Reference Dell T5400 new SSD not recognized

Similar Questions

• HP Pavilion Notebook - 17-f250: new SSD not recognized, Pavilion 17 AMD drivers

  Hello

  I bought the laptop (HP Pavilion Notebook 17-f250) on September 2015 and this September 2016, I decided to upgrade with a 2nd SSD.

  I bought a caddy, placed my SAMSUNG EVO 850 PRO inside, removed the optical drive and then place the CART inside the laptop. It fit perfectly, no problem there.

  But Windows does not recognize it at all in MANAGEMENT OF DISKS.

  It is not here in order to format it, etc...

  My IDE/SATA appears as "AMD SATA CONTROLLER".

  I can not find anywhere no possibility of enablev AHCI etc... My BIOS is not an option to check if the AHCI drivers are enabled or not.

  With the AUTOMATIC DETECTION is my driver: AMD APU A4-6210 with graphics AMD RADEON R3.

  My operating system is WINDOWS 10.

  FYI, I bought another same SSD for my office and worked smoothly. I only have a problem with my laptop, and I can't figure out how to recognize the Windows SSD!

  BR,

  Dionisis

  What caddy you bought? There are a lot of these on the market and some are not made with the highest quality control. You may have it tested with another hard drive?

  Second, the interface for the optical drive is SATA which is ahci. The drivers are not the issue.

  Finally, put an SSD in an optical drive is a little excessive spending from one optical drive interface is slower, so the speed of SSDS is wasted. It would be much better to put a regular hard drive large, slow in the optical Bay for storage. Having an SSD in there won't be fast in all directions. Also, a disc in an optical Bay will not be initiated.

• Satellite L50-A-1CU: new SSD not recognized if SATA is set to the performace

  I changed the hard drive from my toshiba a-1-cu C50, with a 128 GB SSD 830.

  This drive only set on the 'autonomy' work is not a 'performance '.
  (In the performance of the modality, the Bios do not see, or seen once on ten of system startup.)

  This settings in Bios called sometimes "interfaces sata".

  The performances are a quarter more slow (125 MB/s vs. 500 mb/s).

  The hard drive has the latest firmware available.

  There is a solution to finally put on the "performance"?

  Hello

  Indeed, it is very strange question

  However, it would be interesting to know if this BIOS <–>recognition SSD problem appears with the other SSD drives. Have you tested other SSD?

  Otherwise, I think that if this problem would appear with different disc SSD, the BIOS may not be not entirely compatible with various SSD.

• HP Pavilion dv7-6004ea: new SSD not recognized in the BIOS

  Hi I have a want dv7 and is currently using a 700 GB drive HARD However im upgrading to an SSD

  I bought a Sandisc SSD PLUS 120 GB, I cloned the HDD to the SSD, I see partitions

  in windows Explorer when im running HDD, but when I try to boot from SSD I get an error

  error code (3F2) I ran diagnosis but no result without error of ideas? Thank you

  If you use the Apricorn software and a usb cable to SATA it should work.

  I did it several times without problem, except when I got an SSD that was a problem.

  Replace the original hard drive in the notebook.

  Download the latest version of the firmware from the manufacturer to the SSD and install it.

  Once you have done this, try cloning of the OS for the SSD, reinstall it in Notepad and start on the SSD.

• SSD not recognized, in-house or Via USB

  Very long story, there are similar positions here but other situations are not the same as mine or the answers do not explain things very well.  I am trying to replace the hard drive in my MBP mid-2010 with a modern SSD, the manufacturer said it is not formatted (say you need to get in shape first of all, in response, saying that their operating system does not recognize in some way, shape, as is my case).  When I put it in the internal drive Bay I get the big "?", sometimes alternates between it and the icon of the Apple and the circle with a slash through it (which means indicates that it has not recognized connected equipment).  I bought the cable I need to connect it via the USB port, I have the original hard disk to another external drive that I intend to use to keep my saved MBP, I want to clone the original to the new SSD hard drive, then try to boot from it.  I'm sure I have format the SSD drive, but how can I do if it is not recognized?  When I connect it outside of a Windows machine (7) it is recognised in Device Manager (but not in my computer).

  Thank you

  Format for a Mac

• SSD not recognized on hp envy

  I installed an SSD in my HP Envy J000. It is not recognized by the BIOS.

  HP diagnostic shows the two discs.

  Device Manager displays the two discs.

