Reference Dell PowerConnect 6248 several sessions of surveillance?

Similar Questions

• Dell PowerConnect 6248 10 GB ports reference works do not

  Hello

  We have recently installed a module SFP + (part # c107d) in our Dell PowerConnect 6248 switch. The switch does not seem to see the module because before install us the plug-in, it showed a port xg3 xg4, and after the addition of the module, it shows that these ports.

  So I have a few questions:

  Is the SFP + above compatible with this model of switch?

  If so, how can verify us that the ports are active?

  Here is the result of the port details:

  #show interface ethernet 1/xg3 in detail

  Port Type Duplex speed Neg Admin link

  A State

  -----  ------------------------------  ------  -------  ----  -----  -----

  1/xg3 10G - level s/o unknown Auto Up Down

  Port description

  ----  --------------------------------------------------------------------------

  1/xg3

  Flow control: enabled

  Port: 1/xg3

  Belonging to a VLAN: access mode Mode

  Operating parameters:

  PVID: 1

  Capture filtering: enabled

  Acceptable frame type: no label

  Default priority: 0

  GVRP status: Disabled

  Protected: disabled

  -Other - or ITU (q)

  Port 1/xg3 is a member of:

  Rule of VLAN name evacuation Type

  ----    --------------------------------- -----------   --------

  1 by default not marked by default

  Static configuration:

  PVID: 1

  Capture filtering: enabled

  Acceptable frame type: no label

  Port 1/xg3 is configured statically:

  Output name rule of VLAN

  ----    --------------------------------- -----------

  Prohibition of VLAN:

  Name of VLAN

  ----    ---------------------------------

  Port 1/xg3 Enabled

  Status: Disabled role: disabled

  -Other - or ITU (q)

  Identification of the port: 128.51 shipping cost: 0

  Fast port: No. (configured: no) root Protection: No.

  Designated the bridge priority: 32768 address: 80:00:00:25:64:19:92:1 C

  Identification of the designated port: 0.0 cost of access road designated: 0

  Root regional CSE: 80:00:00:25:64:19:92:1 C CSE Port cost: 0

  BPDU: 0 sent, received 0

  Yes, this module is listed as compatible with the switch. It seems that you install in Bay 2? He may have listed these ports but they probably do not appear as active. Have you tried to make a connection with ports?

• Connection SAN Dell PowerConnect 6248

  Our switch in our network is the Dell PowerConnect 6248. This switch has a SFP module.

  I was wondering if I could use this module to connect my SAN [activeRAID 32 TB of storage active destocking] and have access to the storage as a network or NAS drive Bay.

  To be more precise I'll be plugging the controller [HBA] San to the SFP module on the 624 of Dell PC via a cable Fibre Channel LC.

  I'm new to SAN configuration and look for the best solution to access the storage on my network.

  Everyone has implemented a San with the SFP Module before; If that set up your look like?

  Fibre channel and ethernet/IP are not compatible protocols without another device that can translate. The 6248 has no support for FCoE. There are switches that support both they are called network switches convergent or unified, although generally the traffic is still separated.

• Stacking Module - Dell Powerconnect 6248

  Hello. I have a Dell Powerconnect 6248. This used to be a secondary switch in a stacked configuration (total of 2 switches). However, the captain then descended down we unplugged and it became the master of the battery. It is always configured in a configuration of the battery.

  My question is this: can I remove the stacking module card when the switch is on and in production?

  The reason is that I bought a new 6248 and repaired the old master as well and want to stack these two because they are both on the latest firmware. What is the best practice for this that I don't want to take down the switch by disconnecting the battery module.

  Let me know if you need more information!

  Thank you very much for any information!

  Unfortunately the stackable modules are not hot-swappable. You must turn off the appliance to remove the stacking module.

