ReadyNAS Duo copy is slow and gives error 0x8007003B

Similar Questions

• I can't install any adobe application. I bought all these products and tried to d/l through the creative cloud and direct links, by DDLS trial or normal he gets 2%, then rises to 99% and gives error DW050 and WARNING DS013...  Very frustrated

  I bought all these products and tried to d/l through the creative cloud and direct links, by DDLS trial or normal he gets 2%, then rises to 99% and gives error DW050 and WARNING DS013...  Very frustrating because I've already paid for them. Is a 2nd hand computer, but I erased everything when I bought it.

  Working on a mac osx, report looks like this

  Exit Code: 7 Please see specific errors and warnings below for troubleshooting. For example, ERROR: DW050 ... WARNING: DS013 ... -------------------------------------- Summary -------------------------------------- - 0 fatal error(s), 30 error(s), 2 warning(s) WARNING: DS013: Payload {56DCC6F4-322E-42DA-A5DA-26BAD28C1E10} Camera Profiles Installer 8.0.0.0 is already installed and the session payload {539AEF15-3A2B-4A31-A587-7E90F7D9C700} Camera Profiles Installer 7.0.0.0 has no upgrade/conflict relationship with it. WARNING: DS013: Checking payloads upgrade/conflict relationships : Failed with code 1 ERROR: DW050: The following payload errors were found during install: ERROR: DW050: - Dynamic Link Media Server: Install failed ERROR: DW050: - Adobe Encore CS6_AdobeEncore6en_USLanguagePack: Install failed ERROR: DW050: - Adobe XMP Panels: Install failed ERROR: DW050: - Adobe Player for Embedding 3.3: Install failed ERROR: DW050: - Required Common Fonts Installation: Install failed ERROR: DW050: - Adobe CSXS Infrastructure CS6: Install failed ERROR: DW050: - Adobe Premiere Pro CS6: Failed due to Language Pack installation failure ERROR: DW050: - Adobe Encore CS6: Failed due to Language Pack installation failure ERROR: DW050: - Adobe Utilities CS6: Install failed ERROR: DW050: - Adobe SwitchBoard 2.0: Install failed ERROR: DW050: - Adobe ExtendScript Toolkit CS6: Install failed ERROR: DW050: - Camera Profiles Installer: Install failed ERROR: DW050: - AdobePDFL CS6: Install failed ERROR: DW050: - Adobe Extension Manager CS6: Install failed ERROR: DW050: - Adobe Bridge CS6: Install failed ERROR: DW050: - AdobeTypeSupport CS6: Install failed ERROR: DW050: - AdobeHelp: Install failed ERROR: DW050: - Adobe Premiere Pro CS6 Family: Install failed ERROR: DW050: - Adobe Mini Bridge CS6: Install failed ERROR: DW050: - Suite Shared Configuration CS6: Install failed ERROR: DW050: - AmericanEnglishSpeechAnalysisModels: Install failed ERROR: DW050: - Adobe Media Encoder CS6: Install failed ERROR: DW050: - Adobe Premiere Pro CS6 Support: Install failed ERROR: DW050: - Photoshop Camera Raw 7: Install failed ERROR: DW050: - Adobe Premiere Pro CS6_AdobePremierePro6.0en_USLanguagePack: Install failed ERROR: DW050: - Adobe Encore CS6 Support: Install failed ERROR: DW050: - Recommended Common Fonts Installation: Install failed ERROR: DW050: - DynamiclinkSupport: Install failed ERROR: DW050: - AdobeCMaps CS6: Install failed ERROR: DW050: - Adobe CSXS Extensions CS6: Install failed ------------------------------------------------------------------------------------- 
  Now as stated I have tried several different download methods, removed all firewalls & antivirus. Any Suggestions???
  

