refuse to load the new homepage at startup (Windows 7)

Similar Questions

• Open the home and the new tab at startup.

  Hi all

  I had to reset Firefox and I can't remember or find how to open my home and the new tab at startup.
  Can someone let me know how to do
  Thanks in advance.

  Hi, please see How to set the home page. If you want the new tab Page to start, "Home Page", type on: newtab

  If your question is resolved by this or another answer, please take a minute to let us know. Thank you.

• Error code 101-752 dotnet framework error, problems to load the new software of the printer

  Error code 101-752 dotnet framework error, problems to load the new software of the printer

  Hello

  (1) have you made changes before the start of this issue?

  (2) when you get the error message?

  (3) is the specific question of the installation of the printer software?

  (4) what is the brand and model of the printer?

  It seems that you need to fix .net Framework installed on the computer. Follow this link and see if it helps.

  Fix the .net Framework installation

  http://support.Microsoft.com/kb/976982/en-us

  Note: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756 /) how to back up and restore the registry in Windows

  See also:

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Let us know if that helps.

• I cannot load the new 5.3 LR

  I cannot load the new 5.3 LR with the 1642 error msg?

  Exit Code: 7 Please see specific errors below for troubleshooting. For example,  ERROR:   -------------------------------------- Summary --------------------------------------  - 0 fatal error(s), 2 error(s)    ----------- Payload: Adobe Photoshop Lightroom 5 5.3.0.0 Adobe_Lightroom_x64.msi_5.3 -----------  ERROR: Install MSI payload failed with error: 1624 - Error applying transforms. Verify that the specified transform paths are valid. MSI Error message:  ERROR: Third party payload installer Adobe_Lightroom_x64.msi failed with exit code: 1624  ------------------------------------------------------------------------------------- 

  Hi Blecho,

  You get the same results if you download the update 5.3 directly from here? Lightroom 5.3 now available:http://blogs.adobe.com/lightroomjournal/2013/12/lightroom-5-3-now-avai lable.html

  Let me know how it goes.

  See you soon

  LP

• How can I install Windows 7 onto the new drive while keeping Windows XP on the old drive?

  Wow for on 1 computer install 2 operating systems with 2 hd

  I have 2 hard drives; We have Windows XP and the new one is empty (empty) installed on a computer.  I would like to install Windows 7 on the new hard drive.  How can I install Windows 7 onto the new drive while keeping Windows XP on the old drive?

  Thank you

  Hello

  Sound pretty simple you just need to start from the disc and choose the 2nd hard drive during the installation of windows 7
  your xp will remain such what. every time that you start the system it will ask you to choose which operating system you need
  Start with.
  thanx.

• Why lose the new folder button in windows 7

  Why did you lose the new folder button in windows 7 when you try to create a new folder from a right-click on the desktop?  Y at - it an easy solution to restore this back?

  Difficulty of recording of Linda Yan is not difficult.
   
   

• Load the new XP Pro SP2 OS on Portege R200

  I have a R200, bought in Russia (where I work). I want to install an English version of XP Pro SP2.

  I intend to reformat and install from scratch. Then load all the utilities of Tosh from a CD, I created.

  Loading the XP CD and restart then the installation of Win XP Pro does not recognize Toshiba PCMCIA DVD Rom CD - RW I plugged.

  So I created the 6 boot disks for SP2 on the site of Ms.

  I start from the startup disk, all goes well but until I get to disk 6. Next, I get the windows error blue screen exception etc.

  Beyond that, I can't get to format the drive for a new installation.

  When start I have now the option for the Win XP Pro and WIn XP Russian, although the latter is going into the installation routine that cannot see a CD drive Yes F3 and restart.

  Any ideas?

  As far as I know that you need a support disk Toshiba (PCMCIA card 16-bit cardbus)
  I found an info that the readers should work:
  PA3402E-1DV2
  -PA3352E - 1 CD 2

  To my knowledge, you must press button P and it should be possible to start PCMCIA player. To boot from the disk, you must use the C key.

  Please check these messages:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=6749&MessageID=23319

  In this announcement, you will find the compatible players to begin the process:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=9291&MessageID=32612

  Please use the wonderful advanced search of this forum.
  Here you can search for similar comments that should help you.

