NFS datastore = > no host not connected, impossible to remove

Similar Questions

• NFS datastore on does not create the thick disk

  Hi Experts

  We have 4 and 5 from esx esx in our workplaces.

  I observed something strange with ESX 5, we cannot create thick disk for VM on NFS data warehouses

  While the same was collaborating with ESX 4. I'm still able to create thick disk using the same NFS volume.

  Nothing has changed in ESX 5.X? which does not allow users to create thick disk in NFS.

  Srinivas-

  NFS data with hardware acceleration warehouses and VMFS data storages are supported the following political drive of provisioning. On NFS warehouses that do not support hardware acceleration, that thin format is available. Link

• Problem of VMotion: vSphere NFS datastore UUID does not match 3.5 or in place 3.5 upgrade-> 4.0 hosts...

  I cannot vmotion VMs using a some warehouses NFS (Netapp) get the error:

  A general error occurred: Source detected that the destination has not been able to resume

  If I turned off the virtual machine, I am able to migrate, but it will not power on because one of his records is in a data store that it deems is not accessible (I guess he's using the symbolic link to validate that I reach validation errors before the vmotion). Connect to the console, I find that UUID in/vmfs/volumes data store is different between the new VMware ESX installation & 3.5 hosts or 3.5 upgraded to vsphere hosts.

  Here is a list of a 3.5 host that has been upgraded to vSphere:

  lrwxr-xr-x 1 root root 17 Oct 12 10:12 files for the exchange of stream available1 nfs - & gt; 5f7a28d4-c4c9a2da

  lrwxr-xr-x 1 root root 17 Oct 12 10:12 flow available1 nfs vmware - & gt; 13be788b-7134a5f1

  lrwxr-xr-x 1 root root 17 Oct 12 10:12 flow2 nfs swap files - & gt; 61256 has 75-a10657c0

  lrwxr-xr-x 1 root root 17 Oct 12 10:12 flow2 nfs vmware - & gt; 975 has 5815-7be104d1

  This is a new installation of vSphere:

  lrwxr-xr-x 1 root root 17 12 Oct 10:14 files exchange flow available1 nfs - & gt; 6815c0bc-4c344d45 lrwxr-xr-x 1 root root 17 12 Oct 10:14 flow available1 nfs vmware - & gt; 13be788b-7134a5f1

  lrwxr-xr-x 1 root root 17 12 Oct 10:14 flow2 nfs files of Exchange - & gt; f9c62f8d-b687a1dd lrwxr-xr-x 1 root root 17 12 Oct 10:14 flow2 nfs vmware - & gt; 975 has 5815-7be104d1

  Can you please after the release of

  esxcfg-nas - l on the two hosts?

  Maish

  Architect of virtualization & Systems Administrator

  http://technodrone.blogspot.com

• NFS datastore continues to lose connectivity

  Please can someone help me. I created a test bench using vmworksatation and built two esx servers 4. Everything is ok here I installed vc on a 2008 sp2 box and can connect ok. I also installed Windows to unix Server r3 2003 and created an NFS share. My problem is I connect and create a new DS on a drive shared NFS. Everything looks ok and then I am unable to connect to the DS because its inactive. Sometimes I can disassemble sometimes I can't. The connection is intermittent and can restore as fast as she disconnects.

  For beginners, I recommend Ubuntu because it is perhaps the friendliest beginner version (but the above command will not work). But you can also try (OpenSuSE and SLES) SuSE or RedHat (CentOS or RHEL) because they are linux distributions that are ment for the business or non-use.

  I think that they all provide graphical tools for Configuring NFS.

  --

  There are 10 types of people. Those who understand binary and the rest. And those who understand the gray code.

• F4140 does not. Impossible to remove, the software says it is not installed, but then will not re - install

  The printer is not working so I want to remove and re-install, BUT the printer is not in Add/Remove Programs (I have XP).  I downloaded the complete installation package and tried uninstalling it, but the unistall program says that nothing is installed.  Then I tried to install it but it says that the software is already installed and does not settle anything. I'm really stuck this time.  I wish that HP had a "cleaner" uses, because obviously, the registry or something is out of sync.  Help, please!

