recovery system configuration will not work on PC

Similar Questions

• I have XP and had a virus. I removed the virus, but now the system restore will not work. I tried Safe Mode but clings to the confirm restore point selection. Help

  System Restore will not work

  Hi FriendFriend,

  1. did you of recent changes on the computer?

  2. do you have security software installed on the computer?

  3. you receive an error message when running the system restore?

  I suggest that you put the computer in a clean boot state, and then try to clean boot.

  It is possible that some third-party programs installed on the computer is causing the problem.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  If the previous step fails, then view the event logs to examine the system restore service errors.

  (a) click Start, click run, type eventvwr.msc/s in the Open box, and then press ENTER.

  (b) click on the category System .

  (c) click the Source tab to sort by name, and then look for "sr" or "srservice." Double-click each of these services and then evaluate the event description for any indication of the cause of the problem.

  Steps of troubleshooting for problems when you try to use the System Restore tool in Windows XP

  http://support.Microsoft.com/kb/302796

  Procedure to view and manage event logs in Event Viewer in Windows XP

  http://support.Microsoft.com/kb/308427

• All my .exe files have been removed. as well as system32\rundll32.exe... How can they be retrieved when no file opens and the system restore will not work.

  Original title:. Nothing works.

  All my .exe files have been removed. as well as system32\rundll32.exe... How can they be retrieved when no file opens and the system restore will not work. I can't install a fixit program or run anything at all.

  Safe mode?

  Looks like you have a virus/trojan/worm infection pretty good...

  Actually, even if you get executables run again - you can be (read as "will be") better off the coast of a new facility.  Wipe and install media with your product key and other serial numbers and installation for other products media you own and restore your last recognized reliable backup for your files.

• Windows 7 does not start; Startup Repair won't work; Know last good configuration will not work

  Windows 7 64 bit machine. Automatic Windows updates were installed during the night; has started acting strangely this afternoon.  After an attempt to re-start, got the "Windows Error Recovery" screen with the "Windows did not start. A recent message HW or SW change might be the cause".  When I try to 'Launch Startup Repair' a screen returns but just hangs.  When I try to "Start Windows normally", it brings back me to the Windows error recovery screen.  When I hit f8 for when you start to get the screen "Advanced Boot Options" and try to go into secure Mode or use the last good known Configuration option, each one brings back me to the Windows error recovery screen.

  Any ideas on how to get this resolved?  Thank you!!!

  Hello

  The problem is since it will not run the startup from the Windows 7 disc repair you then you
  need some kind of support, and the cause is likely to be material. A Dell thing you want to do
  is to restore the system back to the factory plug 'IF' possible so it would be a good idea to save the
  data before calling their (possible an another 'IF'). Try to put the hard drive in another computer
  as the 2nd disc (best method) or in an external case USB (less likely to work) and then copy
  data on removable media such as CD, DVD or other external USB drives.

  Good idea to check with the technical support Dell, their online documentation and the Dell forums where he
  perhaps others with the same problem.

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/
  Other choices would be a real store of the computer performing the internal repairs (not the leeks and the glances at one
  Best Buy or other stores). Of course if she has any warranty Dell is the best choice, and
  can be in effect regardless of any warranty.

  I hope this helps.

  Rob Brown - Microsoft MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Hardware configuration will not work under Windows 8

  Hello guys,.
  I'm here because I can't get the hardware configuration (v. 1.63.1.34C) working with Windows 8.
  I would like to know if there is a recent version more or a way to get the program to work.
  I can install it, yet when I open it, it just won't do a thing.
  I use a Toshiba Satellite P755.

  Thanks to anyone who can help!

  Post edited by: rfscouto

  Thanks for the last comment. All you can try right now is to use the stuff offered for the newer models, but I imagine that this will not help a lot.

  I'm afraid it takes a bit of m.

• XP pro have two problems: the system restore will not work and rdpclip seems to work computer

  I had a virus, trogan, stopzilla online to fix the problem after allowing access to my computer, (it's a virus) tried to uninstall this program, finally just disabled and removed from the start menu.

  Now, in the pc Registry mechanic tool the first thing listed is rdpclip as run from my computer.
  Since that time I have been unable to use system restore from windows system.   only restore I access is
  from backups of registry mechanic even if I went and set on system restore after that I checked the settings and discovered that they had been handed over to OFF.
  I used the restore before so I know it worked before the access help online.

  Is the solution just to disable repclip?   I have access to my computer so that I have to allow access by external connection...
  computer programs run more slowly, there is always time to wait before the update when I try to use wp-admin to make changes on my Web site.

