Similar Questions

• vsphere5.5 + Rs 5.5 = recovery remove datastore error

  Good afternoon.

  Recently updated structure to update to vsphere 5.5 and 5.5 SRM.

  Planned migration works well. There was a problem with the emergency recovery.

  Simulate the situation:

  (1) we have two VM protected, turn off the power to the host, I go to the Dr site and perform disaster recovery.

  The following errors appear during the recovery process. This is normal, because the guests of inactivity.

  Here are the errors:

  Protected shutdown VMs on the Site - error - unable to communicate with the remote host, because it is disconnected. Cannot communicate with the remote host, because it is disconnected.

  Prepare the VMs of Site protected for Migration - Error - the operation is not allowed in the current state of the connection to the host. The operation is not allowed in the current state of the connection to the host. Impossible to cancel the registration of protected virtual machines.

  Change read-only storage - error - Impossible to cancel the protected registration. VMs cannot unsubscribe VMs protected.

  (2) go to the site recovery, everything seems fine. SRM offers redo recovery, because there were errors. Host power, perform a recovery and that's where the problems begin. Begin to pour into the error about unable to disassemble the data store, namely:

  Error - Impossible of datastore "DS1" from host 'host1. The "DS1" resource is in use.

  DS1 - the data store in the site protected, host1 - host in a protected site, where VM under tension before the recovery process

  Remarkably, manually remove the data store that it does not work too. That allows you to reboot the host again, but that's not important.

  Who can tell what is wrong or who have experienced when working with MRS? Ko is suitable for my case is not found.

  5.1 and it works very well.

  Thanks in advance for your help

  Correction of a problem.

  By default for each host - / var/log/vsantraces-> simlink to the data store.

  esxcli vsan defined trace Pei/var/log/vsan

• Failure of power CLI remove Datastore

  The Installation of ESXi generates a "datastore1".

  It is possible to generate an additional data store named 'Datastore1' via PowerCLI.

  The name is keysensitive, because it is not possible to generate an additional "datastore1".

  I have the following problem:

  With CLI power, it is not possible to remove the Datastore1 or datastore1.

  the command remove-data store with the parameter of the data store name cannot remove the data store,

  with error: there is more than one object with the name 'datastore1 '.

  In this command, the name is not supported keysensitive.

  It is not possible to use the ID of the store of data as a parameter for the deletion.

  Anyone have an idea how I could handle this problem with Power CLI?

  Thanks for the help!

  Chris

  What you can do to remove a specific data store, is to use the operator - ceq PowerShell which performs a case-sensitive comparison. Something like:

  Get-Datastore | Where-Object { $_.Name -ceq "Datastore1" } | Remove-Datastore
  

  If you want to remove both you can do:

  Get-Datastore | Where-Object { $_.Name -eq "Datastore1" } | Remove-Datastore
  

  Robert

• How to remove the error-120 code in labview?

  Hi all

  I use to communicate with the keithley 2410 13 LabVIEW and GPIB device.

  I made a program of sweeping the stairs of programming using keithley 2400 user manual, but on the interfacing it gives 'error code-120' i.e. error of digital data.

  Can someone tell me please how to remove this error and also check my program with orders.

  Concerning

  sak16091991

  Hi sak.

  you determine the exact command, which gives this message 'error - 120' of the Keithley.

  ymanglik should be able to explain the procedure now, it uses the same device with similar problems

  I guess it's related to this part of the code:

  

  What is the reason to use FormatIntoString here? Why add a constant number to string? Why not just write the number in the string constant? Where should the number be attached? Everything in the end?

  BTW. you don't need this structure of sequence - it's all in the stream!

• Remove the error of an instrument

  I'm a vi uses to communicate with an oscilloscope Tek TDP by GPIB. The vi that I use, that come with the driver for the scope, read the pulse and waveform period. The problem is that I call the VI looped several times until you get the wave shape I want. Before the wave I want to be generated it not there no pulse at all so the live ' returns an error. I want to completely remove this error. It's that I don't want it remain always displayed. Y at - it an easy way to do it. Is there a way to remove all the errors for the vi that would work, but I prefer a method that would only delete, IE not a particular error display.

  Thank you

  Chuck

  In fact, if you want to only remove a mistake, I think the best way would be to use a Simple mistake (dialog box and Palette of UI) handler.  Together, the error code top-left towards the error you want to ignore and the type of dialog box to 0 and it will remove only that error.

• Add/Remove components error and DVD driver error: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  Original title: Add/Remove components error and DVD driver error

  Yesterday, I removed several components of windows to attempt to clean my cpu. After the reboot, I noticed that my DVD drive disappeared. I tried to update the driver but told me I have the most updated version, I uninstalled and reinstalled the drive, but I still get the same error. Under Driver Details, it shows that I have a lot of drivers for my Phillips DVD player. However, the status of the device is the following: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) Click Troubleshoot to start the troubleshooter for this device. I've done the troubleshooting, and the two options has not fixed the problem.

