(Redirected) Speakers with an Alienware Area 51

Similar Questions

• Need help with Overclocking Alienware Area 51 Command Center Application

  Just got my Area 51 today and do not understand how to use overclocking in the command center.  Is there documentation on how to use it.  A couple of "Level1" and "Level2" buttons are displayed, but do not seem to do anything?

  Thank you!

  This is overclocking tool, so that soon you click in the level you want to use and save the changes to the system will change the speed of clocks on its own in real time.

• Profile of Alienware Area - 51 ALX Intel XMP A10 does not work with DDR3 1600 MHz

  I bought three Kingston 8 GB RAM DDR3 1600 MHz 240 pin DIMM that totals up to 24 GB of RAM and install in my desktop computer. When I turned on and the message appeared saying:

  Maternal health and infant is running with DDR3 - 1333 MHz

  WARNING! Previous overclocking failed, and system restore its default value. Press F1 to continue, F2 to enter Setup Menu

  When I access the BIOS setting (version A10), I disabled XMP and then it went through fine after the reboot. However, I have to have XMP allow at any time? How can configure profile 1333 MHz to 1600 MHz XMP?

  What bothers me is that I had three former PIN of Kingston 4 GB RAM DDR3 1600 MHz 240 DIMM which total up to 12 GB of RAM and the XMP worked very well with them before they were 1600 MHz.

  The type of computer I have is:

  Alienware Area-51 ALX

  Intel Core i7 980 Extreme 6 c with 12 MB of Cache

  Windows 7 Ultimate

  Please, help me to solve this problem. Thank you.

  See this:

  http://en.community.Dell.com/Owners-Club/Alienware/f/3746/p/19471694/20209913.aspx#20209913

  And I certainly don't have the answer, but I'll remember these points:

  1. I think that you can set manually nothing XMP adjustable (but with more control).

  2 machines often memory need to be slowed down when you are near maximum capacity look maintenance manuals.

  3 area-51 has never been tested or even allow the 8 GB DIMMs. You are in the new territories.

  4. If you really need 24 GB (and it works at 1333) then the 267 speed drop is insignificant.

• (Redirected) ALIENWARE AREA 51 AND GTX 1080

  hi, do you know if in the future there will be the opportunity to buy the Alienware Area 51 already with the GTX 1080 ? ( single double or triple )
  

  Best of this post in the Alienware owners Club Forum, here:

  http://en.community.Dell.com/Owners-Club/Alienware/default.aspx

  Bev.

• (Redirected) Dell Alienware Area 51 new model

  I bought a dell alienware are 51 desktop PC I just deliver on Friday.  I would like to add another 980 Nvidia gtx card to that, but the SLI bridge comes in 3 different sizes, short, medium and long.  What I want to know is which bridge of size I need.  I can't find an image of hard drive so I don't know if pci express ports side by side or y at - it a regular PCI between them.

  http://www.GeForce.com/hardware/technology/SLI/bridges

  Best of this post in the Alienware owners Club Forum, here:

  http://en.community.Dell.com/Owners-Club/Alienware/default.aspx

  Bev.

• (Redirected) Add the second SSD to Alienware area 51 R2

  Hello, I recently bought a new Alienware Area 51 R2, currently I have a 128 GB SSD main + 2 TB storage config. I want to add an other SSD, capable of 256 GB. I want to start my games from there.

  My Question is, what would be the best solution for my needs? I see so many types of SSD out there and have little knowledge about the benefits and disadvantages of each.

  Best of this post in the Alienware owners Club Forum, here:

  http://en.community.Dell.com/Owners-Club/Alienware/default.aspx

  Bev.

• (Redirected) Upgrade of RAM for my Alienware Area 51 R2

  I need to upgrade RAM in my Alienware Area 51 R2 currently having DD4-2133 Non ECC RAM, 8 GB in 2 homes, 4 GB each in Total. My question is, can I use DDR4-2133 RAM ECC, 16 GB stick in the four locations, a total of 64 GB of RAM?

  Better in this position in the Alienware owners Club Forum, here:

  http://en.community.Dell.com/Owners-Club/Alienware/default.aspx

  Bev.

• (Redirected) Alienware Area 51 R2

  I recently bought an Alienware Area 51 r2. Its been works like a charm, until recently. I have about 4 months and recently he shot himself. I push the power button to turn it off, and it turns on. Sometimes it's instantly, sometimes it's a few hours later. There is no model really. Is there a way to check it and see why it is light on its own?

  Better in this position in the Alienware owners Club Forum, here:

  http://en.community.Dell.com/Owners-Club/Alienware/default.aspx

  Bev.

• Problem updating display on Alienware Area-51 m15X Vista drivers

  Hello. Recently, I had a virus on my Alienware Area-51 m15X. It finally did my restore my computer to its factory site. Most of the drivers was missing. I reinstalled my wireless card driver and the graphics driver, but the graphics driver does not work correctly. I uninstalled and went on the Web from NVIDIA site to reinstall the appropriate driver, and it still doesn't work right. I used Driver Sweeper to clean all the files on my HARD drive that are associated with the NVIDIA device in safe mode. I reinstalled all the and restarted my computer and I still get the error message. I can't send it because it is not under the manufacturer's warranty, and I have little money to send it to Best Buy Geek Squad. Please, if there is a way to solve this problem, even though it requires the formatting of my HARD drive, I'll be ready to do so.

  I solved the problem. For future use, if you own an Alienware or use the NVIDIA 8600 M GT card, uninstall the driver using Device Manager and use the driver Sweeper to remove all traces of the driver. Once this done, do not restart, but go on the alienware website and download the NVIDIA driver (you must know your operating system, ect. ect. for the driver) and install it. Windows will say that his signature is unreadable. Click on install anyway. reboot and your laptop must be as new :D

• Alienware Area 51 (ALX)

  Hello

  I have an Alienware Area 51. I think that's not the ALX, but I'm not sure. I have a few questions:

  1. the Dell website does not recognize my service tag when I he returned in product support, my tag is the NOTE from the ADMIN: maintain the label removed according to the rules of confidentiality > (generated by the system Dell detects)

  2. I think that my collar closed not automatic, but how can I be sure? I see that somewhere?

  3. the active ventilation does not work correctly. 2 fins are not going up, they get stuck after one or 2 centimeters. They go down in the normal way. How can I fix?

  Thanks in advance

  Remove the two side panel access doors. Remove your signs of topping top skinny black acrylic finish on both sides of the case so you can access to the fins, their hinges and screws. When you turn on, look to see what makes your 2 flippers paste. If you need to, "help" take off. Command center can open, active evacuation, have CC open the fins and close once or twice. Do test for bonding. Usually, it comes down to the torque of the screw end, or the torque of the screws of the trim panel. Unless of course you can see what is the cause of bind, as an obstacle.

  You can try back a little torque on the screws of the fin on the 2 fins that stick. Reinstall the screws to the appropriate if - couple when they return to normal. Retest w/Command Center, open/closed. If everything is fine, reinsert the finishing trim panels and reinstall the screws, but not too tight just yet. Repeat the test with the command center to open the closed fins. Usually, the screws from trim to finishing nearest you for what purpose clings is the culprit, then tighten or loosen based on the question whether one of these tips have helped. As long as the finishing pad screw is almost tight, it will keep the filling and not make the stick of fin...

  Basically, remove your doors case, remove the upper trim, power and go from there...

• Alienware area 51 25 fps...

  Hello

  Sorry for my bad English, I'm French,

  I have Ben Ali recently an Alienware Area 51 with 32 GB of Ram and 2 graphic cards Nvidia Gtx 960, I activated the SLI.

  I have a few games 400fps as League of legends/rocket League etc. in Ultra quality.

  But in other games like Rainbow Six seat or the forest, I need to be in the moderate to get 20-30 FPS... I have a monitor dell of 3840 x 2160...

  Can someone explain/help me why so I have less FPS?

  Thank you very much for your help,

  Antoine Bedaton

  The fps you get seems quite normal for this resolution with these cards as it turns be 4K resolution. Try to run games in 1920 X 1080?

• Alienware area 51 bumps on the edges of sewing?

  Hello, do all the alienware area 51 have little bumps very very small metal on the edges of the seams when there is a gap on the side where the two metal parts connect to form the handle? tied of arrows with what we talk about.

  

  Mine has no defects noted thereon. While I agree this is a minor flaw in your, you also have the right to complain and make use of your resources with Dell

• 5.1 speakers with Creative Sound Blaster Live! Center speaker and sub plays not

  5.1 speakers with Creative Sound Blaster Live! Sub and center speaker plays only not to aid the Winodows Sound Test tool found in the READING DEVICES > CONFIGURE

  I tried to connect the speakers on my other PC Windows 7 and it works, I tried 2 different PCI on the problem computer sound cards and still no luck.

  Front right, front left, rear right and rear speakers left are OK and will be made a sound of "hung" when I click on them in the graphical display, but from the center speaker, no matter what drivers I have installed, not quite sound...

  Hi paokara777,

  Follow the steps on the below link that explains how to enable the sound surround using SBLive Application.

  http://h10025.www1.HP.com/ewfrf/wc/document?LC=en&DLC=en&cc=us&lang=en&docName=bph05667

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unable to connect Bluetooth speakers with Windows 7 system

  Dear experts,

  I have a laptop HP Pavilion DV7-2014TX running Win7 Ultimate.

  I just bought a new Bose Bluetooth headset. I tried for 2 hours to try to pair it with my phone, but my laptop is not all bluetooth devices.  I tried as much as I know, but I'm out of ideas. The only thing that I think now is that my laptop is old enough that it is no longer compatible with the version of bluetooth on my helmet.

  Any help would be welcome, thank you.

  George

  Original title: Bluetooth

  Hi George,.

  Thanks for posting your query in Microsoft Community.

  I understand that you can not use headsets Bluetooth of Bose enabled on Windows 7, but I would like to learn more about the issue in order to provide you with better assistance.

  1. You are able to connect and use another Bluetooth device on this computer?
  2. You did it any significant hardware or change software on the computer before this problem?

  The question may arise due to the incompatibility with the Bose headphones Bluetooth driver. Then I suggest that you try the following steps Diagnostics to find out the root cause, apply patches, and check if the problem persists:

  Method 1:

  Try to follow the steps in the following link to resolve the problems with Bluetooth devices:

  The problems with Bluetooth devices

  (Note: article also applies to Windows 7)

  Method 2:

  If method 1 does not work, try to run the patch that is available in the following link and look for the question.

  Bluetooth devices do not work correctly on a computer that is running Windows 7

  Method 3:

  Alternatively, you can try to check if the Bluetooth support service is running.

  1. Click Start, type services.msc in the Start Search and press ENTER.
  2. In the list of services, double-click the Bluetooth Support Service.
  3. Change the startup to Automatic type, then click Start to start the service.
  4. Click on apply and then click OK.

  Trying to connect Bluetooth speakers with the computer and check if the problem persists.

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• Gigabyte of R2 Alienware area 51 GTX 980 TI G1

  HELO everyone

  Ive wanted to change my GPU of a SLI GTX of 970 to a GIGABYT SLI GTX 980 TI G1. Ive been hearing rumors about area 51 R2 motherboard is not compatible, or something? Im not an expert in this so if someone could give me some advice on if it's fixed or not, I would be very grateful.

  My sheet atm are:

  Intel Core i7 - 5930K (6 hearts, 15 MB of cache, the overclocked up to 3.9 GHz w / Turbo Boost)

  Alienware Area 51 1500W chassis

  DDR4 Quad Channel 32 GB at 2133 MHz

  Hand of 256GB SSD 6 GB/s + 4 TB of storage 6kRPM SATA 6 GB/s

  Dual graphics card NVIDIA GeForce GTX 970 with total 8GB (2 x 4 GB) GDDR5 - NVIDIA SLI active

  PS ive purchased my alienware before alienware standard selling area 51 with 980 TI SLI gtx

  Hello

  I just spoke with our support tech LV3 Department and they have advised that there should not be problems with this configuration on the Alienware Area 51 R2. Let us know if you encounter any problems.