ReadyNas remote network of sheet errors

Similar Questions

• Cisco ASA 5505 unable to access the remote network

  Hello

  I have a Cisco ASA 5505, with 50 basic license, which is connected directly to the Modem cable with a public IP address. I have configured and active VPN on the outside interface. When connect us, we connect well without error, but we are not able to access all the resources on the remote network.

  ASA IOS version 8.2 (5)

  Remote IP network: 10.0.0.0/24

  VPN IP Pool: 192.168.102.10 - 25

  I have attached the config: llc.txt

  Please let me know if you have any questions.

  Thank you!

  Hello

  Try adding NAT 0 because inside subnet--> subnet distance

  NAT (inside) 0 access-list TEST

  TEST access ip 10.0.0.0 scope list allow 255.255.255.0 192.168.102.10 255.255.255.224

  HTH

  MS

• ReadyNas remote control device

  Hello

  I don't see any device on readynas remote (on readCloud Agent (PC)).

  My connection is correct.

  If I use Readycloud on the web I see my 2 NAS (after click on Find button)

  On the Readynas Replicate web site, I see my 2 NAS

  ReadyNas 212 V 6.6.0.

  6300 port is not enabled on NAS

  Thank you

  I contacted support.

  READYNAS REMOTE is no longer compatible with OS 6.6.0. (or 6.5?)
  I use the READYCLOUD client

  Good bye

• Try to update the network of 1606 error Java 24 get is not found

  I'm trying to update Java, I have currently updated 19 which is obsolete to day 24 trying to install it and get (network not found Error 1606) what is the problem? It is XP home edition SP3 service / 32-bit. Everything has been updated.

  Hello
   
  
  These errors are InstallShield error codes that indicate that an action failed during the installation process.
  Method 1.
  Please try to download and install Setup offline official website of Java:
  http://www.Java.com/en/download/help/download_error_codes.XML
  
  Method 2.
  Step A.
  You can go to Control Panel then programs & features and make sure that all entries of Java are uninstalled.
  
  Step B.
  Then download and install the updates of Java from the link below
  http://Java.Sun.com/javase/downloads/index.jsp
   
  I hope this helps.

• Unable to connect to remote PowerShell and get error message.

  I have two computer to Windows 7.

  Unable to connect to remote PowerShell and this error message

  nvoke-command - computername XXXXXX - scriptblock {}
  get-process} - administrator credentials
  [XXXXXXX] failed to connect to the remote server XXXXXX with the
  error message: WinRM client cannot process the request. If the
  authentication scheme is different from Kerberos, or if the client computer is
  not joined to a domain, then HTTPS transport must be used or the destination
  machine must be added to the TrustedHosts configuration. Use winrm.cmd
  to configure TrustedHosts. Note that computers in the TrustedHosts list might
  do not be authenticated. You can get more information about it by running the
  following command: winrm help config. For more information, see the
  about_Remote_Troubleshooting help topic.
  + CategoryInfo: OpenError: [XXXXXX], PSRemotingT
  ransportException
  + FullyQualifiedErrorId: ServerNotTrusted, PSSessionStateBroken
  PS C:\windows\system32 >

  PS C:\Users\Administrator > Invoke-Command - ComputerName XXXX - ScriptBlock {get-process} - administrator credentials
  [XXXXXX] failed to connect to the remote server XXXXX with the following
  error message: the client cannot connect to the specified destination in the
  request. Verify that the service on the destination is running and that he accepts the
  applications. Consult the logs and documentation for running management service
  on the destination, most IIS or WinRM. If the destination is the WinRM
  service, run the following command on the destination to analyze and configure the
  WinRM service: "winrm quickconfig". For more information, see the
  about_Remote_Troubleshooting help topic.
  + CategoryInfo: OpenError: (XXXXX:String)], PSRemotingTranspo
  rtException
  + FullyQualifiedErrorId: CannotConnect, PSSessionStateBroken

