Read all ports on 6529

Similar Questions

• Visa reading reads all bytes to the port

  I have a camera that I communicate via the Serial Port. I have a standard communications protocol. For a particular command, I know that the exact number of bytes expected in return. I send my order. I see the correct number and exepcted to bytes in the port. I then read the number of bytes in the port. However, the VISA read returns only the first two bytes.

  I contacted success with this camera and this Protocol for more than 130 commands unique and different. There are only about 6 orders in which the read visa does not read all the bytes in the port. Anyone know why that would happen?  I expect to see 6 bytes. I see 6 bytes. I have visa read the command with 6 bytes. The visa read returns only the first 2 bytes. It's very very frustrating. I can do this exact process even with a different command. I expect 45 bytes of this command. I see 45 bytes with this command and I read 45 bytes with this command.

  I don't think that it is device connected as I can converse with success with the same camera on the same computer with the same cable of connector using non-LabView. It seems to be a problem strictly related to labview and VISA read the order. If someone could help that would be greatly apprecicated.

  Thank you.

  What is the exact byte stream that await you in return with this command?

  Instead of opening VISA, use the configuration Serial Port VI.  In this way, you can override the default values.  It looks that your instrument using all the defaults VISA of speed in baud rate, start and stop bits, etc.  However, in the VISA software, there is a failure to use a termination character, and this character is 10 (0x0A).  If you use the configure Serial Port, you can tell the pilot VISA do not use the stop character.

• Write to digitall all ports (channels) with the decimal value

  Hello

  It is possible to write all digital channels with a value decimal for a device with 96 channels at the same time?

  I have a USB-6509 camera and I want to write each value of Pentecost bit 1 in the loop (for the first transfer I write 0,1,2,4,8,16, 32, 64 and 128) with the line "Dev3/port0 / line0:7", but if I want to write all ports at the same time, how to set the line and the "write.vi DAQmx?

  Thank you.

  You can configure the reading and writing in the ports of 8 bits with the 6509.  For example, you could write just 128 to "Dev3/port0.  If you want to write to all 12 ports, I recommend doing a task that is several channels on the 6509 module, each channel of the task being a port.  You can then use the channel Multiple, single sample of writing of your values.  Your values must be in a table of U8.

• In what one account all read emails disappear when I go on a different account than the back. Read all emails will appear is no longer in the Inbox or the trash.

  In what one account all read emails disappear when I go on a different account than the back. Read all emails will appear is no longer in the Inbox or the trash. Is there a setting that I don't see. Thanks Johnny1

  Try view (Alt - V) - son - everything.

• Equium P200 - DVD drive reads all discs

  My DVD player just started reading some disks and not others, as some records are not read all the time, you can put a disk in, click on the dvd drive and it will open the player and say insert a disc, the device manager says device working properly and up to date driver.

  Does anyone know what is the problem?

  How understanding your problem if you have written on some and other disks?
  Can you explain what it more detailed?

• Read all rows in a worksheet except the first

  I have a spreadsheet with titles and I want to read a different worksheet with headings and add this info in a simple spreadsheet, but I want to delete all the titles of the apreadsheet of second, third, fourth...
  Can someone tell me please how to do this?
  I thought maybe if I converted to the worksheet to the search string, and rrplace titles and then return for a spreadsheet of table 2d, this could work. The thing is that I don't know how to get back to a spreadsheet of table 2d of the string with a single vi or in the simplest way possible, without knowing the amount of lines in each apreadsheet.

  Hello

  Read the first line of the second file and discard data. THEN read the remaining lines...
  Or read all the lines and remove the first row of the table...

• How do I program labview to read all 8 compact fieldpoint modules?

  I am new to fieldpoint and I my set-up block diagram to read 8 strain gauges using a SG-140 module.  My basket is filled with strain gauge modules 8 SG-140, and I need to know how to fix my diagram to read all 8 modules of SG - 140.  So, I need a total of 64 strain gauge readings 8 modules of SG - 140.  Can I do this without really copying what I've already done 8 times more?  Is it possible to use a loop or something to read the 7 other modules?  I appreciate any help I can get.

  My opinion about not having to duplicate the table of index based on what your VI was showing at the time.  Once you have the VI implemented with multiple modules, then you will need to implement an array of unique Index stretched far enough to get all the channels of interest.  From a 2D array, you need to connect both the row index and column index for a single scalar element.  So first channel would be 0 and 1, then 0 and 4, canal next 0 and 7.  The next module would be 1 and 1, 1 and 4, 1 and 7.

• Read all LVM files in a folder and compile

  Hello

  I want to read all the LVM files in a folder as shown in Figure 1. In each file LVM, there is a row of data that are important, like on the picture 2. I want to extract only the rank of value in all the files this particular file LVM.

  Then I want to compile in 1 Excel or text file.

  Furthermore, I also want to name each line values in newly compile it files. The name will be the name of the file extracted it previously, as well as the date and the time it was created.

  I tried to use the loop and the folder list, but to no avail.

  Hope that this will not be a too much trouble. Thank you

  Hi pengxin,.

  What room are you stuck at?

  Below is a diagram of simple block that I created which should do what you need. First of all, we get all the names of individual files, and then one by one, we read the data from the file. Since you only need the data in the first row, we will index in the array, add the name of the file, the date and time of last modification of the file to the front of the data, and then save them in a new file.