  Former title changed, but explains the problem
  XP pro, has had a problem with virus removal program, it turned off because it wouldn't uninstall.  Now when I run Registry mechanic it shows my system being run by rdclip.  I can't use the windows system restore.  Points on the calendar are lit up but do not work.  Can I use mechanic registry to disable the rdclip? in auto start menu?  If so this might restore ability to use the system restore?

  Hello

   
  1. you receive an error message when running the system restore?
  2. which antivirus app do you use?
  3. what happened when you try to uninstall the program?

  4, are service packs installed on your computer?

   

  To uninstall the application:

  Method 1:

  Run the hotfix, restart the computer and try to uninstall

  Problems with programs that cannot be installed or uninstalled.

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall

   

  Method 2:

  I suggest to keep the computer in a clean boot state and check the status of the issue.

  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353
  Note: After you have used the boot is a way to solve your problem, you can follow these steps to configure Windows XP to start normally.

  I also suggest that you scan your computer with the Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malicious software.

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.
  
  http://www.Microsoft.com/security/scanner/en-us/default.aspx
  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.
  Important: While perform analysis on the hard drive if bad sectors are found on the hard drive when parsing tent repair this sector if all available on which data may be lost
   
  To solve the problem of system restore:
  I would sugggest you to go through the link following.
  Steps of troubleshooting for problems when you try to use the System Restore tool in Windows XP.

  http://support.Microsoft.com/kb/302796

   

• 1 t verbatim USB stick not recognized by the system and will not work

  I used my USB from Verbatim 1 t hard drive in the past and it still works on my Vista computer, but know is is a USB 'unrecognized' device and does not work on my XP.  In the system hardware listing is visible, but there is no driver for it and not available from my computer.  This disc is missing?  How can I get this, my backup disk, of the function?

  Hello

  Try the steps of troubleshooting mentioned in the links below and check if the problem persists.

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  Note:

  BIOS change / additional settings CMOS (semiconductor) to oxide of metal bad cancause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Why my computer does not detect my new USB device when I run Windows XP or Windows Server 2003?

  http://support.Microsoft.com/kb/314634

  Note:

  Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://support.Microsoft.com/kb/322756

  How to back up and restore the registry in Windows

• System Restore will not work, said that there is an error and try a different restore point

  When I try to use the system restore it always fails, it says there is an error and try a different restore point, I did several times and it still does not work, can you help me. Thank you

  Hello

  This can help you:

  1. If you are using Norton, you should disable Norton inviolable Protection before using the system restore.

  http://Service1.Symantec.com/support/sharedtech.nsf/pfdocs/2005113009323013

  2. try to use Safe Mode system restore.

  http://bertk.MVPs.org/html/restoresysv.html

  3 Malware will stop at the system restore.

  Download, install, update and scan your system with the free version of Malwarebytes AntiMalware, if necessary in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  And here's how to go in Safe Mode options; Select safe mode with networking from the list of options:

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  See you soon.

• Why the system restore will not work correctly?

  When I run the system restore I get message saying that it did not work properly and system has not been restored at that earlier time. This has happened several times now.

  Hello

  If you use Norton which will cause problems with the restoration of the system; clear all by doing the system restore.

  You would like to try to make the system Safe Mode restore, because that will often fix the problem:

  http://bertk.MVPs.org/html/safemodevista.html

  Use the arrow keys to move to the top or to the bottom of the list of Options > use then ENTER key to select Mode without failure.

  See you soon.

• AOL system information will not work

  XPRT.dll does not work on aol 9.6 information system.

  Then contact AOL support.

• I lost the office and all programs-system restore will not work. Now, all I have is a blue screen.

  Original title: I lost the office and all programs-system restore won't work

  I don't know what happened, now all I have is a blue screen, if I click on programs it says 'empty' can not get on anything

  Hello
   
  1. what exactly happens when you try to perform the system restore? If you receive an error message then, send the same return.
  2 have you made changes on the computer before this problem?
   
  Please answer these questions and to provide more specific information on the issue. This could help us help you better.
  The following articles could be useful.
  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen
  http://support.Microsoft.com/kb/318027
  When you point to "Programs" on a Windows XP-based computer, the program list does not appear, or the list of programs is empty
  http://support.Microsoft.com/kb/941248

• Okay, so my problem is that Disk Defragmenter, disk checking and the system restore will not work.

  I tried to go to the c drive and right on it and going click Tools then error checking, but it did not work. I tried dfrg.in and right click to install. I tried to use cmd fixes, I found on the net. I tried a lot of bugs, but nothing helped. Any ideas? Thanks for your time. Here are some links with difficulties, I've tried. I don't know he said that my c drive is dirty my c drive is mt RAW disk fnctions used due to the command chkdsk/f.

  http://www.theeldergeek.com/forum/index.php?showtopic=28251
  http://www.andreasroom.com/blog/archive/2004/01/18/Defrag.aspx

  xador,
  If you start the command prompt and run Chkdsk/r you get an error right then or after restart and tries the kick-off of the check?  What is the error message you get?  You have all the maintenance of the system or registry cleaner program installed or running?  You have your running antivirus software?