  Hey there,

  Here's how you can uninstall it by using the brush that is built into the software. I've included the two options on how to access the cleaning brush. Simply choose which option is easiest for you.

  Option 1: From Original installation CD:

  1. Insert the CD in the drive and then cancel Setup
  2. open my computer and click right then on the CD from the drive and select open
  3 open the Util folder
  4 open the CCC folder
  5. If you have an HP computer, run the L3uninstall.exe. If you have a computer not HP, run the L4uninstall.exe
  6. once the uninstall is complete, restart the computer
  7 run the Accessories\ System Tools Disk Cleanup
  8. download and install the latest version of Adobe flash player
  http://www.Adobe.com/support/flashplayer/downloads.html
  9 download drivers and full software features
  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-64285-2&cc=us&DLC=en&LC=en&OS=228&product=3235310&sw_lang=
  10. run the download to reinstall the printer

  Option 2: If the software has been downloaded and extracted to your system:
  1. type % temp % in the field of race
  2. Locate and open the folder starting with 7z (example: 7zS2356)
  3 open the Util folder
  4 open the CCC folder
  5. If you have an HP computer, run the L3uninstall.exe. If you have a computer not HP, run the L4uninstall.exe
  6. once the uninstall is complete, restart the computer
  7 run the Accessories\ System Tools Disk Cleanup
  8. download and install the latest version of Adobe flash player
  http://www.Adobe.com/support/flashplayer/downloads.html
  9 download drivers and full software features
  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-64285-2&cc=us&DLC=en&LC=en&OS=228&product=3235310&sw_lang=
  10. run the download to reinstall the printer

  I hope this helps!

  -Sean

• Windows do not install ISO in the NFS datastore

  Hi all

  I searched this forum for a few days and tried to suggestions from different positions without success. I recently installed ESXi 5.1 update 1. I have setup a NFS datastore on the same computer by using a USB external hard drive. I was able to install RHEL6 using an iso from the NFS data store. The problem is that I can't install Windows by using an iso of Windows 7. Whenever the virtual computer is booted, it aims to achieve crashes and boot TFTP. No iso standard is detected. I tried the following:

  1. guaranteed 'Connected' and 'Connect at Power On' options for CD/DVD are verified. However, I have noticed that when the virtual machine starts, the 'Connected' for Windows option becomes not controlled. This is not the case for the Linux VM.

  2. change the boot order in BIOS to the first boot from CD/DVD.

  3. uncontrolled ' connect at power on "for network adapters.

  Even after these changes, VM trying to do a start-up network and TFTP.

  The next thing I did:

  4 network cards removed from the BIOS (by changing configuration).

  For the moment, VM does not network boot attempt, but complains that the operating system was not detected.

  Few details on the NFS datastore:

  1. 1 TB external USB with 2 Configuration of partitions ext4 as an NFS share to the RHEL6 server on the same machine.

  2. NFS configured correctly because I can install from an iso RHEL6 very well.

  Am I missing something? Nothing wrong with iso of Windows. I used it elsewhere. Also tried a different iso Windows without success. Help, please. Thanks in advance for your time.

  Kind regards.

  As the ISO for the operating system files are big and sometimes take a considerable amount of clusters on the hard drive make a control office (or a scan of the drive) can fix corrupt ISO file. and to make sure that your ISO is not corrupted try to open it with Winrar and extract a file from it.

  Yours,
  Mar Vista

• Remove datastore error hosts NFS

  All, I am running this command but on each of the hosts I get the 1 first error and then it works.  No idea why?

  PowerCLI C:\Program Files\VMware\Infrastructure\vSphere PowerCLI > hostname Get-VMHost | Remove-datastore - Datastore (get-datastore-name ' Templates_I
  SOs")

  Perform the operation?
  Operation "Remove datastore." data store "Templates_ISOs".
  [Y] yes [A] Yes to all [N] no [L] no to all [S] Suspend [?] Help
  (default is "Y"): y
  Remove Datastore: 10/01/2013-11:43:09 remove Datastore has specified
  parameter was not correct.

