Recovery partition is there but does not start Recovery

Similar Questions

• PC runs, but does not start. Monitor, keyboard and mouse with no signal.

  PC runs, but does not start. Monitor, keyboard and mouse with no signal. Pretty much. And when you want me to remove the battery of the bios, or whatever, it seems tight and hard to get out because it is surrounded by other elements.

  All fans work, the power/battery or anything that works I think that, since there is a fan on the right where it is and it seems to work. I remember what happens before, I don't know, but before that, there are many gels. This error below was made before all this happened, but I managed to run f8 and then run normally until it freezes again. Then, after that, it runs but does not start. No beeps etc. The best fans will have plenty of vouches and Bravo to wherever you like me to vouch or maybe send the great service that you provide to administrators if that's even possible, haha.

  Thanks in advance.

  "

  The file is possibly corrupted. The file header checksum does not match the checksum calculated. »

  It is a sign of a lack of food.  Looks like you have a desktop computer?

  Power supplies run about $50.  It is a rectangular box at the corner of the system in which the power supply will from the outside.  It's a pretty standard form in most of the PC and with a little investigation thorough replacements can be found.

  It is usually held in place by 4 screws and can be held in place with a spring clip.

  Most essential, is that you need to buy a replacement with the right number of straight plug forms to adapt to your PC.

  This seems more complicated than it really is and takes about 5 to 10 minutes to do the replacement.

  Look at the power output of the power supply failure and buy a new, more powerful.  New desktop PC usually come usually with a diet under size and what are the causes these failures is too strong a request for devices you have connected.  So, buy one with a higher power rating.  Usually about 500 Watts does the trick.

  If you do not feel upwards to this task, a technician should not charge you much like this.

• Put 8g memory in es1-512 but does not start. Had to put 4g in. Does anyone else have this problem?

  Put 8g memory in ES1-512 but does not start. Card say that it will accept up to 8 GB. He went out, re he sat several times without success. Does anyone else have this problem? Thanks in advance.

  Hello

  Here's the original memory stick for Aspire ES1-512:

  KN.8GB07.013

  SODIMM.8GB.DDR3L - 1600.KINGSTON

  OR

  Compatible memory: Kingston

• access to the content of the files downloaded from the internet: when I download PDFs from the internet to my documents, they get there but does not open

  When I download PDFs from the internet to my documents, they get there but does not open.

  Download Adobe Reader; Uncheck the box first the Google toolbar:

  http://get.Adobe.com/reader/

  How to set file Associations:

  http://articles.TechRepublic.com.com/5100-10878_11-6172036.html

  How do I... Change file extension associations in Windows Vista?

  See you soon.

  Mick Murphy - Microsoft partner

• MacBook Pro-life extendable start-up chime, but does not start

  I have a start 2011 15 "MBPro8, 2

  Quad Core Intel Core i7

  2.30 GHz

  Boot ROM version: MBP81.88Z.0047.B2A.1506082204

  Intel HD Graphics 3000 VRAM:512 MB

  AMD Radeon HD 6750M VRAM:1 GB

  8 GB of RAM 1333 MHz DIMM0

  It will not start.  Trying to start the machine, it enters a loop-

  1. startup chime

  2. grey screen with Apple

  3. the small wheel starts to turn under the Apple

  4. the screen goes black

  ... and the cycle starts over.

  The computer does not start in Mode safe.  In an attempt to safe mode the loop above has the addition:

  3. a progress bar is displayed but does not progress.

  I have reset the PRAM

  It will start up in target Mode, so I was able to recover data

  In target Mode, I was able to run first aid utility on the drive.  This has not fixed the problem.

  I can hold down the Option key and see Macintosh HD and the recovery Partition.  If I try to boot from the recovery partition, I get the same loop.

  I can start in the Test of online material, which revealed no material problems

  I can boot in Verbose mode and it always happens in the same place

  Execution fsck_hfs (version 226.1.1 of hfs)

  BootCacheControl: cannot open /var/db/BootCache.playlist: 2 no such file or directory

  ' ' It would be possible for me to insert the "var/db/BootCache.playlist" file using target disk mode?

  Other thoughts?

  Have you tried resetting the SMC?

  Reset the management system (SCM) controller on your Mac - Apple Support

• Touchsmarrt Tx2 turns on but does not start.

  The laptop turns on I hear the fan, the caps lock and a lock of numbers blink, but it does not start. I'm runnin windows 7

  Home premium. I did recent changes. Just put computer in mode 'sleep' and he won't wake up. The wireless light is orange.

