ReadyNAS Pro 6 is stuck at the start...

Similar Questions

• I have a Macbook pro (2011 model). It gets stuck on the start screen on to half way through commissioning. This happens whenever the mac turns on. The problem is solved when I reinstall Yosemite to boot to Recovery Mode disk utility.

  I have a Macbook pro (2011 model). It gets stuck on the start screen on to half way through commissioning. This happens whenever the mac turns on. The problem is solved when I reinstall Yosemite to boot to Recovery Mode disk utility. However, the next time you start, the startup process is blocked to halfway to new (on the screen with the toolbar and the status of apple). I want a more permanent solution to reinstall the operating system every time. Would appreciate someone's suggestions and thanks in advance.

  Replace your hard drive.

  You have a backup of trust? If not, buy a disc of exterrnal for that as well.

  The progress bar from the left end at the beginning of the commissioning indicates that your drive has been so damaged, it could not be mounted. Five minutes of progress bar is shown as it does the equivalent of disk utility (ERD [Directory]). If you have reinstalled several times and the problem is not fixed, your drive is in solid form.

• S90 stuck to the start screen

  My S90 is stuck at the start-up screen. It shows the screen of stand for hours now. If I change the switch it will not swtich off the phone, but it restart again to the start screen. What should I do with it?

  I felt that I could let it run out of battery, but I don't know how the phone can operate on a screen for single cabin with just the lenovo on-screen log. Also don't know if once I reboot it wouldn't have the same problem.

  Any advice how to fix this?

  
  

• The Cliq is stuck on the start screen.

  Hey guys, after a normal day of use with my Cliq from 07:00 I got around 17:00 and put it on the charger, as it was almost dead, I went to charge less than an hour with it and now it is stuck on the start screen of Motorola with the small black bar on the left. I charge my phone all night every night and do not use it much at all, but it lasts and I wasn't there to look at what had happened, so I don't know if there was any discrepancy prior software other than seeds from basic mentioned by others.

  Charles, you are still able to boot into Recovery Mode and learn the triangle with the exclamation point? If you can, press the keys ALT and L at the same time to access the Recovery Menu.

• Stuck at the start-up screen

  Hi, I use Jdeveloper 12.1.3 and the extension of the ADF Mobile on Mac OS X Mavericks. iOS 7.1 and Xcode 5.1.1

  If I make an application with a HTML file and deploy Simulator iOS, the app works great.

  If I apply with an AMX-page the and deploy on iOS Simulator, the app is stuck at the start-up screen. "Loading...". »

  Any ideas? I tested the "Navigation" public sample and deploy and works very well.

  Concerning

  Thomas H

  I looked in the debugging using the iOS Simulator. The problem causing my problem was not supported for encoding. I used ISO-8859-15. Changed to UTF - 8.

  Thank you for you detrilles Sudipto link on debugging =)

  -Thomas H

• Product key not recognized during a repair of xp pro sp2 on a genuine xp pro sp2 disk. stuck on the main screen of the product.

  After starting problems on my Toshiba satellite with xp pro sp2, I booted my xp pro sp2 disk and did a repair instead of a reinstall software.  He went through the motions, removed the sys files, copied them back and so on.  Then he asked my product key and I typed in it and it does not recognize.  It's a real bought copy of xp pro sp2.  Now, I'm stuck on the main screen of the product.  When I start the laptop on the xp disk it blue screens, the only option I have is to enter a product key in the configuration...  I have my receipt for my xp pro disk and product key for certification sticker.  Help, please!

  "XP MCE Pro? That is not normal! It would be one or the other (AFAIK). Here is an example:

  http://cdn2.ioffer.com/IMG/item/811/353/46/o_XyuQav94U1MQ0Ci.jpg

  If the hybrid you mention is the real thing, it's new to me! I know that some have described as a superset of Pro MCE, but I never used this version, so I can't tell you definitively that a COA sticker wouldn't this combo of terms...

  In addition, the term 'Enterprise Edition' implies something not legitimate. I do not think that Microsoft has never used the term marketing for Windows.

  If you had a legitimate retail version of Windows XP (any version) that is not used on another PC, you can perform a Clean Install (not a repair installation), using this key (not the key COST laptop). The only way you can use the key from your laptop COST would be if you used the correct installation CD - a generic OEM version of the corresponding XP (MCE?) version. In this way, you can perform a clean installation or a repair installation.

  Have you looked at the links I posted? What do you mean by "boot option? The instructions were to press the zero key while turning on the laptop. You are not supposed to enter the OS! The recovery partition is quite distinct.

  If your laptop does not a recovery partition, you should be able to get the correct recovery CD for this Toshiba - by Toshiba or you might need to find a reputable eBay merchant, etc.. Restoredisks.com, who has a good rating from Better Business Bureau, they probably sold too.