  On line: 1 char: 50
  + Get-VMHost hostname | Remove datastore < < < <-Datastore (get - datas
  «"" Torus - name "Templates_ISOs")»»»
  + CategoryInfo: NotSpecified: (:)) [delete-Datastore], InvalidArg)
  MSP
  + FullyQualifiedErrorId: Client20_VmHostServiceImpl_RemoveDatastoreOfViOb
  ject_InvalidArgument, VMware.VimAutomation.ViCore.cmdlets.Commands.RemoveDa
  tastore

  
  Perform the operation?
  Operation "Remove datastore." data store "Templates_ISOs".
  [Y] yes [A] Yes to all [N] no [L] no to all [S] Suspend [?] Help
  (default is "Y"): y

  Do

  Get-VMHost hostname

  or

  Get-Datastore-Name 'Templates_ISOs '.

  may return more than 1 object?

  Or you run in mode "multiple" and have more than 1 connection?

  Make one

  Get-PowerCLIConfiguration

  and

  $defaultviservers

• Causes of alphanumeric password iPhone SE keybord problem often react not so impossible to connect IOS 9.3.2,and so I went back to the code number 4

  Causes of alphanumeric password SE iPhone keypad problem often react not so impossible to connect IOS 9.3.2,and so I went back to the code number 4

  What is your question?

• Home to the host windows group Group 8 Windows 7 not connecting not even with the help of the troubleshooter.

  I just got a win computer 8 and already have a Windows 7 computer, but for some reason any not connecting not even with the convenience of no help at all

  so if you can help solve me this problem please help. When I enter the password is says something like impossible connet to the home group.

  Hi Zpve,

  Let us know a few more things on the issue.

  1 to the computer on which you created the collective housing, Windows 7 or Windows 8?

  2. what version of Windows 7 do you have?

  3. what exactly is the problem you have?

  4. what happens when you try to connect to a home group?

  5. what error message do you get when you enter the password?

  I suggest you go through the links to find out how to create a group of home.

  For Windows 8:

  Homegroup from start to finish

  http://Windows.Microsoft.com/en-us/Windows-8/HomeGroup-from-start-to-finish

  For Windows 7:

  Homegroup from start to finish

  http://Windows.Microsoft.com/en-us/Windows/HomeGroup-help#HomeGroup-start-to-finish=Windows-7&V1H=win8tab1&V2H=win7tab1

  You can go through the link and look for possible causes.

  The homegroup Windows problems

  http://Windows.Microsoft.com/en-us/Windows-8/HomeGroup-problems-in-Windows

  Homegroup: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/HomeGroup-frequently-asked-questions

  Get back to us with answers from the EPF.

• vSphere client using the name Netbios on ESXi host does not connect using the credentials of a Windows session

  I have 3 ESXi 5.5 hosts, all connected to a single server vCenter, where we try to authenticate directly to the host by using the windows logon credentials. I have installation of the Administrators group of ESX and filled with the admin accounts that I want to be able to authenticate to the host. The Netbios name of the domain is tstdomain (for example) where the domain name is tstdomain.com. If I connect directly to a host and check the checkbox 'Use Windows Session Credentials', the vSphere client will default by using the Netbios name of tstdomain\adminusername and the connection will fail indicating that the username and/or password is incorrect. If I enter the domain name of tstdomain.com\adminusername, I am able to connect to the host without error.

  Does anyone know how get past that this matter have the vSphere client uses the domain name or to use the Netbios name and connect with the credentials to active directory? I looked by editing the file/etc/hosts and checked that the SPN of the host is correct in active directory with the command hostname setspn - l, with no luck on one. I also tried to change the field of research for the Netbios name of tstdomain rather than the tstdomain.com domain name, also did not work.