  # Outgoing connection is fine because I can connect to a different machine here. However incoming connection does not work

  # Tried several things like "Enable-PSRemoting - Force." and it starts Properperly

  # And since I put the machine in workgroup, as well run "Set-Item WSMan: \localhost\Client\TrustedHosts * ' (it is running successfully as well)

  # Infact WinRM QuickConfig will not work.

  # And tried with and without firewall. and also applied several patches, but has not solved the problem

  Please notify

  Original title: WinRM

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum
  
  
  If you give us a link to the new thread we can point to some resources it

• VPN site-to-Site: several remote networks

  Examples of VPN Site to Site ASA configuration that I have met has only a single network at both sites.

  If the network/remote site multi-network for example DMZ1, DMZ2, etc. from the INSIDE how can it be added via the wizard of Site to Site VPN ASDM.

  Thank you.

  Hello

  I have not seen an example of specific configuration with the addition of several networks for tunnel l2l IPSEC via ASDM.

  Generally speaking, you would just follow the same process in the Sub URL, but add all the multiple networks local and remote networks that you want to be protected IPSEC.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00805a87f7.shtml

  http://www.Cisco.com/en/us/docs/security/ASDM/6_1/user/guide/vpn_wiz.html#wp999348

  Kind regards

  Arul

  * Rate pls if it helps *.

• EZVPN Mode of Extension of remote network

  Hello world

  I'm having the extension to the network mode remote ezvpn connecting to the server using pre-shared key authentication ezvpn. The remote router in network extension mode is on a dynamic IP. Now, every time the IP address on the remote router changes the its ISAKMP remain in State QM_IDLE even with peers who were the previous IP addresses of the remote router. When I connect with a VPN client software ezvpn Server tunnel for this customer pulls as soon as customers disconnects.

  How can I do the same thing for the remote router in network extension mode?

  Having this problem with the extension of the remote network it could easily deplete my resources ezvpn (only 10 tunnels IPSec allowed) if the IP address changes quite often on the remote router.

  Thanks a lot for your help.

  Kind regards

  Remi

  It looks like a bug. Use "sh cry his det isa" to see if KeepAlive is indeed active and "deb cry isa" to see that they are sent (you need the "periodic" option to check). IPSec security associations are deleted when IP address changes? Check with "sh cry ipsec his."

• Access to a remote network through VPN remote access

  Hello

  I'm having a problem with users who access VPN from home.  We currently have 3 offices facility, as shown below.  When I VPN in the Philadelphia office, I am unable to access the resources of Connecticut offices or North Carolina.

  The VPN subnet is 192.168.10.0.  Inside the office of the PA, I have no problem with NC or CT.  I have to add a static route from the Pennsylvania Treasury and NC?  If so, could you give me a hand with the correct syntax?

  Office <-----------IPSecVPN---------->Office <------------IPSecVPN------------->Office of Connecticut from Pennsylvania, North Carolina

  192.168.5.0                                                            192.168.1.0                                                        192.168.2.0

  Hello

  Yes, basically the ASA accommodation the customer VPN service in this case well enough is the same configuration related to two sites with the exception of course which is obvious

  • Networks/subnets
  • Different ACL for each VPN L2L

  Although naturally the problem for me is the WRVS4400N configuration.

  Basically, you do the same things on this unit than the other remote site.

  You add the VPN pool as another remote network for VPN L2L configurations. You also confirm that there is operation NAT0 for this network also. I don't know I can help you there as I do not know the device.

  Can you please mark it as answered and evaluate other useful answers

  Naturally ask for more and I'll try to help you if I can

  -Jouni

• Can I use private as Source IPs from a remote network IP addresses while building the IPSec tunnel?

  Can I use private as Source IPs from a remote network IP addresses while building the IPSec tunnel? If not why? If so, how?

  Your explanation is much appreciated.

