Remote LAN Internet access

Similar Questions

• How to configure the VPN LAN to access the internet from the remote network

  I have set up for our project site to another Office VPN. Please join.
  Now I have already configured Site to site vpn between ASA 5510 and 1841 router.

  HQ LAN

  Branch of the LAN
                   10.2.1.0/24 > ASA 5510 1841 > > INTERNET < 1841=""> <> 10.30.3.0/24
  ^
  ^
  ^
  ^
  Call Manager
  No. 2851
  Now access from branch LAN LAN of HQ each other.

  I face problems that are
  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH
  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?
  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  Please give advise me how should I do.

  Hello

  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH

  Answer:

  You must configure the NAT and crossed to the ASA HQ so that the VPN branch router provides LAN and u-Turn, access to Internet of the SAA.  You must first seup NAT for the branch on the SAA router subnet, then you must type the command:

  permit same-security-traffic intra-interface

  Here's a great example for VPN client hairpining.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?

  Yes, you can

  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  You must change your subnet VLANS to be different from the subnet HQ voice phone IP VOice VLAn, it should be fine.

  Kind regards

  Mohamed

• Cannot access a remote LAN with Cisco Client

  Hello

  IAM using an ASA 5505 and connect with the Cisco Client 5.0.02.0090. The Client connects to the Remote LAN and get an IP of the SAA.

  But I can't access the Remote LAN or ping the Interface of the ASA trainee.

  Can someone help me with this problem?

  If the client computer is in the same subnet as the other PC, then its dislikes a question ASA.

  Just make sure that the client computer is in the subnet, default gateway of 192.168.20.100 192.168.20./24 and connected to a switchport on vlan 1.

  Finally, check whether the DNS resolution works, or if you can browse the internet with the ip address.

• I installed in my laptop XP - SP3 PersonalFirewall of Privacyware and I have this problem: when restarting, always internet access isn't available (WiFi/LAN).

  network adapter AutoDetect fails

  Hello:

  I installed in my laptop XP - SP3 PersonalFirewall of Privacyware and I have this problem: when restarting, always internet access isn't available (WiFi/LAN).
  Using the command ipconfig, I found that these cards are not detected. (Although without wireless/LAN icons do not display the modem connection). Also, if I go into Device Manager, I see network cards. BUT if I select "research material changes", then the other adapters will appear (those of Privacyware) and internet connection is reset and it will work then.  I wonder why windows does not detect this kind of cards automatically when I start it.

  This problem occurs only in my laptop - I installed the project Feederwatch on a laptop another XP and it worked, so Privacyware cannot provide a solution, since seems a very specific problem.

  Thanks for any idea!

  Seems that the solution was:

  1 - Open Device manager and view the hidden devices.
  2. then go into not connectable & play devices and manually delete all the remainers network software & security uninstalled (process antivirus, firewall, monitor).
  3. several reboots were required in order to know if the garbage problem has been removed.

• RVL200 SSL VPN: cannot access a remote LAN with iPad2

  RVL200 firmware 1.1.12.1

  iPad2 cannot access any device on the Remote LAN despite the closed padlock icon.

  Is there another App needed? Or how to debug SSL VPN?

  Emmanuel,

  Were you able to access the LAN devices? Also, have you connected using a Mac or a PC successfully to verify that the devices are available? Sometimes antivirus and firewall software can block access to devices from a remote IP address.

• No Internet access in guest, but don't have LAN access

  VMware virtual server 2 =

  Host = Windows 7

  Comments = Windows Vista

  Virtual network = bridge

  Can access LAN.

  Can even ping Google.com and cmd nslookup google.com

  But... IE browser gets no Internet access.

  Any ideas?

  Thank you!

  Welcome to the community,

  This looks like a firewall or a problem AV. try to temporarily disable any AV and firewall on the Windows 7 host.

  André

• LAN/Ethernet and wireless: can connect to networks, but shows "no Internet access.

  My workplace has cable/Ethernet and Wi - Fi.  I'm working on a laptop, plug it into a dock where my ethernet cable is connected.  Lately, I've been the startup object and the network will connect automatically (by default to connect to the local network, not for the wireless) but I get the point of the triangle/yellow exclamation on my network icon and displays "no Internet access.  Even if I get this warning message /, in fact, I can access the internet, but I can't access resources online through a program installed (such as, to access to the / insertion of a photo online by word or update a SharePoint Outlook calendar).

  In the past, I could connect wirelessly and work around this problem.  However, now my wireless connection does the same thing: it will connect, it displays the warning "no access Internet, I can access the internet, but not another program."