  Thanks in advance for your suggestions on how to correct the problem.

  Seems that this issue was due to a slow network and the connection timeout when you try to talk to the domain controller. I am able to connect with windows creds now, but the connection is very slow. I increased the default period of 30 to 60 seconds to help work around the problem.

• ' Could not connect: unable to connect to the host localhost: connection refused "on variuos orders

  On ESX 4.0.0 Update 1.

  When I run a command like "vim-cmd/hostsvc/hostsummary | "grep inMaintenanceMode" or vimsh - n - e/hostsvc/maintenance_mode_enter ' / 'vimsh - n - e
  "/ hostsvc/maintenance_mode_exit" all returned the same error message ' could not connect: unable to connect to the host localhost: connection refused.

  I checked the checked the file /etc/resolv.conf Bed & Breakfast.

  I am able to ssh on the server as well as the use of WinSCP without any problem.

  I can connect with the VI Client also without problem.

  Any ideas?

  The problem has been resolved.

  The fix:

  =====

  # vimsh-e - n/hostsvc/hostsummary | grep inMaintenanceMode

  Using the libcrypto, version 90809F

  inMaintenanceMode = false,

  # vim-cmd/hostsvc/hostsummary | grep inMaintenanceMode

  inMaintenanceMode = false,

  Rationality for the problem is these commands (vim - FCM or vimsh) were unable to communicate due to lack of xinetd process.

  # ps - ef | grep-i xinet

  root 11527 25978 0 04:30 pts/0 00:00:00 grep-i xinet

  # service xinetd restart

  #

  # Service xinetd status

  #

  # service xinetd start

  # Service xinetd status

  # /etc/init.d/xinetd ls

  /etc/init.d/xinetd

  / * But NETWORK seems to be normal on the server * /.

  # cat /etc/resolv.conf

  nameserver 172.26.6.21

  nameserver 172.25.6.51

  # ifconfig

  Lo encap:Local Loopback link

  INET addr:127.0.0.1 mask: 255.0.0.0

  RACE of LOOPING 16436 Metric: 1

  Dropped packets: 6053620 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 6053620 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:0

  RX bytes: 2021352939 (1.8 GiB) TX bytes: 2021352939 (1.8 GiB)

  ppp0 link encap:Point - to-Point Protocol

  INET-addr:164.152.87.72 P - t - P:164.152.87.64 mask: 255.255.255.255

  Up POINTOPOINT RUNNING NOARP MULTICAST metric MTU:1500: 1

  Fall of RX packets: 208 errors: 2:0 overruns: 0 frame: 0

  Dropped packets TX: 205 errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:3

  RX bytes: 18165 (17.7 KiB) TX bytes: 22314 (21.7 KiB)

  vmnic100200 Link encap HWaddr 00: 1B: 21:6 A: C9:C4

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 1383869 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 1382815 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 90351869 (86.1 MiB) TX bytes: 92106912 (87.8 MiB)

  Interruption: 97

  vmnic100201 Link encap HWaddr 00: 1B: 21:6 A: C9:C5

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 24239456 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 23905751 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 2078777971 (1.9 GiB) TX bytes: 2226266024 (2.0 GiB)

  Interruption: 113

  vmnic100600 Link encap HWaddr 00:25:5 C: 2: 75:30

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 13076343 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 5226061 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 1292112365 (1.2 GiB) TX bytes: 1224021381 (1.1 GiB)

  Interruption: 129

  vmnic100601 Link encap HWaddr 00:25:5 C: 2: 75:31

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 819469 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 770101 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 56287946 (53.6 MiB) TX bytes: 52499576 (50.0 MiB)

  Interruption: 137

  vmnic110200 Link encap HWaddr 00: 1B: 21:6 A: CA:44

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 1774795 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 1681079 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 142435399 (135.8 MiB) TX bytes: 135079293 (128.8 MiB)