• Firefox android opens about.config homepage. Failed to set the new homepage

  Firefox android open always new tab or browser session about: config page.
  I restarted browser and Tablet (Samsung Galaxy Tab 3), and this behavior has not changed.
  All google searches suggest that the firefox browser android home page is not editable, but this is obviously not true.
  I tried the solutions that suggest to navigate to about: home and edit bookmarks and these paths do not work.
  The awesome bar is far from great.
  How to stop the browser from the start to about: config and how can I make the homepage be what I want?

  Solution found:
  Any time by the shortcut of firefox in the section at the bottom of my home screen Quick Launch I got about: config

  Whenever the opening of new tabs for navigation, I got about: config

  I removed the shortcut to quick launch firefox and entered the apps and the firefox shortcut added to quick launch

  The new shortcut follows my customization settings and opens to the best sites now, but also the new tabs to open up to the best websites

  Of course, there is a way to set a homepage of a shortcut somehow

  Unfortunately, this tablet was working properly at the time of purchase and I don't know how to change shortcuts yet, but they can be changed

• After the installation of the new Office 2010 on Windows 7, the system refuses to accept the password after restart.

  We just bought the Sony VPC-CW2S1E with Windows 7, after you install the new Microsoft Office 2010 I restarted the laptop. After trying to enter the password it just keeps refusing and I am at a loss. The laptop came with a recovery CD.

  Any help or ideas are greatly appreciated.

  Contact the Sony Support under your warranty or Service contract.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Printing error after loading the new cartridge

  After loading a new cartridge (genuine) 338, everything I print has the top of the first line is missing. I rebooted the old cartridge and it prints the line correctly (even slightly). I tried to reload a new, but it still does not print correctly. The alignment test after loading was very good. Can anyone help me to solve the problem or is it just a faulty cartridge?

  Rich thanks for your help and for taking the time to answer my question. I'm sorry that I was not to give complete information about the printer, as this has been my first post - I'll do better next time. The issue has resolved itself today! After several attempts to print and reload the cartridge, I dropped, but unexpectedly, the printer has pulled up and began to do a second test of its own alignment, and that solved the problem.

  Sue20

• Load the new Dell XPS 13 9350 via thunderbold usb - c

  Recently bought the new Dell XPS 13 9350, 1080 p with the i5 processor version and I would like to know how to load the xps 13 via usb - c port sight.

  Which cable I'm able to use? I would like to use a male USB - A to USB - C cable to recharge the laptop using usb Sockets aircraft.

  Tracked down the answer:

  It does not simply with phone chargers. He needs Chargers portable a higher voltage. You cannot use cable USB A-To-C to load (unless you have a defective cable seriously, which can damage the charger). You cannot use the Nexus 5 X, 6 p or OnePlus Chargers.

  12-9250 Chromebook Pixel 2 and XPS (and perhaps a few other upcoming 2016 Dell systems) include a USB - C charger that works with the XPS 13 and 15. Chromebook Pixel charger is a wall wart, unlike most chargers for laptop with a brick in the middle.

  Buy a compatible USB - C charger costs as well buy a normal replacement Dell laptop computer charger, so it is honestly not much unless you want to use it on other USB - C devices (whether now or in the future). The Pixel charger can also with phones, but I don't know if the XPS - C USB charger can also.

  You'll also USB - C load with docks. Any USB docking station - C and any wharf 3 Thunderbolt should work with it. Dell has wo of them towards the end of the month of January each offers multiple output video, USB - A, Ethernet, audio ports and in charge. Plugable and some other manufacturers some too.

• Application loader is to expire instead of loading the new binary

  I got an update of the app and a new application rejected because she did not work in 8 IOS (which came out while my applications were in short - no luck!) I have rebuilt the new app that works very well on my ipad. Then I tried to download through the application loader, but it expires only (no error code). I got the last application loader, Version 3.0 (620), but this also expires and does not accept the application. Yes, I'm trying to send the file zip (not the ipa by mistake). I tried all hours of the day and night for 3 days without success. Help, please.

