Reliablity and performance monitor is empty

Similar Questions

• Reliability and performance monitor

  I use a Vista Home Premium based computer laptop HP.

  I find that I can access is no longer the reliability and performance monitor. When I try to access the report, I get the following message to come. Error: An error occurred trying to generate this report. The interface is unknown.

  I searched the internet, but have not been able to find a solution.

  I use a Vista Home Premium based computer laptop HP.

  I find that I can access is no longer the reliability and performance monitor. When I try to access the report, I get the following message to come. Error: An error occurred trying to generate this report. The interface is unknown.

  I searched the internet, but have not been able to find a solution.

  I know how to solve this problem

  Try this:

  go to the reliability and performance monitor, then in the section reports on the left, click system diagnostics then delete all generated reports (click on each and then delete) in there, then try to generate the new report.

  the reason for this error is that you have canceled or closed the report while he produced it!

  I hope this helps!

• In the reliability and performance monitor, under the health report there is a list for admission to the status of "device... *" gradient?

  Under above: to Win32_PnPEntity.DeviceID="Root\\Legacy_ (here 30 different names of devices or software corresponding names such as HTTP, ELRAWDISK, DXGKRNL, CRDISK, CLFS, AFD, KSECDD, LLTDIO, MOUNTMGR,... and others) followed by two backslashes after each name following the above endpoint and the underscore, then 0000

  It is this indicating I did not currently the afformentioned device currently installed in an internall or the outside slot, and thus the device/componet or software, that these elements are related is noted as "degraded state? This part of the report refers to a device or a pice of software? A device driver or utility?

  Thanks in advance everyone or Sir/Madam.

  I use a dell xps 630i, with vista 64-bit running to me excellent.

  Hi ThomasArney Jr,

  This can happen due to a hard drive which is a failure. You can try to run a Checkdsk and check if it helps.

  Note: When you run the disk check, there are chances of losing data if you can take a backup before starting the checkdisk.

  Check your hard drive for errors

  Hope this information is useful.

• What to do with the diagnostic results for "reliability and Performance.

  My lap top turns very slowly, hold stop in batch programs!

  I'm probably 80% computer illiterate, but I ran a "reliability and Performance Diagnostics" which came with 3 error warning.
  I don't know what to do with these results! He suggested that to determine if I use the devices and to varify the correct driver is installed! ???
  Help me please I'm fooled

  Goto http://support.microsoft.com/gp/mats#tab0 and choose
  Hardware devices not detected or does not

  In the future writein proper English with exact text of messages.

  --
  ..
  --
  "BeeBeeH" wrote in message news: 975ce200-2472-4423-8130-17088ed4dc46...
  > 2 say peripheral is disabled and to establish if the device is still necessary.
  > and the third says that the device has a configuration problem and that I should
  > check that the correct driver is installed.
  >
  >
  >
  >

• Error diagnostic system (resources and performance monitor) - conflict of property values

  Get error message "property a conflict of values" which attempt to run System Diagnostics.

  Looks like you may have a virus or other malware.  Try to start safe mode and run your anti-virus program to make a complete analysis of the system.  There are a number of suggestions along this line to the position of moderator of the forum Keith

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-performance/Windows-Explorer-has-stopped-working/6ab02526-5071-4DCC-895F-d90202bad8b3

  If none of this helps you run SFC/scannow from the command prompt in administrator mode.

  I hope this helps.  Good luck.

• Source and program monitors are empty

  I'm editing in cs5 PP and it was fine until yesterday when my monitors ceased to display my images. IM using on a NEW asus laptop so I don't know what it is or why all of a sudden he decided to not work. I have restarted my PC, reinstalled cs5 and its still the same thing. I'm working on a core i7, 8 GB ram with nvidia geforece card, so I'm lost. Any ideas?

  Also when I double click in the program monitor the image of the clip on the timeline will be displayed but I don't rub it in real time. the audio will be still played on two screens, but not the video. I also installed quicktime. Im having is not this problem on my desktop either.

  Thank you!

  Try the system restore to see if a recent update is the cause.

• Laptop HP OMEN - 15-J9K19UA: Omen Ops Central and performance HP monitor

  HP Performance Advisor is part of the Suite of the Ops Central HP OMEN; Since the last update (Performace Advisor. 1.8.7826.0), it is no longer present in the suite. Is there a procedure/process to add later in the Ops Central?

  

  Hi D5GR

  Thanks for the reply.

  Analyzer Performance HP automatically updated on execution and do not seem to have a setting to disable the upgrade.

  For this reason, restoration is not an option, it would just upgrade on the first run.

  Also, I don't see the problem here as being the performance Analyzer, but subsequently OMEN Ops Central. The configuration file now points to the wrong directory for the advisor.exe. Why the config is not editable by the end user? Or the continuation of the Ops Central needs a config file to reflect the new location.

  Center Ops Suite config

  LNK0018 = c: Program Files (x 86) \Hewlett-Packard\HP Performance Advisor\Advisor.exe
  APP0018 = HP Performance Advisor
  ARG0018 =
  ICO0018 = c: Program Files (x 86) \Hewlett-Packard\HP Performance Advisor\Advisor.exe
  TIP0018 = Item0318
  RPL0018 =

  Actual location now of performance monitor

  C:\Program Files (x 86) \Hp\HP Performance Advisor\Advisor.exe

  Update 09/07/15:

  I actually solved this first remove the attrbute the Hewlett-Packard folder read-only, and copy the complete HP Performance Advisor file from the HP folder to this location. The icon shows now and the app works very well from there.

  

• _ "Boot Performance Monitoring" and "stop Performance Monitoring. __

  I just looked to the top of the page "Event Viewer" and discovered 1 791 itemsmarked as 'endangered', 'Critical', 'Error', etc, etc, etc.!
  They seem to be linked to "Boot Performance Monitoring" and "Stop Performance Monitoring", etc., etc., etc..!
  How can I fix all of these issues, please?
  I have a little trouble with my home computer private.
  Whenever I turn on my PC, it takes a long time to start (is that what you call "Booting"?).
  Also, when I want to turn my PC off, it takes a long time to close.
  I tried a few computer maintenance such as: -.
  CLEANING DISC,
  THE FRAGMENTATION OF THE DISK,
  etc.,.
  but they have not alleviated the problems at all.
  Can someone help me with this please?
  Any assistance, information, suggestions, etc. would be greatly appreciated.
  Thanks !
  
  Alan Merrington
  E-mail address is removed from the privacy *.

  Hello

  Normally how long will it take to start a power off of the State? How long does take for
  Stop for a shutdown of the State?

  Use this simple free utility to read these events and it makes it easier to paste them into one
  message here. Do these after the SFC and CheckDisk as below.

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
  Set it for a bit before and after the time of the BSOD.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  ==========================================================

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================================

  Keep these practice to check possible error messages if they return.

  Check out these utilities to see if information may be collected:

  It is an excellent tool for displaying the blue screen error information

  -Free - BlueScreenView scans all your minidump files created during "blue screen of death," collisions
  and displays information about all accidents of a table.
  http://www.NirSoft.NET/utils/blue_screen_view.html

  -------------

  MyEventViewer can be verified at the time of the blue screen (BSOD) within a second or so of the
  time of the BSOD to provide more information about the possible cause - see TIP)

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
  Set it for a bit before and after the time of the BSOD.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  ------------

  AppCrashView - free - a small utility for Windows Vista and Windows 7 that displays the details of all the
  application goes down has occurred in your system. The information breaks down is extracted from the .wer
  the files created by the Windows Error Reporting (WER) of the operating system component of each
  time that an accident has occurred. AppCrashView also allows you to easily record the list of accidents to
  text/html/csv/xml file.
  http://www.NirSoft.NET/utils/app_crash_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Monitor is empty and the keys have no effect on anything.

  Monitor is empty and the keys have no effect on anything.

  With the computer off, I disconnected the power and removed the battery.

  Then I pressed the button On and connected to the power supply.

  The battery light and the touchpad light began to Flash.

  Then I turned off the computer and insert the battery.

  Then I turned on the computer and it began to emit beeps, 1 long and 2 short beeps.

  Thanks SeanS

  I was finally able to run.

  With the battery removed, I plugged the power supply and any of the top row of lights came. I pressed the power button until all lights are off. I then pressed the power button and started pressing on and releasing, pressing on and releasing, pressing and releasing, etc key F8 for about 10 seconds, and then the computer started to operate normally.

  DaMar

• What is the name of the performance monitor on Vista Home Premium

  I take a class of Microsoft and need to use performance monitor.  Running Vista Home Premium.  Cannot find the program.

  In the search box, type perf. He will appear as the Analyzer for performance and reliability. Until it clicks.

• Performance monitor reports OS check failure

  A few days ago Norton IS (to date) has reported that it had prevented a Trojan attack. I ran Norton Power Eraser and removed the Trojan horse. Also ran Malware Bytes it didn't report any problems.

  However, since then, I noticed some strange things.

  1. the performance reports monitor produces virus - anti but Norton is short. Have seen other posts of this topic and that it does not cause a problem, I'm happy wait for the fix fully tested in next SP.

  2. performance monitor reports also under alltests OS checks failed, version OS check Failed.

  3. I tried to run Fix IT for a similar sounding problem and get the message in case of problem cannot continue because an error has occurred. Download the utility for troubleshooting and enforcement it detects no problem.

  4. Furthermore, in performance under traceptHeader monitor, I get this message "the WMI class data service is not available.

  5. I tried to run restore but that crashes after it restarts.

  6 folder Admin Tools proved to be empty, but which were fixed by downloading a new set of tools.

  I presume that the Trojan horse did some damage before he was eliminated.

  It is better to repair Windows running or is there something else I need to do?

  Win 7 64 bit SP1 entirely up-to-date, Norton IS perfectly up-to-date.

  Thank you

  Derek

  Hello DerekNB,

  I thank you very much for the update on the question and sorry for delay acknowledgment.

  I really appreciate your efforts to solve the problem. It is worth noting that you have been able to determine the root cause and solved the problem. The steps that you updated will help other members of the community to solve similar problems.

  In addition to this, feel free to answer in the case where you are facing in the future other problems with Windows. We will be happy to help you again.

  Kind regards.

• Performance monitor

  I'm under 'Vista Home Premium' and would like to know how to use the performance monitor "" I want to know what I'm looking at everything including how to use it for what it is. Where do you suggest I learn such things or can you help me set up to help me learn.

  I'm under 'Vista Home Premium' and would like to know how to use the performance monitor "" I want to know what I'm looking at everything including how to use it for what it is. Where do you suggest I learn such things or can you help me set up to help me learn.

  I don't know anything about this topic.

  Here is a link that describes briefly what it is, with a freeware download:
  http://www.hexagora.com/en_dw_davperf.asp

  You may want to google for more information. For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• PC Cleaner performance monitor is the problem

  PC Cleaner performance monitor is the problem.

  PC Cleaner performance monitor is the problem.

  Yes, it may well be the source of any problems you encounter.

  In the future, don't be afraid to create a post long and detailed of what is or is not happening.

  This isn't twitter.

  My crystal ball suggests;

  First try Malwarebytes running to see if it can clean this software your system - rogue

  http://www.Malwarebytes.org/free/

  The information contained in the links below can also help.

  http://www.ehow.com/how_6075648_remove-PC-cleaner-virus.html

• How do you get performance monitor logs

  I want to access my system performance monitor logs, but cannot put them. I tried to register ' perfmon/sys' in the bottom search box, when I click on the Windows Start button. The magnifying glass search box disappears and an "X" appears in the bottom search box. I've never had this problem before.  What I am doing wrong?

  I want to access my system performance monitor logs, but cannot put them. I tried to register ' perfmon/sys' in the bottom search box, when I click on the Windows Start button. The magnifying glass search box disappears and an "X" appears in the bottom search box. I've never had this problem before.  What I am doing wrong?

  Click Start, click in the Search box, type perfmon.msc , and then press ENTER.

• Performance monitor of PeopleSoft on 8.52

  Hello
  
  I installed the tools 8.52.12 on a Windows Server 2008 with a DB only tools residing on a DB Oracle 11 GR 2 (64-bit) Windows. I try to activate the mode of self-monitoring and we tried everything to my knowledge.
  
  Accumulates the monitorsrv.log file with the following line:
  PSMONITORSRV.11964 (0) [17/01/13 17:56:09] (2) (PERFJNI): thrown Java exception: java.lang.NullPointerException
  
  
  In the APPSRV.log file the following text is displayed:
  PSAPPSRV.20524 [17/01/13 17:53:34] (2) (Agent of PerfMon) ID:16 successfully registered
  ....
  PSAPPSRV.20524 [17/01/13 17:53:54] (2) (Agent of PerfMon) Communication to the Servlet monitor failed. Performance monitor URL is not valid or the Web server performance monitor is not available. Exception: java.io.FileNotFoundException: http://ppm .***:80/monitor/perfmon//16
  PSAPPSRV.20524 [17/01/13 17:53:54] (2) (Agent of PerfMon) Data Transmission failed and so a new attempt to one more time
  PSAPPSRV.20524 [17/01/13 17:53:54] (2) (Agent of PerfMon) data transmit retry failed and therefore renounce
  