  I ran the resolution of problems and it does not identify the problem.  I've updated drivers, disconnected and reconnected networks - nothing seems to work.  Any ideas?

  Given that you encounter this work to your work network you really need to get your business COMPUTER Department to come and watch. As far as we know, there may be certain restrictions checked in your network permissions that must not checked. There is so much that can happen it is impossible to diagnose on an online forum.

• Internet access computer looking for a dialup connection everytime I try to log

  Original title: Internet access

  Why my computer is looking for a remote connection everytime I try to log in?  All my computers are connected to the DSL.  I get this window pop up on two of my computers and I have to click on connection settings and check the LAN to connect properly.

  Hello

  1. what version of Windows are you using?

  2 have you made changes on the computer before this problem?

  I suggest you try this method and check the status of the issue.

  To stop, start Internet Explorer (canceling any attempt to compose on the road):

  (a) open Internet Explorer.

  (b) click on the Tools menu

  (c) click on the Internet Options menu item

  (d) click the connections tab

  (e) check the never connect.

  You can also check:

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• How can I get Vista "Windows Mail" to check mail using my connection local (LAN) internet?

  How can I get Vista "Windows Mail" to check mail using my connection local (LAN) internet?

  It allows only wants to "connect" using dial-up, wireless or wired ISP (type PPP) requiring a UID and password, of which none seem to allow me to select a LAN (ISP) simple (without a password).

  I know that the Ethernet connection works Ok, because I can use it with a standard Web browser; only the mail tool can't seem to see or use.

  Whenever I tell the Windows Mail email 'Send and receive', he wants to 'connect' for remote access or one of his three choices (listed above and direct exclusion of any connection to the local network).  It works with remote access, so once I have spend that I should be Ok. but I can't make it work directly.

  Help.

  In Windows Mail, go to select Tools, accounts, your account email, properties, connection.  It shows for the connection?  You
  should leave this setting not selected, in which case Windows Mail will use the IE connection uses.
   
  In addition, under Tools, Options, connection, the first checkbox must be checked, and the second box unchecked.
   
  If everything which withdraws, but you still have the problem, the account may be damaged.  Remove account, restart Windows Mail,.
  then recreate the account.
   
  Gary van, Microsoft MVP (Mail)
  ------------------------------------------------------
   
  "W6NCT" wrote in the new message: * e-mail address is removed from the privacy... *
   
  How can I get Vista "Windows Mail" to check mail using my connection local (LAN) internet?
   
  They don't allow that wants to "connect" using dial-up, wireless or wired ISP (type PPP) requiring a UID and password.
  which none seems to allow me to select a LAN (ISP) simple (without a password).
   
  I know that the Ethernet connection works Ok, because I can use it with a standard Web browser; is not only the messaging tool
  to see or use.
   
  Whenever I tell the Windows Mail email 'Send and receive', he wants to "connect" to remote access or one of his three choices (listed
  above and to the exclusion of any direct connection to the local network).  It works with remote access, so once I have spend that I should be Ok. but I just
  cannot operate directly.
   
  Help.
   
   

  Gary van, Microsoft MVP (Mail)

• EZVPN nem - Internet access mode

  Hello

  I have a router cisco 881 and an asa 5520 SW 8.4

  I configured EZVPN NEM mode between the router ASA and 881.  However the 881 can access network resources on the inside interface of the ASA, where it ends.  However the site using the 881 cannot access the internet.  I know that I could configure split tunnel and the site would use only the tunnel for our internal network (10.0.0.0).  However, I want this site to our ASA allows access to the internet so that the restrictions will apply to this site too.  I apologize in advance if I have not provided enough information.

  Router config 881 is lower, ASA config is too big to post, but if you tell me what exactly you want I post, I will;

  no ip domain search

  "yourdomain.com" of the IP domain name

  IP cef

  No ipv6 cef

  !

  license udi pid CISCO881-K9 sn FCZ17219082

  !

  username secret privilege 15 netadmin 4 N2rcMRAZjsOjF7Kp/KUkH4cfBtBYp.1Cc.V8E0utmSI

  !

  Crypto ipsec client ezvpn EZVPN

  connect auto

  Group TG_EZVPN key ourkey

  network extension mode

  peer FIREWALL IP

  username password user password

  xauth userid local mode

  !

  !

  !

  !

  !

  interface FastEthernet0

  no ip address

  !

  interface FastEthernet1

  no ip address

  !

  interface FastEthernet2

  no ip address

  !

  interface FastEthernet3

  no ip address

  !

  interface FastEthernet4

  Description * Interface Outside *.

