rebuilt drive ReadyNAS 104 replaced always display data degraded data

Have a 104 - drive in slot 1 readynas failed-

tested the new drive all tests

replaced by model and brand

It detects and rebuilt volume showing raid 1

Once rebuilt still happens with degraded volume

running latest firmware

Have you tried restarting and once rebooted begins the rebuilding process again?

Someone has any ideas

Thank you

Well I would like to back up the data to another drive if you can (do not try and replace the existing data).

Then with only good new records in the NAS do a factory default (erases all the data, settings, everything) and restore your backup data.

Tags: Netgear

Similar Questions

  • ReadyNAS 104 - Drive replacement / addition of training

    BLUF: Bought 2 new red WD 3 TB disks (WD30EFRX) drives to add to my current 3 x 1 TB. What drive can I delete and in what order? Add to add and to remove the 4th and wait?

    To make the bottom at the front line should give you an idea of what im asking, I did some research on how to add or replace drives, but because I don't have that 3 disks in my 104 I just want to Im sure to do it correctly.

    I bought this ReadyNAS for redundancy of the data on my network (media etc.), so I use my old workstation leads in NAS (I know bad idea, but I have already built the table before the search).

    Here are the disks and their SMART specifications:

    Model family:     Western Digital Caviar Green
    
Phone model:     WDC WD10EADS-11M2B1
    
The data SMART attributes Structure revision number: 16
    
SMART vendor specific attributes with thresholds:
    
ID # ATTRIBUTE_NAME          FLAG     VALUE WORST BEAT GUY      UPDATE  WHEN_FAILED RAW_VALUE
    
  1 Raw_Read_Error_Rate     0x002f   200   170   051    fail pre  always       -       0
    
  3 Spin_Up_Time            0 x 0027   124   107   021    fail pre  always       -       6800
    
  4 Start_Stop_Count        0 x 0032   055   055   000    Old_age   always       -       45074
    
  5 Reallocated_Sector_Ct   0 x 0033   200   200   140    fail pre  always       -       0
    
  7 Seek_Error_Rate         0x002e   100   253   000    Old_age   always       -       0
    
  9 Power_On_Hours          0 x 0032   052   052   000    Old_age   always       -       35631
    
 10 Spin_Retry_Count        0 x 0032   100   100   000    Old_age   always       -       0
    
 11 Calibration_Retry_Count 0 x 0032   100   100   000    Old_age   always       -       0
    
 12 Power_Cycle_Count       0 x 0032   100   100   000    Old_age   always       -       517
    
192 power-Off_Retract_Count 0 x 0032   200   200   000    Old_age   always       -       229
    
193 Load_Cycle_Count        0 x 0032   180   180   000    Old_age   always       -       61742
    
Temperature_Celsius 194     0x0022   104   089   000    Old_age   always       -       43
    
196 Reallocated_Event_Count 0 x 0032   200   200   000    Old_age   always       -       0
    
197 Current_Pending_Sector  0 x 0032   200   200   000    Old_age   always       -       0
    
198 Offline_Uncorrectable   0 x 0030   200   200   000    Old_age   offline      -       0
    
UDMA_CRC_Error_Count 199    0 x 0032   200   200   000    Old_age   always       -       0
    
200 Multi_Zone_Error_Rate   0 x 0008   200   200   000    Old_age   offline      -       0
    Model family:     Western Digital Caviar Green (AF)
    
Phone model:     WDC WD10EARS-00Y5B1
    
ID # ATTRIBUTE_NAME          FLAG     VALUE WORST BEAT GUY      UPDATE  WHEN_FAILED RAW_VALUE
    
  1 Raw_Read_Error_Rate     0x002f   200   200   051    fail pre  always       -       0
    
  3 Spin_Up_Time            0 x 0027   191   185   021    fail pre  always       -       6441
    
  4 Start_Stop_Count        0 x 0032   094   094   000    Old_age   always       -       6277
    
  5 Reallocated_Sector_Ct   0 x 0033   200   200   140    fail pre  always       -       0
    
  7 Seek_Error_Rate         0x002e   100   253   000    Old_age   always       -       0
    
  9 Power_On_Hours          0 x 0032   062   062   000    Old_age   always       -       28299
    
 10 Spin_Retry_Count        0 x 0032   100   100   000    Old_age   always       -       0
    
 11 Calibration_Retry_Count 0 x 0032   100   100   000    Old_age   always       -       0
    
 12 Power_Cycle_Count       0 x 0032   100   100   000    Old_age   always       -       514
    
192 power-Off_Retract_Count 0 x 0032   200   200   000    Old_age   always       -       351
    
