROM module

  Sorry mate, but in this case you need professional help.

• Ports Satellite A135 - S2306 defective USB after the BIOS update.

  OK, I searched all over the internet and not found anyone else with this same problem, or anyone with a solution that worked for me.

  A few weeks ago, I had the common error of the BIOS reset itself and asking for a password at startup. I took my local Toshiba authorized repair center, and they have not taken care of him, no problem.

  Since the resume, however, all 4 of my USB ports have been going crazy. What happened in the following three steps (in order):
  -One of the ports does not work at all, won't provide any current or even recognize that nothing is connected.
  -The 3 remaining ports are now only recognized as USB 1.1 ports, not USB 2.0 as they were before.
  -Now, only a very small number of my devices is not at all, with three USB mouse and two unrecognized hard drives work (I get the error message "USB device not recognized" standard Windows when I connect them to one of the three ports).
  I am running Vista Home Basic (32 bit) with SP 2 and the new version of the BIOS is v1.60.

  Is this something people of repair caused when they have unlocked the BIOS and updated? Is this a problem with the new BIOS itself? Any help would be GREATLY appreciated! Let me know if I let him out any relevant information, I tried to be as complete as possible. Thank you!

  The old Duke

  Hello

  > What is the repair people caused when they have unlocked the BIOS and updated? Is this a problem with the new BIOS itself? Any help would be GREATLY appreciated! Let me know if I let him out any relevant information, I tried to be as complete as possible. Thank you!

  It is not easy to say. I think that would be best to ask guys why it happens or what they have done in the past.
  But have you set the default BIOS?
  Please do; access the BIOS (by pressing F2). Set it to default by pressing F9 (I guess) and save the changes. Restart the unit.
  Access the Device Manager, and then remove all hubs USB and commands from the list of devices. After that reboot the device again. Windows should recognize the devices deleted again.

• Satellite U300 unable to operate after the Vista upgrade installation

  A couple of days, I did a Windows Vista upgrade on my laptop Satellite U300 and since that time, my computer does not work. He tried to self-diagnose this himself, he told me to shut down the computer and restart. I do that and then the! 0xc0190036! 4099/69249 (Security-Licensing-SLC-Component-SKU-Home...) appears with a black background. I tried to launch the product recovery disc but computer wouldn't it.

  Can someone offer me some tips?

  Kind regards

  Barry

  Hello

  It's very strange
  How have you tried to install the operating system recovery disc?

  Boot you from the CD and have you followed the instructions on the screen?
  Or what is exactly happening?

  Usually, the recovery disk must format the whole HARD drive and the laptop to the factory settings.
  In addition, the Vista is already activated and it s not necessary to put keys series.

  I see in the error message something about safety licenses. I m not very well what this may be, but perhaps could be a problem with activation, who knows?  :|
  But as I said above, the Vista on the recovery disk is already enabled.

• Satellite L30 does not start after the BIOS update

  Hello

  I upgraded my BIOS Satellite L30 and now the laptop will not boot. When I turn on the fan starts and that's it. I think I have updated the book with the bad BIOS... The laptop is only 1 day old... Is it possible to reset the machine to the default BIOS.

  Help, please...

  Hi Scott,.

  Unfortunately there is no easy way for you to go to your BIOS to its previous level. You need to entrust your laptop to a Service approved partner who has the necessary equipment to Flash the BIOS to the previous level.

  Kind regards