• Premiere Pro CC 2014 crashes at the start with sequelae

  Hey, I tried almost all the suggestions I've seen on the forums except the re-installation of my OSX.

  At Pref Delete, Permission, writing and reading, creative cloud reinstaling, used the creative cloud cleaner, started in safe mode, update the "CUDA" video drivers, I even went in the plugins folder, deleted file is stuck, it will start after that, but if I just click on file in the menu it crashes instantly and if I righclick on a file that sound on a sequence it crashes... I don't really know what else to do! I hope someone could help me!

  Here is my card and my crash report

  Model name: MacBook Pro

  Model identifier: MacBookPro10, 1

  Processor name: Intel Core i7

  Processor speed: 2.7 GHz

  Number of processors: 1

  Total number of Cores: 4

  (By heart) L2 Cache: 256 KB

  L3 Cache: 8 MB

  Memory: 16 GB DDR3 1600 MHz

  Status: Ok

  The system version: OS X 10.10.3

  Chipset model: Intel HD Graphics 4000

  Bus: integrated

  VRAM (dynamic, Max): 1024 MB

  Color LCD:

  Display type: LCD retina

  Resolution: 2880 x 1800 retina

  Retina: Yes

  Per pixel: 32-bit color (ARGB8888)

  Name of the media: APPLE SSD SM768E media

  Size: 750,42 GB (750,418,227,200 bytes)

  Media type: SSD

  __________________________________________________________________________________________ ___________________________

  Process: Adobe Premiere Pro CC 2014 [1452]

  Path: / Applications/Adobe Premiere Pro 2014/Adobe Premiere Pro 2014.app/Contents/MacOS/Adobe first Pro 2014 CC CC CC

  ID: com.adobe.AdobePremierePro

  Version: 8.2.0 (8.2.0)

  Code type: X 86-64 (Native)

  Parent process:? [1]

  Responsible for: Adobe Premiere Pro CC 2014 [1452]

  User ID: 501

  Date/time: 21:10:26.142 2015-06-01-0400

  OS version: Mac OS X 10.10.3 (14D136)

  Report Version: 11

  Anonymous UUID: 6BA711B7-4D71-3935-2250-E77176DE1873

  Time since started awake: 760 seconds

  Crashed thread: 0 dispatch queue: com.apple.main - wire

  Exception type: EXC_BAD_ACCESS (SIGSEGV)

  Exception codes: KERN_INVALID_ADDRESS at 0x00007fff61cbffff

  VM regions near 0x7fff61cbffff:

  Battery 00007fff5f400000-00007fff5fc00000 [8192K] rw-/ rwx SM = PRV thread 0

  ->

  00007fff61cc0000-00007fff61cf7000 [220K] __TEXT r-x/rwx SM = COW/usr/lib/dyld

  Request for clarification:

  / Applications/Adobe Premiere Pro 2014/Adobe Premiere Pro CC 2014.app/Contents/Plug-Ins/Common/SurCodeAC3Encode.bundle/Contents/MacOS/SurCodeAC3Encode CC

  Thread 0 crashed: Dispatch queue: com.apple.main - wire

  0 libstdc ++.6.dylib 0x00000001010c8891 0x1010c8000 + 2193

  1 dyld 0x00007fff61ccf871 ImageLoader::recursiveInitialization (ImageLoader::LinkContext const &, unsigned int, ImageLoader::InitializerTimingList, & ImageLoader::UninitedUpwards &) + 305

  2 dyld 0x00007fff61ccf6f8 ImageLoader::processInitializers (ImageLoader::LinkContext const &, unsigned int, ImageLoader::InitializerTimingList, & ImageLoader::UninitedUpwards &) + 138

  3 dyld 0x00007fff61ccf969 ImageLoader::runInitializers (ImageLoader::LinkContext &, ImageLoader::InitializerTimingList const &) + 75

  4 dyld 0x00007fff61cc5063 dyld::runInitializers(ImageLoader*) + 89

  dlopen dyld 5 0x00007fff61ccc1d1 + 578

  6 libdyld.dylib 0x0000000105e3d857 dlopen + 59

  7 com.apple.CoreFoundation 0x000000010123c9c8 _CFBundleDlfcnLoadBundle + 152

  8 com.apple.CoreFoundation 0x000000010123c190 _CFBundleLoadExecutableAndReturnError + 528

  com.apple.CoreFoundation 9 0 x 0000000101259242 CFBundleGetFunctionPointerForName + 50

  10 com.adobe.ASLFoundation.framework 0x000000010089aaaf ASL::Module:GetProcAddress(std::string_const&) const + 383

  I simply delete this file premiere*.app-> SurCodeAC3Encode.bundle, because in my case - it crash at startup.