  "This PC" only shows the original hard disk. "

  The SSD is not formatted if it matters.

  I use Windows 8.1

  This problem has been resolved. Once I formatted the drive, were acknowledged.

• DELL Vostro 1510-drive not recognized

  The energy guy

  Does not have a will to w-OS/Vista DELL Vostro 1510 only not the DVD player. Alert manager says device "this device cannot start" - 10 of the Code. Yesterday tech DELL replaced DVD drive, used, boot disk Windows does not not diskW, said looks like a software problem. What I do next.

  Hello

  Dungeon involved Dell's Support until the problem is solved, check their documentation online and their
  forums.

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/

  ------------------------------------------------------------------------------------------------------------------

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104/

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Dim 4600 adding hard drive Seagate - new drive not recognized

  I bought a ST3500641AS Seagate SATA/300-RK

  That's the one

  http://www.staples.com/webapp/WCS/stores/servlet/StaplesProductDisplay?&langid=-1&StoreID=10001&splCatType=1&catalogId=10051&ProductID=169534&cmArea=SC3:CG6:smileyvery - happy: P1928:CL140461:SS1034645

  I installed it, but the new drive is not recognized.

  Do I have to move the jumpers on the motherboard?

  Is the motherboard Intel Desktop Board D865PE

  http://www.Intel.com/design/motherbd/RL/rl_confg.htm

  or

  set the bios at startup?

  or

  What is the problem?

  The old drive is connected with tape.

  The new Seagate I connected using the Interface cable provided in the box.

  I have to go buy some kind of adapter?

  Thanks for the help.

  I forgot to say

  I want to do what you say

  make the primary by cloning Seagate

  and then finally not use the 80 GB.

  Here is more information from another post of mine.

  http://www.dellcommunity.com/supportforums/board/message?board.ID=dim_harddrive&thread.ID=142020

  Thanks for the help.

  CDO

  
  

• Reference Dell A10 946 does not

  See the description in the "title area' above.

  My printer (Dell 946 A10) is not communicating with my command 'print '. I can copy, scan & Fax, but cannot print.

  Hi Lee,.
   
  1 you get an error message when tried to print?
   
  We recommend that you download and run Microsoft set to find and correct printing errors. To do this, visit the following link and click on the "Run now" button: http://support.microsoft.com/gp/printing_problems
   
  Visit this link for more information on "Solve printer problems":
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems
   
  I hope this helps.
   
  Thank you
  Syed
  Answers from Microsoft supports the engineer.

• DVD drive on the new computer not recognized

  Hi can someone help.

  My computer did an automatic update at the weekend and now the DVD shows also not recognized.
  I thought about uninstalling and reinstalling would do it.
  Now, I can not reinstall so am without a dvd player on my all-in-one which I desperately need.
  Help!
  Any help would be appreciated
  Thank you

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  Fix for CD/DVD drive missing:

  http://support.Microsoft.com/kb/982116

• Dell Latitude e5440 - Samsung 850 EVO mSATA SSD not recognized

  I bought a new 500 GB Samsung 850 EVO mSATA SSD for my Dell Latitude e5440 (running Windows 7 Pro).  The new player was not visible in 'Computer', so I downloaded, installed and ran the software Samsung magician.

  Samsung software shows that the drive is present.  And there is a button "Validate" - I clicked on - and now: ' Drive Health Status: Good ' and ' serial number: true "appears.

  However, the SSD is not visible when I double-click on computer and the Samsung software States:

  a. "AHCI Mode. Disabled (IDE or RAID).  AHCI mode is necessary for the best performance of the SSD. »

  b. SATA Interface s. o. cannot detect SATA interface details.

  c. s. o. OS OS optimization is supported only for disks using an operating system drive.

  Question 1: Activation of this AHCI mode will allow Windows to recognize the SSD?

  Question 2: How do I?

  Question 3: Activate the AHCI mode "switch off" (logout) my HDD 2.5 "?  (I want to keep Windows 7 to 2.5 "HARD disk and install Windows 10 on the SSD to have a dual boot system, until I got used to Windows 10).

  Inside of your battery compartment is a label with your license key Windows 7 OEM on it.  Photograph it.

  Download and prepare a USB key with a copy of Windows 10 TH2 Pro.

  Remove the disk 2.5 "and connect the new drive mSATA.