  Let us know. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• System Restore will not work for any date and computer says that it is running in auto mode.

  I have a 30 GB master and slave of 160 GB. 26/03/11 I copied a large file of 11 GB of the master to the slave because I received alerts that the disc was or almost. After you have copied from C to D, I deleted the C file and the missing file of the two drives. I tried to use the restore of the system without result. No matter what I do "Unsuccessful System Recovery" is the only message I get. Is it possible to recover a file that took me hours to compile it?

  This looks like a self-inflicted wound / pilot error.

  Deleting files in the Recycle Bin does not release disk space.  When you delete things in the trash, all you really do behind the scenes moves the items from one folder to another folder (the folder to the Recycle Bin).  They always take place until you clear items from the trash.

  System Restore won't help you recover personal files anyway - this isn't what he does.  SR cares your personal files.

  A backup will help recovery of personal files.

  I think it's against the rules for people at Microsoft to suggest or sometimes even to read all the information of any URL Internet that does not begin with microsoft.com, where the previous warning about third party programs.

  However, I think that to get off the beaten track (as they say).

  This is a popular program of third party who sometimes helps to recover accidentally deleted files:

  http://www.Piriform.com/Recuva

  It may be too late for your files, but I would also check the configuration of your trash if you have several volumes of hard drive from your symptoms question do not quite add up correctly.

  Even if SR would not help in this case, your SR expected still works what is another potential problem to solve.

  Now I'm folding stock and return things to the technical support engineers.

• System Restore will not work XP

  Process looks ok, but the final message is unable to restore Windows... Got that 4 times

  Okee-doke!

  After you run a complete analysis with MBAM, if you decide to continue using it, MBAM said they can catch 99.9% afflictions he knows with the quick scan and it won't take so long.  I'd like to just run at least a full analysis first, then you can pass just the quick scan and just run full time or if you are suspicious of a problem.

  SAS will usually find just a bunch of tracking cookies, but sometimes finds other things.
   
  Don't forget to update the definitions before running either - MBAM with new definitions sometimes happens several times a day as new threats are discovered.

  If you continue to suffer from poor performance, we get some clarification on your system to see if we can understand it, so if you care to continue allowing angle we know.

  Your system will work generally always better after a fresh install... for a while, but I have not reinstalled my XP on a system I have to 7.5 years and it works fine - I just fix them when he needs Fixin '.

• My system is continuously restarting and willingness to complete start only in safe mode. System Restore will not work even through DOS command. What to do next?

  Running Vista SP2 64 bit on a Dell Inspiron 530.  System will come up to the login window, if there is no connection - will restart on its own, repeatedly.  It will allow me to log in, but as soon as I get on the desktop, in a short period of time, it will restart.

  I am able to connect through safe mode and safe mode with networking mode.  I tried the system restore by selecting many different restore points using rstrui.exe / offline: C:\windows command safe mode.  The operating system is running on the C drive.  Status on C «Ready to restore» watch

  He always enough immediately cause the error:

  System restore failed... System restore failed due to an unspecified error.  The parameter is incorrect.  (0 x 80070057)

  I did not knowingly install something again before that happens.

  What to do next?

  Hello

  Here's how to use the system without a command restore.

  http://bertk.MVPs.org/html/restoresysv.html

  And information of Dell.

  How ro reinstall from the Dell recovery partition:

  http://www.Dell.com/support/troubleshooting/us/en/04/KCS/KcsArticles/ArticleView?c=us&l=en&s=BSD&docid=DSN_336966

  Reinstalling the printer Dell supplied disk:

  http://www.Dell.com/support/troubleshooting/us/en/19/KCS/KcsArticles/ArticleView?c=us&l=en&s=DHS&docid=DSN_339949

  Reference Dell troubleshooting with startup problems:

  http://www.Dell.com/support/troubleshooting/us/en/19/KCS/KcsArticles/ArticleView?c=us&l=en&s=DHS&docid=DSN_343119

  Run the built-in diagnostic software:

  http://www.Dell.com/support/troubleshooting/us/en/04/KCS/KcsArticles/ArticleView?c=us&l=en&s=BSD&docid=266787

  And if this does not resolve your problem, please contact Dell or their Support Forums:

  http://en.community.Dell.com/support-forums/default.aspx

  See you soon.