193 Load_Cycle_Count        0 x 0032   038   038   000    Old_age   still       -       487882
    
Temperature_Celsius 194     0x0022   101   098   000    Old_age   always       -       46
    
196 Reallocated_Event_Count 0 x 0032   200   200   000    Old_age   always       -       0
    
197 Current_Pending_Sector  0 x 0032   200   200   000    Old_age   always       -       0
    
198 Offline_Uncorrectable   0 x 0030   200   200   000    Old_age   offline      -       0
    
UDMA_CRC_Error_Count 199    0 x 0032   200   200   000    Old_age   always       -       0
    
200 Multi_Zone_Error_Rate   0 x 0008   200   200   000    Old_age   offline      -       0
    Model family:     Western Digital Black
    
Phone model:     WDC WD1002FAEX-00Y9A0

    ID # ATTRIBUTE_NAME FLAG VALUE WORST BEAT TYPE UPDATED WHEN_FAILED RAW_VALUE
    1 Raw_Read_Error_Rate 200 200 051 fail pre 0x002f always - 21
    3 Spin_Up_Time 0 x 0027 174 171 021 fail pre-4291
    4 Start_Stop_Count 0 0032 100 100 000 Old_age always - x 991
    5 Reallocated_Sector_Ct 0 x 0033 200 200 140 front fail not always - 0
    7 Seek_Error_Rate 0x002e 100 253 000 Old_age always - 0
    9 Power_On_Hours 0 x 0032 065 064 000 Old_age always - 26270
    Spin_Retry_Count 10 0 x 0032 100 100 000 Old_age always - 0
    11 Calibration_Retry_Count 0 x 0032 100 100 000 Old_age always - 0
    12 Power_Cycle_Count 0 x 0032 100 100 000 Old_age always - 507
    192 power-Off_Retract_Count 0032 200 200 000 Old_age always - 0 x 240
    193 Load_Cycle_Count 0 x 0032 200 200 000 Old_age always - 750
    194 Temperature_Celsius 0 x 0022 101 092 000 Old_age always - 46
    196 Reallocated_Event_Count 0 x 0032 200 200 000 Old_age always - 0
    197 Current_Pending_Sector 0 x 0032 200 200 000 Old_age always - 0
    198 Offline_Uncorrectable 0 x 0030 200 200 000 Old_age offline - 0
    199 UDMA_CRC_Error_Count 0 x 0032 200 200 000 Old_age always - 0
    Multi_Zone_Error_Rate 200 0 x 0008 200 200 000 Old_age offline - 0
    Using the drive
    

    File system      1 K-blocks      used available use % mounted on
    
/ dev/md127     1943821568 997890704 944950192  52% / data

    So as you can see I have two green and a WD black drives, trying to decide if its more risky to keep black their or pull on black.

    Let me know team!

    I appreciate the support.

    ShoGinn wrote:

    Now should what player I remove my pool?

    None of the drives having errors, remove the cartridge with the number of very high charge cycle (which is the WD10EARS).

  • How always display the date with taskbar buttons activated in widows 8?

    It's got to be average, just to be there. Even using the buttons small taskbar, it is actually enough space to have always the date and stacked. I would be well with them, next to each other also. I don't really understand why the date masks even as it would fit really well. I'm fine with the help of a third party program if necessary. I already have the classic interface installed because microsoft somehow forgot to add the menu start Windows 8.

    There are several strange suggestions and wonderful here for you to play with.  Make sure that you first create a system restore point.

    Windows 7 - display date using small icons
    http://superuser.com/questions/89628/Windows-7-display-date-using-small-icons

    http://www.Google.com.au/search?q=use+small+taskbar+but+have+date+and+time&SourceID=IE7&RLS=com.Microsoft:-to THE: IE-address & ie = & oe = & gws_rd = cr & redir_esc = & ei = 4L7sUaPiKKWSiQe2_IFQ

  • Pass the disk from ReadyNAS 104 again ReadyNAS 104 #26210568

    I just got a replacement from the ReadyNAS 104 factory. I swapped the drives ensuring that I kept the disc # correct. However, when I start the new NAS he don't know the discs. I need to "turn up the volume. However, I fear that will erase the data. Any suggestions on what to do?

    Hello ckovel,

    When you insert the disc on another chassis that is with the same model, you must insert them all to their respective bays before initializing the NAS. NAS should display disks and volume load.

    If this is not the case, one possible reason is the chassis and the disks do not have the same version of firmware.