  The system configuration required

  Exit Code: 7 Please see specific errors and warnings below for troubleshooting. For example,  ERROR: DW050 ... WARNING: DS013 ...  -------------------------------------- Summary -------------------------------------- - 0 fatal error(s), 30 error(s), 2 warning(s)  WARNING: DS013: Payload {56DCC6F4-322E-42DA-A5DA-26BAD28C1E10} Camera Profiles Installer 8.0.0.0 is already installed and the session payload {539AEF15-3A2B-4A31-A587-7E90F7D9C700} Camera Profiles Installer 7.0.0.0 has no upgrade/conflict relationship with it. WARNING: DS013: Checking payloads upgrade/conflict relationships : Failed with code 1  ERROR: DW050: The following payload errors were found during install: ERROR: DW050:  - Dynamic Link Media Server: Install failed ERROR: DW050:  - Adobe Encore CS6_AdobeEncore6en_USLanguagePack: Install failed ERROR: DW050:  - Adobe XMP Panels: Install failed ERROR: DW050:  - Adobe Player for Embedding 3.3: Install failed ERROR: DW050:  - Required Common Fonts Installation: Install failed ERROR: DW050:  - Adobe CSXS Infrastructure CS6: Install failed ERROR: DW050:  - Adobe Premiere Pro CS6: Failed due to Language Pack installation failure ERROR: DW050:  - Adobe Encore CS6: Failed due to Language Pack installation failure ERROR: DW050:  - Adobe Utilities CS6: Install failed ERROR: DW050:  - Adobe SwitchBoard 2.0: Install failed ERROR: DW050:  - Adobe ExtendScript Toolkit CS6: Install failed ERROR: DW050:  - Camera Profiles Installer: Install failed ERROR: DW050:  - AdobePDFL CS6: Install failed ERROR: DW050:  - Adobe Extension Manager CS6: Install failed ERROR: DW050:  - Adobe Bridge CS6: Install failed ERROR: DW050:  - AdobeTypeSupport CS6: Install failed ERROR: DW050:  - AdobeHelp: Install failed ERROR: DW050:  - Adobe Premiere Pro CS6 Family: Install failed ERROR: DW050:  - Adobe Mini Bridge CS6: Install failed ERROR: DW050:  - Suite Shared Configuration CS6: Install failed ERROR: DW050:  - AmericanEnglishSpeechAnalysisModels: Install failed ERROR: DW050:  - Adobe Media Encoder CS6: Install failed ERROR: DW050:  - Adobe Premiere Pro CS6 Support: Install failed ERROR: DW050:  - Photoshop Camera Raw 7: Install failed ERROR: DW050:  - Adobe Premiere Pro CS6_AdobePremierePro6.0en_USLanguagePack: Install failed ERROR: DW050:  - Adobe Encore CS6 Support: Install failed ERROR: DW050:  - Recommended Common Fonts Installation: Install failed ERROR: DW050:  - DynamiclinkSupport: Install failed ERROR: DW050:  - AdobeCMaps CS6: Install failed ERROR: DW050:  - Adobe CSXS Extensions CS6: Install failed -------------------------------------------------------------------------------------
  

  The system configuration required

• Every time I open photoshop, my computer hangs and gives error KERNEL_SECURITY_CHECK_FAILURE

  So if you read the title of this discussion, you will know what it is. Whenever I run the Photoshop application, my computer hangs and gives error KERNEL_SECURITY_CHECK_FAILURE.

  I've already tried everything that I saw made online on other posts, but they do not seem to work.

  If someone could help me with this problem as soon as possible, it would be great.

  Thank you!

  Hi jollylilwoodsman,

  In my opinion, you are using an Nvidia graphics card.

  This questions seems to appear only after the recent update of the graphics card from Nvidia.

  • Navigate to the location - C:\Program Files\Adobe\Adobe Photoshop CC 2015, search the file named sniffer.exe and place it on the desktop.
  • Launch of Photoshop now and it should work fine.

  Note - moving sniffer on desktop, Photoshop will not use your graphics card.

  Another solution would be to install a previous version of the graphics driver.

  Let me know if it helps.

  ~ UL

• Hello! I am trying to install Photoshop and gives error 1 help me please!

  Hello! I am trying to install Photoshop and gives error 1

  Help me please!

  Hello

  Please see the instructions at the link below:

  Error: "unable to install". Creative cloud office

  Error code: 1

  Let us know if that helps.

  Kind regards

  Bani

• Cc of Photoshop download just guard dropping and gives error error A12E5

  Just Photoshop download keeps breaking and give error A12E5

  http://forums.Adobe.com/thread/1087843

• Vista Windows update fails to install and gives error code A 80071, 30

  Windows Update for vista not install and give the error code A 80071, 30. How do I receive the updates installed and what is this error? Stem

  Original title: windows update error code a 80071, 30

  Hello

  Method 1:

  I suggest you to disable all security software, including the Windows Firewall and then check if it solves the problem.

  Check out the link to disable the security software.

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-GB/Windows-Vista/disable-antivirus-software

  Enable or disable Windows Firewall

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  Warning: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2:

  Cannot install updates in Windows Vista, Windows 7, Windows Server 2008 and Windows Server 2008 R2

  http://support.Microsoft.com/kb/2509997

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 how to back up and restore the registry in Windows

  Important: When running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area so all available data on this risk to be lost

• After upgrading RAM, computer stops and gives error when restarting: "DISK BOOT FAILURE, INSERT SYSTEM DISK".

  Original title : OFFICE XP STOPS (MESSAGE of ERROR)

  I get the message "DISK BOOT FAILURE, INSERT SYSTEM DISK". I just added more memory to my 512 RAM. I USED MY XP TO REBOOT DISC, BUT THERE ARE ALWAYS AFTER PRESSING THE KEY 'R '. ONCE IT STARTS AND SE PAST JUST STOPS AND THE ERROR MESSAGE IS POSTER AGAIN UPWARD. I HAVE THE SAME 'MSCONFIGED' IT NORMAL TO SELECTIVE. I WAS ABLE TO GET INTO SAFE MODE, BUT NOW IT WON'T. I GET JUST THE ERROR MESSAGE.       > WHAT AM I DOING WRONG

  Hello

  You can view these methods:

  Method 1: As a first step, check to see if the hard disk becomes detected or listed in the Basic Input/Output system (BIOS). Also, be sure to change the boot order in the CMOS settings so that thehard drive is the first on the list.

  Note: To learn how, see the documentation provided with your computer or contact the manufacturer of your computer.

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from configuration can resolved BIOS/CMOS settings. Changes to settings are at your own risk.

  Method 2: If the manufacturer has installed the Recovery Console on your computer, perform the check disk to fix this.

  At the recovery console command line, type:

  Chkdsk /r

  When you restart your system, your computer will be scanned for errors and will try to correct them.

  Note: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  For more information, see:

  How to perform disk error checking in Windows XP

  Chkdsk

• FDMEE VB API introduces not and gives "error of data access.

  Hello FDM gurus.

  While working with the FDMEE data integration tool, I had to test the capabilities of script VB to FDMEE and I tried the sample script of the ERPI Administrator's guide to copy a file from 1 place to another. Unfortunately the VB API does not work and generates an error "clsAppServerDM.fInitializeMainAPI: data access error." I don't know what am I missing here.

  Thank you in advance,

  VChakravarthy

  If you format this SQL query and you attempt to run in the SQL tool like SQL Developer, you can see how there is a SQL syntax error. There is a missing expression in the "BOLD"

  PV. LEVEL_VALUE =

    ),

  He expects something like pv. LEVEL_VALUE = 1005 so the SQL query should return the file application root.

  What I would do:

  -Update FDMEE to 11.1.2.3.510

  -Raise a SR with Oracle's Support.

  SELECT MERGE)

  SELECT pv. PROFILE_OPTION_VALUE

  AIF_PROFILE_OPTION_VALUES PV

  WHERE (PV. PROFILE_OPTION_NAME = p.PROFILE_OPTION_NAME)

  AND the pv. LEVEL_ID = 1010

  AND the pv. LEVEL_ID<=>

  AND the pv. LEVEL_VALUE = 1005

  ), (

  SELECT pv. PROFILE_OPTION_VALUE

  AIF_PROFILE_OPTION_VALUES PV

  WHERE (PV. PROFILE_OPTION_NAME = p.PROFILE_OPTION_NAME)

  AND the pv. LEVEL_ID = 1005

  AND the pv. LEVEL_ID<=>

  AND pv. LEVEL_VALUE =

    ), (

  SELECT pv. PROFILE_OPTION_VALUE

  AIF_PROFILE_OPTION_VALUES PV

  WHERE (PV. PROFILE_OPTION_NAME = p.PROFILE_OPTION_NAME)

  AND the pv. LEVEL_ID = 1000

  AND the pv. LEVEL_ID<=>

  ) PROFILE_OPTION_VALUE

  OF AIF_PROFILE_OPTIONS p

  WHERE p.PROFILE_OPTION_NAME = N 'PROFILE_APP_ROOT_DIRECTORY '.

• slow and timeout error

  Hello forum members

  I wrote a program in LV2010 and works very well except for one last question.

  The program works very slowly and sometimes shows error timeout. In the program, I send a voltage to Keithley 2400 and simultaneously measure the current Keithley 2400 and 2000. I sweep the voltage using a while loop. I have not used buffer.

  Your help would be very appreciated.

  Thank you.

  Pradeep

  A few things I noticed:

  1. You should not mix GPIB and VISA to speak to the same instrument.  You should just use the entry VISA to send your order.  But if there is a VI later in driver for the 2400 set the voltage from the source, you should use that.
  2. If you insist on the construction of your own SCPI command to set the voltage of the source, make sure that the command structure is correct.  You may need to add a semicolon or an end of line at the end of the command character.  That's what I suspect causes the header not defined error.
  3. Really, you should add a delay between voltage and then perform readings.
  4. I don't like the idea of allowing the two different screws communicates on the same bus at the same time.  I've seen some strange things with GPIB.  You should sequence a little more so that you adjust the tension, wait 500ms (round number to allow things to sort out and the bus to talk to nice), read the voltage of the 2400, read the current 2000.
  5. Your back measures seem to me.  I usually use the 2400 (source meter) at a voltage of the source and read the current, then read the voltage to the unit under test with the 2000 (DMM).

• Update request for Office CD and gives error 8024002D

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: Windows Update every time I try to update as requested it starts to install, then stops and and a message saying "the component you are trying to use is on a CD-ROM or another removable disk that is not available, insert the Office XP Professional with Frontpage @Microsoft @ the drive and click ok. I do not have this disc or never had, so when I press cancell it comes up with an error code 8024002D. Can antone tell me how to get around this problem?

  Error message saying updates are required and the

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  * Title *.
  Update

  Hi Katy,.

  It seems that you try to install Service Pack 3 for Office XP, and it asks for a disc, is this correct?  If so, here is a link to Microsoft on how to install the full version of SP3, so you do not have to provide the original disks: http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=85af7bfd-6f69-4289-8bd1-eb966bcdfb5e.

  Scroll down to the section install SP3 without the original Office XP CD you will find a link to download version of the Office XP SP3 full of the file. Download this file first (it's important-about 58 M), then run it.  After the update installs successfully, you can safely delete the downloaded file.  This should solve your problem and it will not ask you to install the update more.

  See you soon,.

  Barbara

• My Vista computer will not be stopped, randomly freezes and gives error Logon process has failed to create the security options dialog

  I have a laptop that has recently (in the last month) developed several questions. These issues are: computer does not, get the logon error message failed to create the dialog box options security when I hit Ctrl alt delete, computer hangs when more then another program is open. How can I solve them? My system is Vista Home premium 32 bit any help is appreciated.

  * original title - several issues need help *.

  Hello

  I forgot to include which could help with the connection of safety problem:

  How to restore the security settings to a known working state?
  (For Vista and XP)
  http://support.Microsoft.com/kb/313222

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Epson Artisan 700 printer does not print and gives errors in Windows 7

  I HAVE AN EPSON ARTISAN 700 PRINTER AND IT STOP PRINTING AND ALL THE LIGHTS FLASH AND I GET AN ERROR MESSAGE INDICATING THAT AN ERROR HAS OCCURRED WITH THE PRODUCT.

  * original title - WHY IS ALL LIGHT ARE FLASHING AND the PRINTER WANT PRINT.*

  Hello

  · Did you receive the exact error message?

  · You receive an error with the error code?

  · Do you remember all the recent changes on the computer before the show?

  · You try to print from the internet explore?

  You can run the patch from the link below: why can I not print? : http://windows.microsoft.com/en-US/windows7/Why-cant-I-print

  Alternatively, you can follow the procedure on the manufacturer's Web site. Link for reference: http://er.epson.com:8001 / early

• Acrobat Pro quit job and gives error 213:8?

  He worked many years. Now, suddenly I can't open an existing PDF document, OR even to open office program at all. I get a configuration error that says there is a problem with the license of this product - restart the computer and restart the product. But he keeps doing the same thing over and over again. Can anyone help with this? I have Adobe Acrobat X Pro Office.

  Thank you

  Linda

  Did some more research and found a suggestion to open as administrator.

  Open just fine, and now I have no problem. So I'm good for a

  little longer!

• How can I use it to avoid the slowness and the error.and more I do not happen to my android?

  Be descriptive saying "playing a video is always rough.

  What device?

• KB951847 X 86 settled after the successful download and gives error code 0 x 643 how do I correct or I give up?

  TURBO TAX REQUIRES .NET @ LEVEL 3.5 BUT IT WONT INSTALL.

  Hello

  You did changes to the computer before the show?

  Please follow the steps from the link below.

  http://support.Microsoft.com/kb/976982