  Electrical components sometimes must have all the food sources removed and reintroduced to work properly.  Try to perform a hard reset first, if this does not work then we will move on to the next step.

  To perform a hard reset

  • Shut down the computer by going to the menu start and select shut down. (If you have no display, hold the button for 5 seconds); (if the computer don't market, go to the next step)
  • Unplug the adapter from the laptop.
  • Remove the battery from the bottom of the laptop.  There will be a switch/battery eject button.
  • Wait at least 1 minute with all sources of power disconnected.
  • Reinsert the battery and reconnect the power adapter, and then try to turn on the laptop.

• Satellite A300 - rotates but does not start

  Hello

  I have a Satellite A300. I had several probems for the boot since 2 months ago: when I want to turn on my laptop, it turns on but the screen keeps black and it does not load the screen "Toshiba Leading Innovation". 'Satellite' (to the left of the mouse) light is on (it would go only about a second then to start and then turn off) and it will turn off.

  I try again for so many times with all the possibilities: without battery, only with the power adapter, two, but it does not start. I don't know what I can do. I always Hibernate my laptop because I'm afraid of can not start it the next day.

  Could you help me? If she cares: I had to buy a new battery (not original from Toshiba) because I had to change the original. No more changes to my laptop.

  Thank you very much and sorry for my English written: S

  Diego

  Hey Buddy,

  > I had to buy a new battery (not original from Toshiba) because I had to change the original. No more changes to my laptop.
  Of course, it s always advisable using Toshiba original spare parts only, but if you notice the same problem with AC adapter only it s not related to the new battery.

  Just to make a better diagnosis: If you have connected an external monitor? The internal display is perhaps the problem and doesn't turn on and it would be useful if you are testing the situation and an external monitor.

  But this noise as a hardware problem serious and in this case, you can wait to contact an authorized service provider. Technicians professional diagnostic tools to make an accurate diagnosis and to Exchange defective equipment parts.

• Pavilion 15 - p002nia: HP Pavilion 15 - p002nia fan runs but does not start

  My 2 year old son poured drink chocolate on the keyboard of my laptop 15 - HP Pavilion p002nia recently bought. When I found out, the laptop had stop, all efforts to start failed. White LED light on the button walk / stop would stay and fan would run for 30 seconds, stops, starts and stops continuously. The system does not start. What can I do? The jury is dead?

  Hi TheOldMan, thanks for your response. But, someone suggested I have dismantle the system, clean with alcohol and dry that it might help the dos system.

• 15-p151nr Pavilion: Pavilion 15-p151nr dead, power supply LED flashes 3 times but does not start

  With or without the adapter is connected to the computer (well known socket), the computer will not turn on.  The LED located on the left side of the computer where the socket is attached blinks 3 times (white), but does not supply power to the top.  Another post I saw said "continuous" flashing would be the power adapter, but wanted to ensure that it is in fact the problem before buying a new...  Any help would be great!

  Hi @joshuaj21,

  Welcome to the HP Forum!

  It's a great place to find answers and advice! You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums: first time here? Learn how to publish and more

  I understand that the computer will not turn on. However, when you connect the AC adapter of the power port light flashes 3 times.  Please check that the power cord is not one of the recall. HP laptop AC Power Cord Safety retirement program and replacement announced August 26, 2014 .  You use a power bar?  Have you tried a different outlet? Here is a link to the HP laptops - tests and using the AC adapter which can also help.

  Please let me know the results.

  Thank you! If it helps you to find a solution, please click the button "accept as Solution"down below in this message. "If you want to say 'Thank you' to my effort to help, click on the" ""Twww.Mountainview.rsb.qc.ca Up ' give me a Kudos. : catvery-happy

• Created recovery disc is ok, but does not start Satellite A300

  Hello
  as the title suggests, the disks fail to start, details below formatted for reading easier (I hope :))

  -All-new series Toshiba A300
  -J' have created a disk of restoration with the toshiba utility, there was no error, the files are there but the drive seems to be unbootable.
  -This happens with both attempts, I made, using Verbatim r and Sony + R media.
  -The recovery disks will NOT start on my desktop system either.
  -L' laptop starts fine with a couple of distributions Linux on CD - R.
  -J' use F12 to tell the laptop to boot from the DVD.
  -J' have much experience dealing with the LiveCD, bootable disc burning, etc., so I'm inclined to think there is a problem with the toshiba utility.

  Any help will be much appreciated. Thanks in advance.

