Remote VPN cannot access devices LAN or internet

Similar Questions

• RV320 VPN cannot access peripheral LAN using iPad

  With the help of RV320, firmware 1.1.1.06

  LAN 192.168.1.x 255.255.255.0

  VPN 192.168.09.100 to 192.168.09.150

  I need to access a device on the local network using this VPN connection from iPad. The Unit received address DHCP on LAN, broadcasts its presence every second on the Port 4992.

  When it is on the LAN, the iPAD sees the presence of broadcasting and accesses the device without problem. When I VPN in, easy VPN works well. I configured the firewall of the router as the rules:

  Allow

  All traffic [1]

  LAN

  192.168.9.100 ~ 192.168.9.150

  192.168.1.1 ~ 192.168.1.255

  Always

  Allow

  All traffic [1]

  LAN

  192.168.1.1 ~ 192.168.1.255

  192.168.9.100 ~ 192.168.9.150

  Alway

  If I first connect to the device when the iPad is on the local network, I turn off WiFi and connect through the VPN, I can continue to control the device. However, if I'm not connected to the device locally first, I see the presence broadcast on port 4992 when it connects first via the VPN. Broadcasting does not reach the iPad from a 192.168.1.x device connected 192.168.9.x.

  What is the correct way for the iPad on the 192.168.9.x, see the dissemination of 192.168.1.x?

  Hello

  Broadcasts will not be sent on the VPN tunnel.  The only traffic that will pass from the LAN to your customer's traffic specifically aimed at it, otherwise the router send him outside.  Looks like your presence Pack is a show, so all VPN clients won't be able to see.

  I think that when you connect locally you are picking up on the broadcast and then when you go to the VPN that has not passed yet, so why does it work if you connect locally first.

  Hope that helps a little,

  Christopher Ebert - Advanced Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• remote VPN cannot access mail server of asa

  Hi dear.

  I have the router that connect to the asa.

  Internet line to connect to the router so all the nat translation is made to the router.

  router outside the ip:x.x.xx

  router inside the ip:10.0.0.1 interface that is connect to asa outside interface (asa outside ip address: 10.0.0.2)

  my mail server to connect to the DMZ asa.

  DMZ interface ip address:172.16.10.0./24

  mail server IP:172.16.10.10

  I'm twice nat for the ip address of the mail server.

  1.i do to asa.

  static (DMZ, Outside) 10.0.0.10 172.16.10.10

  in this mail server ip 172.16.10.10 translation translating 10.0.0.10(10.0.0.10 ip est un sous-réseau de la plage de connexion routeur et asa).

  second nat to router.

  IP nat inside source static tcp 10.0.0.10 25 25 ext x.x.x.x public ip x.x.x.x

  I have no problem with my nat translation to my e-mail server.

  I have set up remote client vpn to asa and apply crypto map ASA outside interface which is 10.0.0.2

  I do THE static nat router for asa outside ip address.

  IP nat inside source static udp 10.0.0.2 x.x.x.x extensible 500 500

  IP nat inside source static udp 10.0.0.2 4500 4500 extensible x.x.x.x

  I have no problem with the vpn connection. I can connect vpn connection. but I can't access mail server. 172.16.10.10

  What can I do in this situation?

  I should be writing sheep-access list?

  If Yes, how can I write this access list?

  Yes, you must configure access on your ASA sheep-list as follows:

  IP 172.16.10.0 allow Access-list sheep-dmz 255.255.255.0

  NAT 0 access-list sheep-dmz (dmz)

• CANNOT ACCESS THE LAN WITH THE EASY VPN CONFIGURATION

  Hello

  I configured easy vpn server in cisco 1905 SRI using ccp. The router is already configured with zone based firewall. With the help of vpn client I can reach only up to the internal interface of the router, but cannot access the LAN from my company. I need to change any configuration of ZBF since it is configured as "deny everything" from outside to inside? If so that all protocols should I match?   Also is there any exemption of NAT for VPN clients? Please help me! Thanks in advance.

  Please see my full configuration:

  Router #sh run
  Building configuration...

  Current configuration: 8150 bytes
  !
  ! Last modification of the configuration at 05:40:32 UTC Wednesday, July 4, 2012 by
  ! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
  ! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
  version 15.1
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  router host name
  !
  boot-start-marker
  boot-end-marker
  !
  !
  Passwords security min-length 6
  no set record in buffered memory
  enable secret 5 xxxxxxxxxxx
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  AAA authentication login ciscocp_vpn_xauth_ml_1 local
  AAA authorization exec default local
  AAA authorization ciscocp_vpn_group_ml_1 LAN
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  !
  !
  No ipv6 cef
  IP source-route
  no ip free-arps
  IP cef
  !
  Xxxxxxxxx name server IP
  IP server name yyyyyyyyy
  !
  Authenticated MultiLink bundle-name Panel
  !

  parameter-map local urlfpolicy TSQ-URL-FILTER type
  offshore alert
  block-page message "Blocked according to policy"
  parameter-card type urlf-glob FACEBOOK
  model facebook.com
  model *. Facebook.com

  parameter-card type urlf-glob YOUTUBE
  mires of youtube.com
  model *. YouTube.com

  parameter-card type urlf-glob CRICKET
  model espncricinfo.com
  model *. espncricinfo.com

  parameter-card type urlf-glob CRICKET1
  webcric.com model
  model *. webcric.com

  parameter-card type urlf-glob YAHOO
  model *. Yahoo.com
  model yapo

  parameter-card type urlf-glob PERMITTEDSITES
  model *.

  parameter-card type urlf-glob HOTMAIL
  model hotmail.com
  model *. Hotmail.com

  Crypto pki token removal timeout default 0
  !
  Crypto pki trustpoint TP-self-signed-2049533683
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 2049533683
  revocation checking no
  rsakeypair TP-self-signed-2049533683
  !
  Crypto pki trustpoint tti
  crl revocation checking
  !
  Crypto pki trustpoint test_trustpoint_config_created_for_sdm
  name of the object [email protected] / * /
  crl revocation checking
  !
  !
  TP-self-signed-4966226213 crypto pki certificate chain
  certificate self-signed 01
  3082022B 30820194 02111101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43647274 31312F30
  69666963 32303439 35323236 6174652D 3833301E 170 3132 30363232 30363332

  quit smoking
  encryption pki certificate chain tti
  for the crypto pki certificate chain test_trustpoint_config_created_for_sdm
  license udi pid CISCO1905/K9 sn xxxxxx
  licence start-up module c1900 technology-package datak9
  username privilege 15 password 0 xxxxx xxxxxxx
  !
  redundancy
  !
  !
  !
  !
  !
  type of class-card inspect entire tsq-inspection-traffic game
  dns protocol game
  ftp protocol game
  https protocol game
  match icmp Protocol
  match the imap Protocol
  pop3 Protocol game
  netshow Protocol game
  Protocol shell game
  match Protocol realmedia
  match rtsp Protocol
  smtp Protocol game
  sql-net Protocol game
  streamworks Protocol game
  tftp Protocol game
  vdolive Protocol game
  tcp protocol match
  udp Protocol game
  match Protocol l2tp
  class-card type match - all BLOCKEDSITES urlfilter
  Server-domain urlf-glob FACEBOOK game
  Server-domain urlf-glob YOUTUBE game
  CRICKET urlf-glob-domain of the server match
  game server-domain urlf-glob CRICKET1
  game server-domain urlf-glob HOTMAIL
  class-map type urlfilter match - all PERMITTEDSITES
  Server-domain urlf-glob PERMITTEDSITES match
  inspect the class-map match tsq-insp-traffic type
  corresponds to the class-map tsq-inspection-traffic
  type of class-card inspect correspondence tsq-http
  http protocol game
  type of class-card inspect all match tsq-icmp
  match icmp Protocol
  tcp protocol match
  udp Protocol game
  type of class-card inspect correspondence tsq-invalid-src
  game group-access 100
  type of class-card inspect correspondence tsq-icmp-access
  corresponds to the class-map tsq-icmp
  !
  !
  type of policy-card inspect urlfilter TSQBLOCKEDSITES
  class type urlfilter BLOCKEDSITES
  Journal
  reset
  class type urlfilter PERMITTEDSITES
  allow
  Journal
  type of policy-card inspect SELF - AUX-OUT-policy
  class type inspect tsq-icmp-access
  inspect
  class class by default
  Pass
  policy-card type check IN and OUT - POLICIES
  class type inspect tsq-invalid-src
  Drop newspaper
  class type inspect tsq-http
  inspect
  service-policy urlfilter TSQBLOCKEDSITES
  class type inspect tsq-insp-traffic
  inspect
  class class by default
  drop
  policy-card type check OUT IN-POLICY
  class class by default
  drop
  !
  area inside security
  security of the OUTSIDE area
  source of security OUT-OF-IN zone-pair outside the destination inside
  type of service-strategy check OUT IN-POLICY
  zone-pair IN-to-OUT DOMESTIC destination outside source security
  type of service-strategy inspect IN and OUT - POLICIES
  security of the FREE-to-OUT source destination free outdoors pair box
  type of service-strategy inspect SELF - AUX-OUT-policy
  !
  Crypto ctcp port 10000
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 2
  Group 2
  !
  ISAKMP crypto client configuration group vpntunnel
  XXXXXXX key
  pool SDM_POOL_1
  include-local-lan
  10 Max-users
  ISAKMP crypto ciscocp-ike-profile-1 profile
  vpntunnel group identity match
  client authentication list ciscocp_vpn_xauth_ml_1
  ISAKMP authorization list ciscocp_vpn_group_ml_1
  client configuration address respond
  virtual-model 1
  !
  !
  Crypto ipsec transform-set TSQ-TRANSFORMATION des-esp esp-md5-hmac
  !
  Profile of crypto ipsec CiscoCP_Profile1
  game of transformation-TRANSFORMATION TSQ
  set of isakmp - profile ciscocp-ike-profile-1
  !
  !
  !
  !
  !
  !
  the Embedded-Service-Engine0/0 interface
  no ip address
  response to IP mask
  IP directed broadcast to the
  Shutdown
  !
  interface GigabitEthernet0/0
  Description LAN INTERFACE-FW-INSIDE
  IP 172.17.0.71 255.255.0.0
  IP nat inside
  IP virtual-reassembly in
  security of the inside members area
  automatic duplex
  automatic speed
  !
  interface GigabitEthernet0/1
  Description WAN-INTERNET-INTERNET-FW-OUTSIDE
  IP address xxxxxx yyyyyyy
  NAT outside IP
  IP virtual-reassembly in
  security of the OUTSIDE member area
  automatic duplex
  automatic speed
  !
  interface Serial0/0/0
  no ip address
  response to IP mask
  IP directed broadcast to the
  Shutdown
  no fair queue
  2000000 clock frequency
  !
  type of interface virtual-Template1 tunnel
  IP unnumbered GigabitEthernet0/0
  ipv4 ipsec tunnel mode
  Tunnel CiscoCP_Profile1 ipsec protection profile
  !
  local IP SDM_POOL_1 172.17.0.11 pool 172.17.0.20
  IP forward-Protocol ND
  !
  no ip address of the http server
  local IP http authentication
  IP http secure server
  !
  IP nat inside source list 1 interface GigabitEthernet0/1 overload
  IP route 0.0.0.0 0.0.0.0 yyyyyyyyy
  IP route 192.168.1.0 255.255.255.0 172.17.0.6
  IP route 192.168.4.0 255.255.255.0 172.17.0.6
  !
  access-list 1 permit 172.17.0.0 0.0.255.255
  access-list 100 permit ip 255.255.255.255 host everything
  access-list 100 permit ip 127.0.0.0 0.255.255.255 everything
  access-list 100 permit ip yyyyyy yyyyyy everything
  !
  !
  !
  !
  !
  !
  !
  !
  control plan
  !
  !
  !
  Line con 0
  line to 0
  line 2
  no activation-character
  No exec
  preferred no transport
  transport of entry all
  output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
  StopBits 1
  line vty 0 4
  transport input ssh rlogin
  !
  Scheduler allocate 20000 1000
  end

  A few things to change:

  (1) pool of IP must be a single subnet, it is not the same subnet as your subnet internal.

  (2) your NAT ACL 1 must be changed to ACL extended for you can configure NAT exemption, so if your pool is reconfigured to be 10.10.10.0/24:

  access-list 120 deny ip 172.17.0.0 0.0.255.255 10.10.10.0 0.0.0.255

  access-list 120 allow ip 172.17.0.0 0.0.255.255 everything

  overload of IP nat inside source list 120 interface GigabitEthernet0/1

  No inside source list 1 interface GigabitEthernet0/1 ip nat overload

  (3) OUT POLICY need to include VPN traffic:

  access-list 121 allow ip 10.10.10.0 0.0.0.255 172.17.0.0 0.0.255.255

  type of class-card inspect correspondence vpn-access

  game group-access 121

  policy-card type check OUT IN-POLICY

  vpn-access class

  inspect

• RVL200 SSL VPN: cannot access a remote LAN with iPad2

  RVL200 firmware 1.1.12.1

  iPad2 cannot access any device on the Remote LAN despite the closed padlock icon.

  Is there another App needed? Or how to debug SSL VPN?

  Emmanuel,

  Were you able to access the LAN devices? Also, have you connected using a Mac or a PC successfully to verify that the devices are available? Sometimes antivirus and firewall software can block access to devices from a remote IP address.

• Remote user cannot access the internet

  Hello

  I have a problem with my remote vpn users. They can't access internet after they establish the vpn connection. I read on the split tunnel and I think that its set up right, but his does not.

  Please if you have time take a look. I have attached my asa 5505 configuration

  Best regards.

  your split tunneling is configured correctly, but group policy in which will done this configuration is not applied to the tunnel-group:

  tunnel-group monitoring_vpn_group General-attributes

  Group Policy - by default-monitoring_vpn_policy

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• ASA 5505 VPN cannot access inside the host

  I have access remote VPN configuration on an ASA 5505, but cannot access the host or the AAS when I connect through the VPN. I can connect with the Cisco VPN client and the VPN is on on the SAA and it shows that I am connected. I have the correct Ip address, but I can't ping or you connect to one of the internal addresses. I can't find what I'm missing. I have the VPN without going through the ACL interface. Because I can connect but not going anywhere I'm sure I missed something.

  framework for configuration below

  interface Vlan1

  nameif inside

  security-level 100

  10.1.1.1 IP address 255.255.255.0

  IP local pool xxxx 10.1.1.50 - 10.1.1.55 mask 255.255.255.0

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic outside_dyn_map 20 set pfs

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  PFS set 40 crypto dynamic-map outside_dyn_map

  Crypto-map dynamic outside_dyn_map 40 value transform-set ESP-3DES-SHA

  Crypto-map dynamic inside_dyn_map 20 set pfs

  Crypto-map dynamic inside_dyn_map 20 the value transform-set ESP-3DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  map inside_map 65535-isakmp ipsec crypto dynamic inside_dyn_map

  inside crypto map inside_map interface

  crypto ISAKMP allow inside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  global service-policy global_policy

  XXXXXXX strategy of Group internal

  attributes of the strategy group xxxxxxx

  banner value xxxxx Site Recovery

  WINS server no

  24.xxx.xxx.xx value of DNS server

  VPN-access-hour no

  VPN - connections 3

  VPN-idle-timeout 30

  VPN-session-timeout no

  VPN-filter no

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelall

  by default no

  disable secure authentication unit

  disable authentication of the user

  user-authentication-idle-timeout no

  disable the IP-phone-bypass

  disable the leap-bypass

  disable the NEM

  disable the NAC

  NAC-sq-period 300

  NAC-reval-period 36000

  NAC-by default-acl no

  the address value xxxxxx pools

  enable Smartcard-Removal-disconnect

  the firewall client no

  WebVPN

  url-entry functions

  Free VPN of CNA no

  No vpn-addr-assign aaa

  No dhcp vpn-addr-assign

  tunnel-group xxxx type ipsec-ra

  tunnel-group xxxx general attributes

  xxxx address pool

  Group Policy - by default-xxxx

  blountdr group of tunnel ipsec-attributes

  pre-shared-key *.

  Missing nat exemption for vpn clients. Add the following and you should be good to go.

  inside_nat0_outbound list of allowed ip extended access any 192.168.10.0 255.255.255.0

  NAT (inside) 0-list of access inside_nat0_outbound

• Remote VPN cannot ping any host on remote site

  Hi all!

  I tried to deploy remote vpn on my asa 5515-x. And my VPN client properly connected, but I can't ping any host on a remote network.

  Here is my configuration:

  ASA 1.0000 Version 2

  !

  names of

  !

  interface GigabitEthernet0/0

  nameif inside

  security-level 100

  IP 192.168.10.252 255.255.255.0

  !

  interface GigabitEthernet0/1

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.252

  !

  interface GigabitEthernet0/2

  DMZ description

  nameif dmz

  security-level 50

  IP 192.168.20.252 255.255.255.0

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/5

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  nameif management

  security-level 100

  IP 192.168.2.40 255.255.255.0

  management only

  !

  boot system Disk0: / asa861-2-smp - k8.bin

  passive FTP mode

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  internal subnet object-

  192.168.10.0 subnet 255.255.255.0

  network dmz subnet object

  subnet 192.168.20.0 255.255.255.0

  Note to access-list LAN_VLAN_10 split_tunnel

  split_tunnel list standard access allowed 192.168.10.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  management of MTU 1500

  MTU 1500 dmz

  IP local pool testpool 192.168.10.240 - 192.168.10.250 mask 255.255.255.0

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any inside

  ASDM image disk0: / asdm - 714.bin

  don't allow no asdm history

  ARP timeout 14400

  !

  internal subnet object-

  NAT dynamic interface (indoor, outdoor)

  network dmz subnet object

  NAT (dmz, outside) dynamic interface

  Route outside 0.0.0.0 0.0.0.0 93.174.55.181 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  AAA authentication LOCAL telnet console

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.0.0 255.255.0.0 management

  http 192.168.10.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec transform-set esp - esp-md5-hmac ikev1 firstset

  Crypto-map dynamic dyn1 ikev1 transform-set firstset 1 set

  dynamic mymap 1 dyn1 ipsec-isakmp crypto map

  mymap outside crypto map interface

  Crypto ikev1 allow outside

  IKEv1 crypto policy 1

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 43200

  Telnet 0.0.0.0 0.0.0.0 inside

  Telnet 0.0.0.0 0.0.0.0 management

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 management

  SSH timeout 5

  Console timeout 0

  interface ID client DHCP-client to the outside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal group testgroup strategy

  testgroup group policy attributes

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list split_tunnel

  user1 fvosA8L1anfyxTw3 encrypted password username

  tunnel-group testgroup type remote access

  tunnel-group testgroup General attributes

  address testpool pool

  strategy-group-by default testgroup

  testgroup group tunnel ipsec-attributes

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  What's wrong?

  TNX!

  Hello

  I would like to change the current reserve of VPN to something overlapping to the LAN.

  You're also missing NAT0 for the VPN Client connection that is your problem more likely.

  You can try these changes

  mask of 192.168.100.1 - local 192.168.100.254 pool POOL VPN IP 255.255.255.0

  tunnel-group testgroup General attributes

  No address testpool pool

  address VPN-POOL pool

  no ip local pool testpool 192.168.10.240 - 192.168.10.250 mask 255.255.255.0

  the object of the LAN network

  192.168.10.0 subnet 255.255.255.0

  network of the VPN-POOL object

  255.255.255.0 subnet 192.168.100.0

  NAT static destination LAN LAN (indoor, outdoor) static source VPN-VPN-POOL

  You can also change your settings for encryption for anything other than a. You can use AES.

  Hope this helps

  Let us know if this helped.

  Don't forget to mark a reply as the answer if it answered your question.

  Feel free to ask more if necessary

  -Jouni

• PIX501 customer VPN - cannot access inside the network with VPN Session

  What follows is based on the config on the attached link:

  http://www.Cisco.com/en/us/Partner/Tech/tk583/TK372/technologies_configuration_example09186a008009442e.shtml

  PIX Ver 6.2 (3) - VPN Client 3.3.6(A) - Windows XP Client PC

  We can establish the VPN to the PIX501 session, but we cannot access the network private behind the pix.

  Here is the config - I can't determine why it does not work, we are desperate to get there as soon as POSSIBLE!

  We have the same problem with the customer 4.0.3(c)

  Thanks in advance for any help!

  =======================================

  AKCPIX00 # sh run

  : Saved

  :

  6.2 (3) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  hostname AKCPIX00

  domain.com domain name

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  fixup protocol sip udp 5060

  names of

  access-list 101 permit ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  external IP address #. #. #. # 255.255.240.0

  IP address inside 192.168.1.5 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool akcpool 10.0.0.1 - 10.0.0.10

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  (Inside) NAT 0-list of access 101

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 #. #. #. # 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  ISAKMP allows outside

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup address akcpool pool akcgroup

  vpngroup dns 192.168.1.10 Server akcgroup

  vpngroup akcgroup by default-domain domain.com

  vpngroup split tunnel 101 akcgroup

  vpngroup idle 1800 akcgroup-time

  vpngroup password akcgroup *.

  vpngroup idle 1800 akc-time

  Telnet timeout 5

  SSH #. #. #. # 255.255.255.255 outside

  SSH timeout 15

  dhcpd address 192.168.1.100 - 192.168.1.130 inside

  dhcpd dns 192.168.1.10

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:XXXXX

  : end

  AKCPIX00 #.

  Config looks good - just as domestic mine to my local network. The only thing I can think is that you may have entered commands in the wrong order - which means, you could have isakmp or encryption before the config map was complete. Write memory, then reloading the pix is a way to reset everything. If you do not want downtime:

  mymap outside crypto map interface

  ISAKMP allows outside

  Enter these two commands should be enough to reset the ipsec and isakmp.

• one of the VM cannot access network LAN

  Hello

  I configured 3 VM on an ESXi 4.1 (see attached jpg file). one of the virtual machine (GSPPBPCDBVM), it cannot access the network LAN, even cannot ping Bridge but can ping GSPPBPCVM after I walk today, previously, it was ok. The other 2 VM can access LAN network. What could be the problem?

  GSPPBPCVM (128.1.8.x)

  GSPPBPCDBVM (128.1.8.x)

  AEPAD (10.8.1.x)

  vmnic1 (to connect to the local network virtual 128.1.8.x)

  vmnic0 (to connect to the local network virtual 10.8.1.x)

  Thank you and best regards,

  Kelvin

  With the configuration you have posted, you have a 50/50 chance that none of your VM will have access to the network, since you have 2 NICs connected to two different VLANS and virtual machines are assigned to these network cards based on the virtual switch port (assuming you use the default settings).

  To properly set up the network, you have two options:

  1.) VLAN tagging on the physical switch ports (what you have)

  In this case, you will need to create a second vSwitch and attach the second NETWORK card to this switch. Then connect virtual machines to the vSwitch and port group that is connected to the switch port VLAN corresponding physics.

  2.) VLAN tagging on the virtual port group (this is what I recommend)

  Configure the ports on your physical switch as the trunk (or ports 'labelled' If you use Procurve switches), create another port VM on vSwitch0 group and set up VLAN tags on the gropus (VMKernel, VM Network1, VM Network2) port

  Take a look at http://www.vmware.com/files/pdf/virtual_networking_concepts.pdf for more information.

  André

• On ASA 5505 VPN cannot access remote (LAN)

  I have an ASA 5505 upward and running, all static NAT statements I need to forward ports to the internal services such as smtp, desktop remotely and it works very well, however I have set up an IPSEC vpn connection that authenticates to our DC and part works. However, after I connect and cannot ping anything on the local network or access services. I don't know what a NAT statement I have corrected. Here is the config. I really need to get this up and going tomorrow. Thanks for any help.

  Tyler

  Just remove the line of nat (outside) and ACL outside_nat0_outbound.

  And talk about these statements:

  IPSec-1 sysopt connection permit... (If it is disabled, you can check with sh run sysopt).

  2, crypto isakmp nat traversal 10 or 20

  3 no NAT ACL, mention your local subnets as the source and vpn client as the destination.

  4, create the other ACL (ST) with different name and source and destination like no nat ACL.

  5, then type nat (inside) 0 access-list sheep

  6, in the dwgavpn group policy, talk to splittunnel tunnelspecified and mention the tunnel split ACL (ST).

  Concerning

• Cannot access ' inside' LAN of AnyConnect VPN

  Hello. I am having trouble with my VPN connection where I can connect to it very well, and access the internet, but I can't access the internal network. Anyone have any ideas on what I can check to solve that?

  I think that the suggestion concerning the exemption of NAT is very good. If that is not the issue, then I have some other suggestions.

  -with the session created VPN review information the AnyConnect and look in the route Details tab and be sure that these LAN addresses appear as secure routes.

  -check that the devices in the local network that you can not reach a route to addresses in the pool of the VPN.

  HTH

  Rick

• Remote access ASA - cannot access devices inside or outside

  Hello

  I have an ASA550: I configured a VPN IPSEC and can connect to the ASA and I can access the CLI.

  I can access internal devices of the ASA and I can access the internet.

  However, I can't access internal devices or over the internet from the computer connected to IPSec.

  Any help is appreciated!

  Here is the config:

  ASA Version 8.2 (5)

  !

  host name asa

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.47.70.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  passive FTP mode

  access extensive list ip 10.47.60.0 inside_nat0_outbound allow 255.255.255.0 10.47.70.0 255.255.255.0

  outside_access_in list extended access permit icmp any one

  outside_access_in list extended access permit udp any any eq

  outside_1_cryptomap list of allowed ip extended access all 10.47.60.0 255.255.255.0

  IP local pool hze_dhcp 10.47.60.10 - 10.47.60.41 mask 255.255.255.0

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA

  Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Crypto isakmp nat-traversal 3600

  management-access inside

  dhcpd dns 10.47.70.3

  dhcpd option 3 ip 10.47.70.1

  !

  dhcpd address 10.47.70.50 - 10.47.70.81 inside

  dhcpd allow inside

  !

  WebVPN

  internal DefaultRAGroup group strategy

  attributes of Group Policy DefaultRAGroup

  value of server DNS 8.8.8.8

  Protocol-tunnel-VPN IPSec l2tp ipsec

  attributes global-tunnel-group DefaultRAGroup

  address hze_dhcp pool

  Group Policy - by default-DefaultRAGroup

  IPSec-attributes tunnel-group DefaultRAGroup

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  Hello

  I don't think you have dynamic PAT configured for traffic from the VPN Client user who is supposed to browse the Internet through the connection WAN ASAs.

  Try adding

  NAT (outside) 1 10.47.60.0 255.255.255.0

  Also, the "packet-tracer" you question is not simulate the connection from the VPN Client. The user of the VPN Client is not behind the 'inside' interface and the Clients VPN address space does not include the IP 10.47.70.20.

  When the Client VPN connection is active, you can use the command "packet - trace"

  entry Packet-trace out tcp 10.47.60.x 12345 8.8.8.8 80

  While of course, replace 'x' with the real IP that the user got to the ASA

  -Jouni

• VPN works, but cannot access the LAN...

  I have cisco vpn client connection to a 1721 at the office. the client connects and I can access the office LAN but but not the local network. I have the box checked in client vpn to allow access to the local network. Help, please!

  Thank you!

  Matt

  Here is the config:

  Current configuration: 3901 bytes

  !

  version 12.2

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  Cerberus hostname

  !

  start the system flash c1700-k9o3sy7 - mz.122 - 11.T10.bin

  AAA new-model

  !

  !

  RADIUS AAA server group SERVERS RADIUS

  auth-port 1645 192.168.69.1 Server acct-port 1646

  !

  AAA authentication login LOGIN group SERVERS RADIUS local

  local NETGROUPAUTH AAA authorization network

  AAA - the id of the joint session

  !

  username mattheff password xxx

  username mikeheff password xxx

  clock timezone CST - 6

  clock to summer time recurring CDT 2 Sun Mar 2:00 1 Sun Nov 02:00

  IP subnet zero

  !

  !

  IP domain name heffnet.net

  name of the IP-server 68.94.156.1

  name of the IP-server 68.94.157.1

  DHCP excluded-address IP 192.168.69.1 192.168.69.99

  DHCP excluded-address IP 192.168.69.111 192.168.69.254

  !

  dhcp HEFFNET_LAN_POOL_1 IP pool

  network 192.168.69.0 255.255.255.0

  router by default - 192.168.69.254

  Server DNS 68.x.x.1 68.94.157.1

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  VPDN enable

  !

  VPDN-group pppoe

  demand dial

  Protocol pppoe

  !

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group VPNGROUP crypto isakmp client

  8mathef8 key

  68.x.x.1 DNS 68.94.157.1

  heffnet.net field

  pool VPN_CLIENT_POOL

  ACL 102

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac VPNSET1

  !

  crypto dynamic-map 10 DYNMAP

  game of transformation-VPNSET1

  !

  !

  list of authentication of card crypto VPNCLIENTMAP customer LOGIN

  list of crypto isakmp NETGROUPAUTH VPNCLIENTMAP card authorization

  crypto card for the VPNCLIENTMAP client configuration address respond

  card crypto VPNCLIENTMAP 10-isakmp dynamic ipsec DYNMAP

  !

  !

  !

  !

  interface Loopback0

  IP address 1.1.x.x.255.255.252

  !

  ATM0 interface

  Heffnet WAN/SBC DSL Interface Description

  no ip address

  No atm ilmi-keepalive

  PVC 0/35

  PPPoE-client dial-pool-number 69

  !

  DSL-automatic operation mode

  no fair queue

  !

  interface FastEthernet0

  Heffnet LAN Interface Description

  IP 192.168.69.254 255.255.255.0

  IP nat inside

  IP tcp adjust-mss 1452

  route VPN_ROUTE_MAP card intellectual property policy

  automatic speed

  !

  interface Dialer69

  MTU 1492

  the negotiated IP address

  NAT outside IP

  encapsulation ppp

  Dialer pool 69

  PPP chap hostname cerberus

  PPP chap password xxx

  PPP pap sent-username [email protected] / * / password xxx

  card crypto VPNCLIENTMAP

  !

  local IP VPN_CLIENT_POOL 192.168.70.200 pool 192.168.70.253

  IP nat inside source list interface INTERNALLY Dialer69 overload

  !

  IP classless

  IP route 0.0.0.0 0.0.0.0 Dialer69

  no ip address of the http server

  !

  !

  INTERNAL extended IP access list

  deny ip 192.168.69.0 0.0.0.255 192.168.70.0 0.0.0.255

  IP 192.168.69.0 allow 0.0.0.255 any

  !

  record 192.168.69.1

  access-list 101 permit ip 192.168.69.0 0.0.0.255 192.168.70.0 0.0.0.255

  access-list 102 permit ip 192.168.69.0 0.0.0.255 any

  !

  VPN_ROUTE_MAP allowed 10 route map

  corresponds to the IP 101

  set ip next-hop 1.1.1.2

  !

  alias exec s show ip interface brief

  alias exec sr show running-config

  !

  Line con 0

  privilege level 15

  Synchronous recording

  line to 0

  privilege level 15

  Synchronous recording

  line vty 0 4

  privilege level 15

  Synchronous recording

  line vty 5 15

  privilege level 15

  Synchronous recording

  !

  Scheduler allocate 4000 1000

  end

  Hi Matt,

  The config looks good. Please make sure that you get a route to 192.168.69.0 255.255.255.0 network only after the connection to the VPN client. Please also correspond to the exit "route print" before and after the connection. One last thing, I hope that the local network is not 192.168.69.0.

  HTH,

  Please rate if this helps,

  Kind regards

  Kamal

• Cannot access within LAN of Cisco Anyconnect

  I'm new to the firewall and try to get my Anyconnect test configuration to connect to addresses within my Local network. The Anyconnect client connects easily, I can get to addresses Internet and tracer package told me it falls to phase 6, svc-webvpn. Can someone post my config? I don't know I'm missing something pretty obvious. Config is pasted below:

  !

  interface Ethernet0/0

  Description< uplink="" to="" isp="">

  switchport access vlan 20

  !

  interface Ethernet0/1

  Description< inside="">

  switchport access vlan 10

  Speed 100

  full duplex

  !

  interface Ethernet0/2

  Description< home="" switch="">

  switchport access vlan 10

  !

  interface Ethernet0/3

  switchport access vlan 10

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  Shutdown

  !

  interface Ethernet0/6

  Shutdown

  !

  interface Ethernet0/7

  Shutdown

  !

  interface Vlan10

  nameif inside

  security-level 100

  IP 192.168.1.99 address 255.255.255.0

  !

  interface Vlan20

  nameif OUTSIDE

  security-level 0

  DHCP client dns update

  IP address dhcp setroute

  !

  Vlan30 interface

  No nameif

  no level of security

  no ip address

  !

  Banner motd

  Banner motd +... +

  Banner motd |

  Banner motd | Any unauthorized use or access prohibited * |

  Banner motd |

  Banner motd | The Officer allowed the exclusive use.

  Banner motd | You must have explicit permission to access or |

  Banner motd | configure this device. All activities performed.

  Banner motd | on this unit can be saved and violations of.

  Banner motd | This strategy may result in disciplinary action, and |

  Banner motd | may be reported to the police authorities. |

  Banner motd |

  Banner motd | There is no right to privacy on this device. |

  Banner motd |

  Banner motd +... +

  Banner motd

  boot system Disk0: / asa824-k8

  passive FTP mode

  clock timezone cst - 6

  clock to summer time recurring cdt

  permit same-security-traffic intra-interface

  ICMP-type of object-group DEFAULT_ICMP

  Description< default="" icmp="" types="" permit="">

  response to echo ICMP-object

  ICMP-unreachable object

  ICMP-object has exceeded the time

  object-group network obj and AnyConnect

  host of the object-Network 192.168.7.20

  host of the object-Network 192.168.7.21

  host of the object-Network 192.168.7.22

  host of the object-Network 192.168.7.23

  host of the object-Network 192.168.7.24

  host of the object-Network 192.168.7.25

  access-list 101 extended allow icmp a whole

  !

  Note access-list ACL_OUTSIDE < anyconnect="" permit=""> >

  ACL_OUTSIDE list extended access permitted tcp everything any https eq

  ACL_OUTSIDE list extended access permit icmp any any DEFAULT_ICMP object-group

  !

  VPN_NAT list extended access permit ip host 192.168.7.20 all

  VPN_NAT list extended access permit ip host 192.168.7.21 all

  VPN_NAT list extended access permit ip host 192.168.7.22 all

  VPN_NAT list extended access permit ip host 192.168.7.23 all

  VPN_NAT list extended access permit ip host 192.168.7.24 all

  VPN_NAT list extended access permit ip host 192.168.7.25 all

  access-list extended sheep allowed ip group object obj-AnyConnect 192.168.1.0 255.255.255.0

  pager lines 24

  Enable logging

  timestamp of the record

  logging buffered information

  logging trap information

  exploitation forest asdm errors

  MTU 1500 inside

  Outside 1500 MTU

  mask 192.168.7.20 - 192.168.7.25 255.255.255.0 IP local pool AnyconnectPool

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 645.bin

  don't allow no asdm history

  ARP timeout 14400

  Global (1 interface OUTSIDE)

  NAT (INSIDE) 1 192.168.1.0 255.255.255.0

  NAT (OUTSIDE) 1 access-list VPN_NAT

  Access-group ACL_OUTSIDE in interface OUTSIDE

  !

  router RIP

  network 192.168.1.0

  passive-interface OUTSIDE

  version 2

  !

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA authentication http LOCAL console

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  http 192.168.2.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Sysopt connection tcpmss 1200

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4688000 association

  Crypto-map dynamic dynmap 20 the value transform-set ESP-3DES-SHA

  map outside_map 64553-isakmp ipsec crypto dynamic dynmap

  outside_map interface card crypto OUTSIDE

  !

  ISAKMP crypto identity hostname

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  VPN-addr-assign local reuse-delay 120

  SSH 192.168.1.0 255.255.255.0 inside

  SSH 192.168.2.0 255.255.255.0 inside

  SSH timeout 60

  Console timeout 0

  management-access INTERIOR

  DHCP-client broadcast-flag

  dhcpd x.x.x.x dns

  dhcpd rental 43200

  dhcpd ping_timeout 2000

  dhcpd auto_config OUTSIDE

  !

  dhcpd address 192.168.1.150 - 192.168.1.180 inside

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  NTP 216.229.0.179 Server

  SSL encryption, 3des-sha1-aes128-sha1 aes256-sha1 sha1 rc4

  localtrust point of trust SSL outdoors

  WebVPN

  allow outside

  AnyConnect essentials

  SVC disk0:/anyconnect-win-4.2.01035-k9.pkg 1 image

  SVC disk0:/anyconnect-linux-64-4.2.01035-k9.pkg 2 image

  Picture disk0:/anyconnect-macosx-i386-4.2.01035-k9.pkg 3 SVC

  enable SVC

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  internal Anyconnect group strategy

  attributes Anyconnect-group policy

  value x.x.x.x DNS server

  VPN-tunnel-Protocol svc

  the address value AnyconnectPool pools

  type tunnel-group remotevpn remote access

  tunnel-group Anyconnect type remote access

  tunnel-group Anyconnect General attributes

  strategy-group-by default Anyconnect

  tunnel-group Anyconnect webvpn-attributes

  enable MY_RA group-alias

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  Auto-update 30 3 1 survey period

  Update automatic timeout 1

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e

  : end

  Hello

  You are missing a NAT FREE for Anyconnect traffic would allow you to access inside the network.

  access-list allowed sheep ip 192.168.1.0 255.255.255.0 192.168.7.0 255.255.255.0

  NAT (inside) 0 access-list sheep

  Add these two lines in the config file and you should be able to access the network interior.

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.