  Hi Deepak,

  In such a situation, you usually NAT traffic that goes to the internet, but exempt traffic that goes through the VPN, because it will be wrapped in packages with public IP (tunnel) addresses. You can use the same IP address on your interface in the face of internet for the NAT/PAT and source of IPSEC Tunnel.

• How to configure the VPN LAN to access the internet from the remote network

  I have set up for our project site to another Office VPN. Please join.
  Now I have already configured Site to site vpn between ASA 5510 and 1841 router.

  HQ LAN

  Branch of the LAN
                   10.2.1.0/24 > ASA 5510 1841 > > INTERNET < 1841=""> <> 10.30.3.0/24
  ^
  ^
  ^
  ^
  Call Manager
  No. 2851
  Now access from branch LAN LAN of HQ each other.

  I face problems that are
  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH
  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?
  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  Please give advise me how should I do.

  Hello

  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH

  Answer:

  You must configure the NAT and crossed to the ASA HQ so that the VPN branch router provides LAN and u-Turn, access to Internet of the SAA.  You must first seup NAT for the branch on the SAA router subnet, then you must type the command:

  permit same-security-traffic intra-interface

  Here's a great example for VPN client hairpining.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?

  Yes, you can

  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  You must change your subnet VLANS to be different from the subnet HQ voice phone IP VOice VLAn, it should be fine.

  Kind regards

  Mohamed

• SRM 5.5 - the remote server returned an error: (503) server unavailable, could not create SSL/TLS secure channel

  Design:

  2 vCenter VMs version 5.5 on new W2k12. x. related and the same use facilities key SSO (default installation)

  2 x fresh install of the SRM VMs version 5.5

  20 + hosts vSphere 5.5 with DR/HA configured and working. Two dvSwitches (one per site) configured with the groups of port / VLAN work

  Question:

  Installation goes well until I needed to activate the Plugin SRM in vCenter.  Plugin called "Plug-ins available" and I click on the link 'download and install '.

  I had two separate fouls on both servers vCenter, both with same errors if it is compatible.

  Errors:

  (attached file viclient-3 - 000.log)

  The request has been aborted: could not create SSL/TLS secure channel.

  (attached file viclient-3 - 000.log)

  The remote server returned an error: (503) server unavailable

  I guess that the two are linked and probably something with SSO.  Post installation on each server vCenter vCenter, at the level of the vCenter, I added the "Domain Admins" AD Group with all permissions and then properly connected and built the group with this set of credentials.

  I need help to debug this further.

  Thank you

  ************

  < < Updated > >

  Seems the features and functions are NOT present so you don't not sign in as '[email protected]' (SSO account by default for this "basic" configuration)

  But even with this connection, I have noticed that there is NO option in the webclient service, to perform the installation of a vCenter plug-in.  It does not appear in the vSphere Client (see images).

  I also found it weird that the web client to vCenter illustrates SRM roles but the traditional client does not work.

  Maybe it's a clue to the root cause of...

  Post edited by: ArrowSIVAC 2013-10-07 to provide more details and attachments

  Post edited by: ArrowSIVAC, this is related to the case of support for vmware 13384832210 This problem is solved.  Several pieces here. (1) vCenters were installed secretly with local account as own databases, and this is how I usually do things (2) MRS. servers were built as separate virtual machines, VMWare vs guides guess and documents in anticipation of your SRM installation on the same server as vCenter Documentation / Installer is not clarified that you MUST use domain for MRS accounts in the multiplayer linked site facilities and if you do not, the installation is completed without error, but resources will not work. Errors have for client plugin does not work. It was the symptom, the reason was that the SRM service did not work.  The service would not start and only an error in the Windows event log is 'vmware-dr stopped service' is because the connectivity issue of MRS to vCenter hosted the new SQL instance database SRM. The SRM database has been installed on the instance of vCenter server as vCenter database.  And just like the installation of default vCenter I chose localhost\administrator for database owner.  The database was filled with tables, but SRM has connectivity problems.   The fix for this was to add "domain\user" (called mine SRMAdmin and added as a member of domain admin), add this user in SQL in the list of database users and then promoted as the owner of SRM database and define the rights on DBO. This fixed the first issue. Second issue was that SRM installation set the DSN system identification information, but does not specify that they must also be domain based accounts.  The installation program is not not clear here and should only allow user domain\username when installing. After several attempts because of the root and installation methods different tried, how to get the installation complete and properly configure was to log on to the system AS the example domain account: domain\srmadmin = > Configuration System DSN by selecting "How should SQL Server verify the authenticity of the login ID?"  "with integrated Windows authentication', and then the installation of SRM to the"Enter Database user credentials"value"domain\srmadmin ".  Then and communication services to the vCenter SRM hosted DB database will work correctly. < See images attached benchmarks >