• Reference Dell PowerConnect 2824 remove connections, odd led models

  Hello

  We are noticed on some of our Dell PowerConnect 2824 switches that our devices are connected to the switch suddenly disconnected.  Our devices are a network of small size with the switch, where we connect up to 12 devices and use DHCP to assign IP addresses to the devices.  We also monitor the network with a Windows laptop.  We have also seen times where the switch itself seems to be restarted and shows amber LED light up successively from left to right on the top row of ports, then return on the bottom row.  I confirmed that we use version 1.0.0.45 software for the switch in question.

  We have also seen situations where all, except one device remains connected, but when trying to reconnect to the device has fallen, it seems that the switch seems to completely ignore the device regardless of the port where we connect to the switch.  We tried other cables, but the problem persists.  It's the kind of behavior that I could wait if the MAC addresses are not unique, but all of our devices have all custom MAC addresses.

  Another issue is that we use a very short lease period of one minute.  I don't know if this will get us in trouble.

  If you need more specific information, I'll try to answer your questions.

  Thank you.

  Bob

  Hi Bob,

  If it happens on several switches it is probably not a problem with the hardware switch. It could be a matter of Spanning Tree where it lacks a Hello and due to the lease really short DHCP is originally from the port to close before it can restore a link. You can try to turn STP or enabling quick link on the ports for end devices.

  Why do you have the DHCP lease on so little time for only 12 aircraft? It would add a lot of network traffic. You can try and have some machines on static IP and see if it still falls these ports.

• Reference Dell PowerConnect 2848 OID for CPU time and memory

  Hi all

  This is my first post in this forum. I searched all the messages that can solve my problems, but I could not find so if there is already an existing post and I couldn't find it please guide me to it.

  My case is. We have a few Dell PowerConnect 28xx switches in our network. We want to monitor things like the CPU, the temperature, the use of the RAM usage. We use Solarwinds IpMonitor monitoring tool. I downloaded the MIB, I could find the download of Firmware from Dell drivers and downloads page. I went through the entire MIB, but I couldn't find an OID for the foregoing.

  So if anyone can help me please what OID is used for usage of CPU and RAM temperature it will really help me.

  Please let us know in case we need more information on my side.

  Thank you

  Frank Moreau

  I did use SNMP on the 28xx but here are some various sensor OID, I used for the N-series, as well as some older models Powerconnect.  I don't know if they will work for the 2xxx, but you can try one or two and see if they work.

  N - Series (FW 6.2 and later versions) temperature OID
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.5.1.0
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.5.1.1

  62xx (3.0.x.x firmware or later-, some may also work with 2.x firmware)
  Temperature OID
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.2
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.3
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.4

  Are the OID to use CPU for N-Series switches
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.1 (total free memory)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.2 (total memory)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3 (table for the following...)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.1 (index)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.2 (name of the process using CPU)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.2 (% CPU used by the corresponding process)
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.4.0 (cumulation of all the activity of the CPU)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.9 (CPU utilization shows 5 s, 60 s and 300s).

  OIDs memory
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.1
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.2
  Power supply OID
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.7.1.2
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.7.1.3
  OIDs of fan
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.2
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.3
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.4
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.5

  35xx (2.0.x.x or later firmware)
  Temperature OID
  . 1.3.6.1.4.1.89.53.15.1.9
  . 1.3.6.1.4.1.89.53.15.1.10
  OIDs of CPU
  . 1.3.6.1.4.1.89.1.6
  . 1.3.6.1.4.1.89.1.7
  . 1.3.6.1.4.1.89.1.8
  . 1.3.6.1.4.1.89.1.9
  OIDs memory
  . 1.3.6.1.4.1.89.29.11.1
  . 1.3.6.1.4.1.89.29.11.2
  P.S. The OID
  . 1.3.6.1.4.1.89.35.5.1.1.2
  . 1.3.6.1.4.1.89.83.1.2.1.2
  . 1.3.6.1.4.1.89.83.1.2.1.3
  . 1.3.6.1.4.1.89.83.1.2.1.4
  . 1.3.6.1.4.1.89.53.15.1.3
  . 1.3.6.1.4.1.89.53.15.1.3
  OIDs of fan
  . 1.3.6.1.4.1.89.83.1.1.1.2
  . 1.3.6.1.4.1.89.83.1.1.1.3
  . 1.3.6.1.4.1.89.53.15.1.4
  . 1.3.6.1.4.1.89.53.15.1.5
  . 1.3.6.1.4.1.89.53.15.1.6
  . 1.3.6.1.4.1.89.53.15.1.7
  . 1.3.6.1.4.1.89.53.15.1.8

  for old firmware - if the 35xx above does not work:
  Temperature
  1.3.6.1.4.1.674.10895.5000.2.89.53.15.1.9 (Celsius)
  1.3.6.1.4.1.674.10895.5000.2.89.53.15.1.10