  DHCP IP address

  automatic duplex

  automatic speed

  Crypto ipsec client ezvpn EZVPN

  !

  interface Vlan1

  Description * EZVPN inside *.

  IP 172.16.217.1 255.255.255.0

  IP helper 10.1.4.60

  IP helper 10.1.4.61

  IP tcp adjust-mss 1452

  Crypto ipsec client ezvpn EZVPN inside

  !

  IP forward-Protocol ND

  IP http server

  23 class IP http access

  local IP http authentication

  IP http secure server

  IP http timeout policy slowed down 60 life 86400 request 10000

  !

  IP route 0.0.0.0 0.0.0.0 dhcp

  Hello

  As long as the traffic to any other network other than the network to remote sites runs through the VPN connection, then the more typical than the ASA things central may be missing are the following

  permit same-security-traffic intra-interface

  If this configuration is already currently in use can be controlled with

  See the race same-security-traffic

  The above arrangement allows the ASA transmitting a packet entering an interface through this same interface, that it came at the start. Without this parameter, it is not impossible.

  Then you will naturally NAT configurations for users of the Remote LAN connections

  If we were to use NAT Auto / network object NAT (since I don't know how you have built the base dynamic PAT to your central site ASA) configuration might look something like this

  network of the REMOTE-SITE-PAT object

  172.16.217.0 subnet 255.255.255.0

  dynamic NAT interface (outdoors, outdoor)

  The above should provide the dynamic PAT to the interface ' outside ' of the ASA central when the hosts are connected to the Internet.

  Given that the NEM Mode VPN is probably connected right now that you can test what would happen to a related Internet packet across the VPN connection (even before changing the settings above)

  entry Packet-trace out tcp 172.16.217.100 12345 8.8.8.8 80

  That should tell what happens to the content of the package. If you are missing the first order, I suggest you the output of "packet - trace" will be very short and should see a DECLINE Phase very quickly

  -Jouni

• It would work for a WLAN internet access?

  Hi, everyone, I have a few questions about how to implement public access to Internet in our workplace that would not allow access to our local network.  We have several access points 2702 and 2504 WLAN controller.  Two of the four interfaces on the 2504 have intellectual property in the ranks of our LAN subnets.  I assigned a VLAN for public access to the Internet, but do not know how I would implement on our infrastructure past.  Instead, I was thinking about a cable connected to one of the unused interfaces on the 2504 to a port on our DMZ switch and having traffic for the public Internet, out across the demilitarized zone.  If I had to do this way, but also created a scope DHCP for the public Internet, and the DHCP scope were on an interface that had an address on the local corporate network, customers would always get the address?  What is the best way to do it?

  A second question I have is about how the traffic between the access points and the controller is managed.  When a client connects to the access point, their traffic get dug to the controller and then thrown on the LAN, or the traffic goes to the local network directly from the access point?  The reason why I ask is that we have a remote office that we would like to manage the access point of the controller in the Office at home, but we do not want necessarily all their traffic going back or the office, if it was intended for office network at home, or if it is intended for the Internet.  The remote desktop has its own local internet connection and is just VPN'ing to the desktop at home for internal network traffic.  DHCP for clients at the remote office is managed by a DHCP server on the router on this effect.  A remote desktop access point connected to the controller in the head office would be able to use the DHCP server on the router to the remote desktop?  I test that out in a lab environment and I couldn't get it to work this way.  Remote desktop access point is currently running in mode independent and done a good job.  In the future, this site will also get on our MPLS and finally all traffic going to get dug towards the Home Office, including Internet access, so perhaps at that time, attach the remote AP to the controller would be better.

  Thank you!

   A second question I have is regarding to how traffic is handled between the access points and the controller. When a client connects to the access point, does their traffic get tunnelled to the controller and then dumped onto the LAN, or does the traffic go to the LAN directly from the access point? 

  In local mode APs switch always centralized traffic, that is to say CAPWAP tunnel established between AP & WLC. If all traffic comments terminate at WLC connected switch.

  In your case, if you map the traffic comments-SSID to the physical port connects to the DMZ switch, guest SSID users end traffic to DMZ switch. You must ensure that traffic vlan is not go on any other connected WLC trunk ports.

  If AP mode FlexConnect, then traffic will end at the switch where AP connected locally.

  HTH

  Rasika

  Pls note all useful responses *.

