Recreate the image MARCH issue 20

Similar Questions

• 210 mobile G1: how to recreate the image on a laptop with Windows 7 210 installed on the device

  Hello

  I try to put an image that has been created in the image of fog service 1.2 and am having problems starting the fog in ipxe. I tried to update the chip set drivers and the network drivers with no luck. When you start first in ipxe, the machine acts like it wants to register the machine, but then it just keeps restarting. I can never get fog gui so that I can recreate the image on the machine. Any suggestions on what I need to do to make this work. I have 30 laptops to recreate the image.

  Thank you in advance,

  Angie

  Step 1: Copy the Source files to the PXE server

  In this step, you copy Windows PE source files to your PXE server.

  1. On your computer, click Start, point to programs, point to Microsoft Windows OPK or Windows AIK, and then click Windows PE tools command prompt.
     The menu shortcut opens a command prompt window and automatically sets environment variables to point to all the necessary tools. By default, all tools are installed in C:\Program Files\\Tools, where can be Windows OPK or Windows AIK.
  2. Run the Copype.cmd script. The script requires two arguments: architecture and destination location of the hardware store.
      

• replaceable hard disk on almost identical machine or recreate the image?

  I have an old Dell Latitude D830, which seems to have a dead motherboard.

  Its backed up and photographed using Windows Image in Win 7 Ultimate.

  Search on ebay for an identical machine so that I can just swap the HARD drive or recreating the image.

  Those that I find is built within months of the mine, but have slightly improved processors.

  Mine has a core 2 duo t7250 and some that seem to be good have the same thing with a t7500.

  He screw it all or if it's similar enough for a HARD drive swap might work.

  If this isn't the case, a HARD swap disc then a new image perhaps?

  IF I bought a replacement motherboard would only be re-inage?

  Thanks for the help.

  As long as the Windows 7 Ultimate FULL retail sales license, you can transfer; read this part of my answer.

  If this is an upgrade license, you can transfer it to another computer, but you need an operating system that is installed to upgrade.

  When you move a BONE on another machine, clean install is the recommendation

• sensor to recreate the image via the service account?

  Hello, I have the following problem with a JOINT-2 (4.1.5 S211) module:

  I am able to get to the screen to login via SSH. I connect with my login and my password but the following error: cannot communicate with authenticationApp (getUserAccountConfig). Please contact your system administrator.

  You want to run cidDump? [No]: _

  I can, however, enter into the sensor via the service account. I tried to stop and restart the CID as well as restart the sensor, unfortunately without success. At this point, the only thing I know to do is run partition recovery for reimage the sensor - is it possible to do it on the service account?

  -Patrick

  Hello

  You use the set of user name and password? What happened to the sensor through telnet and HTTPS access? Are you facing the same problem with above all?

  If the password is correct then the engine of Authantication could have been corrupted.

  You can rebuild image of the sensor through the service account.

  Start the JOINT-2 to the maintenance partition:

  cat6k # hw - module module reset cf:1 module_number

  Session in the partition maintenance CLI:

  processor cat6k # session slot slot_number 1

  Connect to the partition maintenance CLI:

  Login: guest

  Password: cisco

  If it is possible, then you can recreate the application partition image:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/csids/csids10/hwguide/hwclipr.htm#wp91045

  After you re-create the image restart us the JOINT-2 for the application partition:

  cat6k # hw - module module reset hdd:1 module_number

  Check that the JOINT-2 is online and that the version of the software is correct and that the status is ok:

  cat6k # see the module_number module

  Connect to the JOINT-2 application partition:

  processor cat6k # session slot slot_number 1

  You have to retrieve your backup configuration.

  Note the post if it helps.

  Ashish

• Recreate the Image sensor 4235FE problem

  I can't connect to the device ID using SSH and account netrangr and su more late-root. But although I had the sign #, when I run the terminal command configures, he returned with a configuration not found message.

  Here's a screenshot...