  I hope this helps.

  B

• Reference Dell PowerConnect 3524 - "SW3P_callback_rx_frame - arp - scrapped intervention."

  Hello everyone.

  The company I work for, I test switches to see who is good and who is bad. I've already marked the switch in question as 'bad' for these mistakes - but I've never seen this error before. My colleagues have not either. Therefore, I ask the community what kind of error is what it means and whether it is potentially fixable.

  My device is a Dell PowerConnect 3524. He is currently out of warranty.

  What I did: I have deleted the startup configuration and then run the Setup Wizard. I put an IP address, gateway, and password. The rest, I left the default values. This configuration works on all switches that I have ever tested, including this model, so I think that this configuration is not serious.

  Then I plug in an ethernet cable in all ports and the other end into a very small 5 port switch that also has other trendy items above, the phone and my main computer. They all get internet, I don't think that there is a problem.

  I plug another cable in another port of the switch and the other end in a laptop sitting on top of the switch (my laptop test).

  I start ping the local firewall and run it with the "-t" parameter so it does not stop.

  It is fine for about 5-10 minutes usually. I can trade ports and others and she'll pick up ping soon and do what it is supposed to. After plugging into the wrong port, (7 or 8), I get the error "SW3P_callback_rx_frame - intervention arp - put the scrapped." and cannot pass traffic. PuTTY shows that the connection is established and transfer, but the ping is not possible.

  I am only an intern, this switch is not vital and will be sent to the "cemetery" and all my business done with switches will be. I am just curious to know what it is. Anyone know what it is and what could be done to solve the problem?

  Thank you for your time!

  I couldn't find any relevant information on this error message. With errors that occur only on specific ports and a new configuration, it really sounds as a kind of material error. Will there be another message that accompany this message? If you haven't already done so, re-flashing the firmware of the switch can help ensure that the message is not caused by an image that has become corrupt.

  http://Dell.to/1XmQxPU

• Reference Dell PowerConnect 6024F get mac by ip with arp and more option

  Hello in the DELL community.

  I hava a little question, and hoping to find some answers here ;) I'm writing a small script, and in this script, I need to get the mac address is to link to Ip address of the ARP command. I am using telnet to connect to DELL. But the show arp command displays a lot of information, a huge list of ip. I tried to analyze, with the '' option and press etc., but it's a very slow procedure.

  Two main issues:

  1. how to get the mac address and link it to the IP by ARP command

  2 how to get rid of the option ''. I mean show cli without

  I thank the of to get answers.

  P. S.

  ===========================

  Switch: Dell PowerConnect 6024F

  # See the worm
  SW version 2.0.0.19 (date may 5, 2008 time 16:33:30)
  Start the version 1.0.0.13 (August 13, 2003 time 15:28:31)
  HW version 00.01.64
  #

  Show arp? -> watch only

  Show arp
  

  Terminal Server? -> watch only

  Terminal Server
  history

  He might have an OID you can pole for this info. all the OIDS are in the MIB that are included in the download for the firmware.

  www.dell.com/.../DriversDetails

  If you do not find one in the MIB, you might try a SNMP walk on the switch to see if you can identify an OID that will provide you with this info.

• Reference Dell PowerConnect 3048

  Hello!

  I have a Dell PowerConnect 3048 I want to use it on my home network. For now, my network is small, but as the days pass, he has grown. The problem, I'm running, even after the request of Google, is that I have a hard time finding a way to be able to configure this option. The switch has the power, and I also have the DB - 9 to Ethernet cable from the console.