  Interruption: 145

  vmnic110201 Link encap HWaddr 00: 1B: 21:6 A: CA:45

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 21079616 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 20688606 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 1859632344 (1.7 GiB) TX bytes: 1852761835 (1.7 GiB)

  Interruption: 161

  vmnic110600 Link encap HWaddr 00:25:5 C: 2: 75:32

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 39205375 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 21339531 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 32420064542 (30.1 GiB) TX bytes: 3709579479 (3.4 GiB)

  Interruption: 177

  vmnic110601 Link encap HWaddr 00:25:5 C: 2: 75:33

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 2922150 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 2110634 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 398811808 (380.3 MiB) TX bytes: 245899848 (234.5 MiB)

  Interruption: 185

  vswif0 Link encap HWaddr 00:50:56:41:76:EB

  INET addr:172.26.6.13 Bcast:172.26.6.255 mask: 255.255.255.0

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 109779 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 23715 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 10137604 (9,6 MiB) TX bytes: 21716347 (20.7 MiB)

  vswif1 Link encap HWaddr 00:50:56:40:30:F7

  INET addr:172.26.7.11 Bcast:172.26.7.255 mask: 255.255.255.0

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Fall of RX packets: 36515 errors: 0:0 overruns: 0 frame: 0

  Dropped TX packets: 4 errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 3702390 (3,5 Mio) TX bytes: 168 (168,0 b)

  vswif2 Link encap HWaddr 00:50:56:4 A: DF:1 B

  INET addr:172.26.8.11 Bcast:172.26.8.255 mask: 255.255.255.0

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Fall of RX packets: 20525 errors: 0:0 overruns: 0 frame: 0

  Dropped packets TX: 6 errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 2742990 (2.6 MiB) TX bytes: 252 (252.0 b)

  vswif3 Link encap HWaddr 00:50:56:4E:1E:24

  INET addr:172.26.9.12 Bcast:172.26.9.255 mask: 255.255.255.0

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Fall of RX packets: 26408 errors: 0:0 overruns: 0 frame: 0

  Dropped TX packets: 4 errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 3095970 (2.9 MiB) TX bytes: 168 (168,0 b)

  # / opt/ft/bin/ftsmaint lsVnd

  Virtual network device (VND) groups

  ===================================

  Status of group name

  --------------------------

  vSwitch0 ONLINE

  vSwitch1 ONLINE

  vSwitch2 ONLINE

  vSwitch3 ONLINE

  Members of the Group of VND

  =================

  Link Group Name status Interface link state speed

  --------------------------------------------------------------------------

  vmnic100200 vSwitch2 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic100201 vSwitch3 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic100600 vSwitch0 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic100601 vSwitch1 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic110200 vSwitch2 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic110201 vSwitch3 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic110600 vSwitch0 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic110601 vSwitch1 DUPLEX UP LINK

  1000 mb/s-FD

  / * Further consideration on the problem of starting XINETD * /.

  Further examination shows that the xinetd is unable to start because he believed NETWORK unavailable.

  Starting xinetd uses the contents of the sysconfig file where there was an entry incorrect "NETWORKINcesv = yes". We have corrected this entry and restarted xinetd process.

  After this correction, xinetd is restarted, the system seems to be normal.

  # cat sysconfig

  NETWORKINcesv = yes

  HOSTNAME = Server.test .net

  GATEWAY = 172.26.6.1

  IPV6_AUTOCONF = no

  NETWORKING_IPV6 = no

  #

  # cat sysconfig

  Networking = yes

  HOSTNAME = Server.test .net

  GATEWAY = 172.26.6.1

  IPV6_AUTOCONF = no

  NETWORKING_IPV6 = no

  # ps - ef | grep-i xinet

  root 27977 25978 0 04:41 pts/0 00:00:00 grep-i xinet

  # service xinetd start

  [From xinetd: OK]

  # ps - ef | grep-i xinet

  root 28119 1 0 04:41?        00:00:00 xinetd - stayalive - pidfile /var/run/xinetd.pid

  root 28239 25978 0 04:42 pts/0 00:00:00 grep-i xinet

  #

  # service xinetd restart

  [Judgment of xinetd: OK]