  Boot the system to the USB key.  10 Windows Installer should be of the presence of the DSS and will allow you to do the installation of Windows 10 - which in turn is almost certainly going to install the network driver suitable for your system without the need to add anything else.

  USE your 7 product key when prompted and you should be all set.

  Once this is done, you can reconnect the disk 2.5 "If you want to do - but remember that 10 installation is done separately from the 2.5 disk".

• Qosmio G30: Upgrade Vista session: new RAID not recognized

  Hello everyone

  I tried to upgrade vista manual upgrade option, but 2 problems have occurred:

  1. I could not remove these applications (are not not in Control Panel > Add/Remove)
  -> Bluetooth ACPI by Toshiba
  -> TOSHIBA TV TUNER
  -> Nvidia nView Desktop manager
  -> windows 5.1 msnger

  Then, I ignored them and proceeded, I faced a new problem, the new RAID drivers cannot be recognized in the partition screen.

  If I could solve these problems, I get vistaif you have any ideas it would be great.

  Hello Togan,

  Good to see you, engaged with the issue of Vista g30.
  This thread will be important for us, all owners G30 and the g20.
  We stay with you, watch and learn listening and if possible to help you.
  But as I don't have a model g30, let's wait for each of you, out there with the same purpose.
  Help togan and us by your advice and suggestions in relation to our Qosmios.

  First tip: as I told you, please start by a new installation of Windows Vista. Switching from XP to Vista, is not the best way to follow.

  See you soon,.
  Francisco

• CQ50-130US: CQ50-130US SSD not recognized

  My in-laws CQ50-130US has a scratch disk, but the machine is SO slow I want to update a 5400 RPM for one SSD and windows Vista 7 (or maybe 10). I installed a Sandisk Plus 120 GB SSD but can not get the system to recognize it. I can see it using a USB docking station I have on another machine, I even formatted it so the drive seems to be OK.

  I updated the BIOS of F.25 to F.65. The BIOS will start to test the drive (because I don't know what all the test consists of I cancel immediately so I use unnecessarily) and if I remove the disc test fail... so the BIOS sees it, but when I get to the windows installation, Windows is unable to find a drive to install on.

  I google a certain number of things, but what I found doing the litle is meaningless, as it said that it should be a 256 GB for the BIOS drive to see, but it doesn't seem to be the problem.

  I had to use the drivers when I install disks to a RAID controller and which seems to be what windows 7 is looking for here, but too sholdnt happen.

  I'd appreciate help if there is to be

  At any time.

  I am pleased to have been of assistance.

  On a newer platform, I think any SSD will work.

  On the largest, it's a crap shoot.

  As I wrote yesterday, I have a HP 6930p notebook with the same chipset that you work the CQ50, and I installed a 330 Intel 120 GB SSD in this one and it works great.

  I noticed in the specifications of the HP 6930p, which was the first company PC HP 'officially' supported for one SSD.

• SSD not recognized

  Just got an OCZ 240 GB SSD for my Pavilion DV7
  deleted my backup HDD and pluged in the SSD, rebooted the machine very well, but he does not see the SSD.
  What should I do?

  @Flashphill

  That's all.

  When you access the Disk Manager it will appear with a new HARD drive.

  REO

• ProBook 4740 s: new RAM not recognized...?

  I have an old but functional 4740 s Probook, always running on 4 GB of memory. Is no longer worth (especially running programs using a lot of memory as GIMP), and with the upgrade to Win10, I decided it's definitely time to upgrade memory. The max memory for this model is 8 GB.

  According to data IO could find online, I bought Kingston KTH - module X3CS / 4G memory, specified for HP/Compaq. I inserted the memory as far as I can tell, but it does not appear as being recognized. I run the Windows memory checker and found no problem.

  Can anyone suggest what I might hurt?

  Memory module specifications are given as follows:

  Kingston 4 GB DDR3 1600 MHz specific system brand HP SODIMM

  On the Kingston site the Probook s 4740 is not specifically reported as compatible, but they list any of this model. Elsewhere online (IE on thousands of websites of seller) it appears as compatible memory.

  Thanks for any help!

  The most likely cause is that the two modules are not exactly identical.

  It is an essential element of the recommendation that I propose to members who want to upgrade.

  If you want it to run as expected once the new modules are connected, do not mix the types of module or manufacturers.

  Purchase of of another memory identical bar and you shouldn't have problems to start at 8 GB memory acknowledged.