    You should still be able to get support for it since it is to install the replacement. It is best that you contact the helpdesk to guide you through it. Use the previous case, it can be reopened and increase if necessary.

    Kind regards

  • How long does it take to extend a volume on a ReadyNAS 104

    Hello

    I have a ReadyNAS 104 that I had started to use with a single disc in it, a red WD 4 TB. However as it was close to capacity I had an another Red WD 4 TB to extend the volume on the.

    It took some time (about 12 hours) for the drive to become ready. To increase the volume and use the two discs, I understand that I had to reboot the ReadyNAS. So I did, but since the display said "restart now. See you soon. »

    Have been led to believe that this will take a while, if someone can give a sign of how long, because it's been 48 hours and I am concerened that something is wrong.

    Currently I'm unable to access the ReadyNAS on the network, obviously I guess as it is still starting, so unable to confirm indeed if he does something.

    Thank you

    It seems awfully long for me, and should be able to see RAIDar.

  • ReadyNAS 104 to 314 #26833764

    Hiya

    I have a readynas 104 with 6 TB drives in there, I want to move to a readynas 314 to be able to use the maximum storage space

    Can I just slide my readers of the 104 in the 314 and not lose my data?

    Thank you

    Looking at your case looks like has already set and the remains to have PHP installed at one time was the problem.

  • EA4500 not find Netgear ReadyNAS 104

    Just bought a Linksys EA4500-NP to replace my Linksys Wireless - G WRT54GL

    Have all the configurations works very well EXCEPT FOR Netgear ReadyNAS 104

    When I turn on the NAS I get boot error "unable to connect the server discovery.

    The WRT54GL assigned IP 192.168.1.10 to the NAS

    The assigned EA5400 IP 10.42.181.142
    Devices of will NOT handshake

    DOES ANYONE HAVE ANY SUGGESTIONS.

    All Linksys Tech Support says "call Netgear.

    Configuration of the network attached as photo

    jaholstein wrote:
    @chadster766: great response.

    then could I also change / force the //server be 192.168.1.10... just in case the other DHCP auto-assigns Protocol thing as 10 on the NAS? If so - would appreciate steps & screenshots. Use a DHCP reservation so the server always gets the same IP address of the DHCP server

    Oh and here I have the NAS or disable during the walk cycle for EA4500 then switch you mentioned earlier? On

    Comments above:

  • Cannot find the driver for trident cyberaladdin graphics (display)

    I can't find the driver for trident cyberaladdin graphics (display).
    The game with the game Warcraft III.
    I downloaded directX 9
    I managed to install the game but I can not play.
    My graphics card is Trident Cyberaladdin T.g.f.o.p. summer HARVEST game producer told me that it is compatible. I tried to find the drivers but I did not find anything effective. On toshiba site there a driver but enough old (preceding the date that I bought the computer...)
    I put (t knox what to do and my son is very disappointed because he can't play with this new game.
    Thanks for your quick response.

    Hello

    As a first step, it would be interesting to know to what operating system your need for this driver? ;)

    Well this Chipset Trident CyberALADDiN-T (called Napa2T) was built in three Types of Toshiba laptops.

    The 6000 Satellite TE2000 and Satellite 6050. (Driverversion all with Version 5.01.2527.0128)

    Normally the drivers that you will find on the Pages of the manufacturer are not the real drivers. Only they are updating the drivers if there are known issues.

    So the only chance for you is to look threw the internet and look if someone else has used this graphics chip and offer are a newer driver than Toshiba.

    Sorry for the response, but I had the same problem with my Machine, but is a more recent revision of driver on another page of manufacturer.

    Good bye

  • Monitoring of ReadyNAS on ReadyNAS 104

    IM using a ReadyNAS 104 and want to use to record the flow of our surveillance cameras. Unfortunately application of monitoring ReadyNAS does not supports more of a camera and recording on motion that makes it completely useless for my application. Is it possible to purchase a license to get a record on motion works on a series of 100 ReadyNAS or is it simply not supported?

    A little off topic, but I finally got the camera to record directly on a ReadyNAS share. All I had to do was setting a quota for such action and finally formatting worked. What the camera calls of formatting are actually create some files binary index and a bunch of zero-byte files hivXXXXX.mp4 which then slowly getting filled with video data.

  • ReadyNAS 104 unable to boot after power failure

    Hello

    My Readynas 104 unit is in a suspended state. Power blue led continues to blink (for hours) when I restarted after a power failure. The disply screen says "READYNAS 6.4.0" and no button works. I can only remove the power cable and connect back to try again to start, but even once, he ends up in the same State of the Power LED flashes continuously.