  [From xinetd: OK]

  # vim-cmd/hostsvc/hostsummary | grep inMaintenanceMode

  inMaintenanceMode = false,

  # vimsh-e - n/hostsvc/hostsummary | grep inMaintenanceMode

  Using the libcrypto, version 90809F

  inMaintenanceMode = false,

  #

• I have only 2 computers, a desktop computer and a laptop computer. Yet, every time I switch from one to the other, I get a message that I am already connected to TWO. It's impossible because I only have 2 and it is not connected. Any suggestions on fixing

  I have only 2 computers, a desktop computer and a laptop computer. Yet, every time I switch from one to the other, I get a message that I am already connected to TWO. It's impossible because I only have 2 and it is not connected. Any suggestions on fixing that?

  Hi Kelly,

  Maximum machines, the license can be activated is 2. Somehow, it seems that on your side the same license can be activated on any 3rd machine as well.

  Activating the license on any other machine, please select the option to disconnect all other devices and try again.

  Reference: connect and disconnect activate Cloud Creative applications (deactivated)

  Kind regards

  Sheena

• Cannot remove/remove NFS datastore because its use, but is not

  I am trying to remove an old NFS data store, but I get an error message saying that it is in use. I find the virtual machine that he believes is used, stepped through all the parameters of the virtual machine and there is nothing pointing to this NFS datastore. I also tried to remove the store of data from the command line using 'esxcfg-nas - d < NFS_Datastore_Name >. That returned an error saying "unknown, cannot delete file system. Even 30 minutes before I was access and moving data out of this data to another ESX host store. I don't know what else to try. Can someone please help?

  It also still shows up on top of the virtual machine as used storage an idle...

  The virtual machine has an active overview that was created while the virtual machine was on the NFS datastore?

  André

• Could not connect to smtp host: &lt; ip &gt;, port: 25, response: 421

  Hello
  
  I'm under java program sends single e-mail thread on. He sends about 250 emails per minute.
  Emails sent with success, but after a few hours I still get email exception "could not connect to smtp host: < ip >, port: 25, response: 421.
  
  Once this happens he has stopped coming. I had to restart the application server for this one.
  
  I wonder why emails are sent in even if e-mail exception occurs?
  
  any help will be appreciated.
  
  Thank you

  I'm not close connection to the finally block.

  So close a finally block.

  I have an old version of mail.jar (1.3.1)

  Therefore use the current version.

• Check if host are connected to Virtual Center, not a cmdlet command, but from a file

  Sometimes, I have to work on a list of hosts that are part of Virtual Center. But are are not organized in glomeruli or records or any cmdlet that I can call.

  So sometimes I run scripts based on the list generated by the user below is an example of the code how I work against the list of hosts.

  $list = Get-Content "C:\Program Files\PowerGUI\goodhost1.txt".

  ForEach ($server in $list) {($luns = Get-ScsiLun -Server $vcs -VmHost $server)}

  Sometimes these Listehotes can come from a database. The database sometimes misspells the hostname. So before working on the host I ping them and generate a list of capable host computer ping and not able ping.  Those who were not able to ping usually strike fault in the host name, and I would easily fix those and put them in a master host list.

  So in essence, my script runs when I have a master host list. But when the host is not connected in Virtual Center my script breaks. So, I have to go change my master host list and get him out of the host that the script has run on including that which has not been connected and re-run the script. Kind of pain.

  So what I'm looking for is a code example or idea on how to check if the list of my host against virtual center to see if its already connected.

  When you work with the cmdlets I use something like this

  Get-vmhost | where {$_.} State - eq 'Connected'}

  I could do something similar? With my own list.

  Thank you

  Oh sure!

  Get-VMHost | Where {((Get-Content "D:\scripts\hostsfile.txt") -contains $_.Name) -and ($_.State -eq "Connected")}
  

  Hugo

  PeetersOnline.nl