  Hello

  There is certainly nothing wrong with the Toshiba Recovery Disk Creator.
  I burned the recovery disc too. Once it failed because I did not use fully compatible DVD. Then I tested it with TDK - R and everything went well.
  No errors, nothing. Finally, I booted from the DVD and could reinstall the OS too.

  I presume that you should check the other DVD.

  Good bye

• After the upgrade "My recent documents" on the Menu start is still there but does not work.

  Original title: upgrade to IE8 problem

  Windows XP Pro SP3 System.

  Recently updated to the latest version of IE8 - after Upgradeing "My recent documents" on the Start Menu is still there but notworking.

  Have already checked the settings are fine and recent documents demonstrate in applications Office OK.

  MSTech notified support registry check I have for you ensure that value to start showing RecentDocs has the value 2 (Enabled), it is.

  Anyone can shed light on this issue? all answers gratefully received

  First, there has been no recent updates for IE. There were two updates of security for XP this past

  On 12 July.

  Microsoft Security Bulletin Summary for July 2011
  http://www.Microsoft.com/technet/security/bulletin/MS11-Jul.mspx

  The latest updates for IE (KB2544521 & KB2530548) realize the June 14,2011.

  Microsoft Security Bulletin Summary for June 2011
  http://www.Microsoft.com/technet/security/bulletin/MS11-Jun.mspx

  Being a user of Microsoft Security Essentials , I wouldn't know of the latest updates for Norton but I am aware that some antivirus programs may cause this problem soyou might consider a posibility.

  In fact I think that Imran M may have been on the right of remember suggesting someform has corruption. Nothing will do it easier than the registry cleaners because I see that you have two-Registry Mechanic and WiseFixer.

  See the following topics:

  Should I use a registry cleaner
  http://aumha.NET/viewtopic.php?t=28099

  RegistryJunk: A Windows fact of life
  http://blogs.technet.com/b/markrussinovich/Archive/2005/10/02/registry-junk-a-Windows-fact-of-life.aspx

  Why I don't use Registry cleaners
  http://www.edbott.com/weblog/2005/04/why-i-Don ' t-use - Registry cleaners.

  Demystifying the Windows registry
  http://www.bleepingcomputer.com/tutorials/tutorial74.html

  You may be lucky enough that you would have only to reset the permissions for the recent Documents.

  How to capture a file or a folder in Windows XP
  http://support.Microsoft.com/kb/308421/en-us

  And then there is no way to assess the damage, to use Registry cleaners. I HAV come across situations where the permissions would be reset, which is best left to the Microsoft Support using the remote connection. I've also seen cases requiring a full reinstall of the operating system. Personally, I would rather deal with malware infections.

  If you feel that it was an update issue, you must open a pension case. Start here - https://consumersecuritysupport.microsoft.com/

  In addition, Microsoft now offers free, online (third party) support for issues such as:

  Windows Update
  http://supportservices.Microsoft.com/support/services/windows_update

  I hope this helps.

• Pavilion dv7-6101eo works but does not start.

  My laptop got a cup of black coffee on the keyboard.

  I have cleaned up a bit, disassemble the entire laptop, same cpu, added new money and put the brand new togeather. Started and everything worked. Close the computer laptop domw - dead. Could not start without flashing, nothing. Repeated picking hand everythung once again and began. Works perfekt press start and go. So this time I made a recovery and reinstalled everything.
  
  The keyboard does not everywhere, a, s, d, f, e, l and Swedish letter o does not work very well. I don't have much contact for helmet properly not work either - you get a bit of his, but a little in the speakers and phones. I forgot to check the sd card reader, but here, it is located in the corner of a speaker.
  
  Onece I disassembled except mobo and this card reader and then the laptop is not started. I had to do it all again and he began. So now I'm a little confused to what it can be?
  
  It does not remove batteri, pushing start button. Not 15 seconds - not even 2 minutes. I know that battery, power cord works fine, cd, network, hard drive, memory, fan, cpu - everything works and yesterday the laptop running 24 hours without dysfunction at all. Programs installed and revived over and over again. And after all that I closed the laptop the way you should. And - he won't do it again?
  
  There is a possibility that some power is left in the drive cd-card or something that stops the laptop to boot? Or is it enough that the keyboard is malfunctioning? I don't understand what it is with the disassembeling process that makes the laptop to start.
  
  It's not fun to have all take part whenever you want to start your computor ...

  Looks like the coffee did more damage as you thought.