  Last login: kills Jun 1 18:22:03 2004, by 10.31.166.30

  Sun Microsystems Inc. SunOS 5.8 generic February 2000

  Sun Microsystems Inc. SunOS 5.8 generic February 2000

  You have logged out of the 10 using vt100

  using DISPLAY = 10:0

  [email protected] / * /-inside: / usr/nr

  > su-root

  Password:

  Sun Microsystems Inc. SunOS 5.8 generic February 2000

  # configure terminal

  Configure: not found

  #

  I checked my working directory is the root. See below

  # pwd

  / root

  # ls - al

  Total 25490

  -rw - r - r - 1 root other 7784 11 May 15:01 - r

  drwxr-xr-x 4 root other 512 11 May 15:10.

  drwxr-xr-x 21 root root 512 20 May 16:03...

  drwx - 2 root root 512 .ssh December 6, 2001

  -rw - r - r - 1 root other 69680 r 11 May 15:00

  drwxr-xr-x 2 root other 512 tmp December 3, 2003

  Note that when I'm in the root, the cursor reads that #, it does not read XYX # where XYZ is the name of the sensor. Does this mean something? This is why I am unable to make the terminal command configures. The device also does NOT recognize the command configures the sensor either.

  What directory I was in before I can issue the terminal command configures. I connect remotely using ssh. The device's ID NetRanger 4235FE.

  Personally, I would get a free exchange on your old 4230-FE for a new 4235-FE. There is a bulletin for 4230-FE sensors that indicates that they are subject to a motherboard failure. Cisco to exchange your old 4230-FE for a current 4235-FE. Follow this link: (http://www.cisco.com/en/US/products/hw/vpndevc/ps4077/products_field_notice09186a00801850de.shtml) and fill out the form. I traded my sensors 8 and got the last expedition just 2 weeks after submitting the paperwork. I find this very much, since the 4230's are anyway end of sale.

  Now, the answers to your questions:

  (1) the CD upgrade you received must be Version 4. (1) S47, this is your starting point.

  (2) to install the image on the sensor, that you should just hang a keyboard and the sensor screen, insert the upgrade CD and allow it to start. The installation process is very intuitive. After installation, the sensor will reboot. You can connect the sensor freshly installed with the name of user and password cisco/cisco.

  (3) see #2 above

  (4) the command and control interface is the port through which the sensor can be controlled and the interface through which it makes alarms to external sources. After the basic installation, you can connect to this interface with a cord connection (crossover) or via a switch (straight through) and use IDM (GUI of the probe).

  (5) see responses to the tightening of the bolts 2 and 4 above.

  2nd n ° 5) the 4230-FE and 4235-FE have all two CD players.

  (6) this is a good starting point for more information about the Cisco IDS sensors (http://www.cisco.com/pcgi-bin/Support/browse/psp_view.pl?p=Software:Cisco_IDS_Sensor_Software)

  I hope this helps.

  Don

• Need to recreate the image tool for px4 - 300 d

  I have a PX4 - 300 d, which was not used for some time, and readers have been removed for something else. I'm looking to return to service as storage for a VMWare ESX host iSCSI. I put new readers in and started, it took a bit, but she finally found the dhco server and made an IP address. I can access the px4 - 300 d, but it's a secutiry configuration screen and I can't spent to set up the storage. Is complaining about the Security screen "can not configure security up to this storage is configured.

  So I'm in a catch 22, so I want to just reload the firmeware and start from scratch. There is no data on the drives, nothing in the configuration of the PX4 - 300 d, which is necessary.

  And the best thing is the big missed 30 days ago and support is not interested to talk to me. they will provide this utility? I know it exists they sent me a version of it about 2 years ago although he has failed, they had to send me a replacement unit.

  Anyone know how we can get a copy?

  Thank you

  Jmorrison919,

  The imager can be engaged on the forums, but you can contact support here:
  https://Lenovo-na-en.custhelp.com/app/ask/

• I want to recreate the image on my laptop but I'm going to lose my microsoft software?

  I want to get my laptop reconfigured sometime soon, but I want to install my microsoft first pack, I can start on some work. But if I do, will I lose my through my laptop microsoft software being released image? and I have to install another new microsoft pack?
  Thanks, I hope you can help.

  Hi Sophie,.

  As long as you have a software license, after creating the image you can reinstall the same on your laptop!

• AIP - SSM recreate the image in secondary ASA 5500 (failover) with virtual contexts

  Hello guys,.

  The scenario is as follows:

  2 ASA 5500 with virtual contexts for failover.

  The ASA elementary school has the work of the AIP-SSM20.