• Thunderbird is stuck on the start page of mail (Mac, Mavericks)

  Thunderbird has been working well on my Mac, but after the last update + restart, it seems to be stuck on the mail start page. Here is a screenshot: http://i.imgur.com/gKFjEaH.png

  When I click on 'read messages', it is said so "host contacted, the connection information," has no effect. I tried to drag the window from left to right to see if something is missing (it is not), see > > records > > all (it is already) and go > > folder > > my e-mail address > > Inbox (nothing happens).

  He can still send messages without a problem. I can't get to the Inbox.

  Any other ideas? Is this some sort of bug? Very much appreciated.

  Given that you cropped the image, I have to ask. The pane in what folders should appear seems to be present. You say that it's completely empty? Not even a single entry?

  If so,.
  Restart Thunderbird in the Help menu with the disabled modules and see if that solves the problem.

  Then, open the profile folder (there is a button in the troubleshooting information in the Help menu to do it.) close Thunderbird and delete or rename the files to panacea.dat ANDS foldertree.json

  If who disobeys, repeat and delete the session.json file. The first two are simply cache files. The last one contains some parameters of the interface as the reading pane is enabled or disabled and what tabs are open. Really, I don't think that it is an issue, but that he loss of settings is only slightly inconvenient if the other two don't work.

• HP G6 Windows 8.1 sometimes stuck on the start up repair/diagnostic screen

  I have a Pavilion G6 accompanying win 8 and I've updated to 8.1.   Normally, works very well.  But sometimes if it is not stop properly, or after updates, it gets stuck in the rotating balls forever.   Usually after 3 stops forced, I get repair folollowed preparation of the diagnose sceens pc, and then it works when I select restart.    A few times I had to go through the process several times, but so far, it has always started.

  Any suggestions?

  Thank you.

  Some things you could try for now.

  Make a diagnosis via hard drive BIOS

  Restore the default settings of the BIOS

  http://support.HP.com/us-en/document/c02693833

  Run the Memtest86 to test your RAM from there, not the paid version:

  http://www.Memtest86.com/

  Consider changing your CMOS battery.

• ReadyNAS Duo v2 impossible to access the start menu

  Hello

  I am new in ReadyNAS, I bought this one for a long time but only used for a few days... I try to use again, I tried to upgrade the firwmare the/admin /, but surely a bug appear, because after restart-auto, I can not access the /admin/ with my own password or the default password factory.

  So, I am trying to go to the Start Menu to use that reinstalling the operating system. I & pressed the reset button, press the power button and wait... wait... wait... the 5 LEDs light up but that never happen :-(

  I have only 2 LEDs for disks (2 at the same time), and then a few seconds later, only the right one.

  Maybe I can try with a Boot USB Recovery but I can't find where to download (the search engine return nothing on the download page)

  Thanks for your help!

  Hi lakano,.

  Welcome to the community!

  Can you confirm the version of your ReadyNAS unit HW? It could have been labeled as ReadyNAS V2, but it could be a V1. Send me a PM with S/N so I can check.

  Kind regards

  BrianL
  NETGEAR community team

• Windows 7 Pro - WAU is missing from the start menu

  Hello. Thanks in advance for your help. I have four computers with Windows 7 Pro. None of them are in a domain, and the users are administrators with disabled UAC.

  A computer that I am wanting to upgrade to Ultimate does not show the "Windows Anytime Upgrade" in the start menu. WAU is in the other three systems start menus, but not this one. YES - I am an administrator and it is professional edition. NO - I'm not on a domain and have not tinkered with Group Policy settings.

  When I go into the properties of the computer, the "get more features with a new edition of Windows 7" is also absent on the shot I want to improve. Any ideas?

  Where did you get your Windows 7 Professional licenses? Is it volume licensing?

  If you are unable to find the Express upgrade program, first of all, make sure that you are running a supported product, WAU is not compatible Windows 7 Enterprise or Ultimate because it is the most comprehensive editions of Windows 7. If you use the home edition Premium or professional and you are not able to find it, click Start > click on Control Panel. Click in the view by: list box and click large icons, then double-click the Anytime Upgrade Panel element.

  WAU is supported in the distributions of volume of Windows 7 Professional license?

  By default, it is disabled. It is likely, is likely to make an Express upgrade, but may be disabled by your network administrator in order to avoid upgrades of licenses for the company. Consulter consult with the person who manages your computer, find out if you can upgrade the machine.

  If the administrator access to the machine, try the following, click Start, type: gpedit.msc, and then press on enter on your keyboard.

  Expand User Configuration

  Expand Administrative Templates

  Expand Windows components

  Click Windows Anytime Upgrade

  Double-click on prevent Windows Anytime Upgrade of the race

  Double-click on prevent Windows Anytime Upgrade to run, select enabled, and then click on apply and OK

  Exit group policy

  Click Start, type: gpupdate.exe/force

  You must restart the computer and then you should be able to make an Express upgrade.