• Extend my extreme network with another extreme - waiting for internet access

  Hello - I have a new generation Airport Extreme (let's call it Extreme1) connected to a Comcast modem and it works very well. The extreme will be the router that the modem has no router function. I'm trying to expand my network to another room with another extreme (let's call it Extreme2). I have a connection cable between two rooms. Extreme1 has an ethernet cable from one of its LAN ports connected on port WAN Extreme2. When I try to create a new network with Extreme2 (in aid of the same name, passwords, etc.) it does not work. He was suspended at the end when he is looking for a connection ("Waiting for internet access")-I did the following things based on what I read here:

  1. Changed IPv6 link local parameters
  2. Tried the whole upward on my Macbook and tried on my iphone
  3. The Wan first and then tried to change the configuration after you done for Extreme2 by creating a network
  4. Tried to create a network with Extreme2 connected directly to the modem
  5. Extreme2 factory reset after every attepmt

  And nothing works. Kicker is, I also have a reasonably new airport express and the same thing happens to her as well.

  Do I need to adjust some parameters of network that I'm not aware of? Is it possible that my LAN ports are disabled on Extreme2? It is brand new.

  Thanks for any help.

  Have you used the Apple Setup Assistant?  If you did, it had notified you that the extreme second was being configured "add using Ethernet. The wizard will automatically configure the second airport with the appropriate settings for you.  All you have to do is enter a name of device for the second AirPort Extreme.

  Here I'm assuming that you reset the second extreme to parameters by default until you set it up again and that your second Extreme is the current version of the "tower" or that of previous versions "flat or square.

  The example below shows an AirPort Express as the device which is the extension of the network, but you will see the name of your network and AirPort Extreme on your configuration screen.

  Post back if you need some tips on using the "Wizard" for your configuration.

  

• block internet access to members who

  The scenario is

  Server 2008 R2 edition OS.
  Roll of server's DNS, AD, and DC with NAT distributed to the local network configured for internet access.
  A DHCP server or a proxy server so itself is a default gateway and DNS for LAN users.  Very small local area network and all machines have IP, default gateway, and DNS configured manually.
  Advantage is the server machine can access the internet.
  AD users can access the internet.
  Downside is computer user who connects to a local computer, the credentials of the local user, also has internet access.
  Need solution for this query not implemented DHCP or a proxy server adding extra costs for the company.

  Hello

  I suggest you according to the question in this forum and check if that helps:

  http://social.technet.Microsoft.com/forums/en-AU/winservermanager/

  It will be useful.

• I'm not able to get wireless internet access after entering my security at the back of my modem key.

  I recently bought a thread to get a wireless connection after you plug the usb driver proceeded to create a connectin wireless, then asked to type in the security encrypted code that did got a connection but said auto and not Internet, but bars are high and shows a connection, I hope that I have been specific with the problem iam having.another thing on my laptop I have access to the internet and typed in the security key on the back of my modem... Tenda is the name of the usb driver.

  original title: no internet access

  Hello

  Are you binder to share internet from your laptop or your internet provider cable is connected to this wireless USB dongle / device?

  If you share internet by connecting this USB to a computer, you will need to share internet on this computer.

  You must enable "Internet connection sharing", click on Start menu-> network connections-> right click on the connection to the LAN-> select properties-> click on the tab 'Advanced'-> Tickmark 'allow other users to connect through this connection to computers.

  I hope this helps.

• My Windows XP computer doesn't have internet access. I tried ipconfig and it shows default gateway.

  I have Windows XP Home... and all of a sudden I get no internet access.  When I do ipconfig... it does not show a default gateway.  I did everything update driver LAN, resetting the router, restart, by specifying the IP address (from the automatic ip configuration) and is still not available.  I know that the router is that I can access it from another computer.  any help would be greatly appreciated.

  original title: default gateway problem

  Is the connection wired or wireless?

  What version of XP, including service pack? (do right click my computer and select properties for info)

  It happened just before this problem occurred (failure, virus infection, etc.)?

  If this is a wired connection (which, I suppose, since you mention the 'LAN' pilot), have you tried to connect the Ethernet cable into a different socket on the router, (b) using an Ethernet cable from verified (maybe the computer that works), or (c) confirming that the Green LED next to the computer's Ethernet Jack lights up when the cable is connected?

  Given that you know about ipconfig, it would have helped if you had provided the results of the ipconfig command.  Here's a way to do it, but first configure the card to obtain an IP address automatically

  • Open a command prompt window
  • Type the following lines and press ENTER after each line

  ipconfig/all > "% userprofile%\Desktop\ipinfo.txt".
  Notepad '% userprofile%\Desktop\ipinfo.txt '.

  • Copy and paste the contents of the Notepad document in your response.  Close the command prompt window and the window of Notepad and remove ipinfo.txt from your desktop.