  For this particular option, the console port is the business end of DB-9 while the end of Ethernet connects to what I presume, a computer. Again, the problem is when I connect the cable from the console of the computer, the switch and use HyperTerminal or PuTTY, I can't speak to this switch. I don't understand what I am doing wrong?

  A lot of reading and watching videos, I understand that some switches have a console, but on this particular switch Ethernet port, it doesn't have such a port. Please guide me on how I can talk to this switch so that I can get configured for my home network.

  Kind regards

  The original cable was a db9 to db9 cable. You can try another cable, like a db9 to usb.

  The switch's default IP address is 192.168.0.1. Then you could try a telnet connection too. See that you have a better success rate.

  www.dell.com/.../ArticleView

• Reference Dell Powerconnect 3024

  I just bought a Dell powerconnect 3024 on ebay that apparently has been decommissioned corporate. Based on the serial number, warranty or service with Dell expired? Or the seller or the company, that he came remembers the password so the only alternative is to reset the switch, but there is no reset button. No one seems to remember the password and I need to get and put in place. Dell will not help not because of the warranty has expired. Help. For reasons of security if you want to send me the instructions that will be very well. email is [email protected].

  Thank you

  
  

• Port Mirroring a LAG on stacked Dell PowerConnect 6248 s

  Hello

  It is possible to port mirror use as a source, a SHIFT, consisting of 4 ports (2 in each Member of a set of 6248 s PowerConnect stacked). Whenever I'm trying to add the source, using GUI, I get an error:

  Error! There not together "Type" with "Tx and Rx" error occurred in FILTER_MISSING

  This allusion is what filter?

  I can't select a spring, unit 1 or unit 2, members of the LAG, like the gui only shows them not from the ports drop.

  Thank you.

  Unfortunately, the switch is able to mirror individual ports as source ports. You can check this by trials of establishing a mirror session where the source port is not part of a LAG.

• Proxy-arp or local proxy arp? Reference Dell Powerconnect 6224

  We need allow some customers to resolve the mac address of a server that is located in a different range of addresses, VLAN and IP.

  I thought that the addition of the ip proxy-arp interface command vlan should do the job, but this command seems to be activated by default according to the reference guide, after that I tried to add the command he always show up on a running show. Which confirmed my thoughts. While I was looking for the solution that I saw another command that does not appear in the cli reference guide: local-proxy-arp ip. But since I'm not sure of what will make this command I am careful to hit just the command on the interface VLAN.

  How others send their arp on powerconnect 6224 requests?

  After reading my own source again, I realized that the thing that I want is not possible. It goes beyond the need to divide the network into segments. If all the query arp is transferred to other networks, there is a benefit less: you want to limit the broadcast domain.

  Static ARP is the thing I'm going to need to be implemented to solve this problem.

  Thanks for the clarification anyway.

• Reference Dell PowerConnect 8024 - 802.3ad (dynamic LACP) through 2 switches?

  We evaluate the use of switches Dell PC8024 to upgrade our backbone to 10GbE.  We use currently HP ProLiant servers with multiple network cards are associated.  The servers support 802.3ad HP dynamic aggregation of links (LACP).

  The switch PC8024 does support the aggregation of dynamic links through 2 different switches, or should it be on the same switch?

  In comparison, the HP2910 switches can support aggregation (LACP) dynamic links across multiple switches, while the HP2920 switches can.  If some can, some can't.  Need to understand the ability of the switch to PC8024.

  Thank you!

  -Terry

  Hello Terry,

  The 8024 does not support a SHIFT of two different switches, the only way it would work, if the switches are stacked and effectively a single switch. If you have used the new series N4000 they take over MLAG, allowing for the OFFSET will be in both switches and they communicate via a peer.

• Reference Dell powerconnect 5524 cannot ping between coelio and trunk port

  Hello...