  

  I hope this helps.

  Kind regards

  Boon Chen

• my dvd player reads all movies what do I do to get it working.

  my dvd player reads all movies what do I do to get it working.

  I had this happen to my DVD player recently.  The problem was that the disc I was trying to see it used a copy protection system is not yet implemented by my DVD player.  Normally, I don't have the DVD player connected to the network, so he had not received the updates of the firmware since I bought the player.  After that I connected it, you download an update of the firmware and I could see the movie.

  My recommendation to you is to see if the manufacturer of the DVD drive has an update of the firmware of your player on the website of the company and, if so, has it, then test again.

• Read all files in a folder over and over again

  I want to develop an application that reads all files in a folder, and once its done reading these files, it reads all the files again.

  The purpose of this application is to read all the files in a folder that are stored permanently in this folder, so that when a new file is created, this file is also read by the application. Then I need to compare the date and the time in which the file was created on the effective date and time of the system, so that the path that I can get the latest file, and then I'm going to do other operations with this file.

  The thing is that I know how to read all files in a directory, but I don't know how to do to scroll the files again, to the more recent, and I don't know how to do the comparison between the timestamps, because I need to a precision of one second at the time system and time of creation of the file.

  Can someone help me please?

  Thanks in advance!

  
  

• My errased sticker product key and I can't read all the text to reactivate my windows visa. What should I do now?

  My errased sticker product key and I can't read all the text to reactivate my windows visa. What should I do now?

  Hello

  You mean the sticker on the case of the Vista operating system pre-installed from Dell, HP, Acer, Toshiba, etc.) ?

  If you do, you can contact your computer manufacturer and ask them to send you a set of recovery disks.

  They should do this for a small fee.

  To reinstall Vista using their recovery disk/s, you start from the 1st recovery disk they provide and follow the manufacturer's instructions to reinstall:

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  "How to replace Microsoft software or hardware, order service packs and replace product manuals.

  http://support.Microsoft.com/kb/326246

  And if you have never received a recovery disk when you bought your computer, there should be a recovery Partition on the hard drive to reinstall Vista on how you purchased your computer.

  The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

  Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

  Ask them to the proper key sequence.

  And if you do not score a manufacturer of recovery on your hard drive, you should be able to make your own recovery from her disks to reinstall the operating system.

  Go to programs > name of the manufacturer of your computer > then their system or recovery tools software topics for them, depending on how it is formulated.

  If you can't find any reference to it, contact the manufacturer for advice on how to make these recovery disks.

  The methods above resettlement generally do not require allows you to provide a product key during Installation, the recovery process uses the Installation product key factory to activate automatically during the resettlement process.

  See you soon.

• My CD Rom won't read all disc types

  My CD Rom won't read all disc types.

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• ONCE 1 DISC CD/DVD PLAYER READS ALL THE OTHERS LIKE WHITE

  has got an acer 5315 laptop filth single bed 1 disk. reads all the other virgins or be reformatted, I'm puzzled... any advice would be greatly appreciated.                am running vista Home Basic edition if it helps

  Hi Ronwaddilove,

  1. are you able to play these discs on another computer. ?

  You can read the following article and try to run the Fixit and see if it helps.

  Your CD or DVD drive cannot read or write media

  Hope this information is useful.

• read all of my documents in microsoft office

  read all of my documents in microsoft office. How can I convert to the original decoding. I can't open anything... even aol.

  The information below will help you to:

  http://www.Winhelponline.com/articles/165/1/restore-the-exe-file-association-in-Windows-Vista-after-incorrectly-associating-it-with-another-application.html

  Restore the .exe Windows Vista file association, after badly with another application

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://www.Winhelponline.com/articles/105/1/file-association-fixes-for-Windows-Vista.html

  For Windows Vista file association problems

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  How to set file Associations:

  http://articles.TechRepublic.com.com/5100-10878_11-6172036.html

  How do I... Change file extension associations in Windows Vista?

  See you soon.

  Mick Murphy - Microsoft partner

• Cannot modify only directory attributes of reading, all the readers all the directories.

  Original title: cannot modify only directory attributes of reading, all the readers all the direcotries.

  For some reason now all directories are read-only. I have a check only reading tab, it goes through the process of change in all files in the subdirectory (I put their scrolling), click ok. But when I go in the directory again that reading is only check again. It is on my C: dirve all directories and all the other readers, including empty directories. Any suggestion would be appreciated. Thank you
  Bit defender shows no problem.
  SdS49r

  Hi SdS49r,

  I would like to ask you a few questions to better understand:

  (a) you connected to the administrator account? because you do not have the \n(Assurez-vous if you are not in the administrator account

  (b) don't you make changes on the computer?

  (c) have you created the file read-only?

  (d) what message do you get while changing the read-only attribute?

  (e) have you been able to change the attributes previously in your computer?

  You can scan your computer, then follow the steps in the link: http://www.microsoft.com/Security_Essentials/

  Try the system restore, it restores the computer to its point earlier while it was working fine.

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.
  
  Hope this information helped!

  Thank you, and in what concerns:

  Aziz Nadeem - Microsoft technical support.
  Visit our http://social.answers.microsoft.com/Forums/en-US/answersfeedback/threads/ Microsoft answers feedback Forum and let us know what you think.