  Releasing it's easy: with Windows | ActiveWin | Laptops | Microsoft MVP

• Cannot start Lightroom 6 (standalone) after installation - stuck at the start with scope screen not responding error

  Hi all

  As stated above, I am unable to start Lightroom 6 (standalone) after installation. I am able to launch, but I'm stuck on the boot screen (lightroom logo 6) with bezel does not no error. Would be grateful for any help, thank you very much!

  Just a suite, I use Windows 7 (x 64). I talk with the cat from adobe and I was told to create a new Administrator windows account and reinstall LR by using this new account.

  It worked for me, I am able to successfully access LR 6 using the newly created administrator account. I tried to follow up with another request - I have what patches can implement to my current user account so that I can access LR 6 using that account (and not the new windows user account). Unfortunately, I was told that cat Adobe does not support LR 6 and I am directed to ask my questions here.

  Thanks a lot again!

• First Pro CC 2014 crashing at the start of the application, exhausted solutions?

  I've seen similar bugs offered for this but I tried everything to nothing does not.

  Version of the CC 2014 body crashes at startup, just after the start screen.  Wrong to the actual application, just instantly white outside with "Adobe Premiere Pro CC 2014.0 has stopped working".   Here is the log for details of the problem of Windows:

  Signature of the problem:

  Problem event name: APPCRASH

  Name of the application: Adobe first Pro.exe

  Application version: 8.0.1.21

  Application timestamp: 53c7b17f

  Fault Module name: dvaui.dll

  Fault Module Version: 8.0.1.21

  Fault Module Timestamp: 53 c 76970

  Exception code: c0000005

  Exception offset: 00000000002f4e39

  OS version: 6.1.7601.2.1.0.256.48

  Locale ID: 1033

  Additional information 1: 4 d 34

  More information 2: 4d34d3a7ae19b5763432cd60b19af792

  3 more information: 0fe8

  Additional information 4: 0fe86a744bc3a8e89178eceb53cd1d4c

  I received the advice of others and uninstalled agency CC 2014, rebooted, update my records from Nvidia, rebooted, reinstalled agency CC 2014, rebooted, tried to run the application, but same accident persists.  Others also said something about changing permissions for 'something';  I tried to change the permissions for the cache folder that I use but not sure how effective it is, or what to change EXACTLY for permissions, IF this is the problem.

  Any advice, experience with this problem, or discussion would be appreciated.  Thank you!

  ----------

  LAST UPDATE 27/07/14

  Uninstalled all Creative Cloud components / applications completely, used Adobe CC cleaning tool to remove the cloud remains.  Reinstalled only agency and Media Encoder 2014 and same thing for the body, instantly hangs at startup.  I, however, had a few interesting weird encoder errors and failures during his installation through creative cloud desktop.  Here are some pictures of the error log:

  

  I feel that something is wrong from the start, perhaps something within dynamiclink that crashes body / gives also install errors to encode.

  Any help or thoughts are appreciated!

  LAST UPDATE ON 28-07-14

  
  

  Suggestions of preferences is, indeed, where was the problem. In my case, there was a Premiere Pro Preferences file which was in conflict with a folder of pref anterior body under Windows 7 Sync Center. I guess that's the equivalent of Windows preferences Mac questions, so be sure to check if you have synchronization conflicts, I guess, lol. Hope this helps anyone with similar problems out there!

• HP pavilion elite hpe 500cs: stuck at the start-up screen

  Hello
  I bought gtx 1060 to my hp pavilion elite hpe 500cs pc, but I can't front the start screen (cannot even get into the bios settings). I inherited bios with the latest version 7.15 which is avalible for my motherboard. The card worked on power and different Mr. b. is sufficient. I also have 1 beep, that the long break and followed 3 short and fast beeps long beep.

  Any ideas?

  Your comparison of different systems and not being is not specific about the other tested machine.  It is like comparing a Citroën with a Renault. (Could not stop myself, realizing your in CS).  The HPE 500cs, as you say, is Legacy BIOS.  The new GTX 1060 is UEFI and would not work in the HPE without a hybrid BIOS from the manufacturer of the card.

• HP g72-260us: HP g72 stuck at the start, none of the function keys work how to fix this problem

  Laptop stuck in the market and none of the work of function keys that I tried to unplug the HARD drive and reboot but it remains always stuck in the HP screen and function keys still don't work. what I can do to solve this problem too I just got install a new HARD drive and the operating system. And the driver, it worked very well. then I stopped it and when I went to restart what happened please let me know what to do
  Thank you.

  The hard reset worked thanks for the help!