  ASA school (which is in active / standby) has its SSM20 AIP to work now and everything is in production.

  Someone tried to configure this 2nd AIP - SSM, changed the password and lost, so I tried to re - the image (without authorized passage recovery), but the connection fails on the TFTP server, where is the image of the AIP - SSM.

  Now questions, documentation Cisco re-imaging view orders under ASA #.

  but as this scenario has several virtual contexts the ASA # shell contains no IP address as you know (which I suppose is the reason why the ASA cannot download the image from the TFTP server) and switch to another context (ASA / admin #) re-imaging commands do not work (hw-module module 1... etc...).

  What is the solution? Is there documentation for it (with security contexts)?

  Thank you very much for reading ;) comment on possible solutions.

  Yes,

  Some things to keep in mind.

  (1) run 'debug module start' on the SAA before running the command "hw-module module 1 recover boot. This will show you the ROMMON of the MSS output as it tries to make the new image and you can look for any errors.

  (2) before trying to download from the SSM, first use a machine separate download tftp from your laptop. This will ensure the TFTP on your laptop works and confirm what directory (if any) that you can use as the file location.

  (3) if the tftp download does not SSM, then the SSM is unable to properly connect to your laptop. You need a crossover cable to connect your laptop to the SSM. If you have a crossover cable, then you could try to connect the MSS and your laptop to a small hub, or configure a new vlan on your switch with only 2 ports and connect the MSS and your computer laptop this vlan 2 port.

  (4) also try the download first at the end of the gateway to 0.0.0.0 since your laptop and the SSM will be on the same subnet. If this does not work then you can try a non-existent 30.0.0.4 address as gateway.

  (5) understand that the IP address that you specify for the MSS using the command "configure the hw-module module 1 recover" is just temporary for download. Once an image is installed, then sitting at the module and run the "setup" command in order to configure the permanent address you want ure on external port of the SSM. This address in the "setup" command can the same as that used in the command 'get the 1 hw-module module configure' or a completely new (as in your case). Just make sure that you connect to the network just to what address you give.

• After portable recreating the image, installed programs do not show up in Add or remove programs

  I had a few problems of virus with a laptop from work so HE wiped and did a reimage but now there are only four programs appear in Add or remove programs. There is something of our previous IT person made in the registry very quickly allowing these programs to appear again, but our new IT person can't figure out how to do.

  I have a program that I need to fix, but I can't see in Add or remove programs because of this problem.

  I didn't look at the other person IT close enough to understand it. Does anyone know what could have change registry?

  I should add that I am running XP Professional sp3.

  Thanks for any help you can provide.

  Hi galaxie428,

  The issue of Windows XP, you have posted is related to Windows XP in a domain environment. It is better suited for the IT Pro TechNet public. Please ask your question in the Windows XP TechNet forums for assistance.

  Hope the helps of information.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to recreate the image without disc

  I want to reimage my computer because I have a virus, but I bought a computer that has windows 7 pre installed - how do I reimage without a disc or where can I find the Office

  Some computer manufacturers, including Dell and HP, have a recovery partition on the hard drive of the new computers.  By pressing a special key combination when the computer starts, you can use the recovery partition to restore the computer to the way it was when it was new.

  If your computer has that, contact the computer manufacturer and ask an installation disc.

  After you have re-installed Windows 7, make an image of the backup system, that you can use to restore the system quickly and easily if necessary.

  Boulder computer Maven
  Most Microsoft Valuable Professional

• Recreate the image on new computer or former

  When I reimage a machine with a license of Windows 7 OEM to an image that has a volume license at some point at the end of the preparation of the machine before I can return the OEM license to be able to use a volume license?  In order to not consume a volume license and use the OEM license that is on this unit.  Basically so we are not pay twice for a single machine.  If you could give me the steps on how to do it,

  Thank you

  Dave Aceret

  The fact is the Windows 7 Enterprise volume license is actually an upgrade license and to use it, the computer must be running a qualifying business of premium SKY version full retail or OEM, examples: Windows XP Professional, Windows Vista professional/ultimate, Windows 7 Professional/Ultimate Edition.

  In addition, the machine is supplied already with the OEM license as part of the purchase price. The only way that you would pay several times if the machine had come is pre-installed with say no eligible SKUs such as Windows XP Home Edition, Windows Vista Home Basic/Premium, Windows 7 Starter, Home Basic/Premium. Those is not eligible for the Windows 7 Enterprise, you must first upgrade to a SKU company before you can use Windows 7 Enterprise or professional VL.

• lost the cd to acrobat reader 9.5.5, how can I get the serial number before I recreate the image on the pc, what is?

  A few years, our company purchased Acrobat Reader 9.5.5 Pro for one of our employees. This employee is no longer with us, so we want to clean up the pc and re-purpose it. Unfortunately, we have more drive, in that the program has come. So the question is, how can we get the serial number for the program so that we can reinstall it once the pc is under image?

  Acrobat Reader is free. Acrobat Pro or Acrobat Standard costs money. The problem with serial number is delicate. If it is a payment business with a license so you can connect to your account a retrieve serial number. If it has been registered to the user and he registered the software on a corporate email account, you can probably log on the account and retrieve serial number (I don't know if it's legal, then you can check with your corporate lawyer). If is a an installation an installation of volume then check with the company you bought your contract in volume of might be the best route.

  If you have any of these options at your disposal, you can contact the customer service with proof of purchase in hand. No one will take the word of someone call on a phone, even if they do not tell the truth.

  Please be aware that Acrobat 9.5.5 will not work with several modern operating systems it's quite long in the tooth. You may be able to get some, but not all of the features to work.

• Guarantee rules to recreate the image

  Hello

  I recently bought a Lenovo ideapad Z580 (in India). It comes with Windows 7 Home Basic Edition. I want to know if the hardware warranty will void if I remove the preinstalled OS (I'll keep the intact although OEM partition) and install another OS (probably Ububtu / or even Windows 7 Ultimate). If someone can answer, it will be useful for me.

  The warranty of the equipment would be never cancelled due to the evolution of the os pre-installed.

• The image proportions

  Suppose you have a 2048 x 2048 image in export as, what to export is a 600w x image 325 h; It is somehow a way possible without recreating the image with these dimensions?

  OK, my thing of free processing has failed due to a problem of canvas.  When you reduced the work, the canvas remained and reported the size of the Image as 848 x 816 px your work has been scaled to 547 x 188, but the size of the included image canvas. Trim the image did not catch it.

  So I did a Ctrl a (select > all) for the work and Image > Crop to remove the Web term.

  The size of the image is now 547 x 188 px and then I used Image size to bump it up to 600.

  Your editing in this file table is white. I don't know why.

  Three parts of the document area: cardboard, canvas and Image. Pasteboard is this area outside the canvas, he is not considered the size of the Image.

  The dotted box is your canvas and your real picture is sitting on it. You don't see it, but it is larger than the image and this is why the size didn't make any sense.

  Gene

  

• Size of the image in Illustrator to Photoshop

  I'm new to Illustrator and can only be overlooking something here, but here's my background and the question:

  I took a screenshot of an image and open in Photoshop CS3. I've clipped a part I want to use and save the file as a .eps file and open it with Illustrator. In Illustrator, I recreate the image at the same size as the image I opened (I look at the two images to 100% view). I save my new image in .eps format, and then open it with Photoshop. For some reason, the image is about 50% bigger in Photoshop that was in Illustrator. Any ideas? A percentage of 100% look at a watch not really the right size of the image? Or is the problem lies with how Photoshop CS3 interprets a file .eps Illustrator CS4?

  Thanks in advance for any information or advice.

  You've discovered just resolution image and its effect on the display of the pixel based images.

  In Illustrator, there is no resolution. Objects have a set size and Illy requires a screen resolution of 72 dpi as a basis for hypotheses on the display of graphics as well as for its calculations of this 100%.

  Then export to pixel based on the file formats, you can choose the resolution.

  In Photoshop, the '100% ' has nothing to do with the actual size of things (as defined in Illustrator) but means that one pixel of the image is a pixel of your screen.

  When you open an EPS, you get a dialog box in which specify you how to photoshop must calculate the pixels of the vector and the desired resolution. When you go to 72 dpi, you should get the size you expect. But that won't be enough to print.

  BTW: the workflow to do a screen capture and convert your image here and there may be harmful for printing results.