  Then I tried to add windows components that I removed, thinking maybe that was the problem. However, when I try to add them, I get an error message that says: 'Setup cannot copy the file zClientm.ex_' it shows the location of this file as being in windows/i386, and of course, the file is located in this folder. So when I go to browse to locate the file, I find and click on it to open it, but I keep getting the same error message that the file is not found and Setup cannot continue.

  I realize that this problem seems very rare and weird, but any help at all would be appreciated. Thank you.

  Hello
   
   
  Code 39: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  Explanation of error codes generated by the Device Manager in Windows XP Professional http://support.Microsoft.com/kb/310123

   

   

  Method 1.
  Microsoft Automated Troubleshooting Services scans your computer and detects that the root causes of common problems, then automatically solves the problems that he finds and offers additional resources if the problem is not resolved. Click run now in the article below.

  Your CD or DVD drive cannot read or write media
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

   

   

  Method 2.
  Also, try the methods listed in the section below and check.
  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

   

   

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• remove the error of write protect, transfer music files to the micro sd card

  remove the error of write protect, transfer music files to the micro sd card

  on micro SD card it self you have a little pass that you can move

• Unsigned app deployment failed: "error: host name can not be null.

  Hello. "" I tried to download an app with Flash Builder 4.5 for my physical playbook unsigned, but this message has occurred: ' error: host name can not be null. The same mistake that happened when I tried to download the debugging token, but I managed to manipulate it using the command line. However, the problem with downloading mind because I can't run and test applications signed and cannot use the debug mode. Someone at - it had the same problem or knows how to get around? Additional information: Windows 7 (x 86); Flash Builder Burrito (build 287807), Playbook OS Version 1.0.1.1710

  I take that as a "I am the only one having this kind of problem" and nobody knows how to solve this (or has not yet read)

  [edit] so much worse... I just changed the IP address, this is the reason for the error.

• removal of error (0xC004C020) in window 7 for activation

  I am trying to activat window 7 online then I give the key to the error receive me 0xC004C020 how to remove this error?

  Have you tried to activate by phone?

  Activate Windows 7 manually:
  1. click on start and in the search for box type: slui.exe 4

  2. press enter on your keyboard

  3. Select your country.
  4. Select the telephone activation option and brace yourself for a real person.

  0xC004C020: http://support.microsoft.com/kb/938450

• VSAN error: host is in an active VSAN cluster but has no active VSAN service

  Guys,

  When I try to configure the vSAN cluster, I get the below error message:

  VSAN error: host is in an active VSAN cluster but has no active VSAN service

  Help, please.

  Thank you

  John

  Please follow lla: http://www.vmwarearena.com/2014/03/vsan-error-host-is-in-a-vsan-enabled-cluster-but-does-not-have-vsan-service-enabled.html

• VMotion error: host vmware cpu is not compatible with the requirements of the judgment of the VM to CPUID level register 0 x 1 'ecx '.

  Problem: I can't move my Exchange vmserver2 a vmserver1 server.

  Error: "host vmware cpu is not compatible with the requirements of the judgment of the VM to CPUID level register 0 x 1"ecx"

  
  Details:

  Vmware KB:

  * Ensure that the hosts have the same features enabled in the BIOS of the servers. If there is an incompatibility between the servers BIOS configuration even if they are physically identical, they always show a compatibility error message. The two most common to check features are the No-Execute memory Protection (NX / XD) and virtualization technology (VT / AMD - V).

  A ran the CPU utility Vmware as referenced by

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1003718

  
  "CPU that have similar features. "This means that the need of processors from the same manufacturer (AMD or Intel), be of the same family (Pentium, Xeon, etc.), and have common features extended between ESX servers involved in the VMotion.

  My results:

  vmserver1 Dell Inc.    PowerEdge 2950 2 Intel Xeon E5405 of CPU @ 2.00GHz
  vmserver2 Dell Inc.    PowerEdge 2950 2 Intel Xeon L5410 of CPU @ 2.33 GHz

  They both share exactly the same characteristics:
  FT support
  Enable VT
  VT Capable
  NX/XD
  FFXSR
  RDTSCP
  SSE
  SSE2
  SSE3

  Support Relaxations:
  NX/XD
  RDTSCP

  Relaxations unsupported:
  All THE features of the SSE
  FFXSR
  CMPXCHG18B

  In the 'Show Windows debug' it reads 'of the compatible CPU"

  This virtual Exchange machine works since Esxi version 3.5.  I am testing now vCenter Server 5.0 with version 5.0.1 on the Esxi server.

  Note: I've also been meeting random uses CPU high, leading from Windows Server 2008 to lock up completely.  I have found no trace of problems within the Windows host and Vcenter is not questions.  I have "reset" of the virtual machine in order to get the server back online.  The CPU to the top lock is random and the server can run for days with no problems. * Don't know if it's related...