  You should have dismantled it and used contact cleaner everywhere where coffee could go.

  The next step is difficult for most people: allow to dry for at least a day outdoors in a dry place without danger... It is unfortunate that you don't have that.

  Consider looking for a replacement book.  A motherboard and keyboard options, less the cost puts you upside down against the current value of the laptop.

• After installing antimalware doctor, tried to restart, but does not start...

  .. .He is as file system of the disk is not recognized never gets to a point where I can enter in F8 safe mode. The drive is recognized in the BIOS and diagnosis Seatools says its OK. Use a LiveCD of ubuntu, I can access the drive and see the file system. Tries to start on a Windows XP CD to the recovery console to run chkdsk, fixboot, fixmbr etc., says it cannot detect a hard drive. Can anyone help?

  Certainly, you have a SATA hard drive.  The original Windows XP CD does not include a driver for the SATA drives (Ubuntu and the BIOS most recent do).  When you boot from your Windows XP CD, you will probably come to a point where it asks you to press F6 to install additional drivers.  Here's where you need to press F6 and then install a floppy with the SATA drivers on them.  If you do not have a floppy drive, things get complicated, you may need to create a XP CD slipstreamed with the pre-installed drivers.  You can probably find the SATA drivers from the Web site of the manufacturer of your computer or the drive manufacturer's Web site.

  "Limited OEM driver support is available with F6 during installation of Windows XP and Windows Server 2003"
   <>http://support.Microsoft.com/kb/314859/ >

  If I were you at this point, I would be your drive Ubuntu allows you to save your data from hard drive on a USB drive or a network drive, and then reinstall Windows.  You can probably press a combination of keys very early in the boot process before the Windows startup that will render your machine on the condition that bought from a recovery hard disk partition.  This is a radical step, but you might find it faster to attempt recovery.  Check the Web site of the manufacturer of your computer for a user manual for your computer that describes how to do this.

  HTH,
  JW

• Satellite A500-148 turns on but does not start

  Hi all, I have a Satellite A500-148 from a friend who asked me to take a peek, it turns on, but does boot when I press the following power button occurs:
  -The power button and the charger are on and the hdd led only flashes once
  -The fan comes on for about 3 seconds
  -No image on the screen, I indicated a light against it, but there is really no image

  Tried to reset by pressing the button for 30 seconds without the changer is plugged.

  I disassembled it and noticed that this laptop has an external video card, so my question is, who's broken the video card or the motherboard.

  Thank you

  To be honest I don't understand this with an external video card. Can you describe how you mean exactly?
  In any case, on this virtual path, it is not easy to offer the exact diagnosis. You can try the little test and remove this external adapter, RAM and HARD disk, and try to start again.

  Ask your friend if he had something that may be responsible for this.

  One last thing: laptop stays in r might have turned off after a certain time?

• How to install Ubuntu for PowerEdge 1850 - updated: installed, but does not start?

  I recently got a used PowerEdge 1850 (BIOS A04 version) without OS, with plans to install Ubuntu Server. I read that you can boot from a flash drive USB for it, so I used a tool to make a 8 GB USB 2.0 flash drive bootable for installing the operating system. I put USB drive on auto emulation and the USB controller on with BIOS support. In the order of start, emulated floppy USB drive has been updated with the top priority. The flash player has been connected to the USB port right front, with a keyboard at the front left, if it matters.

  When I turn it on with this set all when it reaches the last line ("press CTRL-E to enter the BMC configuration within 5 seconds," without any player flash it just says only: "boot device available" at this stage "), it does nothing. Just on a blank line, no error or anything. I know that it did not freeze because underscore flashing. By pressing a button any will result in a single beep, same F2 to enter the BIOS setup.

  There are 73 GB HARD drive at location 0 (left), nothing in the Slot 1 (right) and 4 GB of RAM. No material inside has changed.

  Anyone know what I am doing wrong? If I just have something wrong set, can you give me instructions step by step from scratch (that is, a blank flash drive/CD and ISO downloaded), or at least point me in the right direction to correctly set up the flash player if it is the problem?

  EDIT: All right. Ignore my next post in the thread. I'll post if no new complication.

  Roadsguy

  It still hangs on the last line in the commissioning after the line 'Press CTRL-E to installation of BMC', with the blinking underscore, so I know that it is not frozen.

  It is bootable media and try to boot from it. It seems that the bootstrapper does not initialize correctly. I would suggest reformatting and reinstallation of the operating system again. The question is not hardware related. You can try another version of Ubuntu.

  Thank you