  
  In the PPMTRACE.log, it shows that the data sometimes send successfully
  PSAPPSRV.20524 [17/01/13 17:56:44] (2) (Agent of PerfMon) 16: 8 sending objects (~ 576 bytes)
  PSAPPSRV.20524 [17/01/13 17:56:44] (2) (Agent of PerfMon) 16: Communication to the Servlet monitor has failed. Exception: java.io.FileNotFoundException: http://ppm .***:80/monitor/perfmon//16
  PSAPPSRV.20524 [17/01/13 17:56:44] (2) (Agent of PerfMon) registration failed: http://ppm .***:80/monitor/perfmon//16
  PSAPPSRV.20524 [17/01/13 17:56:44] (2) (Agent of PerfMon) running sampler...
  PSAPPSRV.20524 [17/01/13 17:56:44] (2) (Agent of PerfMon) 16: data transmit retry failed and so abandon: java.io.FileNotFoundException: http://ppm .***:80/monitor/perfmon//16
  PSAPPSRV.20524 [17/01/13 17:56:44] (2) (Agent of PerfMon) running sampler...
  
  
  
  The Web server records the same questions:
  >
  # < 17 January 2013 18:11:56 CAT > < error > < ServletContext - > < PPM > < PIA > < thread-126 > < < anonymous > > <>< d5230bef27846b31:1e280481:13c490fce3b: - 8000-000000000000087 c > < 1358439116548 > < BEA-000000 > < PPMIClient 81913616269409 is unreachable. Give up to...
  java.net.ConnectException: connection refused: connect
  at java.net.PlainSocketImpl.socketConnect (Native Method)
  at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:351)
  at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:213)
  at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:200)
  at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366)
  at java.net.Socket.connect(Socket.java:529)
  at java.net.Socket.connect(Socket.java:478)
  at sun.net.NetworkClient.doConnect(NetworkClient.java:163)
  at psft.pt8.pshttp.http.HttpClient.openServer(HttpClient.java:378)
  at psft.pt8.pshttp.http.HttpClient.openServer(HttpClient.java:549)
  to psft.pt8.pshttp.http.HttpClient. < init > (HttpClient.java:316)
  to psft.pt8.pshttp.http.HttpClient. < init > (HttpClient.java:326)
  at psft.pt8.pshttp.http.HttpClient.New(HttpClient.java:338)
  at psft.pt8.pshttp.http.HttpURLConnection.connect(HttpURLConnection.java:451)
  at psft.pt8.pshttp.http.HttpURLConnection.getOutputStream(HttpURLConnection.java:498)
  at psft.pt8.pshttp.PSHttp.createOutputStream(PSHttp.java:354)
  at psft.pt8.pshttp.PSHttp.send(PSHttp.java:344)
  at com.peoplesoft.pt.ppm.monitor.PPMIClient._transmit(PPMIClient.java:225)
  at com.peoplesoft.pt.ppm.monitor.PPMIClient.transmit(PPMIClient.java:187)
  at com.peoplesoft.pt.ppm.monitor.PPMIClient.run(PPMIClient.java:166)
  at java.lang.Thread.run(Thread.java:662)
  >
  # < 17 January 2013 18:11:57 CAT > < error > < ServletContext - > < PPM > < PIA > < thread-24 > < < anonymous > > <>< d5230bef27846b31:1e280481:13c490fce3b: - 8000-0000000000000021 > < 1358439117441 > < BEA-000000 > < Communication to the Servlet monitor has failed. Performance monitor URL is not valid or the Web server performance monitor is not available.
  java.io.FileNotFoundException: http://ppm *: 80/monitor/perfmon / / 20
  at psft.pt8.pshttp.http.HttpURLConnection.getInputStream(HttpURLConnection.java:621)
  at java.net.HttpURLConnection.getResponseCode(HttpURLConnection.java:379)
  at psft.pt8.pshttp.PSHttp.getResponseCode(PSHttp.java:379)
  at com.peoplesoft.pt.ppm.agent.Network.sendObject(Network.java:132)
  at com.peoplesoft.pt.ppm.agent.Agent.flushBuffer(Agent.java:535)
  at com.peoplesoft.pt.ppm.agent.Agent.run(Agent.java:429)
  at java.lang.Thread.run(Thread.java:662)
  >
  
  
  
  I missed to set something up?
  
  Edited by: Andrew du Plessis on January 30, 2013 05:16

  Hello

  Try this. The addition of port to the app server config. I had the same error as you, and it is resolved after the addition of port

  ;=========================================================================
  ; PSPPMSRV settings
  ;=========================================================================

  ;-------------------------------------------------------------------------
  ; UBBGEN settings
  ; As Gatherer performance do not advertise services Max and Min
  ; Instances must always be equal
  Instances of min = 3
  Instances of max = 3

  listening_port = 65000