  Virtual host config Exchange computer:
  Guest operating system: MS Windows Server 2008 64 bit
  version 8 of virtual machine
  CPU: 4vCPU
  Memory: 10240MB
  Overload memory: 420,61 MB
  vSphere HA Protection: protected
  Host CPU consumed: the 209 MHz

  Maps: vmserver1 watch "CPU is not compatible" CPU: 0% (none of the virtual machine running)
  Consumed host memory: 9823,00 MB
  Active memory of Fords: 409,00 MB

  Views of storage: I have a warning symbol on the QNAP iSCSI disk that hosts the virtual Exchange computer but I see no record... I'm new here...

  I understand that vmotion apply restrictions on the movement of VM compatibility to avoid it.  The components of the HA does not apply to these requirements.  We tested yesterday HA, succsessfully and this how we came to be stuck with the Exchange vm on vmserver2 and it cannot migrate to vmserver1.

  I appreciate your time and consideration,
  Tim

  It seems that you have two different processor speeds. Try the VCA mode and also check the BIOS version you and make sure they match.

• Datastore vMA host access

  Hi guys!

  I have not found the way how can I access the datastore EXSi host and copy files there at the prompt of the vMA. Do you know something?

  Thank you

  RobertJ

  The vMA/remote CLI has a sharp tool called that you can use for the operations of file etc.

  Synopsis: /usr/bin/vifs OPTIONS []
  
  Command-specific options:
     --copy
      -c
         Copy a file or a directory to another location.
     --dc
      -Z
         The datacenter context. Not required in single-host operations
     --dir
      -D
         List the contents of a datastore or host directory
     --force
      -f
         Allows overwriting of destination file for a copy or move.
     --get
      -g
         Downloads a file on the host to a local path
     --listdc
      -C
         List the paths to all datacenters available in the server
     --listds
      -S
         List datastores available
     --mkdir
      -M
         Creates a directory.
     --move
      -m
         Move a file or a directory to another location.
     --put
      -p
         Uploads a local file to the directory on the host
     --rm
      -r
         Deletes a file or a directory.
     --rmdir
      -R
         Deletes a directory. Fails if directory is not empty
  

  It is based on an older Perl script: http://vm-help.com/esx/esx3i/esx_3i_rcli/vifs.php

• cannot remove vMA ESX hosts

  I added a few guests of the vMA and activate the newspaper collection.  It collects logs for the hosts with success.  I don't want to follow these with the vMA hosts more because they are in a remote location and that it would implement a vMA at the remote location.  I use the sudo vifp removeserver servername command to remove the ESX host and they are eliminated as appropriate.  I run the vifp order mailing lists and they appear more more.  The thing is that the newspaper collection is still happening against the machines on the vMA.  I'll look in the directory/var/log/vmware and the directory for the ESX host, I deleted is still there.  I removed the directory and they immediately come with newspapers.  I'm going to rerun the command to remove the host and he says that they are already removed.

  How get rid you of the machines out of the vMA?

  You must use vilogger to disable the first control, and then remove the targets of vMA. Looks like vilogger works regardless of what VMAs think its management.

  If you have removed the targets of MAS... should not be able to connect to your targets from a distance. Are you sure that the log data is always transferred or is it simply a directory being created?

  There is a local credstore that is stored in the home directory of vi-admin /home/vi-admin/.vmware/credstore, perhaps you may need to disable it (make a backup first and move or rename)

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  repository scripts vGhetto

  VMware Code Central - Scripts/code samples for developers and administrators

  150 VMware developer

  Twitter: @lamw

  If you find this information useful, please give points to "correct" or "useful".

• NFS datastore = > no host not connected, impossible to remove

  Hello

  I have a NFS datastore (it was an ISO repository), I need to delete.   So I deleted all records from this share

  My problem is I disassembled it all hosts and the data store is still visible in my inventory and I am unable to remove it.

  When I try "Datastore Mounte to... additional host", the Wizard run in an endless loop and does not load the list of hosts.

  On my hosts, the NFS share is not visible. So nothing stuck because of a file in use.

  Have you already encountered this problem?

  Sorry found the culpit... instant on the virtual machines (with mapped CD-ROM).

• Yet another remove datastore NFS problem

  Hello, everyone!

  We have a VMware vSphere 5.1 environment and we have a datastore external NFS connected to one of the guests with distributions of the OS and other similar things. Recently on the server side NFS has been activated a firewall and its config erroneously did not all active NFS. For our data store went to the idle state. After correcting this error, I've recreated successfully NFS datastore under a new name, but now I couldn't delete the old! In the menu vSphere Client, I see all the possible orders for this data store, except take it apart a. When I use the esxcli command, it successful but after I even stranger result - vSphere Client poster: number of hosts connected to the data store - 0, number of VMs - 2. But in the 'connected' two VMs virtual CD-ROM is replaced by the client machine, there is no one (or other NFS) file data store in the properties out there!

  So, how can I manually remove such things now corrupted?

  Not sure, but has all of the active virtual machine snapshots?

  André