  We set up a new switch of 5524 I untagged on vlan 20 and access ports where vlan 20 I allowed. I created a computer on the access port on the same trunk port ip net... cant ping beween them. I'm no expert of switch, so I wonder what I missed. I did the same thing on a dell old 3524 and it works directly...

  Here's the port config I tried to do a ping beween is 6 and 10 ports

  (Another thing, how how to remove):

  switchport mode trunk
  switchport access vlan none)

  Any help would be greatly appreciated!

  interface vlan 1
  IP 88.131.90.252 255.255.255.240
  !
  interface vlan 5
  the name 'SCE CJA'
  !
  interface vlan 6
  the name "out of Tele2.
  !
  interface vlan 7
  name "Outside Telenor"
  !
  interface vlan 8
  name "TDC Multivrf"
  !
  interface vlan 20
  TDC-CISCO-LAN name
  !
  [0mMore: , quit: q or CTRL + Z, one line: interface vlan 21]
  the name "FW inside."
  !
  interface vlan 99
  name «FW sync»
  !
  gigabitethernet1/0/1 interface
  Description CPE1
  switchport access vlan 5
  !
  interface gigabitethernet1/0/2
  Description CPE2
  switchport access vlan 5
  !
  interface gigabitethernet1/0/3
  Df description
  spanning tree portfast
  switchport mode trunk
  switchport access vlan no
  !
  interface gigabitethernet1/0/4
  Description Oupps-cb2
  [0mMore: , quit: q or CTRL + Z, a single line: spanning tree portfast]
  switchport mode trunk
  switchport access vlan no
  !
  interface gigabitethernet1/0/5
  Upp-ccm1 description
  spanning tree portfast
  switchport access vlan 20
  !
  interface gigabitethernet1/0/6
  Oupps-ccm2 description
  spanning tree portfast
  switchport access vlan 20
  !
  interface gigabitethernet1/0/7
  Tdc-multivrf1 description
  switchport access vlan 8
  !
  interface gigabitethernet1/0/8
  TDC-multivrf2 description
  switchport access vlan 8
  !
  [0mMore: , quit: q or CTRL + Z, one line: interface gigabitethernet1/0/9]
  Description Oupps-cb-tq03
  spanning tree portfast
  switchport mode trunk
  !
  interface gigabitethernet1/0/10
  Description Oupps-cb-tq04
  spanning tree portfast
  switchport mode trunk
  !
  interface gigabitethernet1/0/11
  Tele2-outside description
  switchport access vlan 6
  !
  interface gigabitethernet1/0/12
  Tele2-outside description
  switchport access vlan 6
  !
  interface gigabitethernet1/0/13
  Telenor-outside description
  switchport access vlan 7
  !
  [0mMore: , quit: q or CTRL + Z, one line: interface gigabitethernet1/0/14]
  Telenor-outside description
  switchport access vlan 7
  !
  interface gigabitethernet1/0/15
  Description Word-Oupps-fw-tq01-inside
  switchport mode trunk
  !
  interface gigabitethernet1/0/16
  Description Word-Oupps-fw-tq02-inside
  switchport mode trunk
  !
  interface gigabitethernet1/0/17
  FW-sync description
  switchport access vlan 99
  !
  interface gigabitethernet1/0/18
  FW-sync description
  switchport access vlan 99
  !
  interface gigabitethernet1/0/19
  Description Word-Oupps-fw-tq01-outside
  [0mMore: , quit: q or CTRL + Z, a single line: switchport mode trunk]
  !
  interface gigabitethernet1/0/20
  Description Word-Oupps-fw-tq02-outside
  switchport mode trunk
  !
  interface gigabitethernet1/0/22
  FW-Sync description
  switchport access vlan 99
  !
  interface gigabitethernet1/0/23
  Description Word-Oupps-FW-tq01-outside
  192.168.11.1 IP address 255.255.255.0
  switchport mode trunk
  !
  interface gigabitethernet1/0/24
  Description Word-AIN-LAN-SW
  switchport access vlan 20
  !
  IP route 0.0.0.0 0.0.0.0 88.131.90.241

  [0mMore: , quit: q or CTRL + Z, a single line:]

  Information of VLAN

  The name of the VLAN Tag Ports Ports unmarked Type permission
  ---- ------------ ------------------ ------------------ --------- -------------
  1 1 article gi1/0/3-4, default required
  Article gi1/0/9-10
  item in gi1/0/15-16,
  item in gi1/0/19-21,
  item in gi1/0/23,
  item in gi1/0/25-48,
  TE1/0/1-2.
  GI2/0/1-48.
  TE2/0/1-2.
  IG3/0/1-48.
  TE3/0/1-2.
  IG4/0/1-48.
  TE4/0/1-2.
  IG5/0/1-48.
  TE5/0/1-2.
  GI6/0/1-48.
  TE6/0/1-2.
  gi7/0/1-48.
  TE7/0/1-2.
  gi8/0/1-48.
  TE8/0/1-2, m 1-32
  5 CPE TDC article gi1/0/3-4, item in gi1/0/1-2 permanent required
  [0mMore: , quit: q or CTRL + Z, one line: article gi1/0/9-10]
  item in gi1/0/15-16,
  item in gi1/0/19-20,
  item in gi1/0/23
  6 outside section gi1/0/3-4, item in gi1/0/11-12 permanent required
  Tele2 item in gi1/0/9-10,
  item in gi1/0/15-16,
  item in gi1/0/19-20,
  item in gi1/0/23
  7 outside article gi1/0/3-4, item in gi1/0/13-14 required permanent
  Telenor item in gi1/0/9-10,
  item in gi1/0/15-16,
  item in gi1/0/19-20,
  item in gi1/0/23
  8 TDC Multivrf item in gi1/0/3-4, item in gi1/0/7-8 permanent required
  Article gi1/0/9-10
  item in gi1/0/15-16,
  item in gi1/0/19-20,
  item in gi1/0/23
  TDC-CISCO-LA 20, article gi1/0/3-4, item in gi1/0/5-6, item in gi1/0/24 required permanent
  N item in gi1/0/9-10,
  item in gi1/0/15-16,
  [0mMore: , quit: q or CTRL + Z, one line: item in gi1/0/19-20,]
  item in gi1/0/23

  In safe mode the PVID is 1 VLAN by default. You can do this by entering the command #switchport trunk vlan native {number of vlan}. If Cisco is configured to accept and send the marked packets and has an IP address in the subnet of VLAN 20, it should be able to communicate with other devices in VLAN 20.

• Reference Dell Powerconnect 6224 DVLAN-mining (Q in Q)

  I have two sites, one is our data center and the other is our office.

  I want to be able to access the data center to the office network, I need access for 2 VLANs, the ISP has already installed it is fine for this and now there's only the part configuration

  At the office, there is a PC5548 and data center, there is one PC6224.

  Office on the incoming port configuration is:

  tengigabitethernet1/0/1 interface
  switchport mode trunk

  The port for outgoing data center conf is:

  interface ethernet 1/g22
  Description "TELEV6RK".
  switchport mode general
  VLAN allowed switchport General add 3000
  dvlan-tunnel mode

  This does not work, how do I configure ports, do I have to configure all ports or only 1 port IDE oucederomsurlesecondport 5548 and 1 on 6224?

  I got an answer from Dell technical support, on how to do it:

  1. If the marking through ISP is different from DOT1Q then you must change it on the two switches using the command global dvlan-tunnel ethertype and options there are (dot1q, vman or custom)

  2 port 1 and 2 must be port trunk who accept only the 3000 VLAN. Here are the ports that are connected to the ISP.

  3 ports 3 and 4 should be dvlan-tunnel mode configured on them and configured as switchport access VIRTUAL 3000 LAN mode. These are ports that are connected to switches that are for production at both sites.

  4 ports 5 and 6 on other switches must be configured as trunk with tagged VLANs you want to transfer through ISP in VLAN 3000. These are the ports located on the switch of production.

  The topology is here: www.upload.ee/.../Topology-change.png

  I hope that now everyone will have its operation :) Thanks for the help.