remote VPN cannot access mail server of asa
Hi dear.
I have the router that connect to the asa.
Internet line to connect to the router so all the nat translation is made to the router.
router outside the ip:x.x.xx
router inside the ip:10.0.0.1 interface that is connect to asa outside interface (asa outside ip address: 10.0.0.2)
my mail server to connect to the DMZ asa.
DMZ interface ip address:172.16.10.0./24
mail server IP:172.16.10.10
I'm twice nat for the ip address of the mail server.
1.i do to asa.
static (DMZ, Outside) 10.0.0.10 172.16.10.10
in this mail server ip 172.16.10.10 translation translating 10.0.0.10(10.0.0.10 ip est un sous-réseau de la plage de connexion routeur et asa).
second nat to router.
IP nat inside source static tcp 10.0.0.10 25 25 ext x.x.x.x public ip x.x.x.x
I have no problem with my nat translation to my e-mail server.
I have set up remote client vpn to asa and apply crypto map ASA outside interface which is 10.0.0.2
I do THE static nat router for asa outside ip address.
IP nat inside source static udp 10.0.0.2 x.x.x.x extensible 500 500
IP nat inside source static udp 10.0.0.2 4500 4500 extensible x.x.x.x
I have no problem with the vpn connection. I can connect vpn connection. but I can't access mail server. 172.16.10.10
What can I do in this situation?
I should be writing sheep-access list?
If Yes, how can I write this access list?
Yes, you must configure access on your ASA sheep-list as follows:
IP 172.16.10.0 allow Access-list sheep-dmz 255.255.255.0
NAT 0 access-list sheep-dmz (dmz)
Tags: Cisco Security
Similar Questions
-
Remote VPN cannot access devices LAN or internet
So I have a server and a computer inside that I can access through an ASA 5505 with ASA 9.2 (1) and ASDM 7.2 (1)
The computer on 192.168.1.110 via port 8080 can show me a demo site.
The server on 192.168.1.222 got my DNS, HTTP, FTP, mail and more about it.
Outside, I got a computer (by outside, I hear from the firewall and the cable directly into the computer) on 192.168.20.2 and firewall outside being 192.168.20.1
From the outside I can access the 8080 without problem (and I guess as well with the server, but it is on another default gateway and are not accessible right now). -When I connect through my VPN I am assigned 192.168.30.5 but unable to connect inside the computer through 192.168.1.110:8080.
This will return the error: asymmetrical NAT rules matched for before and back flow; Connection for udp src outdoors: 192.168.30.5/49608 (...) dst inside: 192.168.1.222/53 refused because of the failure of the path reverse NAT.
Somewhere, I had a conflict or a non-created access rule. Anyone who wants to take a shot?
I marked with "BOLD" for what I thought that may be the cause.
ciscoasa (config) # sh running-config
: Saved
:
ASA Version 9.2 (1)
!
ciscoasa hostname
activate 8Ry2YjIyt7RRXU24 encrypted password
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
2KFQnbNIdI.2KYOU encrypted passwd
names of
192.168.30.5 mask - 192.168.30.200 local pool Pool of IP IP 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.254 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
address 192.168.20.1 255.255.255.0
!
boot system Disk0: / asa921 - k8.bin
passive FTP mode
permit same-security-traffic intra-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
object network testServer-8080
host 192.168.1.110
Description of the test server
network of the object server-21
Home 192.168.1.222
Description of the test server
network of the object Server-25
Home 192.168.1.222
Description of the test server
network of the object Server-53
Home 192.168.1.222
Description of the test server
network of the object server-80
Home 192.168.1.222
Description of the test server
network of the object server-443
Home 192.168.1.222
Description of the test server
network of the object server-2525
Home 192.168.1.222
Description of the test server
network of the object server-993
Home 192.168.1.222
Description of the test server
network of the object server-6001
Home 192.168.1.222
Description of the test server
network of the object server-6002
Home 192.168.1.222
Description of the test server
network of the object server-6003
Home 192.168.1.222
Description of the test server
network of the object server-6004
Home 192.168.1.222
Description of the test server
network of the VPN HOST object
192.168.30.0 subnet 255.255.255.0
network of the object inside
host 192.168.1.0
the vpn server object network
Home 192.168.1.222
outside_access_in list extended access permit tcp any object testServer-8080 eq 8080
outside_access_in list extended access permit tcp any object server-21 eq ftp
outside_access_in list extended access permit tcp any object Server-25 eq smtp
outside_access_in list extended access permit tcp any object server-2525 2525 eq
outside_access_in list extended access permit udp any object server-53 eq inactive field
outside_access_in list extended access permit tcp any object server-80 eq www
outside_access_in list extended access permit tcp any object server-443 https eq
outside_access_in list extended access permit tcp any object server-993 993 eq
outside_access_in list extended access permit tcp any object server-6001 eq 6001
outside_access_in list extended access permit tcp any object server-6002 6002 eq
outside_access_in list extended access permit tcp any object server-6003 eq 6003
outside_access_in list extended access permit tcp any object server-6004 eq 6004
outside_access_in to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.30.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 721.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) VPN-dynamic HOSTS within static destination to source Server VPN - vpn server
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
object network testServer-8080
NAT (inside, outside) interface static 8080 8080 tcp service
network of the object server-21
NAT static (inside, inside) of the service ftp ftp tcp interface
network of the object Server-25
NAT (inside, outside) interface static tcp smtp smtp service
network of the object Server-53
NAT static (inside, inside) interface tcp service area
network of the object server-80
NAT (inside, outside) interface static tcp www www service
network of the object server-443
NAT (inside, outside) interface static tcp https https service
network of the object server-2525
NAT (inside, outside) interface static 2525 2525 tcp service
network of the object server-993
NAT (inside, outside) interface static tcp 993 993 service
network of the object server-6001
NAT (inside, outside) interface static tcp 6001 6001 service
network of the object server-6002
NAT (inside, outside) interface static tcp 6002 6002 service
network of the object server-6003
NAT (inside, outside) interface static 6003 6003 tcp service
network of the object server-6004
NAT (inside, outside) interface static service tcp 6004 6004
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS AAA server HSS-auth-server protocol
allow only
AAA-server HSS-auth-server (inside) host 192.168.1.222
Timeout 5
key *.
identity of the user by default-domain LOCAL
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec pmtu aging infinite - the security association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
trustpool crypto ca policy
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal HSSvpn group strategy
attributes of Group Policy HSSvpn
value of server DNS 192.168.1.222
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value outside_access_in ! This value was its own name earlier
HSS.dk value by default-field
type tunnel-group HSSvpn remote access
attributes global-tunnel-group HSSvpn
address IP-pool pool
HSS-auth-server authentication-server-group
Group Policy - by default-HSSvpn
password-management
IPSec-attributes tunnel-group HSSvpn
IKEv1 pre-shared-key *.
tunnel-group HSSvpn ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:9859258e11364180cf9b3e21173b3f2f
: endHello
"Nat" bold configuration is incorrect, as you would expect.
Replace it with something like this
the object of the LAN network
subnet 192.168.1.0 255.255.255.0NAT (inside, outside) 1 static source LAN LAN to static destination HOST-VPN-VPN-HOST
I also suggest using a separate access the ACL of the Tunnel from Split 'standard' list.
For example
standard SPLIT-TUNNEL access list permit 192.168.1.0 255.255.255.0
Naturally, you must pass the ACL above to used "group policy" .
In addition, if you want to control the incoming connections to VPN users in 'outside_access_in' ACL, then you could change the default settings on the SAA by running the command
No vpn sysopt connection permit
If you need to return back then just to deliver without 'no' in front. Then back to its default value. This does not show in the running configuration by the way.
With this setting all connections from VPN connections should be allowed on the interface ACL interface that ends the VPN connection. If in your case that would be the ACL attached to the 'outside' interface.
Hope this helps :)
-Jouni
-
We are struggling to print on my local printer when you use remote desktop to access the server (Server 2008). Cannot make it work. Any suggestions?
Hi EverettBurton,
The issue of Windows XP, you have posted is related to Windows XP in a domain environment. It is better suited for the IT Pro TechNet public. Please ask your question in the TechNet forums for assistance.
Hope the helps of information.
-
Cannot access the server message coming up and cannot convert files
Cannot access the server message coming up and can't convert the files. Works on my desktop, but not at home.
ER
Is it ExportPDF?
-
Customer remote cannot access the server LAN via VPN
Hi friends,
I'm a new palyer in ASA.
My business is small. We need to the LAN via VPN remote client access server.
I have an ASA5510 with version 7.0. I have configured remote access VPN and it can establish the tunnel with success. But I can not access the server.
Client VPN is 5.0.07.0290 version. Encrypted packages have increased but the decrypted packet is 0 in the VPN client statistics, after I connected successfully.
Next to the ASA, I show crypto ipsec sa, just deciphering the packets increase.
Who can help me?
Thank you very much.
The following configuration:
ASA Version 7.0(7)
!
hostname VPNhost
names
dns-guard
!
interface Ethernet0/0
nameif outside
security-level 10
ip address 221.122.96.51 255.255.255.240
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.42.199 255.255.255.0
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
shutdown
no nameif
no security-level
no ip address
management-only
!
ftp mode passive
dns domain-lookup inside
access-list PAT_acl extended permit ip 192.168.42.0 255.255.255.0 any
access-list allow_PING extended permit icmp any any inactive
access-list Internet extended permit ip host 221.122.96.51 any inactive
access-list VPN extended permit ip 192.168.42.0 255.255.255.0 192.168.43.0 255.255.255.0
access-list VPN extended permit ip 192.168.43.0 255.255.255.0 192.168.42.0 255.255.255.0
access-list CAPTURE extended permit ip host 192.168.43.10 host 192.168.42.251
access-list CAPTURE extended permit ip host 192.168.42.251 host 192.168.43.10
pager lines 24
mtu outside 1500
mtu inside 1500
ip local pool testpool 192.168.43.10-192.168.43.20arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list VPN
nat (inside) 1 access-list PAT_acl
route outside 0.0.0.0 0.0.0.0 221.122.96.49 10
username testuser password 123
aaa authentication ssh console LOCAL
aaa local authentication attempts max-fail 3no sysopt connection permit-ipsec
crypto ipsec transform-set FirstSet esp-des esp-md5-hmac
crypto dynamic-map dyn1 1 set transform-set FirstSet
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
isakmp enable outside
isakmp policy 1 authentication pre-share
isakmp policy 1 encryption des
isakmp policy 1 hash md5
isakmp policy 1 group 2
isakmp policy 1 lifetime 86400
isakmp nat-traversal 3600
tunnel-group testgroup type ipsec-ra
tunnel-group testgroup general-attributes
address-pool testpool
tunnel-group testgroup ipsec-attributes
pre-shared-key *
telnet timeout 5ssh timeout 10
console timeout 0: end
Topology as follows:
Hello
Configure the split for the VPN tunneling.
Create the access list that defines the network behind the ASA.
ciscoasa(config)#access-list Split_Tunnel_List remark The corporate network behind the ASA. ciscoasa(config)#access-list Split_Tunnel_List standard permit 10.0.1.0 255.255.255.0
Mode of configuration of group policy for the policy you want to change.
ciscoasa(config)#group-policy hillvalleyvpn attributes ciscoasa(config-group-policy)#
Specify the policy to split tunnel. In this case, the policy is tunnelspecified.
ciscoasa(config-group-policy)#split-tunnel-policy tunnelspecified
Specify the access tunnel split list. In this case, the list is Split_Tunnel_List.
ciscoasa(config-group-policy)#split-tunnel-network-list value Split_Tunnel_List
Type this command:
ciscoasa(config)#tunnel-group hillvalleyvpn general-attributes
Associate the group with the tunnel group policy
ciscoasa(config-tunnel-ipsec)# default-group-policy hillvalleyvpn
Leave the two configuration modes.
ciscoasa(config-group-policy)#exit ciscoasa(config)#exit ciscoasa#
Save configuration to non-volatile RAM (NVRAM) and press enter when you are prompted to specify the name of the source file.
Kind regards
Abhishek Purohit
CCIE-S-35269 -
ASA Site, Remote Site cannot access DMZ to the Hub site
So I've been scratching my head and I just can't visualize what I what and how I want to do.
Here is the overview of my network:
Headquarters: ASA 5505
Site1: ASA 5505
Site2: ASA 5505
Training3: ASA 5505
All Sites are connected L2L to the location of the Headquarters with VPN Site to Site.
Since the HQ site I can ping each location by satellite, and each satellite location I can ping the HQ site. I will also mention that all other traffic is also correctly.
Here's my number: HQ site, I have a DMZ set up with a web/mail server. This mail/web server is accessible from my HQ LAN, but not from the satellite location. I need allow that.
What should I do?
My second question is that I want for satellite sites to see networks of eachother. I should create a VPN network between sites, or can this be solved in the same way that the question of the DMZ?
I enclose the show run from my ASA HQ
See the race HQ ASA
For the mail/web server that requires access on the remote site VPN tunnels, you must add the servers to the acl crypto, similar to the way you have it for network access. Make sure that both parties have the ACL in mirror. If you're natting from the DMZ to the outside, make sure you create an exemption from nat from the dmz to the outside for VPN traffic.
For the second question, because you have only three sites, I would recommend creating a tunnel from site to site between two satellite sites.
HTH
PS. If you found this post useful, please note it.
-
ASA 5505 VPN cannot access inside the host
I have access remote VPN configuration on an ASA 5505, but cannot access the host or the AAS when I connect through the VPN. I can connect with the Cisco VPN client and the VPN is on on the SAA and it shows that I am connected. I have the correct Ip address, but I can't ping or you connect to one of the internal addresses. I can't find what I'm missing. I have the VPN without going through the ACL interface. Because I can connect but not going anywhere I'm sure I missed something.
framework for configuration below
interface Vlan1
nameif inside
security-level 100
10.1.1.1 IP address 255.255.255.0
IP local pool xxxx 10.1.1.50 - 10.1.1.55 mask 255.255.255.0
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto-map dynamic outside_dyn_map 20 set pfs
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
PFS set 40 crypto dynamic-map outside_dyn_map
Crypto-map dynamic outside_dyn_map 40 value transform-set ESP-3DES-SHA
Crypto-map dynamic inside_dyn_map 20 set pfs
Crypto-map dynamic inside_dyn_map 20 the value transform-set ESP-3DES-SHA
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
map inside_map 65535-isakmp ipsec crypto dynamic inside_dyn_map
inside crypto map inside_map interface
crypto ISAKMP allow inside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
global service-policy global_policy
XXXXXXX strategy of Group internal
attributes of the strategy group xxxxxxx
banner value xxxxx Site Recovery
WINS server no
24.xxx.xxx.xx value of DNS server
VPN-access-hour no
VPN - connections 3
VPN-idle-timeout 30
VPN-session-timeout no
VPN-filter no
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelall
by default no
disable secure authentication unit
disable authentication of the user
user-authentication-idle-timeout no
disable the IP-phone-bypass
disable the leap-bypass
disable the NEM
disable the NAC
NAC-sq-period 300
NAC-reval-period 36000
NAC-by default-acl no
the address value xxxxxx pools
enable Smartcard-Removal-disconnect
the firewall client no
WebVPN
url-entry functions
Free VPN of CNA no
No vpn-addr-assign aaa
No dhcp vpn-addr-assign
tunnel-group xxxx type ipsec-ra
tunnel-group xxxx general attributes
xxxx address pool
Group Policy - by default-xxxx
blountdr group of tunnel ipsec-attributes
pre-shared-key *.
Missing nat exemption for vpn clients. Add the following and you should be good to go.
inside_nat0_outbound list of allowed ip extended access any 192.168.10.0 255.255.255.0
NAT (inside) 0-list of access inside_nat0_outbound
-
RVL200 SSL VPN: cannot access a remote LAN with iPad2
RVL200 firmware 1.1.12.1
iPad2 cannot access any device on the Remote LAN despite the closed padlock icon.
Is there another App needed? Or how to debug SSL VPN?
Emmanuel,
Were you able to access the LAN devices? Also, have you connected using a Mac or a PC successfully to verify that the devices are available? Sometimes antivirus and firewall software can block access to devices from a remote IP address.
-
Remote VPN cannot ping any host on remote site
Hi all!
I tried to deploy remote vpn on my asa 5515-x. And my VPN client properly connected, but I can't ping any host on a remote network.
Here is my configuration:
ASA 1.0000 Version 2
!
names of
!
interface GigabitEthernet0/0
nameif inside
security-level 100
IP 192.168.10.252 255.255.255.0
!
interface GigabitEthernet0/1
nameif outside
security-level 0
IP x.x.x.x 255.255.255.252
!
interface GigabitEthernet0/2
DMZ description
nameif dmz
security-level 50
IP 192.168.20.252 255.255.255.0
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
No nameif
no level of security
no ip address
!
interface Management0/0
nameif management
security-level 100
IP 192.168.2.40 255.255.255.0
management only
!
boot system Disk0: / asa861-2-smp - k8.bin
passive FTP mode
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
internal subnet object-
192.168.10.0 subnet 255.255.255.0
network dmz subnet object
subnet 192.168.20.0 255.255.255.0
Note to access-list LAN_VLAN_10 split_tunnel
split_tunnel list standard access allowed 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
management of MTU 1500
MTU 1500 dmz
IP local pool testpool 192.168.10.240 - 192.168.10.250 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ASDM image disk0: / asdm - 714.bin
don't allow no asdm history
ARP timeout 14400
!
internal subnet object-
NAT dynamic interface (indoor, outdoor)
network dmz subnet object
NAT (dmz, outside) dynamic interface
Route outside 0.0.0.0 0.0.0.0 93.174.55.181 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication LOCAL telnet console
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.0.0 255.255.0.0 management
http 192.168.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set esp - esp-md5-hmac ikev1 firstset
Crypto-map dynamic dyn1 ikev1 transform-set firstset 1 set
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
mymap outside crypto map interface
Crypto ikev1 allow outside
IKEv1 crypto policy 1
preshared authentication
the Encryption
md5 hash
Group 2
life 43200
Telnet 0.0.0.0 0.0.0.0 inside
Telnet 0.0.0.0 0.0.0.0 management
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 management
SSH timeout 5
Console timeout 0
interface ID client DHCP-client to the outside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group testgroup strategy
testgroup group policy attributes
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list split_tunnel
user1 fvosA8L1anfyxTw3 encrypted password username
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
address testpool pool
strategy-group-by default testgroup
testgroup group tunnel ipsec-attributes
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
What's wrong?
TNX!
Hello
I would like to change the current reserve of VPN to something overlapping to the LAN.
You're also missing NAT0 for the VPN Client connection that is your problem more likely.
You can try these changes
mask of 192.168.100.1 - local 192.168.100.254 pool POOL VPN IP 255.255.255.0
tunnel-group testgroup General attributes
No address testpool pool
address VPN-POOL pool
no ip local pool testpool 192.168.10.240 - 192.168.10.250 mask 255.255.255.0
the object of the LAN network
192.168.10.0 subnet 255.255.255.0
network of the VPN-POOL object
255.255.255.0 subnet 192.168.100.0
NAT static destination LAN LAN (indoor, outdoor) static source VPN-VPN-POOL
You can also change your settings for encryption for anything other than a. You can use AES.
Hope this helps
Let us know if this helped.
Don't forget to mark a reply as the answer if it answered your question.
Feel free to ask more if necessary
-Jouni
-
Certificate self-signed for remote VPN CLIENT access
Hi people,
I am trying to achieve two-factor authentication, first with RADIUS & 2nd with self-signed certificate. If I generated of self-signed certificate & trying to import this certificate but error 39 that occur. Only obstacle that authenticate with certificate. I saw some documents for separate setting certifcate servers (CA) & then to import in the clients but I m curious about a certificate automatically generated can be used to authenticate the remote access client.
ASA additional server failover mode is Local CA is not supported. Is there a way to support local CA.
Thank you
Are you talking about using self-signed client certificates? I guess that it will not work. At least it is not scalable. You must use an internal CA for this task. As the local certification authority cannot be used with failover, you can take a Windows Server 2 k 3 or 2 k 8. Another option is to use a router IOS as CA-server. But what take something else as a second factor? I'm a big fan of the use of smartphones with the www.duosecurity.com service.
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
ASA5500 - anyconnect VPN not access Web server in DMZ
I am at a loss. I enclose my config. I can access DMZ from within the network, but cannot access DMZ of VPN.
Any help would be great.
Rich
Also have question access to management 0/0 (192.168.1.1) of the Interior of the E0/1 (192.168.2.0) network
For your VPN - DMZ problem, the following is the most likely cause of your problem:
nat (inside,dmz) source static obj-dmz obj-dmz destination static obj-vpnpool obj-vpnpool
You should have in place:nat (outside,dmz) source static obj-vpnpool obj-vpnpool static obj-dmz obj-dmz
That's because VPN clients appear to come from the outside (to some purposes NAT) and the need to be exempt from NAT to access the resources of the DMZ. Management problems, the problem is asymmetric routing. When your packages arrive on the management UI, the ASA will try to send back traffic (starting with the 3-way TCP transfer protocol which will fail) through the inside interface but that won't work because ASA helped him, the source of the acknowledgement of receipt would SAA within the interface IP address, not the address of interface management in which the SYN sent. That's why most of the people have not historically used the management interface to ASA unless you have a real out-of-band network for management. Cisco recently introduced a separate fair management routing table, but you need to switch to 9.5 (1) or later to take advantage of that. -
PIX501 customer VPN - cannot access inside the network with VPN Session
What follows is based on the config on the attached link:
PIX Ver 6.2 (3) - VPN Client 3.3.6(A) - Windows XP Client PC
We can establish the VPN to the PIX501 session, but we cannot access the network private behind the pix.
Here is the config - I can't determine why it does not work, we are desperate to get there as soon as POSSIBLE!
We have the same problem with the customer 4.0.3(c)
Thanks in advance for any help!
=======================================
AKCPIX00 # sh run
: Saved
:
6.2 (3) version PIX
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
hostname AKCPIX00
domain.com domain name
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol 2000 skinny
fixup protocol sip udp 5060
names of
access-list 101 permit ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0
pager lines 24
interface ethernet0 10baset
interface ethernet1 10full
Outside 1500 MTU
Within 1500 MTU
external IP address #. #. #. # 255.255.240.0
IP address inside 192.168.1.5 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool akcpool 10.0.0.1 - 10.0.0.10
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
(Inside) NAT 0-list of access 101
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 #. #. #. # 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
the ssh LOCAL console AAA authentication
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
No sysopt route dnat
Crypto ipsec transform-set esp - esp-md5-hmac RIGHT
Crypto-map dynamic dynmap 10 transform-set RIGHT
map mymap 10-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
ISAKMP allows outside
part of pre authentication ISAKMP policy 10
encryption of ISAKMP policy 10
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup address akcpool pool akcgroup
vpngroup dns 192.168.1.10 Server akcgroup
vpngroup akcgroup by default-domain domain.com
vpngroup split tunnel 101 akcgroup
vpngroup idle 1800 akcgroup-time
vpngroup password akcgroup *.
vpngroup idle 1800 akc-time
Telnet timeout 5
SSH #. #. #. # 255.255.255.255 outside
SSH timeout 15
dhcpd address 192.168.1.100 - 192.168.1.130 inside
dhcpd dns 192.168.1.10
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd allow inside
Terminal width 80
Cryptochecksum:XXXXX
: end
AKCPIX00 #.
Config looks good - just as domestic mine to my local network. The only thing I can think is that you may have entered commands in the wrong order - which means, you could have isakmp or encryption before the config map was complete. Write memory, then reloading the pix is a way to reset everything. If you do not want downtime:
mymap outside crypto map interface
ISAKMP allows outside
Enter these two commands should be enough to reset the ipsec and isakmp.
-
Remote user cannot access the internet
Hello
I have a problem with my remote vpn users. They can't access internet after they establish the vpn connection. I read on the split tunnel and I think that its set up right, but his does not.
Please if you have time take a look. I have attached my asa 5505 configuration
Best regards.
your split tunneling is configured correctly, but group policy in which will done this configuration is not applied to the tunnel-group:
tunnel-group monitoring_vpn_group General-attributes
Group Policy - by default-monitoring_vpn_policy
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
Creating remote VPN redundancy with 2 ISPS on ASA 8.3 running
Hello
I need help in implementing connection remote VPN with two ISPs (redundancy), so that the remote VPN client will be only one connection, but two ISPS will be linked to another.
I can do it on previous IOS, but things have changed in ASA 8.3, please help.
Hello
If you follow the post, you will find that the "tunnel-group" is a global command that is not set to a specific interface.
Basically, must be added the card encryption even for two interfaces, as follows:
backup_map interface card crypto outside
backup of crypto backup_map interface card
crypto ISAKMP allow outside
ISAKMP crypto enable backup
The only difference is related to the statements of NAT, reason why I included the pre - NAT post in my previous note.
Thank you.
-
Original title: W7 error play "Media is not available.
On W7 Ultimate, I'm having a problem in the use of "play to" media action to my Sony TV. The tv is visible as a device and it is the same for the laptop to the TV. On laptop I get the error: "themedia is not available." Similarly, when I try to access the laptop to TV, I get error "can not access the server. any solution?
What exact model Sony TV? You may need to install additional softwareSee the content if you want to browse the content on the computer from the computerthe TV. as to play to, seefor beginners.BarbMVP - Windows/entertainment and connected homePlease mark as answer if that answers your question
Maybe you are looking for
-
Click problem 2 Pro P30W Miracast satellite
My Satellite click 2 Pro P30W has not long the option to display wireless on Windows 8.1I'm going to devices-> project, but I don't have the option "add a wireless display.Is there any Toshiba Software to manage the wireless display?
-
Why V7 is still not compatible with toolbar Yahoo?
Whenever I update to version recommended FF, it takes a few minutes so for my modules become compatible - but with the V7 one weeks and still no compatibility with Yahoo-toolbar, that I use on my laptop using V6!
-
Can I program my Philips tv remote
I have a philips hdtv 44. Can I program my sonyre-adpo72 remote to control my TV?
-
I'm forget password I want new urgently try last5 day iam password new password
I'm forget password I want new urgently try last5 day iam password new password
-
you have a call saying theres a problem with my computer
microsoft Windows contact people by phone to tell them of problems