  attached files

• "The remote server returned an error: (502) Bad Gateway" while matching Protected Site VC and recovery Site VC in VMware SRM

  Hi all

  I am trying to Setup VMware SRM 4.1 groups. I had configured hitachi usp vm storage based array replication in both sites.

  Now when I try to pair the two sites vCenter, I get an error at the end of the phase of matching as message "the remote server returned an error: (502) Bad Gateway ' on the protected site. But surprisingly, I am able to match both the vCenters on the recovering site.

  Please help me to get the problem.

  Thanks in advance,

  Sanjeev

  Run telnet server vCenter/SRM protected site to the recovering site server vCenter/SRM:

  Telnet IP_ADDRESS 80

  Telnet IP_ADDRESS 443

  You succeed?

• plugin VMware update manager returns with "the remote server returned an error: (404) not found."

  Hello

  We have recently updated our virtual Center Server to version 4 and now when I try to download and install from the page manager plugin vmware update manager plugin is back with "the remote server returned an error: (404) not found"

  Has anyone had this problem before and eventually worked out how to fix this?

  Gregg Robertson, VCP, MCSE, MCSA, MCTS, MCITP

  You are welcome!!

• Portege R830 sees network cannot connect - error 628

  Hello

  I want to use my SIM card to establish an internet connection on a Portégé R-830.
  Inserted the SIM - cad, startup Toshiba Wireless card manager, enter PIN, vor research network: "o2 surf" found, perfect signal strength
  But then: either he gives up the connection after 10 sec without a word process, or he is able to connect but not of the internet and a few more seconds later I get all sorts of errors ending with no link found or no error at all.

  In addition, I tried the orginal Connection Manager form O2 but same problem, but it gives me an error report:
  You have been disconnected (Error 628).

  On my cell phone, all right.

  Hello

  If the use of a different SIM card worked properly under Toshiba Wireless manager then I guess your first SIM card isn't ok.

  Means of error 628: the connection has been lost by the remote computer before it could be completed.
  This can be caused by computer or ISP (internet service provider), for example, this may be due to a problem of signal strength.

• HP Officejet Pro 8610: two printers on the same remote network model will not be printed, but local will be

  I have two furniture stores that are run on a windows sbs2012. Recently, both off my all in printers are down in the same week. The first was at the location where the server is actually housed. I bought a HP Officejet 8610 and managed to put in place without problem a lot via a wired network connection. So I decided since who went to buy the same model for my remote which is also connected, but it has a wireless access point. I was not able to get anything to print from my main software called profit systems. I can get things to print to the shared remote drive. I tried uninstalling and reinstalling, but even if connected as long as administrator I get a error that reads "this operation has been cancelled due to restrictions in effect on this computer. Please contact your system administrator. I put it up as both just and redirected network and it shows it as ready in the State, but after it clears the queue that nothing prints. I checked firewall settings and all with HP is checked on. I'm pretty computer but I am full of ideas. Help, please!

  So after that I lost two days of my time and more than two hours of my time of I.T. guys it came to our attention that the driver IS NOT SUPPORT this model of HP JO 8610 redirected remote office printing! HP really, really?  So we have to install the driver 8600 on the server and local computers to get things to print. Problem solved, but it's just sad that this was the problem.