  One thing to try is to go download the latest version of the App Loader that came out today. If that doesn't fix it, you will need to contact the Support Apple Developer. Application loader is their tool and we have no control over it.

  Neil

• Too late to load the new SWF after unloading the current SWF file

  Hello

  In our application, we use more than 10 sovereign wealth funds. When you cross one SWF to others try to unload currently load SWF and load a new. We were successful to unload the existing SWF, but the problem, takes too long to load SWF again (more than 5 seconds). Please suggest a useful method to overcome this time for best performance.

  get an idea of the following code snippet.

  Thank you

  
  public void SwitchSWFs (): void

  {

  If (null! = SystemAgent.getInstance () .currentSWFLoader)

  {
  SystemAgent.getInstance ().currentSWFLoader.unload ();
  SystemAgent.getInstance () .currentSWFLoader = null;
  trace ("HomeUI: previous swf unloaded!");
  }
  on the other
  {

  }
  addChild (SystemAgent.getInstance (.swfLoaderSecondSWF));
  SystemAgent.getInstance () .currentSWFLoader = SystemAgent.getInstance () .swfLoaderSecondSWF;

  }

  
  will call by clicking a button
  public void LoadSecondSWF (): void

  {
  SystemAgent.getInstance (). swfLoaderSecondSWF.load (new URLRequest ("Second.SWF"));
  SwitchSWFs();

  }

  The delay is when you test locally?

  One thing you might try is to load all Chargers present you at the front they are needed so that there is more likely that they are ready to be added to the display list when it is called for.  So instead of having the button trigger loading the SWF, just it call the switchSWFs function.

  Another thing, you could try if you keep it where the Triggers button load the corresponding file to assign an event listener for the charger to detect when it has finished loading and then have this listener event handler function calls the switchSWFs function.  At least this way, the current swf file is not unloaded until a replacement is ready and waiting.

• When you click on a photo on facebook that loads the new popup, Firefox crashes 10 androgenic. Just Firefox crashes and unresponsive. Is there any solution for this?

  When you click a picture that load the popup that Facebook has recently presented on the occasion of just Firefox crashes and unresponsive and them must be closed using the Manager tasks. It does not occur every time say for every 2 of 10.

  That's what the error report says...

  Description:

   A problem caused this program to stop interacting with Windows.
  

  Signature of the problem:

   Problem Event Name:	AppHangB1
   Application Name:	firefox.exe
   Application Version:	10.0.0.4411
   Application Timestamp:	4f2548ce
   Hang Signature:	4813
   Hang Type:	0
   OS Version:	6.1.7601.2.1.0.256.48
   Locale ID:	2057
   Additional Hang Signature 1:	4813d58d219b01045ae1404b21f04466
   Additional Hang Signature 2:	ec05
   Additional Hang Signature 3:	ec057c79f467a3033cec4ebe11500204
   Additional Hang Signature 4:	4813
   Additional Hang Signature 5:	4813d58d219b01045ae1404b21f04466
   Additional Hang Signature 6:	ec05
   Additional Hang Signature 7:	ec057c79f467a3033cec4ebe11500204
  

  • Firefox plant - troubleshoot and prevent assistance fixing crashes
  • Firefox crashes or does not - how to fix

  If Firefox crashed, then please provide Crash ID here.

• SRV Win2k3 creating the new user at startup profile

  My Win2K3 Server creates a new user profile when starting, rather than use the existing account.
  For example, the account is called "USER"
  It creates a new profile named "USER. DOMAIN ".

  The "new USER. The DOMAIN profile"seems to have migrated all the parameters of the 'USER' profile, so that it is almost impossible to tell them apart.

  My problem is that this profile does not seem to be able to access the DHCP and DNS server (and other services) and the other server Win2K3, which is of the BDC.

  I tried to remove the disk from the machine and on another windows machine, remove the directory "USER. DOMAIN"and place it on a USB key. Then, turn the player on and start again. It just creates another "USER. The DOMAIN profile"again but this time that all parameters were also lost as if it created a whole new USER profile from scratch.

  I need to get her back to the original profile 'USER' to make everything functional again.

  I would also like to know how this happened and why, if someone wants to be good enough to explain it to me.

  Your help would be greatly appreciated.

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)

  *

  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum