Remote access VPN integration with RSA token
Hello friends,
I currently have an ASA 5520 9.0 focusing distance french authenticated VPN access a Radius of the ACS server. I also have a server ACS Ganymede + allowing to authenticate access to network devices (routers, switches, etc.). My Manager asked me to include a second level of authentication through RSA token´s. Question´s:
How does it work?
Can I use my ACS Ganymede + as a method of redundancy for authentication of the VPN´s in the case where my Radius server goes down?
I can use my ACS server RADIUS as a method for redundancy for managing my network devices in the case of authentication my Ganymede + server goes down?
In addition, the RSA token can be used to authenticate access to manage network devices?
Any comments will be appreciated.
Kind regards!
RSA has built in the radius server and itself it can serve as a factor of two.
using Token RSA server inside itself is two factor when you use a PIN and access code.
Using of Ganymede + for VPN is not possible.
Check with your administrator RSA for the integration steps.
Is that you can directly integrate the ASA with RSA and integrate with RSA ACS as well.
This way you have redundancy in the RSA server.
http://www.Cisco.com/c/en/us/support/docs/security/secure-access-control...
http://www.Cisco.com/c/en/us/support/docs/security-VPN/SecureID-SDI/1163...
Rate if useful :)
Knowledge sharing makes you immortal.
Kind regards
Ed
Tags: Cisco Security
Similar Questions
-
Problem with remote access VPN
Hello
I installed a remote access VPN on my firewall ASA5505 via the ASDM Assistant.
I can successfully connect with the Cisco VPN client. My firewall also shows me the VPN session and shows the Rx packets. However, Tx packets remain 0, so no traffic is getting out. My ASA5505 is configured as a router on a stick with 25 different VLAN. I want to restrict traffic to one VLAN specific using a card encryption.
When I run a command to ping t on my connected Windows box, the firewall log shows me the following message:
"Unable to find political IKE initiator: outside Intf, Src: 10.7.11.18, Dst: ' 172.16.1.1
"This message indicates that the fast path IPSec processing a packet that triggered of IKE, but IKE policy research has failed. This error could be associated calendar. The ACL triggering IKE could have been deleted before IKE has processed the request for initiation. "This problem will likely correct itself."
Unfortunately, the problem is correct.
The "sh cry isa his" and "sh cry ips its ' commands show the following output:
2 IKE peers: 62.140.137.99
Type: user role: answering machine
Generate a new key: no State: AM_ACTIVE
Interface: outside
Tag crypto map: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: 85.17.xxx.xxx (outside interface IP)
local ident (addr, mask, prot, port): (0.0.0.0/0.0.0.0/0/0)
Remote ident (addr, mask, prot, port): (172.16.1.1/255.255.255.255/0/0)
current_peer: 62.140.137.99, username: eclipsevpn
dynamic allocated peer ip: 172.16.1.1
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 4351, #pkts decrypt: 4351, #pkts check: 4351
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0
success #frag before: 0, failures before #frag: 0, #fragments created: 0
Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
#send errors: 0, #recv errors: 0
local crypto endpt. : 85.17.xxx.xxx/4500, remote Start crypto. : 62.140.137.99/3698
Path mtu 1500, fresh ipsec generals 82, media, mtu 1500
current outbound SPI: B3D60F71
current inbound SPI: B89BA14A
SAS of the esp on arrival:
SPI: 0xB89BA14A (3097207114)
transform: aes - esp esp-sha-hmac no compression
running parameters = {RA, Tunnel, NAT-T program,}
slot: 0, id_conn: 196608, crypto-card: SYSTEM_DEFAULT_CRYPTO_MAP
calendar of his: service life remaining key (s): 25126
Size IV: 16 bytes
support for replay detection: Y
Anti-replay bitmap:
0xFFE1FFF8 0xFFFFFFFF
outgoing esp sas:
SPI: 0xB3D60F71 (3017150321)
transform: aes - esp esp-sha-hmac no compression
running parameters = {RA, Tunnel, NAT-T program,}
slot: 0, id_conn: 196608, crypto-card: SYSTEM_DEFAULT_CRYPTO_MAP
calendar of his: service life remaining key (s): 25126
Size IV: 16 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001
I really have no idea what's going on. I installed a remote access VPN countless times, but this time it shows me the error as described above.
Hi Martijn,
just a few quick thoughts:
-is your ok NAT exemption, i.e. ensure that the return traffic is not NAT' ed.
-Make sure that there is no overlap crypto ACL
-When connected, make a package tracer to see what is happening with the return packages.
for example
packet-tracer in the interface within the icmp 10.7.11.18 0 0 172.16.1.1 detail
(where is the name of the interface on which 10.7.11.18 resides)
This will show you all the steps the rail package in-house (routing, nat, encryption etc.) so it should give you an idea of what is happening, for example when it comes to the bad interface, nat evil rule, wrong entry card crypto etc.
HTH
Herbert
-
Remote access VPN with ASA 5510 by using the DHCP server
Hello
Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?
I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:
!
ASA Version 8.2 (5)
!
interface Ethernet0/1
nameif inside
security-level 100
IP 10.6.0.12 255.255.254.0
!
IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)
!
Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1
!
Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dyn1 1jeu transform-set FirstSet
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
mymap map crypto inside interface
crypto ISAKMP allow inside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
!
VPN-addr-assign aaa
VPN-addr-assign dhcp
!
internal group testgroup strategy
testgroup group policy attributes
DHCP-network-scope 10.6.192.1
enable IPSec-udp
IPSec-udp-port 10000
!
username testlay password * encrypted
!
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
strategy-group-by default testgroup
DHCP-server 10.6.20.3
testgroup group tunnel ipsec-attributes
pre-shared key *.
!
I got following output when I test connect to the ASA with Cisco VPN client 5.0
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO
4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: Group = testgroup, I
[OK]
KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable
Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes
Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!
Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address
Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048)
, : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740)
, : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80
Kind regards
Lay
For the RADIUS, you need a definition of server-aaa:
Protocol AAA - NPS RADIUS server RADIUS
AAA-server RADIUS NPS (inside) host 10.10.18.12
key *.
authentication port 1812
accounting-port 1813
and tell your tunnel-group for this server:
General-attributes of VPN Tunnel-group
Group-NPS LOCAL RADIUS authentication server
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
Cisco Asa 5505 and level 3 with remote access VPN switch
Today I had a new CISCO LAYER 3 switch... So here's my scenrio
Cisco Asa 5505
I have
Outside of the == 155.155.155.x
Inside = 192.168.7.1
Address POOL VPN = 10.10.10.1 - 10.10.10.20
3 layer switch configuration
VLAN 2
ip address of the interface = 192.168.1.1
VLAN 2
ip address of the interface = 192.168.2.1
VLAN 2
ip address of 192.168.3.1 = interface
VLAN 2
ip address of the interface = 192.168.4.1
VLAN 2
ip address of the interface = 192.168.5.1
IP Routing
So I want the customers of my remote access VPN to access all that these networks. So please can you give me a useful tip or a link to set up the rest of my trip
Thanks to you all
Al ready has responded
Sent by Cisco Support technique iPad App
-
Remote access VPN user permission
Hi support them.
It is a way for a remote access VPN to allow some users access to "Host A, B, C" and other users to access hosts D, E, F? Basically, we want to have some users have access at home to a few servers and other users have access only to some other servers. Is this possible without a GANYMEDE or some other device? Thank you guys!
Hi John,.
Yes, you can configure split tunneling to allow a specific group of users access to specific hosts.
How this is achieved, it is that you create a connection profile different for different users, associate a policy group and the title of each group policy, you have a split tunnelling access-list defined with entries of different hosts.You must create 2 profiles of connection here and match them with 2-group policy allowing access to 2 differernt resources (they can be multiple as well)
Here is a reference document: -.
Kind regards
Dinesh MoudgilPS Please rate helpful messages.
-
Hi all
I need help with remote access vpn configuration. I want to some remote users who have access to the internet on their system to connect and access an application server in my seat social cisco vpn client user. I use Cisco 881. I am unable to use the SDM configuration because it seems that SDM is not supported by the router so I'm using command line. I'd appreciate any help I can get. Thank you.
This is the configuration I have:
VPNROUT #sho run
Building configuration...Current configuration: 6832 bytes
!
! Last configuration change at 10:50:45 UTC Saturday, May 30, 2015, by thomas
version 15.2
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname VPNROUT
!
boot-start-marker
boot-end-marker
!
!
logging buffered 51200 warnings
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login userauthen1 local
AAA authorization groupauthor1 LAN
!
!
!
!
!
AAA - the id of the joint session
iomem 10 memory size
!
Crypto pki trustpoint TP-self-signed-1632305899
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 1632305899
revocation checking no
rsakeypair TP-self-signed-1632305899
!
!
TP-self-signed-1632305899 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
69666963 31363332 33303538 6174652D 3939301E 170 3134 30313233 31323132
33325A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 36333233 65642D
30353839 3930819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
8100BC0C 341CD79B A38572CE 1F0F9A91 F96B133C A889B564 E8352034 1CF5EE4B
B505616B 6014041B EC498C0A F6C5CD2B F5BF62DA BD6E1C44 0C7B9089 1FD0C6E5
299CEB40 28CD3F3B ADE3468A B07AAA9F AC42F0A7 4087172A 33C4013D 9A50884D
5778727E 53A4940E 6E622460 560C F597DD53 3B 261584 E45E8776 A848B73D 5252
92 50203 010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355 D
551 2304 18301680 14E85AD0 DEF133D8 E09516FD 0AA5FDAD E10EAB1A FA301D06
03551D0E E85AD0DE 04160414 F133D8E0 9516FD0A A5FDADE1 0EAB1AFA 300 D 0609
2A 864886 818100A 5 05050003 5B23ED5B 9A380E1F 467ABB03 BAB1070B F70D0101
7A 218377 73089DC1 D32DA585 C5FD7ECE 0D000F96 7F3AB6CC 71509E8F 3F1C55AE
E37536A3 1008FBF9 A29329D5 6F76DDC0 AA1C70AE 958AAE5D 32388BE4 2C1C6839
0369 D 533 027B612C 8D199C35 C008FE00 F7E1DF62 9C73E603 85C3240A 63611D 93
854A61E2 794F8EF5 DA535DCC B209DA
quit smoking
!
!
!
no record of conflict ip dhcp
DHCP excluded-address IP 10.10.10.1
DHCP excluded-address IP 172.20.0.1 172.20.0.50
!
DHCP IP CCP-pool
import all
Network 10.10.10.0 255.255.255.248
default router 10.10.10.1
Rental 2 0
!
IP dhcp pool 1
network 172.20.0.0 255.255.240.0
domain meogl.net
router by default - 172.20.0.1
172.20.0.4 DNS server 41.79.4.11 4.2.2.2 8.8.8.8
8 rental
!
!
!
no ip domain search
IP domain name meogl.net
name of the IP-server 172.20.0.4
name of the IP-server 41.79.4.11
IP-server names 4.2.2.2
8.8.8.8 IP name-server
IP cef
No ipv6 cef
!
!
license udi pid CISCO881-K9 sn FCZ1804C3SL
!
!
username secret privilege 15 thomas 4 JXSizd1r/hMqPpGz94vKBb5somtpZLy03k50rJvHO6c
username privilege 15 secret 4 mowe hlfv/rdDRCAeTUzRXbOIfdaKhJCl1onoGdaQeaQsAnw
!
!
!
!
!
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group moweclients
XXXXXXX key
DNS 172.20.0.4
meogl.net field
pool mowepool
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac moweset
tunnel mode
!
!
!
Dynmap crypto dynamic-map 1
Set transform-set moweset
market arriere-route
!
!
card crypto client mowemap of authentication list userauthen1
card crypto isakmp authorization list groupauthor1 mowemap
client configuration address card crypto mowemap answer
mowemap 1 card crypto ipsec-isakmp dynamic dynmap
!
!
!
!
!
interface Loopback0
IP 172.30.30.1 255.255.255.0
IP nat inside
IP virtual-reassembly in
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
switchport access vlan 100
no ip address
!
interface FastEthernet3
no ip address
!
interface FastEthernet4
IP 41.7.8.13 255.255.255.252
NAT outside IP
IP virtual-reassembly in
intellectual property policy map route VPN-CLIENT
Shutdown
automatic duplex
automatic speed
mowemap card crypto
!
interface Vlan1
Description $ETH_LAN$
IP 10.10.10.1 255.255.255.248
IP tcp adjust-mss 1452
!
interface Vlan100
IP 172.20.0.1 255.255.240.0
IP nat inside
IP virtual-reassembly in
!
local pool IP 192.168.1.1 mowepool 192.168.1.100
IP forward-Protocol ND
IP http server
23 class IP http access
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP nat inside source overload map route interface FastEthernet4 LAT
IP route 0.0.0.0 0.0.0.0 41.7.8.12
!
access-list 23 allow 10.10.10.0 0.0.0.7
access-list 23 allow 172.20.0.0 0.0.15.255
access-list 100 permit ip 172.20.0.0 0.0.15.255 everything
access-list 144 allow ip 192.168.1.0 0.0.0.255 any
not run cdp
!
LAT route map permit 1
corresponds to the IP 100
IP 41.7.8.12 jump according to the value
!
route VPN-CLIENT map permit 1
corresponds to the IP 144
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
access-class 23 in
privilege level 15
transport input telnet ssh
line vty 5 15
access-class 23 in
privilege level 15
transport input telnet ssh
!
!
endPlease the configuration above, give me the desired output.
Thank you.
Hello Thomas,.
I'm glad to hear that you have found useful in the example configuration.
I checked your configuration and everything seems ok with him, especially the statements of nat.
ip local pool mowepool 192.168.1.1 192.168.1.100 access-list 100 deny ip 172.20.0.0 0.0.15.255 192.168.1.0 0.0.0.255 access-list 100 permit ip 172.20.0.0 0.0.15.255 any route-map LAT permit 1 match ip address 100 ip nat inside source route-map LAT interface FastEthernet4 overload interface Vlan100 ip address 172.20.0.1 255.255.240.0 ip nat inside ip virtual-reassembly in
Try to generate ICMP traffic behind your 100 VLANS to the client VPN in order to answer the following questions:
-The router receives this traffic between VLAN100 unit?
-The router is encrypt this traffic, after receiving the ICMP packet?
#show crypto ipsec router its can help you with this question. Look for the program/decaps counters.
-The same, but the other way around (from VPN client to device behind VLAN100) try to locate the problem.
The following document explains more this crypto commands and debugs if necessary.
-
PIX 515E and remote access VPN
I use a PIX 515E with: ASDM Version: 5,0000 51 PIX Version: 8.0 (4) and configure it with remote access VPN.
I would like to get an email every time that a user login (and or disconnection) to the VPN. Remote clients use the Cisco VPN Client.
Any help is appreciated,
Hello
Here is a link to the email configuration when you log in to the ASA/PIX: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc7
Then you can create a list of message to send the logs only for the connection/disconnection of the VPN user: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc18
There is a wire that is linked here: https://supportforums.cisco.com/discussion/10798976/asa-email-logging-issue
-
Remote access VPN fails after upgrading to 8.04
Hello:
Sorry if this has been posted, but I couldn't find it anywhere.
After the upgrade of my 2 of my 5510 s to 8.04, my remote access VPN does not work. I can connect via Radius without problem. Once connected, I can't do anything on the network. When I try to telnet to any device, I get a white screen with no response. As it is to find the device but it does not. E-mail, intranet, nothing works. Seems to be time. I tried to upgrade to the latest version of Windows Client, still no go.
Everyone knows this at all? Any help appreciated.
TIA,
Brad
I saw the same problem after upgrading to 8.0.4. And it is caused by the "IP Compression" option enabled in group policy. After deactivation, it works. Cisco has just completed this bug recently:
Zhenning
-
Remote access VPN pix version 8.0 (3)
Hi all
First of all, I would like to thank to all members of the forum who got help in several messages on the configuration of the pix 515.
I am now configuring remote VPN access with radius authentication to my network, but I can't connect.
I use the cisco vpn client 5.0.03.0560, I have also tested my pix radius (inside) server authentication and works very well.
I already tried to retype the key of the cli, but I still can't remote access vpn to work.
I also tried to create another remote vpn with another name and local authentication, but I have the same problem.
I use 8.0 (3) version pix.
Can someone help me
I attach the log file of the cisco vpn client to help solve the problem, as well a configuration of the pix folder.
Thank you very much in advance and I seek prior information.
http://www.Cisco.com/en/us/docs/security/ASA/asa72/configuration/guide/vpnadd.html#wp999516
[Pls RATE if HELP]
-
Remote access VPN group name and password
Hi guys,.
Can someone tell me please the command to display a remote access VPN group name and the password on a firewall version 8.0 of ASA? Any help will be greatly appreciated.
Thank you
Lake
Remote VPN IPsec IKEv1 access are listed as groups of tunnel. If you enter
more system:running-config | b tunnel-groupYou can see the config sections (starting with the first mention of the tunnel-group) as well as the pre-shared key ikev1 plaintext String.
-
Hello!
I have 9.1 (3) version of Cisco ASA with remote access VPN set UP on the outside interface. When the user connects to the Internet on the outside interface, it works well. My goal is to allow the connection of all other interfaces (inside the dmz and etc.) to the outside interface. Cisco ASA allows to do? Order to packet - trace output is less to:
MSK-hq-fw1 # packet - trace entry inside tcp 10.10.10.1 14214 1.1.1.2 443
Phase: 1
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
developed 1.1.1.2 255.255.255.255 identity
Phase: 2
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
developed 1.1.1.2 255.255.255.255 identity
Result:
input interface: inside
entry status: to the top
entry-line-status: to the top
the output interface: NP identity Ifc
the status of the output: to the top
output-line-status: to the top
Action: drop
Drop-reason: (headwall) No. road to host
Hello
Well, you can of course turn VPN on other interfaces, but to be honest, I never even tried to set up the VPN it otherwise than of multiple multiple external interfaces in the case of the ISP and in this case only for testing purposes.
Some things related to the ASA are well known but not well documented.
The official document that I can remember: this is the following (which only refers to this limitation regarding the ICMP)
Note
For security purposes the security appliance does not support far-end interface ping, that is pinging the IP address of the outside interface from the inside network.
Source (old configuration guide):
-Jouni
-
Remote access VPN without certificate
Hi all
I want to deploy remote access VPN to ASA using Cisco anyconnect version 5512 customer secure mobility 3.1.05152. However, it must be a valid certificate of a CA such as verisign, entrust...
Is - it there anyway that I can use the certificate auto-signer? Thank you for helping me!
Hi Harry,.
I think it would always be possible to configure the VPN just with simple authentication AAA.
In my opinion you just set up your client to check worthy of trust of the certificate installed on your ASA.
Please uncheck as on sccreenshot:
Thank you
Jan
-
We have 10 sites with ASA 5505 connected to the ASA 5510 of main office
through IPSec VPN tunnels. Home users connect to the main office network
using the remote access vpn connection. They can also connect to the ASA 5505
remote sites by vpn for remote access to the ASA 5510?
Thanks, please help!
Here's the PDF.
-
How to use ACS 5.2 to create a static ip address user for remote access VPN
Hi all
I have the problem. Please help me.
Initially, I use ACS 4.2 to create the static ip address for VPN remote access user, it's easy, configuration simply to the user defined > address assignment IP Client > assign the static IP address, but when I use ACS 5.2 I don't ' t know how to do.
I'm trying to add the IPv4 address attribute to the user to read "how to use 5.2 ACS", it says this:
1Ajouter step to attribute a static IP address to the user attribute dictionary internal:
Step 2select System Administration > Configuration > dictionaries > identity > internal users.
Step 3click create.
Static IP attribute by step 4Ajouter.
5selectionnez users and identity of the stage stores > internal identity stores > users.
6Click step create.
Step 7Edit static IP attribute of the user.
I just did, but this isn't a job. When I use EasyVPN client to connect to ASA 5520, user could the success of authentication but will not get the static IP I set up on internal users, so the tunnel put in place failed. I'm trying to configure a pool of IP on ASA for ACS users get the IP and customer EasyVPN allows you to connect with ASA, everything is OK, the user authenticates successed.but when I kill IP pool coufigurations and use the "add a static IP address to the user 'configurations, EzVPN are omitted.
so, what should I do, if anyboby knows how to use ACS 5.2 to create a user for ip address static for remote access VPN, to say please.
Wait for you answer, no question right or not, please answer, thank you.
There are a few extra steps to ensure that the static address defined for the user is returned in the Access-Accept. See the instuctions in the two slides attached
-
ASA 5505 - remote access VPN to access various internal networks
Hi all
A customer has an ASA 5505 with a remote access vpn. They are moving their internal network to a new regime and that you would be the users who come on the vpn to access the existing and new networks. Currently can only access the existing. When users connect to access remote vpn, the asa gave them the address 192.168.199.x. The current internal network is 200.190.1.x and that they would reach their new network of 10.120.110.x.
Here is the config:
:
ASA Version 8.2 (5)
!
ciscoasa hostname
enable encrypted password xxx
XXX encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 200.190.1.15 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address 255.255.255.0 xxxxxxx
!
exec banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED
connection of the banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED
banner asdm the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED
passive FTP mode
access extensive list ip 200.190.1.0 inside_access_in allow 255.255.255.0 any
outside_access_in list extended access permit icmp any external interface
access extensive list ip 192.168.199.0 outside_access_in allow 255.255.255.192 host 10.120.110.0
Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 200.190.1.0 255.255.255.0
MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0
access extensive list ip 200.190.1.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192
inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask 192.168.199.10 - 192.168.199.50 255.255.255.0 IP local pool Remote_IPSEC_VPN_Pool
IP verify reverse path to the outside interface
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 200.190.1.0 255.255.255.0
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 190.213.43.1 1
Route inside 10.120.110.0 255.255.255.0 200.190.1.50 1
Route inside 192.168.50.0 255.255.255.0 200.190.1.56 1
Route inside 192.168.60.0 255.255.255.0 200.190.1.56 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
http server enable 10443
http server idle-timeout 5
Server of http session-timeout 30
HTTP 200.190.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
Crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
(omitted)
quit smoking
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 3600
Telnet timeout 5
SSH 200.190.1.0 255.255.255.0 inside
SSH timeout 5
SSH version 2
Console timeout 5
dhcpd outside auto_config
!
a basic threat threat detection
scanning-threat shun threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
internal MD_SSL_Gp_Pol group strategy
attributes of Group Policy MD_SSL_Gp_Pol
VPN-tunnel-Protocol webvpn
WebVPN
list of URLS no
disable the port forward
hidden actions no
disable file entry
exploration of the disable files
disable the input URL
internal MD_IPSEC_Tun_Gp group strategy
attributes of Group Policy MD_IPSEC_Tun_Gp
value of banner welcome to remote VPN
VPN - connections 1
VPN-idle-timeout 5
Protocol-tunnel-VPN IPSec webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list MD_IPSEC_Tun_Gp_splitTunnelAcl
the address value Remote_IPSEC_VPN_Pool pools
WebVPN
value of the RDP URL-list
attributes of username (omitted)
VPN-group-policy MD_IPSEC_Tun_Gp
type of remote access service
type tunnel-group MD_SSL_Profile remote access
attributes global-tunnel-group MD_SSL_Profile
Group Policy - by default-MD_SSL_Gp_Pol
type tunnel-group MD_IPSEC_Tun_Gp remote access
attributes global-tunnel-group MD_IPSEC_Tun_Gp
address pool Remote_IPSEC_VPN_Pool
Group Policy - by default-MD_IPSEC_Tun_Gp
IPSec-attributes tunnel-group MD_IPSEC_Tun_Gp
pre-shared key *.
!
!
context of prompt hostname
: end
The following ACL and NAT exemption ACL split tunnel is incorrect:
MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0
inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192
It should have been:
Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 10.120.110.0 255.255.255.0
access extensive list ip 10.120.110.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192
Then 'clear xlate' and reconnect with the VPN Client.
Hope that helps.
Maybe you are looking for
-
Yesterday my Firefox has suddenly started showing strange boxes on different parts of each web page. For example, there are black boxes above the scroll bar. When displaying Facebook, there are small squares (black, gray, white) in the scroll bar, sm
-
Why welcome to tab toolbar Yahoo continue to flock to the top?
A few days ago a Yahoo toolbar updated for Firefox updated itself automatically installed. Even after numerous attempts to get rid of the toolbar, re - download and reinstall the toolbar and even get rid of Firefox and re-installing Firefox, welcome
-
access to internet iPhone 6 locked
my internet access is locked
-
Where can I find data, such as saved games, for applications like the pillars of eternity?
I looked at the support of the application, and there is no record of the application of the pillars of eternity. In fact, there is only the application itself, and opening "content" does not show a file parts stored. Any help will be appreciated.
-
Can't find the HP Support Assistant icon on taskbar!
I was using a HP Pavilion notebook g4-1024tx. He has been using Windows 7. HP Support Assistant version, I used is 7.0.39.17. Today, when I use my computer, he suddenly asked me to restart my computer. So, I closed all the windows of my and restarted