    Device answering queries ping but actions / iSCSI and admin page not available.

    Someone of you has faced this kind of problem or can help me solve this problem without losing any data please?

    Thank you

    Hussain

    I want to contact support.

  • Different versions of ReadyCloud on ReadyNas 104 6.5.0

    I have two ReadyNAS 104
    Both recently upgraded to 6.5.0

    A while back I accidentally disabled ReadyCloud on the first and then added new - then after that was to connect to the admin Pages using the 'admin' instead of the main user account account. This works even when am so Ok with it.

    Since the upgrade to 6.5.0 - I need to use the account "admin" on both.

    Now, go to the 'Cloud' of these two tab - ReadyCloud option seems to be significantly different on both. Key settings also gived options.

    Not a big issue that I don't use much, but thought I would check why it is.

    Older machine (ReadyCloud disabled + add):

    Parameters:

    New box:

    Parameters:

    Thoughts?

    Clear the cache of your web browser, close your web browser and then reopen the web administration interface. The admin web UI should then display correctly with both systems.

  • I noticed that my user name in the C drive has disappeared and is displayed under the desk

    original title: save files on the net / backup of the files in the C drive

    These 20 to 30 days, I noticed that my user name in the C drive has disappeared and is displayed under the desk. In addition, whenever I try to save a file on the net on my laptop, this allows me to record only at this location:

    C:\Users\vijai\AppData\Local\Microsoft\Windows\Temporary Internet Files\Virtualized\C\Users\vijai\Documents

    Also in the Solution Explorer, while all other folders category, like documents, pictures, music etc appear in the left panel, these do not appear in the right panel. I also note that a "Application Data" folder appeared under my user name and all files stored in this folder only.

    Can someone help me solve this problem

    Hi, VIJAIRAGHAVANP V,.

    You can try the following steps and check.

    Method 1:

    You can try a system restore to a prior restore point before you have been affected by the issue.

    Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

    To run the system restore, you can consult the following link:

    System restore

    http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore

    System Restore: frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

    Method 2:

    If you are still facing problems then try creating a new user account and check if the problem occurs:

    Create a user account

    http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

    If you are not faced with any issue, then check out the following link to correct a damaged account.

    Fix a corrupted user profile:

    http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

    Hope this information helps.

  • HP Recovery Kit will re - install Vista if hard drive has been replaced?

    Hello everyone, this is my first post so I hope that I understand.

    I bought a HP Pavilion s3050uk of second hand compact office, product number RY930AA.

    The only OS on it is a trial version of Windows 7 Ultimate, little time to expire.  I knew when I bought but I was just able to reinstall Vista Home Premium using the HP Recovery Kit and the number of product key from the COA on the PC sticker.

    However, I think now that the HARD drive has been replaced at some point - my machine has a 200 GB (Seagate ST3200822AS ATA) and I think that these machines haven't shipped with a 250 GB?  Now, I'm worried that I will pass on the recovery kit but it won't reinstall Vista because the hardware has been changed.  If it is probably the case of others has experience then I may as well save my money (which is very tight at the moment, where the 2nd hand PC) and put it toward the purchase of an operating system package full.

    Hope someone is able to advise me.

    Thank you

    Stephen

    If you buy a defined recovery disk and perform a factory original operating system image recovery and the partition scheme will be installed on the new hard drive.

    Certificate of authenticity (w\ license key) Microsoft Windows OEM is always visible on the bottom of the laptop?

  • Display data in reverse order.

    Hi everone,

    I'm dispalying two fields in forms 10g to display Arabic and English chracters.
    It will correctly display Arabic and English data, but for some Arab data, he demonstrated in the reverse order.

    How can I solve this?

    my location is
    11.2.0.3.0, charcterset AR8MSWIN1256 Oracle database
    Server of applications Oracle 10 g, NLS_LANG = AR8MSWIN1256
    Order Developer suite 10 g


    Thank you
    Omer

    I got there is character '_' chr (220) in the folder that is not Arabic characters is why oracle does not display data correctly. I have replace the data as replace (Field1, chr39). Chr (220) | Chr (39)) and now it works for me.

  • Can I install Adobe 12 items on my external hard drive? I have all my data there.

    Can I install 12 on my external hard drive and the necessary pieces of program would always settle on the C drive? I have all my data on the hard drive as are all my photos.

    Yes, there are a few pieces that would be installed on your startup disk.

    Personally, I prefer to install app on my machine to an external hard drive and keep the data on the external drive files and access the external drive while working in the elements. However, it is supported.

    Thank you.

    ~ Hermann

Maybe you are looking for